Construction of Animal Treatment Center at Hadad , Ta. Danta, Dist. Banaskantha

Excavation for foundation upto 1.50mt.Depth including sorting out and stacking of useful materials

1 and disposing of the excavated stuff as directed with in all lead & Lift (B) Dense or Hard soil. 359.00 Cu.m 157.16

Excavation for foundation upto 1.50mt.Depth including sorting out and stacking of useful materials

2 and disposing of the excavated stuff as directed with in all lead & Lift (D) Soft rock not requiring 115.00 Cu.m 276.24

Excavation for foundation 1.50mt. to 3.0 mt. depth including sorting out and stacking of useful

3 materials and disposing of the excavated stuff as directed with in all Lead & Lift (D) Soft rock not 291.00 Cu.m 300.02

requiring Blasting.

Filling foundation and plinth with sand under floors including watering, ramming and consolidating

4 dressing etc, comp. 68.00 Cu.m 444.75

Filling available excavated earth excluding rock in trenches plinth side of foundation etc. in layer not

5 exceeding 20cm. In depth consolidation each deposited layer by ramming and watering. 334.20 Cu.m 136.92

6 watering, ramming and consolidating etc. comp. 116.00 Cu.m 282.07

Applying general insecticide pest control treatment to floors, cupboards etc including labour materials

etc. complete. Using Imidacloprid 30.5 SCas Per IS 6313 part - II( (0.075% concentration by mass) is

7 recommended 10.5ml chemical diluted with 5 liters of water application 0.5 litre chemical /Sqm of 275.00 Sqm 80.84

surface is recommended as per I.S

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates

8 20 mm nominal size) and curing complete including cost of formwork in (A) Foundation and Plinth 30.00 Cu.m 3931.93

Providing and laying cement concret 1:1.5:3 (1 Cement : 1.5 coase sand : 3 graded stone aggregrate

20mm nominal size) and curing complete exculding cost of form work and reinforcement for

reinforced cement concrete work in (a) Foundation footing base of column and mass concrete

Providing and laying nominal cement concrete M-200 in R.C.C. 1:1 1/2 :3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in

column Upto plinth level.

Providing & laying cement concrete 1: 3 : 6 ( 1 Cement : 3 Coarse sand : 6 graded B.T stone

11 aggregate 20mm nominal size) Curing comp. including cost of form work in foundation and plinth. 65.00 Cu.m 3247.28

Providing and laying nominal cement concrete M-200 in R.C.C. 1:1 1/2 :3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

12 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in 28.00 Cu.m 8711.14

column for All Floor

Providing and laying nominal cement concrete M-200 in R.C.C. 1:1 1/2 :3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work (c)

PLINTH BEAM

Providing and laying nominal cement concrete M-150 in R.C.C. 1:2 :4 (1 cement : 2 coarse sand :

graded stone agregate 20 mm. Nominal size) including finishing smooth with curing complete

14 including the cost of form work but excluding the cost of reinforcement for R.C.C. work PLINTH 40.00 Cu.m 4237.96

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

15 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in 26.00 Cu.m 6414.51

BEAMS For All Floor.

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

16 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in 5.60 Cu.m 7575.29

LINTELS All Floor.

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

17 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in 2.30 Cu.m 6862.32

CHHAJJAS All Floor.

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

18 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in 56.00 Cu.m 6391.67

slabs for All Floor.

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

19 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in 3.00 Cu.m 7340.78

staircases for all floor

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Providing T.M.T. bar FE500/500D reinforcement confirmed to for R.C.C. work including bending,

20 binding, and placing. In position comp. Up to floor two level. For All Floor 35695.00 Kg 77.36

Brick work using common burnt clay building bricks having crushing strength not less than

21 Kg./Sq.m. in foundation and plinth in cement mortar 1:6 (1 cement:6 fine sand) (b) Conventional. 135.00 Cu.m 4214.33

Brick work using common burnt clay building bricks having crushing strength not less than 35 Kg./

22 Sqm. in cement mortar 1:6 ( 1 cement : 6 Fine sand ) in super structure above plinth level upto floor 146.00 Cu.m 4502.54

two level ( for G.F ) Conventional

Half brick masonary in common burnt clay building bricks having crushing strength not less than

35kg./sq.cm. in cement mortar 1:3 (1 cement : 3 coarse sand ) with 2nos. of 6mm dia mild steel round

23 bars every three coarse embedded in cement mortar in superstructure for Ground floor 37.00 Sqm 750.76

(Conventional)

Providing and fixing door Double shutter 35 mm.thick flush door teak wood beading 75 x 35mm

including both side in situ laminate with 18mm thick including granite frame width 6 Lever Mortice

24 lock , SS Aldrop 30cm long, SS Handle size 60 Cm Long, Tower Bolt size 20 cm etc. as per detail 5.00 Sqm 5836.79

colour & pattern approved by this office including necessary anodized alluminum fixtures and

fastenings.

Providing and fixing door Single shutter 35 mm.thick flush door teak wood beading 75 x 35mm

including both side in situ laminate with 18mm thick granite frame 6 Lever Mortice lock , SS Aldrop

30cm long, SS Handle size 15 Cm Long, Tower Bolt size 20 cm etc. as per detail colour & pattern Sqm

approved by this office including necessary anodized alluminum fixtures and fastenings.

Providing & fixing FRP Frame size100 x 50mm and 35mm think FRP depress pannel shutter having

extra reinforcement on sides ad edges and in gel coat finish. The cores of the shutter is to be filled up

with intected fire extinguishing grade polyurethane wooden pieces for stiffening and also for taking

26 hinges and fixtures. The FRP shutter is to be water proof, weather proof, termite proof and resistance 4.00 Sqm 2087.06

to mild acid / Alkali including S.S hinges with necessary screws and alluminium fixtures and

fastenings & Fastener Sleeve.

Providing and fixing Anodized Alluminum Section Jindal Deluxe Sliding Window System C (30mm)

series sction memebers THREE track window section bottom track 20837, frame top & side

27 shutter frame top rail & bottom rail 20993, side rail 20553, lock rail 20550 with 5mm thick 34.00 Sqm 3081.51

transparent plain float glass, with transparent silicon sealant with allu. anosized coated fittings and

fixture etc complete.

Providing and fixing standared extruded of alluminium section of size 63.50 x 38.10 x 1.95 mm @

Wt 1.094Kg / Rmt with colour Powder Coated alluminium frame with 5 mm thick transparent bronze Sqm

colour tinted float glass as details etc complete for Fix window.

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm @

Wt. 0.643 Kg/mt) with colour anodized alluminium frame for ventilation with 5 mm thick frosted

29 glass as details etc complete for Ventilation {Colour as directed by Engineer in charge except black & 3.00 Sqm 1175.56

Alluminum section and glass

Providing and fixing Safty grills of required pattern for windows 12mm dia M.S. round Bar at

required spacing M.S. Flat 25mm x 5mm thick as per design and hold fasting with coach bolts

30 including one coat of primer and Shall be Painting with Enamel Paint and Colour approved by as per 1500.00 Kgs 111.40

site Engineer etc complete.

Providing and laying Machine cut, Free edges, Machine polished Granite stone slab 18 mm thick

{Single piece not more than 150 cm } for stair steps and riser as per design incl. full moulded round

31 front edge & 1 cm nosing & necessary groobe on trade of steps laid on 20 mm thick cement mortar 90.00 Sqm 3223.92

1:6 (1 -cement : 6 coarse sand ) jointed with grey cement slurry including rubbing and polishing etc.

Providing and laying machine polished machine cut Kota stone slab ( 60 x 45cm Size) flooring over

20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime

32 putty :1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match 8.00 Sqm 1018.88

the shade of slab including rubbing and polishing etc. complete. (A) 25mm thick

Providing and laying 60 x 60cm Soluble Salt Vitrified tiles 8 to 10 mm thick with pattern colour &

Shade as detailed approve by architect ( 10% Dark colour tiles Pattern ) in flooring treads of steps

33 and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand) finishing with 207.00 Sqm 1120.36

flush pointing in white cement.

Providing and laying 60 x 60cm Soluble salt Vitrified tiles 8 to 10 mm thick with pattern colour &

Shade as detailed approve by architect ( 10% Dark colour tiles Pattern ) in skrting risers of steps and

34 dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement 12.00 Sqm 1195.02

Providing and laying 30cm x 30cm in size Ceramic tiles 6mm thick in flooring treads of steps and

landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with

flush pointing in white cement

Providing and laying 30 x 60Cm size premium printed glazed tiles 6mm thick in skrting risers of steps

36 and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement 434.00 Sqm 1000.51

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Provding and filling the joint with epoxy grout 3 mm width and 8 to 10 mm deep, including cost of

necessary materials, PVC spacers, filling grout and cleaning etc complete as directed by engineer in

charge. { Colour and Pattern as directed by engineer in charge.}

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick with

grade of concrete M300 pnumatic compressed / vibrated mechanically and as per approved design

38 Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling and filling the joint with 46.00 Sqm 701.90

sand in proper line and level as per guidlines of IRC : SP 63-2018 etc. Complete

Providing and laying water proofing tretment with chaina mosaic tiles flooring over avg 40 mm

C.C. 1:2:4 ( 1 Cement, 2 sand, 1 Kapchi 20mm + 3 grit 6mm to 10mm ) bedding for maintaining

slope for plain and curve surface & 12 mm to 20 mm of broken piece of ceramic / glazed tiles ( one

or more color as directed ) to be laid over cement mortar bedding of C M 1:3 (1 cement : 3 sand )

containg one Kg. of water profing materials per bag of O P C at plain or / and slops and to be Sqm

tempered to bring mortar ceramic up to surface with using white cement and colour pigment

including rounding of junctions and extending them up to 15 cm along the wall and curing with

bends any pattens or design as per drawing and cleaning by using oxalic acid etc complete.

Providing and laying Mirror polished Machine polished Grenite stone slab 18mm thick for doors &

windows sill & Jams clading as per design including full moulded round front steps & 1cm nosing &

40 necessary groove on trads of steps ;laid on 20mm thick cement mortar 1:6 ( 1 cement : 6 coarse sand 46.00 Sqm 3338.05

) jointed with gray cement sluury including rubbing and polsihing etc. complete.for Doors / windows

sill & jams clading.

Providing 20 mm thick double coat mala cement plaster on interior brick / concrete work for

plastering comprising of base coat of 12 mm thick cement plaster in cement mortar (1 Cement :

41 coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 Coarse 509.00 Sqm 293.04

sand) finished with trovel including scaffolding curing etc. complete. For Ground Floor

Providing and fixing chiken mesh jali with square of 12.50 x 12.50 mm of 25 gauge at junction the

42 Brick.masonary and reinforcement cement concrete member including fixing materials scaffolding 100.00 Sqm 92.92

labour etc. complete

Applying two coats of putty & two coats of primer of approved brand and manufacture on new wall

43 surface to give an even shade including thoroughly brushing the surface free from mortar dropping 509.00 Sqm 40.59

and other foreign matter and sand papered smooth.

Wall painting one coats of primer of approved brand (three coats) plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an even shade including throughly

44 brushing the surface free from mortar droppings and other foreign matter and sand papered smooth. 509.00 Sqm 125.73

20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting

of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M.

45 1:1 (1-cement : 1-sand) with 1cm x 1cm groovs as per pattern sample approved by the engineer 932.00 Sqm 320.70

incharge etc. complete.

Providing and fixing 90 cm high Stainless steel railing made from anticorrocive S S pipe of 50 mm

dia (16Gauge) as hand rail with S S 38 mm dia (16Gauge) as a vertical support fixed in RCC slab at

46 1.2m c/c including three horizontal S S pipes of 25 mm dia (16Gauge) at eqal distance fixed by 30.00 Rmt 3245.13

18.75 mm dia (16Gauge) S S pipe including accessories as per detailed drawing as directed etc.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the

help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings Rmt

etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of

all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the

48 help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings 55.00 Rmt 91.84

etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of

all materials. [B] 25mm dia.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the

49 help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings 20.00 Rmt 148.12

etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of

all materials.[D] 40 mm.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the

50 help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings 160.00 Rmt 195.67

etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of

all materials.[E] 50 mm.

Providing and fixing uPVC Heavy Duty Handle valve of aprroved brand and Quality with required

fitting and adhesive incl. fixing the same with new pipe line as directed by engineer in charge. (B)

25mm dia.,

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Providing and fixing uPVC Heavy Duty Handle valve of aprroved brand and Quality with required

52 fitting and adhesive incl. fixing the same with new pipe line as directed by engineer in charge. (C) 4.00 Nos 685.79

40mm dia.,

Providing and fixing uPVC Heavy Duty Handle valve of aprroved brand and Quality with required

fitting and adhesive incl. fixing the same with new pipe line as directed by engineer in charge. (C)

50mm dia.,

Providing, laying and jointing in true line and level 75 diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI

14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other

with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x

54 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as 40.00 Rmt 933.05

directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints

and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of

the following outside Dia. Low densidy, complete with special flange compression type fittings, wall

55 clipsetc. including making good the wall ceiling and floor.(A) 110mm dia. 50.00 Rmt 338.95

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI

14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other

with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x

56 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as 100.00 Rmt 1053.73

directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints

and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI

14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other

with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x

57 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as 50.00 Rmt 834.38

directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints

and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing MS Z clamp on Wall or celling for Pipe Fitting including all type necessary

58 fittings and accessory etc. completed as per directed engineer in charge. 145.00 Nos 75.75

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the

59 following nominal diameter of self cleansing design with C.I scread down or hinged grating including 5.00 Nos 733.26

the cost of cutting and making good the walls.

Providing and fixing screw down quarter turn heavy duty bib taps of following size (A) Brass

chromium plated screw down bib tap (i) 15mm dia. ( Plumber, Mark, Escco or equivalent brand ) Nos

Providing and fixing CP brass Quarter turn pillar tap, capstan head screw down high pressure with

61 screw, shanks and back nuts (A) 15 mm dia {Jaquar< Plumber, Mark Long pipe or equivalent brand} 4.00 Nos 308.73

Providing and fixing wash basin with pedestal of std. Height with single hole for pillar tap with C.I or

M.S brackets painted white including cutting cutting holes and making good the same including C.P.

62 brass waste and waste pipes and bottal trap (A) Vitreous China: (ii) Flat Back washbasin 550 mm x 2.00 Nos 1890.72

400mm size.In colour.

Pro. & Fix. wash down water closet (anglo indian W.C pan of Vitreous china Patern.) with integral"

p " or " s " trap and PVC flushing cistern with a pair of C.L.I. Or Mild steel Brackets, complete with

fittings such as lead value siphon, 15 mm. Nominal size brass ball valve with polythene float, C.P.

Brass handle unions and couplings for connections with inlet, outlet and over flow pipes, 40 mm. dia.

63 flush bend including cutting holes in walls and making good the same connecting the flush bend with 2.00 Nos 3223.92

cistern and closet etc comp incl plastic sheet cover including jointing trap with pipe in cm 1:1 (a )

Vitreous china in white or color

Providing and fixing Special Needs Range CRUSE SET, EWC, 710 x 370 x 810 mm, New Cat No:

S1021113 S Trap, S1021114 P Trap, S1060106 Cistern, B1520118 Soft Close Seat Cover,

B1810112 Twin Flush Fittings, S2040101 Wash Basin 510 x 400 mm, F9030451 Spatula Lever

basin mixer, B2210106 Wall mounted Grab bar 600 mm long, B2210106 Wall mounted Grab bar

600mm long, B2210108 Wall mounted Hinged rail 750 x 750 {Cera or equivalent} as

directed by Architect Office {SUGAMYA BHARAT Instruction}

Providing erecting and fixing double coated 4-layer tough virgin plast ISI water tank of required

65 capacity each with all necessary fittings and connection etc. complete on terrace. 2000.00 Litre 10.61

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick

A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs

67 with C.P. brass scews.(B) 600mm x 20mm size. 4.00 No 616.42

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I.

cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps.(B)

68 150mm x 100mm size P of R type 4.00 No 1246.92

Providing and fixing CP brass screw down stop cock of approved quality 15mm size with adjustable

69 wall flange..or as per instrction of engineer incharge. 6.00 No 205.83

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light

duty) 455mm x 610mm intenal dimensions, total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse

70 sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick 4.00 No 2932.93

with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete

etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light

duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse

71 sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick 4.00 No 3660.76

with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete

etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or

two inlets.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light

duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slab with 1:2:4 mix (1-cement :2- coarse

sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete

etc. complete.(iii) Inside dimensions 600mm x 850mm and 450mm deep for pipe lines with three

or more inlets

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an

required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of

loose powdered materials.etc complete

Constructing Sandwitch Platform of 16 to 18 mm thick Polished Black Granite at top and 25 mm

thick Kota stone slab using cement mortar 1:3 for sandwich and fitting at bottom & edges with

waterproof rigid adhesives including macking necessary grooves in walls with Vertical Kotastone

74 30 mm x 2 No sandwitch thick every 60 cm centre to cenre including all labour material of 10.00 Sqm 5866.08

approved quality incl. full moulded round front edge fixed in wall for partition and jointed with grey

cement slurry including rubbing and polishing etc. complete

Providing and fixing stainless steel kitchen sink glossy ASIS 304 grade and 1 mm thick with overall

size 610mm x 460mm x 330mm deep having bowl size 510mm x410mm x 200mm of Nirali or

equivalent brand with all fittings CI or MS brackets painted white or fixing on stone base including

cutting holes and making good the same brass valve and fisher union fitting including all necessary

Providing thoruting or plaster drip and moulding to R.C.C. chhajja.

Providing 12mm wide groove throating / notch in plaster including finishing the same etc. complete

77 for all height. 273.00 Rmt 15.15

Providing and fixing in position 300mm high , 150mm wide englsih letter made from 1.0mm thick

78 stainless steel sheet as directed by enginer in charge with all necessary tolls & plants etc. complete. 20.00 No 707.00

Providing and fixing in position 150mm high , Englsih letter made from 1.0mm thick stainless steel

79 sheet as directed by enginer in charge with all necessary tolls & plants etc. complete. 50.00 No 404.00

Providing and laying cement concrete 1:4:8 (1cement : 4 coarse sand : 8 Machine Crushed stone

80 aggregates 40 mm. nominal size) and curing complete excluding cost of from work in :(a) Foundation 33.00 Cu.m 2653.42

and plinth

Providing and laying controlled cement concrete M-200 and curing complete including the cost of

81 form work but excluding the cost of reinforcement for reinforced concrete work in Wall 4.00 Cu.m 5577.22

caps/Copping Ground Floor

Providing T.M.T. bar ( Thermo Mechanically treated Bars) reinforcement confirmed to IS-1786 for

R.C.C. work including bending, binding, and placing. In position comp. Up to floor two level. For Kg

Ground Floor

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Providing and fixing mild steel door with 40 x 40 x 6 mm angle for frame and for shutter frame 30 x

30 x 3 angle. For windows frame of angle 35 x 35 x 5 & for shutter windows 25 x25 x 3 mm size

angle and 18 gauge sheet for panels & 10 mm dia bars at 10 cm c/c for grill and 40 x 6 mm flats on

83 edge of shutter, & 20 x 6 mm binding patti, including one coat of primer and two coats of oil painting 225.00 Kgs 109.08

etc. comp. as per detail / as directed by Engineer in charge.

Providing 15mm thick cement plaster ( Mala Trowel finish) in single coat on brick/concrete walls for

84 interior plastering upto floor two level and finished even and smooth in (i) Cement mortar 1:4 (1- 346.00 Sqm 215.65

cement:4-sand) for Ground Floor

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering

upto floor two level and finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

85 including finishing with a flating coat of neat cement slurry etc. complete. for Ground Floor 25.00 Sqm 215.32

Providing 20 mm thick Water proof cement plaster for sunk in single coat on bricks/ concrete wall

for interior plastering upto floor two level finished even and smooth (ii) Cement mortar 1:3 (1-

cement : 3-sand) and mixing waterproofing materials of approved brand and manufacture in cement

mortar in proportion recommended by the manufacturer for All Floors.

Providing and laying white glazed tiles 6mm thick in flooring treads of steps and landing laid on a bed

87 of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush pointing in white 12.00 Sqm 955.41

Providing and laying white glazed tiles 6mm thick in skrting risers of steps and dedo on 10mm thick

88 cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry 41.00 Sqm 1030.57

Providing and laying hand dressed polished blue Kota stone slab flooring over 20mm (Average) thick

base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 laid over and jointed with grey

89 cement slurry including rubbing and semi miror polishing with emery No. 600 etc. complete. (A) 14.00 Sqm 1018.88

25mm thick

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on

90 undecorated wall surface to give an even shade including throughly brushing the surface free from 67.00 Sqm 125.73

mortar droppings and other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an

91 required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of 507.00 Sqm 73.83

loose powdered materials.etc complete

Providing cement vata (10cm. x 10 cm. size) quarter round in cement mortar 1:1 including neat

92 cement finishing, watering etc. complete. 16.00 Rmt 24.28

Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less than 35Kg.

Providing and fixing S.S Butterfly valve of IS aprroved brand (C) 50mm dia., No.

Providing and laying cement concret M250 1:1:2 (1 Cement : 1 coase sand : 2 graded stone

aggregrate 20mm nominal size) and curing complete exculding cost of form work and reinforcement

for reinforced cement concrete work in (a) Foundation footing base of column and mass concrete

Providing and laying nominal cement concrete M-250 in R.C.C. 1:1 :2 (1 cement :1coarse sand :

graded stone agregate 20 mm. Nominal size) including finishing smooth with curing complete

96 including the cost of form work but excluding the cost of reinforcement for R.C.C. work in column 6.00 Cu.m 7005.36

Upto plinth level.

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

97 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in 4.00 Cu.m 5577.22

Wall caps/Copping Ground Floor

Providing & fixing 0.80 mt. high SS razor fencing using 1.70 mt. long Ms angle 40 x40 x 6 mm size

as a pole having 0.80mm stragh and 0.45 mt both side inclined part as datail drawing & desing fixed

at 3.00m c/c in CC 1:2:4 (double angle at turnig with support) as per drawing in brick masonry wall

with three horizontal lione at bottom part and four line with double ring consertium medium blade

98 having coil diameter 450 to 600 mm 3-5 spiral clip. core diameter 2.50mm tap thickness SS Razor 110.00 Rmt 558.71

wire made form SS galvenized as per drawing with GI staples including one cost of premix red lead

paint and two cost of white enamel oil paint of asian /berget make raw silk shed etc complete as

directed by enginner in charge .

Supplying & installing of Dry Chemical Powder type 6 Kg. Capacity fire extinguisher as per I.S.

99 ISI. Mark with necessary fittings etc. complete. 8.00 No. 2626.00

Providing Carben doxide type fire extinguisher 4.5Kg. Capacity with I.S.I. Mark and test certificate

100 of explosive deprtment of Nagpur 8.00 No. 6060.00

Providing and laying ordinary cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone

101 aggregate 20mm nominal size) and curing etc. complete including the cost of form work but 3.00 Cu.m 3638.79

excluding the cost of reinforcement.(a) Footing.

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Box cutting the road surface to proper slope and chamber for making a base for road work including

102 removing the excavated stuff and depositing on the road side slope as directed up to 50 mts. Lead. 99.00 Cu.m 109.08

Supplying and laying, spreading and compacting coarse clean sharp specified sand (C.B.R. not less

than 10%) below sub base course including carraige of material spreading in uniform layers manually

on prepared base and compacted with power roller to achieve desired density including all materials, Cu.m

labours etc. complete. and spreading coarse clean sand as directed.

Providing and laying 300mm thick W.B.M. with B.T.M.C. metal 40mm to 63mm size two layer of

150mm thick including using 25% stone dust as filler including spreading watering consolidation and

104 rolling etc. complete at site of work including loading unloading and filling the boxes etc. complete. 36.00 Cu.m 1166.55

Providing and laying Nominal cement concrete M.250 C.C.1:1:2 (1 cement : 1 coarse sand :2 20mm

B.T. Stone aggregate) and curing complete including the cost of formwork and reinforcement for

105 reinforced concrete work in(A) Foundations, footings, Base of columns and Mass concrete 25.00 Cu.m 4517.73

Compaction and finishing of cement concrete road by tremix process, providing extra labour charge

for tremix ( Vaccum dewatering service ) process on cement concrete road surface by using vaccum

dewatering pump floater surface vibrator including making groove 5mm width and filling with Sqm

polyvynile polymer and rough finish to surface as per instruction including leveling etc. complete.

Providing and fixing junction board of M.S.plates and angles as per standered IRC design including

fixing in C.C. 1:4:8 with necessary excavation , painting, figuring and lettering on board etc. comp.

Providing 15 mm thick cement plaster in single coat on brick/concrete walls for interior plastering

upto floor two level and finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

including finishing with a flating coat of neat cement slurry etc. complete. for Ground Floor

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick with

grade of concrete M300 pnumatic compressed / vibrated mechanically and as per approved design

109 Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling and filling the joint with 96.00 Sqm 701.90

sand in proper line and level as per guidlines of IRC : SP 63-2018 etc.Complete.

Clearing and grubbing road land including uprooting rank vegetation grass bushes, shrubs, sapling

and trees girth up to 300 mm removal of stumps of trees cut earlier and disposal of unserviceable Cu.m

materials(D) By mechanical means in area of thorny jungle

Excavation for foundation upto 1.50mt. depth including sorting out and stacking of useful materials

and disposing of the excavated stuff as directed with in 50m.Lead (B) Dense & Hard soil

Providing and fixing 150 x 150 x 3.2 mm thick M.S. pipe parking shed post & Rafter & Cross, MS

× 50 x 2mm pipe purlines with necessary M.S. plate 8mm hick including cutting, bending, grinding,

112 welding , drilling for nut bolts including painting two coats of oil painting over primer coat etc. 4.10 Qtls 9108.48

Providing and fixing of Ridge flashing for roof panel shall be made out of 0.5 mm thick pre coated GI

sheet. The Precoated sheet shall be of minimum 240 mpa steel grade confirming to IS 14246:1995

and shall have zinc coating of minimum 120 gsm as per IS:277:1992, 5-7 microns epoxy primer on

both side of the sheet and polyester top coat 15-18 micron. The PPGI Sheet shall have plastic

113 protective guard film of minimum 25 microns to avoid scratches during transportation. The ridge 36.00 Sqm 867.39

shall be fixed to the steel members by pop rivet or self drilling/self stitching fastners @ maximum

450 mm c/c along length of capping/flashing etc complete.

Demolition including stacking of serviceable materials and disposal of unserviceable material with all

114 lead and lift. (1) R.C.C Work 8.00 Cum 1082.35

Demolition of brick work and stone masonory including stacking of serviceable materilas and

115 disposal of unserviceable materials with all lead and liift (2) In cement Mortar 53.00 Cum 562.89

Dismentaling of tiled of stone floors laid in mortar including stacking seviceable materials and

116 disposal of unseviceable materials with all lead and lift. 47.00 Sqm 49.12

Dismentling steel work including distemering and stacking the materials with all lead and lift.

Dismentling doors, windows, ventilators etc. (wood or steel) shutters including chowkhats

118 architraves, holdfasts and other attachment etc, complete and stacking them within all lead and lifti) 15.00 No 192.09

Not exceeding 3 Sq.M. in area.

Dismentling C.I. pipes G.S. W.pipes abd A.C. rain water pipes with fittings and clamps including

119 stacking the materials with all lead and lift ( for any dia, of pipe) 28.00 Rmt 76.68

Dismantling santtary fittings like wash basin. W.C. pan Indian and European type, flushing tank etc.

120 including stacking the materials with all lead and lift. 8.00 No 414.23

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected, with Pts.

necessary Lamp holder/ceiling rose / H.D.Connector as directed.(f) with medium class Rigid PVC

pipe and accessories erected concealed in wall/ceiling complete Cat.III Make:- Honeywell, L&T,

Crabtree, Indoasian, M.K, Anchor

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked

1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of

pipe erected with 6A Modular type switch and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following type erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured/metallic/white front plate modules erected on

/ in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.(f) with

medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat. III

Make:- Honeywell, L&T, Crabtree, Indoasian, M.K, Anchor

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

123 modules erected on / in wall / ceiling with following type accessories Cat. III Make:- Honeywell, 15.00 Pts. 257.55

L&T, Crabtree, Indoasian, M.K, Anchor

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

124 necessary connections as per site situation directed by Engineer In charge.

(1)One No. SP 6 Amp. Cat.III Make:- Honeywell, L&T, Crabtree, Indoasian, M.K, Anchor 5.00 Nos. 151.50

(2) One No 5 pin plug Cat.III Make:- Honeywell, L&T, Crabtree, Indoasian, M.K, Anchor Nos.

(3) Two Pin/RJ-11 Telephone Socket [A] For One Gang Cat.III Make:- Honeywell, L&T,

Crabtree, Indoasian, M.K, Anchor 2.00 Nos. 160.59

(7) Blank Plate Single Cat.III Make:- Honeywell, L&T, Crabtree, Indoasian, M.K, Anchor

(8) Computer RJ-45 socket Cat.III Make:- Honeywell, L&T, Crabtree, Indoasian, M.K, Anchor

(9) 16 Amp. SP one way switch Cat.III Make:- Honeywell, L&T, Crabtree, Indoasian, M.K,

Anchor 11.00 Nos. 180.79

(10) 6/16Amp. Universal socket Cat.III Make:- Honeywell, L&T, Crabtree, Indoasian, M.K, Anchor

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with

125 adhesive solution & Clamps with following dia of pipes, in approved manner as directed

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes,

126 Check-nuts etc. complete of following sizes.(2) 25 mm 20.00 Mtr. 21.21

Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid

material with ignition free and flame proof confirming BS with necessary end caps Internal and

127 external bend, flat bends, coupler, tee etc..All necessary accessories and measuring of following 10.00 Mtr. 428.24

sizes(2) 100 mm x 50 mm trunking

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with

sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of

128 following size(A) With medium class Rigid PVC pipe and accessories (b) 2 wire 2.5 sq. mm Make- 390.00 Mtr. 82.82

RR Kabel, Havells, Avocab, KEI, Johnson, Polycab

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

129 conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(a) 2 wire 4 sq. mm Make- RR Kabel, Havells, Avocab, KEI, Johnson, Polycab Mtr.

(h) 4 wire 6 sq. mm Make- RR Kabel, Havells, Avocab, KEI, Johnson, Polycab

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing

pipe of following size (Specifically for control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and bolts if required.

(f) One wire 10.00 sq. mm

(e) One wire 6.00 sq. mm Mtr.

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked

copper wires of following size to be erected as directed. (e) 1.50 Sq.mm 3 core round PVC sheathed Mtr.

Make- RR Kabel, Havells, Avocab, KEI, Johnson, Polycab

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction[C]

132 CAT - 6 150.00 Mtr. 47.47

Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE insulation

twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer

133 Jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following 40.00 Mtr. 20.20

size of conductors & nos.of pairs. With necessary connections. [A] Conductor Size 0.5 mm (a)

Unarmoured (2) Two Pairs

Providing & erecting Switch board for Computer or electric apparatus consisting of following

modular type accessories mounted with PVC / Metallic concealed/open box with single mounting

base frame covered with textured/metallic /white front plate,modules erected with necessary

connections as directed

133 1 no. 6A/16A universal plug-switch combined. 6.00 Nos. 1133.22

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type AccessoriesCat. III Make:- Honeywell, L&T, Crabtree,

Indoasian, M.K, Anchor

Decorative call bell Ting-tong box type 250 volts complete erected

Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage, minimum

15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser, mounting suitable

135 for E14 / E27 / B22 lamp holders, pf >= 0.5(A) LED Lamps integral type, with PC diffuser suitable 3.00 Nos. 112.11

LAMP holder

(ii) 5 to 8 watts Cat.III Make;- Jaquar, Wipro, LT, Havells, Luker

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

136 LED driver efficiency > 85 % 28.00 Nos. 373.70

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of

ranges shown.)(A) Tube Light with integral driver (iv) 22-24 Watts, Surge - 2KV,IP-20, conventional

4 feet Cat.III Make;- Jaquar, Wipro, LT, Havells, Luker

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of

3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT

3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver

137 efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below description have 11.00 Nos. 4997.48

capacity between the ranges shown.)(A) Street Light (IP-65), Surge protection -4KV integral and

,Light must have 440VAC line supply with over-voltage protection. (ii) above 48 to 60 Watts Cat.III

Make;- Jaquar, Wipro, LT, Havells, Luker

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply

with over-voltage protection. (iv) above 90 to 120 watts Cat.III Make;- Jaquar, Wipro, LT, Havells,

(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot and spun aluminum

canopy fixed with opal polycarbonate, pipe arrangement for vertical mounting driver and accessories

wired upto terminal block.IP 65 (ii)32-40W Cat-lll Make;- Jaquar, Wipro, LT, Havells, Luker 2.00 0.00 4819.72

Approved make Four Pole LT Heavy Duty Switch Disconnector Fuse Unit Cubical type for panel

mounting complete with operating mechanism suitable to operate on 415V A.C. With HRC fuses of

138 suitable load confirming to IS. 13947 (Part I & III). of following capacities (c) 125 Amp Cat.III 1.00 Nos. 6120.60

Make- Indoasian, L&T, Schneider,ABB

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Supplying & erecting approved make Four Pole 415V change over switch interior for panel mounting

with operating mechanism A.C.23 duty confirming to IS for(C)100-125A Cat.III Make- Indoasian,

139 L&T, Schneider,ABB 1.00 Nos. 7790.13

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking

capacity ICU of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all internal connections,

140 spreader tinned copper & complete erected in existing 16 G.M.S. housing. ICS=100% of 6.00 Nos. 6173.12

ICU only Cat III Make- Indoasian, L&T, Schneider,ABB

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having normal current rating 125A. with Fixed thermal &

magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III

Make- Indoasian, L&T, Schneider,ABB

Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper Busbars with four

equal Nos. of electrolyte bus having current density not more than 1.6 Amp. / sq.mm (Rated current /

cross section area) duly wrapped with colour insulating tape for phase sequence of following current

142 carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each bar, 1.60 Rn.Mtr 1961.42

erected in existing cubical panel with necessary connections.(A) Suitable for 100 Amp. Capacity

providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark Make-

143 Indoasian, L&T, Schneider,ABB 19.00 Nos. 270.68

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V

A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS

144 8828/1996 with ISI Mark Cat.III Make- Indoasian, L&T, Schneider,ABB 34.00 Nos. 112.11

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having

10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity (B)

145 Amp. Cat.III Make- Indoasian, L&T, Schneider,ABB 4.00 Nos. 330.27

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in existing box having following capacity (b)40 Amp. Nos.

Cat.III Make- Indoasian, L&T, Schneider,ABB

(c)63 Amp. Cat.III Make- Indoasian, L&T, Schneider,ABB

Plastic enclosure fitted with DIN rail suitable for incorporating One / Two nos. MCB

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of

148 MCB to be used) suitable for (A) single phase incoming and horizontal single phase outgoing (b) 1.00 Ea. 1492.78

sheet steel double door (IP-43) (iv)12 way Make- Indoasian, L&T, Schneider,ABB

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI)(b)

149 sheet steel double door(ii)6 way Make- Indoasian, L&T, Schneider,ABB 2.00 Nos. 2913.85

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase

V,50Hz. having characteristic of quick action & tripping with all advance feature & do not

150 incorporate any electronic component. for following Max. rating erected as directed (ii) 40Amps. DP 7.00 Nos. 2235.13

Cat. III Make- Indoasian, L&T, Schneider,ABB

Providing and erecting metallic vitrified danger notice board as per language suggested by engineer

151 incharge for MEDIUM VOLTAGE installation to be erected as per IS-2551. 1.00 Nos. 69.69

Providing and erecting Annealed bare Copper wire 8 to 16 SWG.

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia. galvanised iron pipe

153 with coupling and buch buried in specially prepared earth pit complete with necessary 8 SWG earth 10.00 Nos. 368.65

For using salt and charcoal / coke as required for pipe type earthing.

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded

by highly conductive compound with high charge dissipation suitable for following type of

applications with chamber and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having

back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter

testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long

time Necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type

cubical panel board necessary IP-42 and above protection as per approval from engineer incharge

made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories , supporting angles/ flats channel including cutting,

bending, drilling, welding, riveting with internal partitions & cable alley as per requirements &

instruction of engineer-in-charge with erection of supplied switch gears, BUSBARS, suitable size of

inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates,

sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary ventilation,earthing strip complete. The Panel

shall be painted with epoxy powder coating. (The rates excludes the cost of switchgears, bus bars,

inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be

measured excluding base beams) The panel shall be supplied with following approved manufacturers

with following size.

(A) locally fabricated panel board (i) with 350 mm depth

2.10 Sq.Mtr 10468.65

Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper

size of M.S. angles,square,round, flats, bars, channels, sections complete with cutting, welding,

grinding & finishing duly painted with one coat of red oxide with erection on site as per direction of Kgs.

engineer in charge with necessary grouting, cementing, plastering & finishing complete.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor

for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of

158 cables (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) Make- RR Kabel, , Avocab, KEI, Johnson, 10.00 Mtr. 378.75

(B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core) Make- RR Kabel, , Avocab, KEI, Johnson,

Polycab 40.00 Mtr. 220.18

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of

159 following size of cables(B) 4 core 6 Sq. mm Make- RR Kabel, , Avocab, KEI, Johnson, Polycab 265.00 Mtr. 126.25

(C) 4 core 10 Sq. mm Make- RR Kabel, , Avocab, KEI, Johnson, Polycab Mtr.

Making trench in soft soil of suitable width of 90 cm deep for laying cable or locating the fault all

160 over the run and back filling the same and making the surface as normal ground. 160.00 Mtr. 55.55

Drilling the road without breaking the road surface (Asphalt) for laying of cable for feeding power

161 supply by making up to following size of holes at both ends complete.(A) Up to 100 mm bore dia 10.00 Mtr. 492.88

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at

162 required depth in existing trench for laying of cable. below ground / road surface for enclosing 160.00 Mtr. 62.62

cable (A)50 mm outer dia

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc for following size of cables.(B) 2 to Nos.

4 core 6 Sq. mm

(C) 2 to 4 core 10 Sq. mm Nos.

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber

ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following

size of cables.

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

(C) 3 & 1/2 core 70 Sq. mm

(B) 3 & 1/2 core 35/50 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size

165 evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium

plated nut bolts in an approved manner.

(C) 16/25 Sq.mm. Nos.

(D) 35/50 Sq.mm. 8.00 Nos. 20.20

(E) 70 Sq.mm. 6.00 Nos. 25.25

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing ISI

mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with

aluminium blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be approved by Nos.

Engineer in charge)) Make:- USHA, BAJAJ, CROMPTON, HAVELLS, ORIENT

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly

167 painted for fan complete with proper insulation without leakage and earthing. 15.00 Mtr. 108.07

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm

length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected

concealed in Ceiling with necessary finishing.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box.

Supplying & erecting approved make low noise decorative exhaust fan having square frame ABS

body with inbuilt lowers & square frame250mm with 1350 RPM Cat.II Make:- USHA, BAJAJ,

170 CROMPTON, HAVELLS, ORIENT 3.00 Nos. 1366.53

Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole should be

made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of terminal plate of min 6mm Hylam

sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable foundation (Included) as per details

171 given by manufacturer considering site requirement.(C) 5 Mtr. Long 70 mm Top X 130 mm bottom 10.00 Nos. 6874.06

dia, 3 mm thickness with 200mmX200mmX12mm base plate, 4-M16 Bolts and 600mm long with

necessary G.I. J Bolts .Approx Pole weight 46 kg

Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out

approx. 2mm thick box complete with Bakelite connector strip 5way(3P+N+E),DIN rail for mounting

mob & hinged doors as per requirement having locking arrangements with mounting clamp with

172 nuts, bolts & washers suitable for erection on pole with cable clamps& earth bolt of following size of 8.00 Nos. 515.10

box.(B) 250mm x 200mm x 100mm [deep]

Supplying and erecting Street light pole bracket comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve tubing of approx. 45cms.length and suitable

for 76.5mm/80mm/require size of pole top having nuts and bolts for fixing the brackets and having

spread of 0.5 mtr. Length with 110 deg.with vertical plane and suitable welded stiffener reducer and

173 nipple with check nut complete painted with one coat.of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms.

[B] Double Arm Bracket 0.5 Mtr Nos.

[A] Single Arm bracket 0.5 Mtr 10.00 Nos. 491.87

Supplying & erecting IP 55 grade following size section pillar fabricated from joint less M.S. Sheet

with angle iron legs made from jointless M.S. Angle with cable clamps to be buried in ground to have

appropriate erection to work uniform until erected with cement concrete foundation and 45 cm high

bricks work finishing with plaster etc. hinged double door internally supported on both side, with

internal and outside looking arrangement with look and keys in duplicate 35 x 35 x 5 mm M.S. Angle

of Two Nos. one is welded and other with nut and bolt for erecting Bakelite sheet. Painting the

Section Pillar inside and out side with three tank powder coated paint. section pillar roof should be

without joint with water leakage proof & tested as per IP 55 test & followed by IS 2147 of 1962(B)

75 X 60 X 45 cm section pillar fabricated from 16 Gauge MS Sheet with angle iron legs 45 cm long

made from 35 X 35 X 5 mm thick MS angle.

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Supplying and erecting HYLAM sheet on existing angle iron frame.for following thickness(D) 8mm

175 0.40 Sq mtr 1541.25

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V

+ 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also

comprised permanent ON/OFF switching. Programming switches & housed in fire proof

176 thermoplastic enclosure & transparent cover erected as required with necessary connection erected as 1.00 Nos. 3168.37

directed. Make- Indoasian, L&T, Schneider,ABB

Supplying & erecting power contactor ,AC3 duty for time switch complete erected as per direction

177 Cat III (D) 4 pole 440V 40 Amp. Make- Indoasian, L&T, Schneider,ABB 1.00 Nos. 2782.55

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per

hour @ an ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚C within a hour,

The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing

unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet Nos.

& outlet connection. The body of water cooler will be made from Stainless Steel. Make- VOLTAS,

BLUESTAR, USHA

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder

coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable

buster DC pump capacity 80 psi, mention with 40 psi inline type post carbon filter auto low & high Nos.

pressure switches with following size of storage tank & LPH capacity & erected as directed [C]

Ltr / Hr with 150 psi 2 nos booster pump

Supplying and erecting approved make panel mounting type Digital Voltmeter having 3 digits LED

display, 0 to 750 AC Volts range erected on existing panel board with all connection, wiring etc

180 .with manufacturers calibration certificate. 2.00 Nos. 1275.63

Supplying and erecting approved make panel mounting type Digital Ammeter having 3 digits LED

display, external CT operated, calibrated for 0 to 1000 Amps suitable to operate on 500 Volt AC

181 erected on existing panel board with all connection, wiring etc .with manufacturers calibration 2.00 Nos. 1558.43

certificate.

182 existing panel board with necessary connections. 4.00 Nos. 317.14

Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio 15 VA burden

erected in existing CRCA box duly secured with insulating materials connected to the meter

Supplying and erecting approved make suitable panel indicator LED type lamp, lens cover, complete

184 erected with necessary connections. 6.00 Nos. 43.43

Providing & erecting open well horizontal mono block pump set with cast iron body, complete for

three phase submersible motor having[A] For 1.5 HP 3 phase open well horizontal mono block pump

set suitable for 190 LPM @ 20 mtr head suitable for 40 mm dia delivery pipe Cat.II Make:Duke,

Lubi, Amrut, Uneel

Supplying and erecting Direct on line starter with 30 Amp. (resistive @ 230v) power relay and with

to 5/ 4 to 10 / 8 to 20 amp. Range C.T. Operated electronic overload relay in engineering grade

plastic enclosure for 3 ph 415v 50 HZ A.C. motor up to 7.5 HP with high voltage protection (above

480 v) and under voltage protection (below 330 v) current sensing single phasing protection. Reverse

phasing protection, inverse current characteristic overload protection with indication for On, OL,

HV,LV SPP in a single unit with feather touch start / stop push button, high temperature with

standing Bakelite terminals complete erected on P.W. Block with necessary connection. [Cat.II]

Lowering of submersible motor pump set at the depth of following ,complete with required. Nos. and

size of casing pipes erected by means of proper chain pulley block & pipe wrenches after checking of

threads of each pipe with coupling to take the load of the pump set and pipe assembly filled up with

water (d)For Open well Horizontal submersible pump set for sump well (i) 1 HP to 5 HP

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper

cable approved make of following Size. (A) 3 Core x 1.5 Sq. mm. Make- RR Kabel, , Avocab, KEI,

188 Johnson, Polycab 15.00 Mtr. 65.65

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating

material, water proofing material, & making the joint complete. (A) Up to 10Sq. mm

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall

Profile, Front Cover : High Transmission Low-Iron Tempered Glass (AR Coated), High efficency and

positive power tolerance Pmax: 0/+5, Module Efficiency should be approx. 19.5%-22%, Normal

operating temperature 45'C, Junction Box with Waterproof IP67 & MC4 Compatible and Enclosed

with Bypass diodes, 100% Electroluminescence test to ensure error free Modules, Thep. temp. co-

efficient of the PV module shall equal or better than -0.45%/degree C. Solar PV modules of minimum

190 fill factor 75% to be used. Unit Production:- More than 4.5 Unit /kw /day (Actual)(1Year Avg) With

10 year Product warranty and 25 year Linear Power Warranty includes all mechanical and electrical

parameters of the Solar panel. Modules must be complied to the DCR(Domestic content

requirements).

The Ration of AC to DC is 5:6 for the Installation capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% - 98.9%, O/p

Frequency: 50/60Hz, Operating Altitude (m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%,

Operating Tempreture Range: -25~60°C, Integrated protection of Inverter are Anti-islanding

Protection, Input Reverse Polarity Protection, Insulation Resistor Detection, Ground fault protection,

Residual Current Monitoring Unit, Output Over Current Protection, Output Short Circuit Protection,

Output Over Voltage Protection, PV array string fault Protection. Protection Degree: IP65, User

Interface LCD & APP, Datalogger & Communication: GPRS / Wi-Fi.

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated,

Residual Current Monitoring Unit Integrated, Output Over Current Protection Integrated, Output

Short Circuit Protection Integrated, Output Over Voltage Protection Integrated, Protection Degree:

IP65, User Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting

Structure: The mounting (Rectangular pipe / square pipe / circular pipe) with requisite cross bars,

nuts and bolts, etc. shall be Hot deep galvanized with minimum 80micron coating. The Rectangular /

square /circular hollow pipe section used for the structure should have a minimum thickness of

mm. other than above, the material thickness should be minimum 2.5 mm. A certificate of a structural

engineer certifying the strength and stability of the mounting structure to withstand the weight and

wind speed of 150 km/hour throughout the life span of 25 years of the system, shall be submitted by

the vendors.

Hot Dipped Galvanized steel coils. suitable arrangement for base plate for foundation , solar panel

mounting, the structure should be suitable for carry the load of solar panel,wiring, sprinkler system

etc. with necessary foundation work/wall mount, j bolt, anchor fastner etc. the nut bolt used for

installtion of stucture should be (SS 304) quality.The ground clearance of the bottom most edge of

solar panel shall not be less than 300 mm to 1200 mm or as per site’s technical/feasibility

requirement.

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of System with

necessary Swichgears (Suitabel size and protection of ACDB & DCDB), inter connecting wiring,

earthing system as per the CEIG drawing approval, lightining arrester system as per the CEIG

drawing approval, all liasoning work with various gov. dipartment like state nodal agency,DISCOM &

CEIG is included in agency scope (Excluding All charges namely GEDA Application fees, Solar

connectivity Charges, Meter connectivity Charges, Meter testing Charges and system

stability/strenthning charges.)

(B) Grid Tied Solar Power System: 7 - 10 kW (3 - phase) 8.00 kw 44081.45

Total Tender amount

Rupees One Crore Seventeen Lakh Eleven Thousand Seven Hundred Eighty One And Paise Twelve Only

I/am we/are willing to carry out the work at _____% above /below _____________ percent (should be written in figures and words) of the estimated rates mentioned above. Amount of

my/our tender works out as under.

* Estimated amount put to tender

Deduct :_____ % Below Rs.________________ Add :_____ % Above Rs.________________

Net Rs. ______________________ Total Rs. ______________________

In words ___________________________ In words __________________________

1. The Contractor Shall Exhibit a board with deatiled specification and details of work as directed by the Engineer-In-Charge for which no Extra Payment shall be made.

2. The labour crss will be deducted as per prevaling Rules i.e 1% of the work done.

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

3. GST and Income tax TDS will be deducted at a Source while making Payments of bills.

4. In all RCC items in Rate Analysis Standard cement Consuption has been taken as per Govt.G.R: PRC -10/2017 cement consumption/16/c, Date: 11/05/2017 as stated i. S.O.R

therefore in RCC Items where there is a changed as per actual mix design the cost of diffrence of cement consumption have been deduvted from the rate of orignal item at the rate of

input rate mentioned in all the tender.

5.Credit Amount Rs 19440.00 for Credit for Dismantled materials will be deducted from First Running account bill.

Above all items of " Schedule-B" with iem Description,Unit,Rate & Amount Have verified by me and found Order.

Deputy Executive Engineer Executive Engineer

R & B (Pan) Sub Division R & B (Pan) Division

Danta Palanpur