ADDITION ALTERATION TO CERTAIN OFFRS JCOS ORS MD ACCN AT BAREILLY UNDER GE EAST BAREILLY

Amount

ITEM OF B/R

Dismantling frame truss n.exc 10 M complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position , framed work complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) insulation boards / slabs / blankets of any thickness, including cover fillets complete all as specified and directed.

Taking down cement plaster including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer - in - Charge.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

Demolition of concrete of any description and in any position not otherwise specifically provided for

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

Dismantling of 100mm bore cast iron/ pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

Dismantling of 75mm bore cast iron / pvc drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed .

Taking up or down15 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Taking up or down20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

Dismantling water tanks exc 250 & n exc 500

Dismantling water tanks exc 500 & n exc 1000

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation etc and n exc 1.5m in depth and getting out complete in Loose/soft soil.

M&L for cement concrete Type C2 1:3:6 (40mm graded aggregate) in foundations, filling and mass concrete.

M&L 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed

M & L 25 mm thick PCC 1:2:4 type B0, using 12.5mm graded aggregate as in floors to receive surface of tile complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M&L Non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm in floor etc set and jointed in neat cement slurry with spacer not exc 5mm pointed and filled with coloured tile grout of approved make complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm on vertical surfaces etc set and jointed in neat cement slurry with spacer not exc 5mm pointed and filled with coloured tile grout of approved make complete all as specified and directed.

M & L 9 to 10 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L for vitrified ceramic dark shade tiles 10 mm thick square/ rectangular) polished area of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as spd

M&L for vitrified ceramic dark shade tiles 10 mm thick square/ rectangular) polished area of each tile not exceeding 0.36 sqm in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L Machine cut pre polished kota stone slab flooring 20-25 mm thick and size exc 0.16 sqm jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and treating the surface incl complete complete all as specified and directed

M&L for 20-25 mm thick Machine cut pre- polished kota stone slab as in riser and steps, skirting in full length in single peice without joint, with groove cutting in double line of stair width laid over cement screed and jointed with rubbing and treating the surface incl bull nosing complete all as specified and directed. surface incl full round bull nosing edging complete complete all as specified and directed.

M&L 20 mm thick Granite of black colour (tablee rubbed and polished) as in windows cill & cooking platforms and like in cement mortar (1:4) including form work , pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as spd as directed

M&L for red stone slab 25mm to 35 mm thick dressed true and square,in one length not less than 60 cm and n exc 120 cm as in plinth protection etc in cement mortar 1:4 punched dressed on exposed faces and self faced on the embedded unexposed beds and joints exposed edges chamfered or rounded as directed and including screed bed of 20 mm thickness in cement mortar 1:6 all as specified and directed

M&L for reinforced cement concrete M-25 (20 mm graded aggregates) (nominal mix) (nominal mix) as in slabs supported on wall like including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items). (nominal mix) as in slabs supported on wall,landing, balconies, shelves and like including bonding agent , complete all as specified (reinforcement to be measured & paid under respective items).

M&L form work to chajja, weather shade, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified.

M&L form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete, complete all as specified.

Supply and fix TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0, complete all as specified.

ditto above item but 6 mm to 8 mm

M &L for PCC (1:2:4) type B-0 using 10/12.5 mm graded stone aggregrate laid over roof slab after applying cement slurry for filling undulationations finished even and smooth without using extra cement complete all as spd and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed by Engineer-in-Charge.(Note : Water proofing liquid shall be measured and paid separately)

Supply Integral water proofing Liquid .

M&L PCC 1:5:10 type E-2 (40 mm brick aggregate) as sunken sub base of floor fillings with broken brick agg .

S&F 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in, built in cement mortar 1:6 complete all as specified and directed.

M & L Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in mortar 1:6 complete all as specified and directed

M&L rendering 15 mm thick in ready mix internal sand faced cement plaster on brick or concrete surfaces including providing as per manufacturers specifications, surfaced finished even and fair complete all as specified and directed.

M& L for 15mm thick ready mix external sand faced cement plaster on brick or concrete surfaces including providing & mixing water proofing compound as per manufacturers specifications, surfaced finished even and fair complete all as specified and directed.

M&L rendering 5 mm thick ready mix sand faced cement plaster in CM 1:3 as on concerete surface on ceilings finished even and smooth complete all as specified and directed by Engineer-in-Charge.

M&L for Removal of Existing Waterproofing Treatment and clean the surface (a) Bonding Coat: Cleaning the surface with wire brush, water jet etc to remove dust, dirt etc. On clean surface applying a bonding coat of Asian paints smartcare Multi Purpose Polymer mixed with cement (1:1:5) to reduce the existing surface porosity and as a bond coat for the new surface sceed on the top of the same. (b) Resurfacing: Applying and laying a avg 15mm thick layer of cementitious polymer modified mortar on the top of the bond coat as per manufacturer's instructions in existing gradient/ slope. Polymer will be added @ 8% to the weight of cement. Solid content of the polymer not less than 54%. The newly constructed surface to be cured with clean water at least for 10 days before applying WP membrane. (c) Surface Preparation: The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of screed shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar, Making of Coves/ vata at the juction/ corners in using MPP polymer mixed with cement: sand as per manufacturer's instruction for mortar & water curing the same, after curing period of 72 hours proceed with application of Polyurethane coating.

(d) Liquid Applied WP Membrane: Application of Asian Paints two component Epoxy Primer (Resin 8. Hardener, on the cleaned surface for bonding of Polyurethener with the existing concrete surface. 33% water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3 (Resin: Hardner). Epoxy primer will be done at consumption of 0.2 Kg per Sqmt. Supplying and applying waterproofing treatment to terrace area with single component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer's specifications and application methodology. The same coating shall be applied in two coats achieving an avg. thickness of 1 mm. The coating shall have a dual combination of 280% elongation. The Material will be applied @ coverage 1.2 Kg/ Sqmt. A 10 years Company Back Warranty to be provided after completion of the work. The applicator must show the company authorization.

S&F for Pressed steel frames Size 125mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed

S&F 40mm flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides as directed by engr-in-charge'.

S&F factory made single extruded WPC (Wood Polymer Composite) pre-laminated both side Solid moulded Flush Door Shutter of 35mm size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), Calcium Carbonate and natural Fibers (Wood Powders/ rice husk/ wheat husk) and Non toxic additives (max toxicity indes of 12 for 100 gms) having min density of 650 Kg/Cum and screw withdrawal steength of 1800 N (Face) & 900 N (Edge) Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category with property of being Termite/ Borer proof. Water/ Moisture Proof, Fire retardant and fixing with stainless steel four Nos but hinges of 100 mm size on each shutter with necessary full body threaded star headed coounter sunk SS Screws. Butt Hingesa and screws will be paid seperately. All as per direction of Engineer-in-Charge, Materia test certificate and authentication should be compulsory provided by the manufacturing company.

S&F 35mm thick factory made glazed and skeleton door shutters open rebated of first class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, divided into squares edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed by Engineer-in-Charge. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring. Fixed in floor

S&F for 18 mm thick termite resitant and water proof, both side prelaminated 100% WPC Board one side plain white lamination total thickness not more than 22 mm thick, as iun cup board shutters, with wardrobe/ finch lock & PVC lipping on all exposed edges of same texture and shade, with complete all as specified and directed. Note: 1. Design & layout of wardrobe and pattern/ colour of lamination to be approved by GE. 2. Thickness of laminated not less than 1mm for inside plain white type & 1.5 mm for outer decorative type. The laminate shall be fixed to base with approved adhesive as per manufacturer's instructions and machine pressed to ensure proper bonding with base ply and avoid air pockets. 3. Frame to be fixed to walls, soffits & base of cupboard with fasteners.

S&F for 12 mm thick termite resistant and water proof , both side prelaminated wooden plywood both side plain white lamination , total thickness not more than 15 mm , as in cupboard shelves & partitions including powder coated aluminium cleat (colour of powder coated to match colour / shade of laminate) and as in fixing to sides of cupboard, soffits & base of cupboard with SS fastner also including PVC lipping on all exposed edges of same texture & shade to match the laminate complete all as specified as directed . Note: 1) Design & layout of wardrobe and pattern / colour of lamination to be approved by GE. 2) Thickness of laminated not less than 1mm for inside plain white type. The laminate shall be fixed to base with approved adhesive as per manufacturer's instructions and machine pres.

S&F for 9 mm thick termite resistant one side prelaminated wooden plywood with plain white lamination, fixed on back side of wall of cup board with SS fastners complete all as specified

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet , suppling & fixing in opening as per specification & drawing

S&F 30 mm thick factory made both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F for steel windows/ventilators conforming to IS-1038 with side hung shutters including box type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete without glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Wire cloth shall be measured and paid for separately).

S&F for steel windows conforming to IS-1038 with side hung shutters including box type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete with glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Glass shall be measured and paid for separately).

S&F for steel ventilators fixed type, with glazing bars complete welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed by Engineer-in-Charge. (Note :- Glass shall be measured and paid for separately).

M&L for 3mm thick sheet glass ordinary/ frosted quality and glazing with oil putty in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

S&F factory made uPVC white/dark colour sliding window three track made of extruded profiles.three track sliding frame(88mm X 52mm),reinforcement frame(30mmX18mm)X2 Nos,Sliding window sash(42mmX67mm),reinforcement sash(30mmX18mm),sliding mesh sash(42mmX57mm) reinforcemnt mesh sash(26mm X 10mm),sliding interlock for door(one vertical length in each shutter((45.5mm X 28mm),sliding glazing bead(24.5mmX16mm)Profiles of frames and sash will be mitered cut and fusion welded at all corners,including drilling of hols for fixing hardware and drainage of water etc. making arrangement for fixing of hardware,EPDM gasket,1.2+_0.2mm thick galvanized steel profile to be inserted in required profile,frame will be fixed to the wall with 8mm X 100mm long fasteners,all complete and as directed(Hardware hinges and fitting to be paid separately)

S&F Powder coated aluminium sliding windows and frame with movable shutter ( sliding on minimum two PVC roller of best quality on two tracks Aluminium composite panel shutter fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :68.4x38mm X 1.15 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) Aluminium beading - 0.7mm thick (v) Aluminium fittings such aluminium suitable handle with auto interlock cap with suitable size . (vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F Powder coated aluminium ventilators box type with louvers & wire mesh fixed with neoprene rubber gasket, aluminium beading, clips. Frame made with powder coated aluminium section of size as appended below (i) frame :45.2mm x35mm X 1.15 mm (ii) Aluminium beading - 0.7mm thick (iii) Glass louvers depth 6 inch. Blade Angle: 38 degrees and thickness of blade 2.02 mm with 106.25 mm spacing. (iv) Aluminium neccessary fittings complete as required. (v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed.

S&F for Stainless Steel (AISI 304 grade ) non magnetic multilayer nickel chrome plated for multipurpose utensils container of following size in each kitchen :- (a) Plain basket of size 510x470x100 or 520x485x100 mm OR 486X500X100 - 1 No (b) multi size plate basket of size 510x470x150 or 520x485x150 mm or 436 x 500 x200 mm ( clear depth 500 mm -01 Nos (c) cutlery basket,with perforated bottom & side of compacted /slots for holding cutlery of size 510x470x100 or 520 x485x100 mm or 144x 468 x50mm ( clear depth 500 mm of ) -01 Nos (d) Plain basket of size 510x470x200 or 520x485x200 mm or 486x500x200 mm -02 Nos (e) Pull out with 02 baskets each of size 150x485x80 or 100x485x80 mm -01 Nos , (f) SS Dust bin ring -01 Nos, (g) Telescopic channels as required & including frame work ,handles etc as reqd & all as specified sample & design to be approved by GE.

M&L for rolled mild steel in roof trusses (framed) trussed purlins, crane gantries, rails and fastenings including distance pieces, cleats etc complete all as specified and directed.

M&L for rolled mild steel in rolled section as in main and cross beams, hip and jack rafter, purlins where connected to comman after and running rails, fixed with angle cleats or other connecting plates complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws with washers as specified

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Providing & fixing false ceiling with semi perforated 12mm thick micro tegular edged GRG False Ceiling tiles at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanized iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, wall band,shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M&L for RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels & wall band over 1.5m span etc complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in chajja, beams etc complete all as specified and directed.

S&F magnet catch with striking plate including letting in and fixed, complete all as specified.

S&F in repairs 40mm dia and 75mm long, extruded fancy type SS handle for kitchen cup boards shutters, cabinets, crocery shelf drawers fixed with nuts , screw and washer of mild steel bright finished , complte all as specified.

S & F 300 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed

S & F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed

S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed.

S&F 100 mm size butt hinges medium weight stainless steel colled rolled complete all as specified and directed by Engineer-in-Charge.

S&F 300mm size ordinary mild steel , rat tailed rod pattern spring including roller and roller plate welded to mild steel frame.fixed in repair complete all as spd & directed.

S&F 300 mm long aluminium sliding door bolts plate type with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed

S & F hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with SS screw complete all as specified & directed.

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F 1000 litres, rotational moulded polyethylene of white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system ), hoisted and fixed in position complete all as specified and directed

S&F 500 litres, rotational moulded polyethylene white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size of M S Tasla with suitable locking system ), hoisted and fixed in position complete all as specified and directed .

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia steel water tubing galvanized medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium gradeconcealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed

S& F Vitreous Cliina wash basin, angle back, size 600x480mm white, including Pedestal, excluding taps, waste, chain and plug and porcelain stopper but including brackets cutting for and pinning in ends of brackets or erecting stand

M& L 40mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed

S& F fancy type 15 mm bore dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F in Vitreous China table top wash basin of suitable size including SS bottle trap, HDPE waste pipe including fixing on counter with SS waste coupling complete all as specified.

S&F in repairs Brass chromium plated wall mixer 3 in 1 , 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and directed.

S&F in repairs Brass chromium plated wall mixer 2 in 1 , 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and directed

S&F in fancy type 15mm dia chromium plated fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as directed.

S&F in repair fancy type brass chromium plated coloured toilet paper holder vitreous china complete all as specified

S & F in repair fancy type 150mm size square brass CP shower rose all as specified.

S&F in repairs 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified as directed.

S&F in repairs 15 mm dia bib tapcast copper alloy with butterfly handle , screwed down for iron pipe or for brass ferrule and fixed complete all as specified as directed.

S&F in repair fancy type 15mm dia brass chromium plated mixer for mixing hot and cold water screwed down for iron pipe and fixed to WHB including taking out existing mixer from old WHB, complete all as specified.

S&F in repair fancy type chromium plated brass two way bib cock suitable for 15mm bore pipe complete all as specified and directed

S&F stainless steel tubular towel ring including apair of CP brass bracket complete all as specified.

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm , complete all as specified.

S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified.

S&Fin repair fancy type stainless steel towel rack size 600mm including apair of brass bracket complete all as specified &directed by Engr in charge.

S&F chromium plated brass tubular towel rail 20 mm dia, D type for wash hand basin centre holed fixed to iron pipe complete all as specified and directed.

S & F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified.

S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified .

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair vitreous china coloured European type WC with "P" or "S" trap 1st quality including connection to drain and fixing bolts complete all as specified.

S&F in repair vitreous China wall mounted Rimless Water closet 1st Quality size 570x390x365 mm with Conceiled Flushing Cistern and CP lever for Cistern including soft close Sear cover, connection to drain, joint between WC and wall sealed with silicone and fixing bolts complete all as specified.

S&F in repairs, PVC low level flushing cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed

S & F Brass CP health faucet with 8mm Dia 1.25 Meter Long Flexible Tube and Wall Hook screwecd for iron pipe fancy type long body all as specified and directed.

S&F Brass CP Hand Shower with 8mm Dia 1.2 Meter Long Flexible Tube and Wall Hook Screwed for iron pipe fancy type long body all as specified and directed.

S&F in repair PVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 100 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fitting complete all as specified and directed by Engr-in-charge.

S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fittingcomplete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F in repairs Stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plat rack, complete all as specified.

S & F for 0.8 mm thick stainless steel kitchen sink size 590x460x230mm undermount, single bowl (bowl size 540x410x230 mm) , incl waste pipe & SS coupling, washers etc. complete all necessary fittings all as specified and as directed

S & F for 0.8 mm thick stainless steel in graceful glory range ,anti scratch, satin finish of popular range kitchen sink over all size 990x459mm , double bowl size 400x340xx200 mm incl waste pipe & SS coupling, washers etc. complete all necessary fittings all as specified and as directed .

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type droppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and as directed

M&L for Providing & injecting chemical for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in a portion with cement mortar 1:2 to match the existing apron complete all as specified and directed.

M & L for Post Construction anti termiteTreatmentAt points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same as specified and directed.

M & L for Post Construction anti termiteTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor soil complete as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 Grade St.-240

M & L for cutting chases of hanging chajjas, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of sunshades, shelves, lintels, Chajja ( up to IInd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and as directed.

Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposingthe reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx50 mm (10 mm gauge welded mesh ) & tack , securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @3% by weight of cement and construction fibre as per manufacturer instruction cleaning & removing of waste meterial etc as dirply two coat of Water proofing liquid at interval of 8 hours cure for the surfaces complete all as spd as directed

S&F for 0.71mm thick Aluminium plain sheeting Alloy 31000 H4, stucco embossed finish with fixed with coach screw and Aluminium washer in roof and wall etc. with end laps stitched with 25x6mm G.I. bolts at 20cm apart gap to be with thermocol sheet incl dismantled also all as spd as directed

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and fastening and fixing FE 290 Gde E-165 complete all as spd as directed

S & F 1.25 mm thick Mild steel, plain black sheet in steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles etc as required complete including cutting out of existing sheet if required all as spd as directed

M&L for two coats of elastomeric compound i.e super latex of Fr fixit Pidilite-302 Super latex/ Fosroc-brush crete/ Cico Tape Crete on concrete or brick masonary surface after cleaning (vertical or horizontal) by removing all the loose mortar laitance dirt, dust etc by chisel, hammer, wire brush, jute, brush and air blower complete all as specified and directed.

Demolition of Reinforced Concrete of any description and in any position not otherwise specifically provided for

M&L for providing precast cement concrete type B-0 (1:2:4) (using 12.5 mm graded stone aggregate) louvres and jallies, 50mm thick (measured solid), including all mouldings set in CM 1:4 complete all as specified and directed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint ordinary tintover and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation old steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint ordinary tintover and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wooden or wood based surfaces Surfaces of any description, over 10cm width or girth or girth when unconnected with other painting or when painted in a diferent tint and applying one coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed.

M&L applying two coat of white putty on new surface and applying one coat of exterior water based primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by jpaint manufacturer and as mentioned in PS and accessories fpr applying distemper, should be able to spray in hard to reach areas and penetration of distemper, on the surface to achieve excllent application using limited manpower complete all as specified and directed.

M&L for complete removal of existing treatment, preparation of old decorated plastered or unplastered surfaces of walls / roof projections including facia,cornices etc. and applying two coat of white putty and applying one coat of primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by paint manufacturer and accessories for applying Primer, should be able to spray in hard to reach areas and penetration of Primer, on the surface to achieve excllent application using limited manpower complete all as specified and directed. Note : - Sanding of old decorated surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer.

M&L for applying two coat of exterior weather proof 100% anti fungal acrylic smooth emulsion with silicon additives that offer anti algae high performance exterior wall finish applied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying exterior weather proof paint, should be able to spray in hard to reach areas and penetration of exterior weather proof paint on the surface to achieve excellent application using limited manpower complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash on walls complete all as specified and directed.

M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism ) with sanding pad of appropriate grit to make surface clean ,free from dust ,loose paint etc by skilled labour and applying two coat OBD on wall with airless electric sprayers over a coat of primer applied using airless electric sprayer over one coat of wall care putty of 1mm thickness complete all as specified and directed. Note:-Application to be done through authorised applicator of manufacturer.

M&L for two coat OBD on newly plastered wall surface with airless electric sprayers over a coat of primer applied using airless electric sprayers over one coat of wall care putty of 1mm thickness complete all as specified and directed. Note-Application to be done through authorised applicator of manufacturer

M&L for complete removal of existing treatment and applying of two coat OBD on ceiling with airless electric sprayers over a coat of primer applied using airless electric sprayers over a coat of putty of 1 mm thickness prepared and sanded with electrically operated sanding machine. Application to be done through authorised dealer

M&L for preparation of new surface of plastered and applying of two coat OBD on ceiling with airless electric sprayers over a coat of primer applied using airless electric sprayers over 1 mm thick plaster of paris (approved by GE)prepared and sanded with electrically operated sanding machine. Application to be done through the authorised applicator of manufacturer complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of oil bound distemper complete all as specified and directed.

M&L for preparing newly plastered walls surfaces and applying two coats of cement base paint complete all as specified and directed.

Sewage Disposal

Excavating in trenchs, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out Hard dense soil.

Returning, filling Hard and dense soil in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated Soil material n exc. 50m and depositing wheredirected at a level n exc. 1.5 m above the starting point

M&L for cement concrete type D2 (1:4:8) (using 40 mm graded stone aggregate) in foundations filling and mass concrete.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6).

Concrete bed to drain pipe in Cement concrete 1:3:6 type C-2 including packing under, and haunching against the sides ofpipes after they are laid and tested in 150 mm dia bore of pipe

M/L PCC 1:2:4 type B1 using 20mm traded stone aggregate as in Coping /benching including necessary form work and finishing all exposed surfaces of concrete . All as directed.

M & L 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches and jointes as specfified

Providing precast cement concrete set in Cement mortar 1:4 type B1 (1:2:4 ) (20 mm aggregate ) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces

M&L for rendering 15mm thick fair faces of brick work or on concrete surfaces of External in CM(1:4) finished the surface even and smooth wihtout using extra cement all as specified and directed.

M&L for rendering 10mm thick fair faces of brick work or on concrete surfaces of internal in CM(1:6) finished the surface even and smooth wihtout using extra cement all as specified and directed.

Fencing & Gate

Excavating in post holes (or similar holes) each n. exc. 0.5 cum, gettting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25 cm, watering and removing surplus soil to a distance n exc. 50 mtr and making good surface.

M&L for looking mirror 5mm thick of size 300mm x 900mm fixed to wooden surface with wooden fram of size 30mm x 20 mm section complete all as specified and directed.

Dismantling of old fencing any type of mesh and size

Dismantling of posts or struts(wood steel or RCC) any section including taking out embedded portion and making good disturbed natural ground

M &L PCC (1 :2:4) type B1 using 40mm agg as in post holes in CM 1:6

S&F Angle iron fencing post and struts including cutting tops to shape as directed drilling holes, notching for wire etc, flat iron fillets (for securing wire mess etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 410-0 or Fe 310-0 including round bars etc complete all as spd & directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and fastening and fixing complete FE 290 Gde E-165

Fixing only chain link fencing including line wire any mesh size and type of standards raills, starining bolts ewtc including provisioning of binding wire complete all as spd & directed .

Supply only chain link MS galvanised fencing any size or type complete all as spd & directed .

M&L Cement concrete type B2 1:2:4 (40 mm graded aggregate) in foundations, filling and mass-concrete complete all as spd

Formwork to sides of Rough finished surfaces of concreteof concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as spd & directed .

Mild steel screw bots (machine made ) with hexagonal or square heads at one end and screwed the other each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10 cm but not exc 15 cm and 15mm dia complete all as spd & directed..

Preparation of new steel surfaces exc 10 cm width or girth and applying two coats of syntetic enamel paint (ordinary tint) over one coat of red oxide of zinc chrome primer complete all as spd &directed .

Road & Path

M& L 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed

M&L Sand filling under floors or in foundation including watering and consolidation complete all as spd

M&L for cement Concrete coloured interlocking paver blocks shall be factory made with casting in rubber/pvc moulds & compacting on a vibro table assembly and shall be cured in curing tank for atleast 14 days and then air dried before use. The paver block shall be confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade. Approved design, shape, size and colour of top layer complete all as specified and directed.

M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required

E/M Portion

Taking down carefully copper/ aluminium point wiring ie. light, fan, socket or power/points complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. and removing the items from site to store for taking credit (Credit for above items should be made as per conditions seperately) and making good disturbed surfaces of ceiling, walls, floors, etc complete all as specified and as directed.

Taking down electric/Electronic meter and disconnecting, removing to store for keeping in safe custody for refixing etc complete all as specified and as directed.

Taking down main switch / MCB DBs including MCBs etc of any size and removing the items from site to store for taking credit (Credit for above items should be made as per conditions seperately) and making good distrbed surfaces to match with the existing surfaces of walls, floors etc complete all as specified and as directed.

Taking down Geysers and disconnecting water & electric connections, removing to store for keeping in safe custody for BER Board complete all as specified and as directed.

Taking down Ceiling fan/Exhaust fan, sealing cable end,dismantling blades and removing fan and blades to store for keeping in safe custody for BER Board complete all as specified and as directed.

Taking down sub main wiring /service cable including earth wire and removing from site to store for taking credit (Credit for above items should be made as per conditions seperately) and making good disturbed surfaces to match with the existing surfaces of walls, floors complete all as specified and as directed.

M & L for point wiring using proper colour coding complete all as specified with 1.5 sqmm PVC insulated FRLS-H unsheathed 1100 volts multistranded copper conductor two single core cable (Red and Black colour) confirming to IS 694:1990 Part-II with and including non metalic rigid PVC Conduit 25mm dia medium grade with all accessories including cutting chases pinning in, for concealed conduit wiring in wall/ceiling/floor/roof etc, making good of disturbed surface not exc 15cm girth, modular sunk pressed steel terminal box not less than 2mm thick, 50mm deep, covered with frame plate with cover for 01 to 16ways suitable for modular fittings including 1.5 sqmm PVC insulated FRLS-H unsheathed 1100 volts multistranded copper conductor one single core cable (Green colour) confirming to IS 694:1990 Part-II as continuous earth wire connected to common earth dolly all as specified and as directed for the following:- (a) One light/fan/exhaust fan/bell point controlled by one modular switch/bell push.

(b) -Ditto- all as per above Sch "A" Item No. 202.00 but one 3 pin modular socket outlet 5 Amp on the same board with other switch.

(c) -Ditto- all as per above Sch "A" Item No. 202.00 but one 3 pin modular socket outlet 5 Amp independent board.

(d) -Ditto- all as per above Sch "A" Item No. 202.00 but one light point controlled by two, 2-way modular switch.

(e) -Ditto- all as per above Sch "A" Item No. 202.00 but one 3 pin socket outlet 15 Amp independent board with 2.5 sqmm PVC insulated FRLS-H unsheathed 1100 volts multistranded copper conductor single core cable (Red, Black and green colour) confirming to IS 694:1990 Part-II.

M & L for modular switch, 1 way 6 Amp, 1 module

M & L for modular switch, 2 way 6 Amp, 1 module

M & L for modular switch, 1 way 16 Amp, 1 module

M & L for modular bell switch 6Amp, 1 module

S & F for modular socket 6Amp, 2/3 pin, combined 2 module.

S & F for modular socket 6A/16A, 2/3 pin combined 2 module.

M & L for buzzer, ding dong, AC, 230V single pole.

S & F for modular stepped type fan regulator, 50Watts - 2 module suitable for BLDC fan.

S & F for ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body of size.

S & F for Lamp holder (Batten/Angle) PVC/Polycarbonate type with back plate for batten/angle fittings, complete all as specified and directed.

S & F for Lamp LED 1 x 9 Watts, CDL, 3 Star rating, heat sink white with Polycarbonate diffuser, B-22 base cap, retrofit type, 220/230 volts, complete all as specified and directed.

Supply and fixing for LED lights fitting 1x 20 Watts (T-8), 4 feet long, 220V, AC, decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, prewired complete with two Nos of PVC box of size 75x75x20mm for mounting light fittings, complete all as specified and as directed.

Supply and fixing for LED light fitting 1 x 10 Watts (T-8), Mirror type with high out put diffuser 2 feet long, 220 Volts, AC decorative type with driver holder and LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, prewired complete with two Nos of PVC box of size 75x75x20mm for mounting light fittings, complete all as specified and as directed.

S & F for LED light fitting 1x9W/1X10W Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size with LED Lamp 1 X 9/10watts, complete all as specified and as directed.

Supply and fixing for Decorative wall light fixture made up of Polycarbonate, suitable for 1 x 9 Watts, retrofit LED lamp, B22 base, CITY-2, 220 Volts, AC, complete all as specified and as directed.

Supply and fixing for Round shape 1 x 15 watt 220 volts AC recessed/Surfaced type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed.

Supply and fixing for Post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing for LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including connecting up with three core flexible copper conductor cable of suitable size & IP 65/66 protection, complete all as specified and as directed.

S & F for GI Bracket made out from GI pipe 25/32mm dia bend to shape as required, 1.2Mtr long fixed on wall with flat iron clamps of size 25 x 4mm - 2 Nos with the help of bolts, nuts, washers etc for fixing of security light fitting, complete all as specified and as directed.

M & L for Rigid non-metallic PVC conduit 25mm dia (ISI Marks) inclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc for laying telephone & TV cable connections, complete all as specified and as directed.

M & L for sub main wiring with Four run of single core PVC insulated unsheathed FRLS copper conductor cable 1100 volt grade multistandard of size 10.0 sqmm (Red, blue, yellow and Black colour) and incl drawn through Rigid non-metallic PVC conduit not less than 25mm dia (ISI Marks) including accesssories, one run of single core PVC insulated unsheathed FRLS copper conductor cable 1100 volt grade multistandard of size 10.0 sqmm (green colour) for earth continuity wire and connected of common earth dolly complete all as specified and as directed. Note:- One run of Rigid non-metallic PVC conduit not less than 25mm dia, five run of 10.0 sq mm copper conductor cable is measured as one unit.

M & L for sub main wiring with two run of single core PVC insulated unsheathed FRLS copper conductor cable 1100 volt grade multistandard of size 4.0 sqmm (Red, blue, yellow and Black colour) and incl drawn through Rigid non-metallic PVC conduit not less than 25mm dia (ISI Marks) including accesssories, one run of single core PVC insulated unsheathed FRLS copper conductor cable 1100 volt grade multistandard of size 4.0 sqmm (green colour) for earth continuity wire and connected of common earth dolly complete all as specified and as directed. Note:- One run of Rigid non-metallic PVC conduit not less than 25mm dia, three run of 4.0 sq mm copper conductor cable is measured as one unit.

M & L for sub main wiring with two run of single core PVC insulated unsheathed FRLS copper conductor cable 1100 volt grade multistandard of size 6.0 sqmm (Red, blue, yellow and Black colour) and incl drawn through Rigid non-metallic PVC conduit not less than 25mm dia (ISI Marks) including accesssories, one run of single core PVC insulated unsheathed FRLS copper conductor cable 1100 volt grade multistandard of size 6.0 sqmm (green colour) for earth continuity wire and connected of common earth dolly complete all as specified and as directed. Note:- One run of Rigid non-metallic PVC conduit not less than 25mm dia, three run of 6.0 sq mm copper conductor cable is measured as one unit.

Supply and fixing for Ceiling fan 1200mm sweep, complete with blades, down rods and accessories, 230 V, Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including connecting up with three core flexible copper conductor cable for suitable size, complete all as specified and as directed.

Supply and fixing for Heavy duty Exhaust fan 300mm sweep, made of metal body complete with louvers shutter, voltage 230V, 50 Hz, 1200 RPM, Copper winding including connecting up with three core flexible copper conductor cable for suitable size and wall mounting fastener bolt, nuts & washers etc, complete all as specified and as directed.

Supply and fix for Water heater storage type, electric,capacity 25 litres.BEE 5 star rated, voltage 230V, 50 Hz, Copper tank including connecting up with three core flexible copper conductor cable for suitable size and wall mounting fastener bolt, nuts & washers etc, complete all as specified and as directed.

Supply and fixing for Ventilation/exhaust fan 250mm sweep, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, 1200 RPM, Copper winding including connecting up with three core flexible copper conductor cable for suitable size and wall mounting fastener bolt, nuts & washers etc, complete all as specified and as directed.

Fixing only and connecting electric/electronic meters upto 25/63 amps with wooden board including making connection suitable size copper conductor cable and testing complete all as specified and as directed.

S & F in Sheet metal enclosure 20Amp SP (2P+E) with Metal plug and socket DBs suitable for protection of appliances like AC/Geysers etc complete with one MCB single pole 20Amps, 240Volts including connection, testing and making good the disturbed surfaces, complete all as specified and as directed.

S & F for sheet metal enclosures MCB SPN DBs 12 Way, 240 Volts, 50Hz, AC, double door (12) suitable for flush mounting and surface mounting, conforming to IP 43 - IK 09 with acrylic door with 200 Amp copper bus bar for phase, complete with din rail, Neutral and Earthing bar, including connection, testing and making good the disturbed surfaces complete all as specified and as directed.

S & F for sheet metal enclosures MCB SPN DBs 8 Way, 240 Volts, 50Hz, AC, double door (12) suitable for flush mounting and surface mounting, conforming to IP 43 - IK 09 with acrylic door with 200 Amp copper bus bar for phase, complete with din rail, Neutral and Earthing bar, including connection, testing and making good the disturbed surfaces complete all as specified and as directed.

S & F for replacement of sheet metal enclosures MCB TPN DBs 6 Way, 415 Volts, 50Hz, AC, double door (18) suitable for flush mounting and surface mounting, conforming to IP 43 - IK 09 with acrylic door with 200 Amp copper bus bar for phase, complete with din rail, Neutral and Earthing bar, including connection, testing and making good the disturbed surfaces complete all as specified and as directed.

S & F for replacement of miniature circuit breaker (MCB), Triple Pole & Neutral 40 to 100 Amp, rating 415V, 10 KA current carrying capacity, 'B' curve fixing in the MCB DB complete with connection testing and commissioning, complete all as specified and as directed.

S & F for miniature circuit breaker (MCB), Single Pole & Neutral 40 to 63 Amp, rating 240V, 10 KA current carrying capacity, 'C' curve fixing in the MCB DB complete with connection testing and commissioning, complete all as specified and as directed.

S & F for miniature circuit breaker (MCB), Single Pole 6 to 32 Amp, rating 240V, 10 KA current carrying capacity, 'B' curve fixing in the MCB DB complete with connection testing and commissioning, complete all as specified and as directed.

Supply and Fixing of Kitchnen Chimney of Size 120 cm with 1626 m3/ hr suction, smart on & intelli Auto Clean silent kitchen chimney with filterless technology and as directed by Engr-in-Charge.

Taking down old service connection/UG Cable removing of site complete all as directed.

Supply and laying with commissioning and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of size 16 sqmm x 2 core laid in trenches, passing through pipes, fixed on walls complete including connecting properly by means of thimbles etc, complete all as specified and as directed.

Supply and laying with commissioning and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade of size 35 sqmm x 3.5 core laid in trenches, passing through pipes, fixed on walls complete including connecting properly by means of thimbles etc, complete all as specified and as directed.

Excavating in trenches, not exc 1.5 m wide and not exc 1.5 m in depth for laying of electric cables or water pipe etc, not exc 10 sqmm on plan and not exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge. Note : Rates includes removing of paver blocks carefully and stack properly for refixing after laying of cables .

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting pointcomplete all as specified.

Material and labour for river washed and screened, dry sand for cushioning of cable in trenches for cable protection including spreading, leveling and hand punning complete all as specified in SSR Part-I and as directed. Note :- Only compacted thickness of sand will be measured and paid separately.

S & F machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 100 mm thickness M-50 Grade not less than 0.45 mtr wide for repairing road cut/footpath carried out under Sch "A" srl item No.1.00 & 2.00

Removing and Re-laying for machine pressed precast concrete interlocking paver block any shape and size for repairing road cut/footpath carried out under Sch "A" srl item No.1.00 & 2.00

Supply, laying un-reinforced precast concrete cable cover class LV type 1 flat size 250mm x 150 mmx 40 mm.

Material and labour for Horizontal directional drilling (HDD) is a streeable trenchless method of Laying (installing) underground cables in a shallow arc along a 40mm/50mm bore path by using a surface-launched drilling rig, with minimal impact on the sorrounding area complete all as specified and as directed by Engr-in-charge.

M&L for GI pipe ,light grade 40mm dia for road crossing of cable for cable protection laid in trenches or above ground surface, complete all as specified and directed.

M&L for Earthing complete with galvanized iron earth plate electrode 600 x600x6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.6 meter below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts check nuts galvanized iron or steel all as shown in Electrical plate No. 3 of SSR PT- I testing on completion with & incl. 15 mm bore light grade GI protection pipe 7.5 mtr long for earth lead, PCC (1:3:6) pit with pre cast RCC (1:2:4) type B1 cover slab with one handle made out of 8mm dia round bar, watering arrangement with funnel, wire mesh 20 mm bore light grade GI pipe, common salt & charcoal alternative layers, necessary excavation earth work, including earthing test point all as specified or indicated including testing on completion and as directed.

Supply, laying, conecting and testing of ISI marked GI steel water tubing medium grade Including S & F all fittings and fixed complete to walls and celling or laid in floors complete of following sizes :-

(a) 50 mm bore

(b) 40 mm bore

(c) 25 mm bore

S & F 25 mm bore Gun metal globe valve or gate valve with iron wheel head , screwed both ends with 01 No union for iron pipe heavy duty with ISI marked all as specified and directed.

S & F 50mm bore Gun metal globe valve or gate valve with iron wheel head, screwed both ends with 01 No Union for iron pipe heavy duty with ISI marked all as specified and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting pointcomplete all as specified.

BHARAT ELECTRICAL TRADERS (BID ID -3308724)

A K BANDHUS (BID ID -3308567)

m/s gupta construction (BID ID -3307399)

m/s meetu enterprises (BID ID -3307503)

M/S SURAT SINGH AND SONS (BID ID -3308137)

M/s Arihant Builders (BID ID -3308370)