Learning Resource Center

Amount

Civil Work

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.: All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying 230mm thick dry rubble soiling using locally available approved quality stones, hand laid, well rammed, watered and consolidated, including filling the gaps/interstices/voids using quarry spalls and/or hand broken metal or shingle and blinding the same with stone grit murum, etc., compaction with mechanical/vibratory roller etc. complete as directed by the Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. a) Concrete of M25 grade with minimum cement content of 330 kg /cum : All works upto plinth level

b) Concrete of M25 grade with minimum cement content of 330 kg /cum: All works above plinth level to all floor level : superstructure

c) Concrete of M35 grade with minimum cement content of 370 kg /cum : All works above plinth level to all floor level : superstructure

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. all level, all floor. Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral-staircases

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Monostrand Unbonded Tendons (ACI 423.6-01, PTI approved): Supply, Installation, Testing, Commissioning & election of Monostrand Unbonded Tendons as per approved make, shop drawing & approve sample by Architect / Client. work complete including all type of scaffolding, loading, unloading, transportation, fittings, fixtures, all type of safety measures, equipment, crane, at all floor, all levels etc. complete as per shop drawings and specifications. Sample mock & Shop drawing shall be approved from Architect/Client. No extra charges will be paid for any scaffolding required for installation of PT beam works. As per attached technical specification data sheet in tender documents. Monostrand Unbonded Tendons: Prestressing Steel: (1). Low-Relaxation 7 wire Strand of Class II (Grade 270) with 12.7 mm diameter shall confirm to the requirements of IS 14268: 1995, (2). Sectional steel area of Strand: 98.7 mm2, (3). Modulus of Elasticity: At least 196,500 N/mm2, (4). Weight of Strand: More than 0.775 kg/m, (5). Yield Load: Not less than 180 kN, (6). Ultimate Strength: Not less than 1860 N/mm2, (7). Minimum Breaking Strength: Not less than 183.7 kN, (8). Minimum elongation: 3.5% for gage length of 600 mm, (9). Relaxation at 1000 hours: Less than 2.5% @ 70% Minimum Ultimate Tensile Strength, Sheathing Specifications: (1). Sheathing material: polyethylene or polypropylene, (2). Minimum Thickness: 1.27 mm, (3). Inside diameter: At least 0.76 mm greater than the maximum diameter of the strand., (4). Minimum Density: 0.941 gram/cm3, Grease Coating Specifications: (1). Protect against corrosion to the unbonded strand, (2). Provide continuous non-brittle coating., (3). Resist flow within temperature range., (4). Non reactive with Prestressing steel, reinforcing steel concrete., (5). Minimum weight of the grease coating on the Prestressing strand shall not be less than 1.14 kg per 30.5 m for 12.7 mm diameter strand., (6). Grease coating shall extend over the entire tendon length, Encapsulated Mono block (Anchor plate) Ref.: ACI423.6: Chemical Composition: (1). Carbon: 3.15‐4.15%, (2). Silicon: 1.9‐3.0%, (3). Phosphorus: 0.005‐0.035%, (4). Magnesium: 0.056% max, (5). Manganese: 0.1‐1.0%, (6). Sulphur: 0.005‐0.035%, Mechanical Properties: (1). Elongation (%): 6 to 9, (2). Hardness Number (BHN): 180-240, Material Grade: (1). ASTM A 536 Grade 80‐55‐06, Other properties: (1). Graphite Type (As per ASTM A247 Plate I & III), (2). Form I & II (Spheroid or Nodular type), (3). Distribution A (Uniform Distribution), (4). Pearlite: 55‐60%, (5). Carbide: Less than 3%, (6). Nodularity: 90‐95% Standard Specification for Wedges (Ref.:ACI423.6): Chemical Composition: (1). Carbon: 0.18‐0.24%, (2). Titanium: 0.001‐0.05%, (3). Molybdenum: 0.008-0.02%, (4). Silicon: 0.23‐0.30%, (5). Manganese: 0.85‐1.24%, (6). Nickel: 0.01‐0.06%, (7). Chromium: 0.9‐1.13%, (8). Copper: 0.01‐0.23%, (9). Phosphors: 0.005-0.035%, (10). Sulphur: 0.005‐0.035%, Hardness: (1). 56‐65 HRC at Surface, (2). 50‐58 HRC at Core, Material Grade: (1). 20MnCr5 or 20CrMnTiH,

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level to all floor level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level to all floor level : Cement mortar 1:4 (1 cement :4 coarse sand)

CEMENT PLASTER (IN COARSE SAND): Providing and laying plaster in all floor, all height, all level : 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT: 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand). Incl. all floor, all height, all level etc. complete

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge. Including grooves finish, all floor, all height, all level etc. complete

Extra for providing and mixing water proofing material in cement per bag of plaster work in proportion recommended by the manufacturers.

Interior Paint : Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. including, scaffolding, accessories, all height, all floor, all level etc. complete. Two coats

Wall Primer: Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. including, scaffolding, accessories, all height, all floor, all level etc. complete.

Putty: Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. including, scaffolding, accessories, all height, all floor, all level etc. complete.

Exterior Paint: Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). including, scaffolding, accessories, all height, all floor, all level etc. complete.

Exterior Paint: Finishing walls with textured exterior paint of exposed RCC look or required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm. including, scaffolding, accessories, all height, all floor, all level etc. complete.

Texture Paint : Exposed RCC Concrete Work (6mm Groov Light tone & Top coat Dark tone): Supply & Application of Luxture’s Exposed RCC Concrete Facades as per drawing.. Base Coat with Crack Filling, Two Coat top coat and Two coat TC 5000. a. Preparation of surface: Make sure the surface should be free from oil, grease and all type of foreign items. Minor repairs should be make up with cement; sand mixture. Other than concrete plasters, other suitable surfaces are ply board, asbestos sheets and gyp board partitions, and all type of absorbent surfaces. b. Base coat*: - Apply 2 coats of LCF- Base Coat with fiber glass mesh an average thickness of 1.5-1.7mm. LCF Base Coat is a polymer modified ceramic based material bonded primarily with in-organic binders. LCF Base Coat is a dry material and water should be added in to this to make it workable. c. Grooving and Taping: - The dried base coat should be properly grooved or tapped as per the designs suggested by the engineers. d. Top Coat: - Apply the LCF- Top Coat of desired color with an average thickness of 1.7-2mm. LCF- Top Coat is a polymer modified ceramic based material with special high performance additives, in-organic binders are the primery binding medium. LCF- Top Coat is a dry material and water should be added in to it to make it workable. LCF- Top Coat can be applied in desired pattern like honey combed (to be done with special tools), trowel marked, rough cast or in smooth. e. Protective Sealer: - LCF- Top Coat when gets dry, apply two coats of TC-5000 (exterior grade protective sealer). TC-5000 protects the surface from dust, dirt, fungus and stains. Work complete including all type of material, labour, scaffolding, finish, loading , unloading, safety measures, transportation, all leads ,accessories, sample mockup, all floor, all levels, all heights etc complete as per detailed drawings, specifications & instruction of Client/EIC. sample mock shall be approved from Architect/Client.

Supplying, diluting & Injecting chemical emulsion for Pre constructional Anti Termite Treatment With Chlorpyriphos/Lindane E.C. 20% with 1% concentration in 3 stages creating a continuous chemical barrier all-round the building including diluting in water as per manufacturer's specification conforming to IS 6313: 1981 in under & all around raft slab, beam, footings, column pits, trenches, wall trenches, backfill, plinth filling, junction of wall and floor, external perimeter of building, surrounding of pipes, over the top surface of the consolidated earth etc. for all lead and lift.. The treatment shall be carried out by specialized agency specified by the Client/ Consultant. Plinth area at ground level excluding open courts shall be measured. Treatment of soil under floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos E.C. 20% with 1% concentration

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge: With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Light Weight Filling in the Sunken Portion: Providing and filling the cavity of sunken portion of toilets (after application of principal waterproofing treatment to surface of sunk RCC slab) with broken AAC blocks of 25 mm to 115 mm in size with 50% of cement mortar 1:4 conforming to IS : 2645 complet as directed by the Engineer-in-charge.

Waterproofing work at Edge Pool : Surface Preparation: Minor cleaning work, removal of loose concrete and filling cracks with polymer modified mortar using Dr. Fixit Pidicrete URP. Making of angle fillets all around the periphery of the wall with polymer modified mortar using Dr. Fixit Pidicrete URP in the ratio of 1 Pbw polymer : 10 Pbw cement :30 Pwb quartz sand .Providing & Applying Dr.Fixit FastFlex, 2 component polymer modified flexible and highly elastic cementitious coating composed of high quality cement and graded fillers, additives and acrylic polymer. Tough film built up provides excellent water proofing. Highly elastic film formation which accomodates thermal movements withstand 5.0 bar hydrostatic pressure without any leakages,Excellent adhesion to concrete and masonry substrates,form seamless coating without any joints,brush/roller applied water proof coating, non toxic ,food grade CFTRI certified with low VOC content, having tensile strength of 5 N/MM2, Adhesion strength of 0.8N/mm2,crack bridging ability upto 2mm and with more than 120% elongation, applied in 2 coats in the form of slurry at total consumption of 1.5kg/sqm to be applied by brush/roller over the vertical surface of the balcony walls/upstand beam,upbound suface areas upto 300mm above FFL etc complete in all aspects as directed by Engineer/Architect. Protective plaster/base coat- Providing & Applying 12-15mm thick Protective Screed / Plaster in cement mortar of 1:4 including Proofsol LWP integral waterproofing admixture @ 100 ml per bag of cement with wattas at the junctions applied on the floor & treated vertical surfaces, broom finished/ smooth finished as directed at site, including curing & testing for watertightness for 7 days etc.complete in all aspects as directed by Engineer/Architect. The area of the floor and sides of sunken portion treated shall be considered for payment purpose. including Micro-concrete using pipe packing,

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish, Size of Tile 600 x 600 mm (Toilet area flooring) Equivalent to SUNHEART ENRICH GREY (MATT) SIZE : 600 x 600

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in dedo, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x1200 mm (Toilet area dedo and skirting) Equivalent to SUNHEART KEEN BLANCO(GLOSSY) SIZE : 600 x 1200

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and mirror polishing complete with base of cementmortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and mirror polishing , antiskid groove complete.

Providing and laying Yellow colour Kota stone slab for flooring work in patterns over 20 mm. (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and jointed with grey cement slurry including, joints with ready mix grout, exposed mirror polish sides, rubbing, cleaning and covering till the hand over. directed by Authority. 25mm Thk.kota stone

Providing and laying LEATHER FINISH machine cut Kota stone slab for flooring, tread, risers of steps, skirting, dado and pillars in patterns over 20 mm. (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) and 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) for skirting and jointed with grey cement slurry including nosing, chamfered front edges, fixing, antiskid groov, joints with ready mix grout, epoxy grouting, adhesives, chemical, polish, rubbing, cleaning and covering till the hand over. directed by EIC/Architect. 25mm Thk. Kota stone

Artificial stone work in wall : Providing and laying Polished Granite stone slabs 18 mm thick in risers of steps, skirting, dado, cladding and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Equivalent to Motto Saga SNP Verde Grey Finish- Glossy

Artificial stone Door Frame: Providing and fixing 15 mm thick one-piece Artificial stone as per approved shade in door jambs lining for door frames for fixing door shutters in two overlapping bands to give an over all width not less than 280mm with cement mortar 1:3 and neat cement float in proper line, level and plumb ,filling the joints in matching colour pigment to match the stone shade, supports, scaffolding and moulding etc complete in all aspects as per drawing and directed by Architect/ Engineer. No Overlapping will be paid for measurement. Basic rate of Artificial stone : Rs. 150/ Sq.ft

Artificial Stone window sill : Providing and fixing 15 mm thick one-piece Artificial stone as per approved sample for window sills, jambs and soffits (surrounds on all 4 sides of the opening) as per detail drawings including two overlapping bands, moulding, chamfer with polishing in cement mortar 1:3 (1 cement : 3 Coarse sand) of 12mm thickness/ suitable adhesives/ proper clamping and neat cement floating to proper line, level and plumb, filling the joints with white cement including approved pigment to match the colour of granite slab, cleaning, curing, scaffolding etc. complete in all aspects and as directed by Architect/Engineer. Basic rate of Artificial stone: Rs. 150/ Sq.ft

Glass mosaic at Edge Pool : Providing and fixing Glass mossaic tiles on finished plain wall surface of size 25 mm x 25 mm x 5 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge, including adheshive chemical, epoxy, grout, joint fiiller etc. Rate shall be inclusive of all material loading unloading at all height and all floor. Sample mock shall be approved from Architect/Client. Equivalent to Veneto Mosaic Code : 561(20.00) + 562(20.00) + 564(10.00)+566(20.00) + 567(20.00) + 569(10.00), Mosaic size: 2.5x2.5cm, Thickness: 5 mm, Sheet Size: 30x30cm, Joint Gap:1.6 mm.

Artificial stone Basin Counter 600 wide: Providing & fixing two layers of wash basin counter, first layer (top layer) using approved shade and sample of 15 mm thick artificial stone and second layer (base layer) using 25mm thick Kotastone of approved shade, joined together with 1:4 Cement mortar bedding / approved tile adhesive, to true plane & level or to slopes, or close jointed with cement slurry with pigment of matching shade and colour and finishing with the same, including dedo 6", cutting stone as per required shape & size to fit Wash basin & 4" facia with moulding, nosing, chamfered front edges, fixing, disposal of debris etc. finished as per design in detail drawing and instruction of Architect/EIC. sample mock shall be approved from Architect/EIC. The granite shall be fixed at end of counters where counter is not resting on wall supoort. The edges of end support, fascia patti etc shall be moulded, polished as directed and complete in all aspects as per detail drawings. Centre line length of the counter shall be measured for payment purpose. Basic rate of stone is Rs.150 / Sq.ft

Granite Pantry Platform 600 wide: Providing & fixing in position Kitchen platform with mimum 600mm width made as under: Vertical supports: Made out of 18 mm thick white marble slabs sandwich supports (two slabs joined together using Araldite adhessive to full surfae area) placed at specified spacing as per detailed drawing and suitable to house modular kitchen under the counter Trolleys. Rate includes providing vertical garnite band to vertical supports with moulded/polished edges. Kitchen Counter Top : Finished with 18+/-2mm approved first qulaity, Colour, shade and textutre mirror polished classic grey Granite slab (minimum length of slab shall not be less than 1.80 Meter for Kitchen counter etc.) resting on 18mm thick white marble base support slab (in one piece) and fixed with CM 1:2 or approved tile adhessive as directed at site. Front Facia: 50 to 75mm wide Granite band in one piece not less than 1.80 RM in length for kitchen counter with mirror polish champhered edges complete as per Architectural working drawing.Making hole/sleeves for Gas pipe as per drawing. Rate should include chasing walls, floors to embed vertical supports and counter top using CM 1:2 including making cutout for for kitchen sink, core cutting for pillar cock, bottle trap etc. complete as per directions & instructions of the Architect. Basic rate of stone is Rs.150 / Sq.ft

Double Leaf Alluminium heavy duty frame glass door: Providing & Fixing of Alluminium heavy duty frame glass door comprising from 12 mm thick toughened glass door with necessary ss 304 grade hardware & accessories complete as per approved make & sample by DTA. work complete including all type of hardware, fittings, fixtures as per instruction of Authority/ DTA etc complete as per detailed drawings and specifications. sample mock shall be approved from DTA/Authority. Hardware: Hafele/Dorma/Geze as per approved make by architect. FS 2104 Double Action Floor Spring with 90° Hold Open and SS Cover plate, Size 4 (Without accessories), Max. door leaf weight 120kg ,SS Matt,For door Double Action accessories for Floor Spring suitable for Timber doors Narrow Dead Lock BS 30mm C/C 92mm 24mm Forend SS 304 SSM Euro Profile Double Cylinder 40+40 = 80mm Brass SN EPC Escutcheon Oval SS 304 SSM Long Handle : 1200 mm Height FLush Bolt for Metal Door 304mm SS 304 SSM Flush Bolt for Metal Door 600mm SS 304 SSM Dust Proof Strike SS 304 NM Floor Mounted Door Stopper Half Round SS 304 SSM

Single Leaf Flush Door finish with laminate: Providing and fixing in position 40 mm thick BWP grade single leaf flush doors of approved make and finished with both side 1 mm thick VNR laminate as approved sample, Hardware system as per approved make & Sample (Hinges, Mortise lock with 3 pair key, Door stopper, door closer ). Door closer and mortise lock of Dorma/Geze/Haffle as per approved make by Architect. Hinges, Door stopper and other accessories of Kich/Ozone/Inox as per approved make by architect. work complete including all type of hardware, fittings , fixtures as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client. Equivalent to VNR Series Laminate.

Single Leaf Flush Door finish with laminate (Toilet door): Providing and fixing in position 40 mm thick BWP grade single leaf flush doors of approved make and finished with both side 1 mm thick VNR laminate as approved sample, Hardware system as per approved make & Sample (Hinges, Mortise lock, Door stopper, door closer ). Door closer and mortise lock of Dorma/Geze/Haffle as per approved make by Architect. Hinges, Door stopper and other accessories of Kich/Ozone/Inox as per approved make by architect. work complete including all type of hardware, fittings , fixtures as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client. Equivalent to VNR Series Laminate.

Handicap Toilet Door : Providing and fixing in position 40 mm thick BWP grade single leaf flush doors of approved make and finished with both side 1 mm thick VNR laminate as approved sample, Hardware system as per approved make & Sample (Hinges, Mortise lock , Horizontal grab bar, Door stopper, door closer). Door closer and mortise lock of Dorma/Geze/Haffle as per approved make by Architect. Hinges, Door stopper and other accessories of Kich/Ozone/Inox as per approved make by architect. work complete including all type of hardware, fittings , fixtures as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client. Equivalent to VNR Series Laminate.

WPC board shutter with laminate finish (Duct area): Providing and fixing in position 12 mm thick WPC shutter & partition of approved make with VNR laminate finish as approved, shutter fixed with floor and above pivot of approved make, pivot cover plate, safety measures , lock & handle etc fixtures of approved make list with all necessary fittings etc. aluminium frame as per required size Complete as per detailed drawings and specifications.

Sliding window : (Domal series) Supply & Fixing of Aluminium sliding window with powder coated as per by approved make & sample by architect/EIC. frame section: 101.5 x 47.5 x 1.5 mm Shutter section : 27 x 65 x 1.54 mm Glass : 5 mm thick reflective glass of saint gobain or approved make list including concealed lock, albose , other necessary fixtures and fastening , PVDF rollers , EPDN gasket, silicon sealent etc. complete as per detailed drawings, mock sample and specifications.

Ventilation with provision of Exhaust fan : Supply & Fixing of Ventilation with exhaust fan with powder coated as per by approved make & sample by architect/EIC. frame section: 45 x 45x 1.5 mm Glass : 5 mm thick Forsted toughened glass of saint gobain or approved make list including necessary fixtures and fastening , EPDN gasket, silicon sealent etc. complete as per detailed drawings, mock sample and specifications.

Mosquito Jali : Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm With 12 mm mild steel U beading all complete.

MS Fabricated Door: Providing Fabrication & erection 3 mm thick M.S. sheet/plate door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces. including CNC cutting/Engraving as per reference image given by Architect. The work includig necessary fabrication work, fittings, fixtures, accessories, pivot, door, handle, lock etc complete. finish with Anti corrosive paint with primer as per approved shade by Architect. The scope includes loading, transportation, unloading and delivery and erection site of all fabricated structures, alignment and welding of all structures true to line, level, plumb and dimension. sample mock shall be approved from Architect/EIC. Shop drawing shall be provided by Contractor.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved anticorrosive paint all complete. Fixed to steel windows by welding

Flush Valve : Providing and fixing Meropole Flush valve of as per approved make list . Work complete including all type of finishing. Model Equivalent to Jaquar FLV-CHR-1093N

Health faucet: Providing and fixing 8mm dia. Health faucet as per approved make list with flexible pipe of 1.2mt. length and holding stands complete. Work complete including all type of finishing. Model Equivalent to Jaquar ALD-CHR-573

Wash Basin : Providing and fixing under counter Wash Basin including fittings and waste coupling and fixing on wash basin counter by tile adhesive of approved make. Work complete including all type of finishing. Model Equivalent to Jaquar FNSWHT- 40701 + ALD-CHR-705

Providing and fixing 15mm dia. Angular Stop Cock with flange as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar EKO-CHR-33053

Providing and fixing Pillar cock as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar PRS- CHR-043

Urinal : Providing and fixing Urinal with flush valve with wall flange as per approved make list , with necessary coupling of approved make for wash basin & sink. Work complete including all type of finishing. Model Equivalent to Jaquar URS- WHT-13253N + PRS-CHR-073

Urinal partition: Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Nirali : Grace Plain- 510MM X 432MM

Providing and fixing Sink Cock with regular spout with wall flange as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar FLR-CHR-5347N

Providing and fixing CP Brass 32mm size Bottle trap with 300mm & 190mm long wall connection pipes & wall flange of approved quality & make and as per the direction of Engineer-in-charge. with necessary coupling for wash basin & sink. Model equivalent to Jaquar ALDCHR-773M L300X190

Soap Dispensor : Providing and fixing liquid soap Dispensor of best quality. Complete as per directed by architect and engineer in charge. Euronics code Manual Soap Dispenser (1000ml) ES43

Hand Dryer: Providing and Fixing Electrical hand dryer, fully automatic type , cover shall be fabricated in ABS material finished, the unit shall deliver of hot air and electrical rating shall be 240 V / 1 phase / 50 cycles. Complete as per directed by architect and engineer in charge. Euronics code : Euronics of EH270N

Providing and fixing of Washroom Panel/Recessed/S.Steel (2in1,Paper Dispenser / Waste Receptacle) - Mini, Model no KPD3S of Euronics or approved make list . Work complete including all type of fittings, fixtures, tools, etc complete as per manufacturer specification and drawing.

Providing and fixing of Sanitary Napkin Hygiene Panel (3in1) - For Feminine Washroom : Model no ESN03S of Euronics or approved make list . Work complete including all type of fittings, fixtures, tools, etc complete as per manufacturer specification and drawing.

Providing and fixing Grab bar vartical swing as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar WAC-SAPBG0800CS

Providing and fixing Grab bar 692mm long as per approved make list and work complete including all type of accessories . Model equivalent to Jaquar WAC-SAPBR0600CS

Providing and fixing 6 mm thick mirror of Saint Gobain/ Modiguard / Asahi as per approved make shall be fixed with profile frame section (Silver/gray/black etc.). Provision shall be made for conceal led light work as per detailed drawing / instruction of architect complete. Rate shall be inclusive of frosting work as per detail drawing.

Toilet Cubical : Model Type: Greenlam Sturdo Essentia Seren : Thickness of Compact Laminate : 12mm Nos 1 32075 32075 . Door : 600mm*1785mm , Divider Height : 1820mm, Overall height : 1995mm (Including 150mm Ground clearance) Supply & Installation of Toilet Cubicles as per approved make & sample by DTA . 12 mm Compact Grade 1.5 mm thick laminateBoard of the approved shade by DTA . Accessories for cubicles.1. Aluminum “U” Section with a) Aluminum U Channel b) Nylon Gravity hinges c) Nylon Coat Hook d) Nylon Adjustable Leg e) Nylon Door Knob f) Nylon Thumb Turm Indicator g) Aluminium Door Stopper Channel h) Aluminium Top Rail e) Screws, Wall Plugs & Noise Tape Etc. Work complete including all type of fittings, fixtures, tools, etc complete as per manufacturer specification and drawing.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet: Sand cast iron S&S as per IS: 3989

Single Glaze Unit (SGU): Design, Fabrication, Supply, Installation & Handover of Single glass glazing system. Semi-unitized glass glazing Auminium (sash frame) fix Glass section Jindal make or equivalent curtain section No. 22736 size 81.16mm x 50mm x 2mm weight 1.615 kg/mtr. Section No. 22738 size 81.16 x 38.5 x 2mm weight 1.294 kg/mtr. Shash frame section No. 35800 size 37.1mm x27.5mm x 1.4mm weight 0.548 kg/mtr. Patti for shash frame 29.2mm x 7.95mm x 2 mm , Akzonobel powder coated Aluminium section code SP338N with 50 micron. 6mm ET -125 HS Glass make Saint Gobain. 2mm thick x 12mm Brode 3M VHB Tape for stick glass, glass to metal structural sealent silicon & weather sealent silicon for groove, EPDM Gasket, m.s. bracket zinc coated, other necessary fixtures & fastening as per drawing specification. Work complete including all type of hardware, fittings , fixtures as per instruction of Client/Archtect etc. Rate shall include fixing of the main frames to RCC/Steel Structure with necessary clamps, fastening straps, nuts, bolts, rivets, washers and other fastening materials shall be in stainless steel grade 316. Rate shall include EPDM / Neoprene barrier, approved silicon sealant of recommended grade from DOW corning. complete for a full proof system.b) The floor closure shall be provided continueously at all level with 2mm thk Aluminium Flashing closing Gap between transome and building line.The fire stop for 2 hr rating with smoke seal (intumescent ‐3M )at all floor slab levels required with thermal insulation of 64 kg/m3 density Rockwool.c) Norton double sided adhesive tape shall be of Open cell type # V‐2100 of Grindwel Norton make. All the joints horizontal or vertical inside proper sealed with weather sealants (Non Stain & Non‐bleed) during the installation. Selant shall be Dow corning Structural sealant DC ‐995, Weather Silicon DC 789. Rate including all type of scaffolding, safety measures, form work at all floor, all levels etc. complete per detailed drawings and specifications, sample mock shall be approved from architect / client. Work complete including all type of hardware, fittings , fixtures as per instruction of Client/Archtect etc. Rate including all type of scaffolding, safety measures, form work at all floor, all levels etc. complete per detailed drawings and specifications, sample mock shall be approved from architect / client.

Double Glaze Unit ( DGU) : Design, Fabrication, Supply, Installation & Handover of Single glass glazing system. Semi-unitized glass glazing Auminium ( sash frame) fix Glass section Jindal make or equivalent curtain section No. 22736 size 81.16mm x 50mm x 2mm weight 1.615 kg/mtr. Section No. 22738 size 81.16 x 38.5 x 2mm weight 1.294 kg/mtr. Shash frame section No. 22840 size 68.1 X 28 X 15X 1.6MM weight 0.693 kg/mtr. , Akzonobel powder coated Aluminium section code SP338N with 50 micron. 6MM ET 125 HS+ 12 MM Air Gap +6MM Clear HS make Saint Gobain. 2mm thick x 122mm Brode 3M VHB Tape for stick glass, glass to metal structural sealent silicon & weather sealent silicon for groove, EPDM Gasket, m.s. bracket zinccoated, other necessary fixtures & fastening as per drawing specification. Rate shall include fixing of the main frames to RCC/Steel Structure with necessary clamps, fastening straps, nuts, bolts, rivets, washers and other fastening materials shall be in stainless steel grade 316. Rate shall include EPDM / Neoprene barrier, approved silicon sealant of recommended grade from DOW corning. complete for a full proof system.b) The floor closure shall be provided continueously at all level with 2mm thk Aluminium Flashing closing Gap between transome and building line.The fire stop for 2 hr rating with smoke seal (intumescent ‐3M )at all floor slab levels required with thermal insulation of 64 kg/m3 density Rockwool.c) Norton double sided adhesive tape shall be of Open cell type # V‐2100 of Grindwel Norton make. All the joints horizontal or vertical inside proper sealed with weather sealants (Non Stain & Non‐bleed) during the installation. Selant shall be Dow corning Structural sealant DC ‐995, Weather Silicon DC 789. Work complete including all type of hardware, fittings ,fixtures as per instruction of Client/Archtect etc. Rate including all type of scaffolding, safety measures, form work at all floor, all levels etc. complete per detailed drawings and specifications, sample mock shall be approved from architect / client.

Opening in Glazing : Extra for openable side / top hung vision glass panels including providing supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hingis, min 4-point cremne locking sets with stainless steel plates, handles , buffers etc. including necessary stainless steel screws / fasteners, nuts, bolt, washers, fafety measures etc. all compete as per the Architectural drawings, as per the approved drawings, as specified and as directed by the engineer in-charge. sample mock shall be approved architect/ EIC.

ACP Clading Type 1: Model Equivalent to Viva Composite Panel Lustre Series - VA 6001: Panel Thickness : 4MM, Coil Thickness : 0.25MM, Coating : PVDF/FEVE, : Designing, framing testing, installing and fixing in position Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 4mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, dowcorning weather silicone sealant (789), backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests aluminium composite panel cladding, cleaning and protection of the aluminium composite panel cladding till the handing over of the building for occupation. The Contractor shall provide aluminium composite panel cladding, having all the performance characteristics all complete, as per the drawings, as per item description, as specified, as per the approved shop drawings and as directed by the DTA /Engineer. However, for the purpose of payment, only the actual area on the external face ( L x d) of the Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. Base aluminium frame for ACP cladding is inclusive item as mentioned above. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles, scaffolding , adhesives consumable hardware & required accessories, grooves etc of approved make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill DTA's design intent. No additional claims will be entertained for this. Contactor shall provide stability certificate for the work. Rate inclusive of shop drawing.

ACP Clading Type 2: Model Equivalent to Viva Composite Panel Wooden Rustic - VA 582: Panel Thickness : 4MM, Coil Thickness : 0.25MM, Coating : PVDF/FEVE, : Designing, framing testing, installing and fixing in position Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 4mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, dowcorning weather silicone sealant (789), backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests aluminium composite panel cladding, cleaning and protection of the aluminium composite panel cladding till the handing over of the building for occupation. The Contractor shall provide aluminium composite panel cladding, having all the performance characteristics all complete, as per the drawings, as per item description, as specified, as per the approved shop drawings and as directed by the DTA /Engineer. However, for the purpose of payment, only the actual area on the external face ( L x d) of the Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. Base aluminium frame for ACP cladding is inclusive item as mentioned above. The rate shall be for complete item inclusive of all material, labour, wastages, necessary tools & tackles, scaffolding , adhesives consumable hardware & required accessories, grooves etc of approved make for all floors, all heights, all levels and all places within campus. Contractor shall do all the needful and shall fulfill DTA's design intent. No additional claims will be entertained for this. Contactor shall provide stability certificate for the work. Rate inclusive of shop drawing.

Aluminium Fins/Louvers (Elevation): Supplying and Installing of METALIUMTM make U- Shaped Baffle 50*50*50mm (50mm gap) Galvanized Steel 0.50mm TCT plain wooden powder coating on visible surface of Panel and supporting structure in black color Exterior Louver System. Panel (Galvanized Steel): Metalium make square edge P-50 series panels, 50 * 50 * 50 mm& 0.50 mm TCT Galvanized Steel. Panel length is up to approx. 3 mtr. Panels shall be wooden powder coated on visible surface with special Exterior Grade powder to enhance property of Fadedness Resistivity. P-50 Carrier (U Shaped): Black enameled Galvanized Steel Carrier of 20mm wide at bottom x 39mm deep x 0.6 mm thick in a standard length of 8’ with cutouts to hold the panel in a module of 100 mm centre to centre at a distance of 1 mtr. Carrier and suitable structure shall be powder / coil coated on exterior face to enhance properties of Fadedness and corrosion resistivity. Installation Details: GS Clit shall be fixed on vertical columns with dash fasteners at distance not more than 1 mtr. Centre to centre on which Tubular Stud sections will be laid with corrosion proof screws and on this rigid structure carrier shall be fixed vertically / horizontally at distance of 1 mtr. Centre to centre. Panel shall be clipped to carriers. Rate shall inclusive of mock up sample, all materials, loading, unloading, transportation, placing at all floors and for all leads, all accessorie , Scaffolding etc as described in item description. Work complete as per the detailed drawing , mockup sample and instruction of Architect/Client.

Elevation fins without light provision: Size : 57 x 200 mm Design, Fabrication, supply, installation of Aluminium vertical fin with cover section made out of 56.50 x 200 x 2 mm deep fixed to the Alum pressure plate section-53.43x11.30x2mm. The fin shall be made out of extruded Aluminium Alloy 6063- T5 grade & All the visible surfaces shall have Powder coating finish of 50-70 micron thickness as per approved shade by architect/client. Including all necessary hardware & Labour etc. All aluminium extrusions shall be of 6063 TS 6 alloy confirming to ASTN B 221 of Jindal / Gujarat Alluminium Extrusion as per approved make by Client /Architect.work complete including all type of fittings, fixtures, all type of safety measures, scaffolding, at all floor, all levels etc. complete as per shop drawings and specifications. sample mock & Shop drawing shall be approved from Architect/ Client.

Signages-1 : Led Channel Letters: Main Building Terrace: Learning Resource Center: Supply and installation of 3 inch embozz Stainless Steel Channel letters with proper fabrication with 3mm acp female and 3mm day night acrylic in front having led of Samsung/GOQ having 5 years warranty and power supply of Union/Hi-sign with 3 years warranty. Letter height - 1000 mm Logo height - 1400mm Work complete including all type of material, fittings, fixtures, Finish, loading, unloading, transporation, all leads, accessories, sample mockup, all floor, all levels, all heights, scaffolding ,etc complete as per drawings, specifications & instruction of Client/EIC.

Signages-2 : Led Channel Letters: Main Building Terrace: Learning Resource Center: Supply and installation of 3 inch embozz Stainless Steel Channel letters with 3mm acp female and 3mm day night acrylic in front having led of Samsung/GOQ having 5 years warranty and power supply of Union/Hi-sign with 3 years warranty. Letter height - 450 mm Logo height - 1300mm Work complete including all type of material, fittings, fixtures, Finish, loading, unloading, transporation, all leads, accessories, sample mockup, all floor, all levels, all heights, scaffolding, etc complete as per drawings, specifications & instruction of Client/EIC.

Fabricated : Design, Fabrication & erection of steel structure as per drawings including materials, consisting of plates, rolled steel joists, channels, angles, chequered plates etc and also rectangular / square hollow steel sections, insert plates in RCC/Brickwork, anchor bolts for steel structure, sleeve pipes, anchor nuts, washers etc, straightening of raw steel if required, fabrication of steel structures with primer and minimum two coats of anti corrosive paint including preparation of supplementary sketches and detailed bill of materials supply of bolts, nuts, washers, shims, packs, putty. gas, welding electrodes and all other consumables, as required and carrying out surface preparation all complete. The scope includes loading, transportation ,unloading and delivery and erection site of all fabricated structures,, alignment and welding of all structures true to line, level, plumb and dimension, including rectification if any, splicing, site assembly all as per technical specifications and drawings, ,all complete. Contactor shall provide stability certificate for the fabrication structure. Rate inclusive of shop drawing.

Alluminium & Glass Railing: Providing and fixing of Alluminium (6063) glass balcony railing with powder coated as per approved shade by Architect/ Client. ( Remson or equivalent make as per approved by Architect/client) System : Signature Line Continue Profile System Dimension : 75mm x 125mm , Hand Rail : Reactangle Handrail Hadrail Dimension : 60mm x 40mm Glass Specification : 10mm Clear Toughened + 1.52mm Sentey Film ( Kuraray Make ) + 10mm Clear Touhenend Railin Height : 1205mm , Custmised Wall Conceal Aluminium Make With 10mm x 120mm Hilti HRD Fastner.Hilti Chemical Fastner 10 x 40 with SS threaded Rod for Bottom Profile,EPDm Gasket As Per Glass size Work complete including all type of material, fittings , fixtures, Finish, loading , unloading , safety measures , transportation, all leads ,accessories, groove, PVC edge banding, adhesive ,tape, headless nails, sample mockup, all floor , all levels, all heights etc complete as per detailed drawings ,specifications & instruction of Client/EIC. Aluminium Powder coating-50 microns Powder coating 15 years warranty.only the clear elevation area shall be measured and paid. sample mock shall be approved from Architect/Client. Work complete including all type of material, anchor fastening, fittings , fixtures, Finish, loading , unloading , safety measures , transportation, all leads ,accessories, sample mockup, all floor , all levels, all heights etc complete as per detailed drawings ,specifications & instruction of Client/EIC. sample mock shall be approved from Architect/Client.

LIFT: 20 Passenger, 20P-1.75 MPS - GeN2-Stream_MRL-1.75MPS (SCHINDLER/OTIS) Supply, Installation, Testing, & Commissioning of Passenger lift as per approved make, shop drawing & sample by Architect / Client. work complete including all type of scaffolding , loading , unloading , transportation, fittings, fixtures , all type of safety measures, equipment , at all floor, all levels etc. complete as per shop drawings and specifications. Sample mock & Shop drawing shall be approved from Architect/ Client. No extra charges will be paid for any scaffolding required for installation of lifts works. The intending bidder should visit the site prior to the bidding submission. Rate shall be quoted only after by initial site inspection further no discrepancy will be allowed for whatsoever reason. As per attached technical specification data sheet in tender documents. • PRODUCT: GeN2-Stream_MRL-1.75MPS • DETAILS: GeN2-Stream_MRL-1.75MPS • CAPACITY (kgs) : 1360Kg,20 persons. • SPEED (mps) : 1.75 mps • RISE (m) : 20m • STOPS : 7 Stops With (all opening on the same side) • CONTROLLER TYPE : ACD5-MRL • DRIVE : VF Regenerative (Closed Loop) • POWER SUPPLY : 400/415 Volts (3 Phase AC) • OPERATION : Full collective operation • CAR GROUP : Two cars (Duplex) • MACHINE : PM Gearless (Located in shaft on top of guide rails) • TRACTION MEDIA : Flat Coated Steel Belt • CAR FINISH : Rear Mid Panel = Stainless Steel #4(Hairline) , Rear Corner Panels = Stainless Steel #4(Hairline) , Side Mid Panels = Stainless Steel #4(Hairline) , Side Corner Panels = Stainless Steel #4(Hairline) , Front Panels = Stainless Steel #4(Hairline)., • FALSE CEILING TYPE : CD-63 • FLASE CEILING FINISH : Stainless Steel #4(Hairline) • VENTILLATION : Cross flow fan • HANDRAILS : Stainless Steel Mirror Finish Handrails on rear car panels • FLOORING : Flooring By Client • CAR DOOR FINISH : Stainless Steel #4(Hairline) • LANDING DOORS FINISH : Stainless Steel #4(Hairline) • FIRE RATED DOORS : Fire rating-120mins • PIT DEPTH : 1600 • OVERHEAD : 4500 • HOISTWAY DIMENSIONS (W x D – mm) : 2300 mm W x 2800 mm D • CAR DIMENSIONS (W x D x H - mm) : 1300 mm W x 2400 mm D x 2400 mm H • CAR & HOISTWAY DOOR TYPE : Telescopic opening (TO) doors • DOOR OPENING (W x H - mm) : 1100 mm W x 2100 mm H • DOOR OPERATOR : DC Door Operator • COP : Stainless Steel #4(Hairline) • CAR POSITION INDICATOR : Monochrome LCD-Blue Background & White font • HALL FIXTURES : O2000 Pan Type Fixture, • HALL FIXTURE FACE PLATE : Stainless Steel #4(Hairline) • HALL BUTTON ARRANGEMENT : LCD Monochrome type • STANDARD FEATURES : Anti-nuisance Car Call Protection , Independent Service (for Duplex only) , Overload Device , Nudging , Emergency Car Light Unit , Infrared Curtain Door Protection , Door Time Protection , Emergency Alarm Button , Extra Door Time of Lobby & Parking, Door Open/Close Button , Manual Rescue Operation , Belt Inspection Drive , Auto Fan Cut Off., • OPTIONS INCLUDED : Emergency Firemen’s Service, Automatic Rescue operation, Voice Synthesizer, Intercom. Note : Liasioning for all statutory approvals pertaining to Lift Installation with certification from Govt.Authority for Licensee for operation of Lift at Site with all clearance shall be in scope of Contractor . Extra charges pertaining to liasioning / licence & third party certification & Inspection shall be in scope of Client.

Comprehensive Maintenance : 20 Passenger LIFT (2 Nos) : everything is cover parts , accessories , machineries etc. Comprehensive Maintenance : 20 Passenger LIFT (2 Nos) : 7 STOP, 1.75 MPS: Second Year

Comprehensive Maintenance : 20 Passenger LIFT (2 Nos) : 7 STOP, 1.75 MPS: Third Year

Comprehensive Maintenance : 20 Passenger LIFT (2 Nos) : 7 STOP, 1.75 MPS: Fourth Year

Comprehensive Maintenance : 20 Passenger LIFT (2 Nos) : 7 STOP, 1.75 MPS: Fifth Year

Monorail façade cleaning systems : Design, Fabrication, installation & commissioning Facade access system - Supply, installation, testing & commissioning of Aluminium Monorail System with cradel with all type of fittings , fixtures , loading , unloading , Hoisting, Assembly of Monorail Bracket , Alignment of Monorail etc complete as per approved sample by Architect/Client. 1. STANDERD CRADLE : 1 Nos • 2 Man Aluminium Al loy Power Suspended Cradle, safety devices, wire rope reelers, rope climbing machine, Electrical & accessories. Safe working load 240kg. Two person & cleaning tools. ( Hoist & Safety devices As per CE- Regulation & international standard EN-1808.) 2. MONORAIL SYSTEM -SOFFIT LEVEL • Aluminium Monorai l T6 6061 : @ 83 Rmt or as per Drawing. • SOFFIT Mounted Monorai l Bracket (Including sims/ packing) as per Drawing- confirming to IS 2062 E250 Fe410 Hot dip galvanized - As per IS 2629 , approx 88 to 100 microns coating : 56 Nos • Mechnical Anchors (Kl imas Make )LE-A4-16145 (M16 By 145 MM Long : 224 Nos • Monorai l Manual Trol ley : 4 Nos 3. INSTALLATION PORTION • Installation ,Testing ,Commissioning & Handover The Monorail System To The Client : 1 Job Work complete for at all floor, all level, all depth, all Height, all lead and lift etc. work complete as per the detailed drawing, approved sample, specifications and instruction of Architect/EIC. Sample mock shall be approved from Architect/EIC.

Gypsum False Ceiling - Toilet Passage: Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Grid ceiing - Toilet: Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Edge Pool 1: Front Entry side: Supply, Installation, Testing, & Commissioning of water body system as per approved make, shop drawing & sample by Architect / Client. work complete including all type of Material, labour, accessories, scaffolding , loading , unloading , transportation, fittings, fixtures , all type of safety measures, equipment, at all floor, all levels etc. complete as per shop drawings and specifications. Sample mock & Shop drawing shall be approved from Architect/ Client. 1. Open well Submersible Pump Horizontal, with 16 m3/hr@18 m, with Cast Iron Body and Stainless Steel pump motor shaft.5.0 HP Enclosure class: IP68, Insulation class: Class F Three Phase: 440v (1+1 ) make :- RR pump : 2Nos. 2. Water Foaming brass nozzles with air mixing bubbler effect, 25mm threaded MOC: BRASS, WITH BALL JOINT make:- wonderful water, 11Nos. 3. Warm White LED NOZZLES MOUNTED SS304 BOCY 18WATT CENTRE WHOLE TYPE LIGHTS Input Voltage:12V DC, make :- wonderful water, 11Nos. 4. Transformer for the all Under Water LED Light, which convert 12 dc v power., make:- wonderful water, 1Nos. 5. Electrical Cable For motor with Conduict Wiring 2.5 Sqmm 3 Core, RR cable, 200Mtrs., 6. Electrical Cable for light with Conduict Wiring 1.5 Sqmm 3 CoreRR cable, 200Mtrs. 7. uPVC BALL Valve Size: 3", astral / equivalent, 2Nos. 8. RB Make NRV for each pump outlet brass. PVC for pump safety, 2Nos., 9. uPVC Ball Valve Size: 1"., astral /equivalent, 13Nos., 10. uPVC Piping and Fitting, Type: Sch40 astral, 1Lot., 11. Control Panel for pumps and Lights (3Phase) make -wonderful water, 1Nos., 12. Trolly mounted water body filter system for water body with cleaning accessories make :- wonderful water, 1Set., 13. Adheshive chemical - epoxy, grout, joint fiiller., 1Job., 14. Labour, Supervision & Transportation for Complete Project with Operator Training, 1Job.

Edge Pool 2: Back side: Supply, Installation, Testing, & Commissioning of water body system as per approved make, shop drawing & sample by Architect / Client. work complete including all type of Material, labour, accessories, scaffolding , loading , unloading , transportation, fittings, fixtures , all type of safety measures, equipment, at all floor, all levels etc. complete as per shop drawings and specifications. Sample mock & Shop drawing shall be approved from Architect/ Client. 1. Open well Submersible Pump Horizontal, with 28 m3/hr@18 m, with Cast Iron Body and Stainless Steel pump motor shaft.7.50 HP Enclosure class: IP68, Insulation class: Class F Three Phase: 440v make :- RR pump, 4Nos. 2. Water Foaming brass nozzles with air mixing bubbler effect , 25mm threaded MOC: BRASS, WITH BALL JOINT make :- wonderful water, 29Nos. 3. Warm White LED NOZZLES MOUNTED SS304 BOCY 18WATT CENTRE WHOLE TYPE LIGHTS Input Voltage:12V DC.make :- wonderful water, 29Nos. 4. Transformer for the all Under Water LED Light,which convert 12 dc v power, make:- wonderful water, 3Nos. 5. Electrical Cable For motor with Conduict Wiring 2.5 Sqmm 3 Core, RR cable, 500Mtrs. 6. Electrical Cable for light with Conduict Wiring 1.5 Sqmm 3 CoreRR cable, 500Mtrs. 7. UPVC BALL Valve Size: 3", astral / equivalent, 4Nos. 8. RB make NRV for each pump outlet brass. PVC for pump safety, 4Nos. 9. UPVC Ball Valve Size: 1", astral /equivalent, 32Nos. 10. UPVC Piping and Fitting, Type: Sch40 astral, 1Lot. 11. Control Panel for pumps and Lights (3Phase) make -wonderful water, 1Nos. 12. Trolly mounted water body filter system for water body with cleaning accessories make :- wonderful water, 1Set., 13. Adheshive chemical - epoxy, grout, joint fiiller., 1Job., 14. Labour, Supervision & Transportation for Complete Project with Operator Training, 1Job.

Plumbing work

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.: 15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall: 40 mm nominal dia Pipes

50 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work: 65 mm nominal dia Pipes

80 mm nominal dia Pipes

100 mm nominal dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

100 mm nominal bore

Constructing masonry Chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm top and 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

100 mm S.C.I. trap with 100 mm inlet and 75 mm outlet

100 mm S.C.I. trap with 100 mm inlet and 100 mm outlet

S.C.I. gully or nahani grating 100 mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe: 40mm dia

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(G)110 mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure polythene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(F) 75mm

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc.: 75 mm dia

100 mm dia

Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID 200mm

Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID 250mm

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up tohaunches of S.W. pipes including bed concrete as per standard design : 200 mm diameter S.W. pipe

250 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 ( 1 cement : 4 coarse sand) including 500x450mm pre-cast RCC horizontal grating with frame complete as per standard design : With common burnt clay FPS (non modular) bricks of class designation 7.5

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 Osg inline type post carbon filter auto low & high pressure switches with following size of storage tank & LPH capacity & erected as directed with one year comprehensive maintenance guarantee. [C] 50 Ltr / Hr with 250 psi 2 nos booster pump

Supply, Installation, Testing & Commissioning of 3 Layered HDPE Tank @ Terrace. 20000 Litres.

HYDRO PNEUMATIC SYSTEM FOR DOMESTIC WATER DISTRIBUTION: A). Domestic Water Supply Distribution PUMP: Capacity per pump - 150 LPM 1 Set = 1 Nos. Pump (1 Working + 1 Standby - cascade operation) Total Capacity of System: 300 LPM Head - 60 mt Location - Pump Room Suction head - Negative Suction Variable Speed Hydro-booster System : Compact self contained Hydro-booster system comprising of following : In-line, vertical multistage, centrifugal clear water pumps with SS-304 casing, S.S 304 impeller and SS-304 shaft, C.I. Base CED coating & head TEFC motor (with mechanical seal) Vendor to submit performance curves and technical catalogue of the proposed model for review and information. The job shall include required size of Foot valve, Inlet Pipe, Outlet Pipe, Y Strainer, NRV, Inlet & Outlet Valves, Main Header Header, Pressure Valve, and all required accessories to complete the job. Panel mounted PLC based multi pump controller with large graphical display with VGA 240 x 320 pixels and variable frequency drive (VFD) integrated in a single body or as separate components with pressure sensor transmitter, IP 55 enclosure, diodes to indicate pump ready, pump running and fault condition. Each incomer and Outgoing feeder should be capable for protection against Overload, Short Circuit and Phase reversal condition. System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equipped with dry running protection. Indication of all type of faults / on-off status. Electronic type low water level controller with LED panel to operate pump (necessary contacts along with minimum one PLC operated spare contacts required), with probe & all control wiring from Panel to tank to operate the system automatic/manual & shall prevent the pump from dry running. Scope shall also include power and control cable of required size, termination, cable tray from Pump to Control panel etc. complete the job. Pre-charged diaphragm pressure vessel with interchangeable membrane, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc. complete (size of pressure vessel shall be as per manufacturer recommendation). Set of accessories such as GI headers of suction and discharge for (working and stand by pump assembly), control valves, non return valves, pressure switches, pressure transducers, pressure gauge etc. complete the job.

DRINKING FOUNTAIN Type-1: P8ACY- Cooling (Wall hanging) Supply installation, testing and commissioning of wall hanging drinking water fountain, mechanical operation Drinking water fountain with 60 LPH Cooling capacity, stainless steel body ,approx size 18 InchesX Depth 18 InchesX hight X18 Inches Width, SS Matte Finish, bubbler guard operated between 50 to 120 PSI. R134 refrigerant. Thermostat enabled to regulate the temperature. Refrigerated unit, With MDCU29, supply complete with all accessories. Shall comply with ANSI 117.1 and ADA. Shall be listed by Underwriters Laboratories to US and Canadian standards, GRIHA Certifide (Green Rating for Integrated Habitat Assessment), TUV- SUD Certifide and shall comply with ANSI/NSF 61 and NSF/ANSI 372.Make: OASIS Model- P8ACY. work complete including all type of hardware, fittings , fixtures as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client.

DRINKING FOUNTAIN Type-2: Model P8EBFSLY (Cooling unit ) Supply installation, testing and commissioning of wall hanging Split level drinking water fountain with integrated bottle filling station for Kids, Adults and Specially challanged, mechanical operation Drinking water fountain with 60 LPH Cooling capacity, stainless steel body ,approx size 18 InchesX Depth 35 InchesX hight X36 Inches Width, SS Matte Finish, bubbler guard operated between 50 to 120 PSI. R134 refrigerant. Thermostat enabled to regulate the temperature. Refrigerated unit, With MDCU29, supply complete with all accessories. Shall comply with ANSI 117.1 and ADA. Shall be listed by Underwriters Laboratories to US and Canadian standards, GRIHA Certifide (Green Rating for Integrated Habitat Assessment), TUV- SUD Certifide and shall comply with ANSI/NSF 61 and NSF/ANSI 372.Make: OASIS Model- P8SBFSLY.work complete including all type of hardware, fittings , fixtures as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client.

ELECTRICAL

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.: Group A

Group B

Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. : Group A

Group B

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.: 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.: 25 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.: 5/6 amps switch

2 way 5/6 A Switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.: 1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.: 1 or 2 Module

3 Module

4 Module

6 Module

8 Module

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.: 1 run of cable

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator): 6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.): 12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.: Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. ; 63 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.; 40 A

Supplying & erecting in earthpit of minimum bore dia. 225mm size approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover (A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test report must be submitted by Agency. [C] For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA)i.e. independent Earthing located in other than normal soil i.e. Soft Rock, Marshy Soil etc.. -Length of Pipe : 3 Mtrs. -Back filling Compound :2 nos Bags of 25 Kg.

Supplying and laying 50 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables ; (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

(J) 3 1/2 core 300 Sq.mm ( 150 Sq. mm 1/2 core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables; (A) 4 core 16 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable.; (C) 3 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.; (A) 4 core 10 Sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 6 sq. mm (19mm)

3 X 300 sq. mm (70mm)

3½ X 70 sq. mm (38mm)

4 X 10 sq. mm (25mm)

4 X 16 sq. mm (28mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

900 mm width X 62.5 mm depth X 2.0 mm thickness

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary finishing.

Providing and fixing printed instruction chart both in English and Gujarati and duly framed with front glasses, for treatment of person suffering from Electric shock with minimum 50" diagonally size.

Providing pair of rubber hand gloves suitable for working on 11 KV/22 KV supply.

Supply, Installation, Testing & Commissioning of RRU External Lighting Sub Panels. Incomer : 63Amp, 4P, MCB, 10KA Protection Relays, Indication Lamp, Multifunction Meter, CT etc. as per Single Line Diagram. Busbar Chamber : 63Amp, 4P, Aluminium Busbar, 25KA. Outgoing : 40Amp, 4P, MCB. 10KA - 10 Nos with Timer Switch & Contactor 40Amp, DP, MCB. 10KA - 6 Nos with Timer Switch & Contactor

Supply, Installation, Testing & Commissioning of RRU Library lighting Panel Incomer : 400Amp, 4P, MCCB, 25KA, LSIG Protection Relays, Indication Lamp, Multifunction Meter, CT etc. as per Single Line Diagram. Busbar Chamber : 400Amp, 4P, Aluminium Busbar, 25KA. Outgoing : 63Amp, 4P, MCB. 10KA - 20 Nos 40Amp, DP, MCB. 10KA - 8 Nos

Providing and laying non-pressure NP2 class (Light Duty) R.C.C pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150mm dia R.C.C. pipe

250mm dia R.C.C. pipe

300mm dia R.C.C. pipe

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground/ road surface for enclosing cable (A)50 mm outer dia

Supply Installation Testing Commisioning of Indoor Office Lighting 7-9w Recess Mounted Tiltable Spotlight downlighter with below features 1.Pressure die cast Aluminum alloy housing for better thermal conductivity. 2. With COb with Lens of 36-40 degree 3. Efficacy of Fixture more then or equal to 85 Lumens /watt Available with 5700K, 4000K & 3000K CCT. 4. CRI>80, High efficiency driver with inbuild surge protection, over voltage protection, short circuit protection and operating at >0.9 PF. <5% THD 5. LED life of more then 35000 Hrs @ L70. Approved makes : Philips,Havells,Lighting technolgies, Wipro,Tisva

"Supply Installation Testing Commisioning of OUTDOOR Recess mounted COB type cylinder Light 30W-35w Surface Mounted COB Spotlight downlighter with below features Pressure die cast Aluminum alloy housing for better thermal conductivity. Powder coated using Nano technology for longer durability. PS diffuser for optimum light transmission. Efficacy of Fixture above 95 Lumens /watt Available with 5700K, 4000K & 3000K CCT. CRI>80 High efficiency driver with inbuild surge protection, over voltage protection, short circuit protection and operating at >0.9 PF. <5% THD. Tiltable. LED life of 50000 Hrs @ L70. IP20 Protection Luminaire performance & Safety :IEC 60598, IS 10322-5, IS 161-03/05/06/07, Surge : IEC 61000-4-5, EMC : EN 55015. The product should be Manufactured in India (all the Components should be manufactured in India except the Led source which can be imported . (Approved Led source Nichia , Cree, Lumileds , Osram Only) PF >=0.95 and THD <=5 % (Certificate need to be submitted from NABL Accredited lab) The manufacturer should be ISO 9001 -2008 and ISO 14001 -2004 Company The manufacturer should have their own driver Manufacturing Facility. The manufacturer should have their own NABL accredited lab Equivalent to LIghting Technologies Intenso Max 1IP65 30w.or Equalant in Wipro/Tisva/Philips/Havells/Lighting technologies

"Supply Installation Testing Commisioning of Indoor deep Recessed Round downlight 18-21W Recess Mounted Round backlit downlighter with below features 1. Pressure die cast Aluminum alloy housing for better thermal conductivity. 2. PS diffuser for optimum light transmission. Round Version. 3. Efficacy of Fixture more then or equal to 85 Lumens /watt Available with 5700K, 4000K & 3000K CCT. 4. CRI>80, High efficiency driver with inbuild surge protection, over voltage protection, short circuit protection and operating at >0.9 PF. <5% THD 5. LED life of more then 35000 Hrs @ L70. Approved makes : Philips,Havells,Lighting technolgies, Wipro,Tisva

35MM PROFILE LIGHT : Supply Installation Testing Commisioning of Indoor recess mounted 35mm cut out (35x35mm profile light), Heavy aluminium Extruded Aluminium alloy Housing and polycarbonate diffuser profile for continous decorative illumination Anodised aluminium end caps firmly fixed on the aluminium extrusion Silver anodised finish for elegant look . Efficacy of Fixture >=100 Lumens/Watt suitable for self adhesive Strips with driver. Wattage should be 40-55w/m. Should have a dotless continuos effect. Should be operated using remote driver of 24V Dc kept at suitable locations for future maintainance. Approved makes : Philips,Havells,Lighting technolgies, Wipro,Tisva

"Supply Installation Testing Commisioning of Outdoor Architectural LED Flood light luminaire system power [(100W)± 5%] , Available in Cool / Neutral White color temperature (5700K / 4000K) ,CRI>70, SDCM<5 , LEDs used have a life of 50000 burning hrs. & Lumen maintenance as per L70, The Luminaire System efficacy of >150LPW. Made of high grade ADC 12 PDC Aluminium housing for rapid thermal healing & Powder coated by Corrosion resistant Nano coating technology. L Injection moulded special PC lens optics ,ensuring low glare & best in class uniformity. Encapsulated IP 67 high efficiency electronic driver having Aluminium extrusion construction with rated voltage of 140-270V, power factor > 0.95, THD <10%, Inbuilt surge protection of 6 KV and upgraded with integrated IP67 protected SPD of 20KV/10KA surge protection with all necessary safety protection like mis-wiring, Over voltage, Short circuit, Reverse Polarity protection. IES, LM 79, LM 80, & TTC certificates will be provided from NABL accredited lab. Certification: CE Certified, Design Patented/Registered, ROHS compliant, BIS Certification for Luminaires & Drivers Approved Make.: WIPRO/TISVA/HAVELLS/LIGHTING TECHNOLOGIES/PHILIPS"

Supplying and erecting approved make Pole (Standard ) Made from HR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759 with required base plate and integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement for cable terminationas erected on suitable foundation (included) with necessary nut-bolts/J-Bolts. as per details given by manufacturer considering site requirement. Color finish of the pole to be approved from the architect. Pole should be suitable for mounting post-top light on top. The length of poles are as below (D) 4 Mtr. Long 65mm Top X155 mm bottom dia, 3mm thickness.

"Supply Installation Testing Commisioning of Outdoor Architectural LED Flood light luminaire system power [(55W)± 5%] , Available in Cool / Neutral White color temperature (5700K / 4000K) ,CRI>70, SDCM<5 , LEDs used have a life of 50000 burning hrs. & Lumen maintenance as per L70, The Luminaire System efficacy of >150LPW. Made of high grade ADC 12 PDC Aluminium housing for rapid thermal healing & Powder coated by Corrosion resistant Nano coating technology. L Injection moulded special PC lens optics ,ensuring low glare & best in class uniformity. Encapsulated IP 67 high efficiency electronic driver having Aluminium extrusion construction with rated voltage of 140-270V, power factor > 0.95, THD <10%, Inbuilt surge protection of 6 KV and upgraded with integrated IP67 protected SPD of 20KV/10KA surge protection with all necessary safety protection like mis-wiring, Over voltage, Short circuit, Reverse Polarity protection. IES, LM 79, LM 80, & TTC certificates will be provided from NABL accredited lab. Certification: CE Certified, Design Patented/Registered, ROHS compliant, BIS Certification for Luminaires & Drivers Approved Make.: WIPRO/TISVA/HAVELLS/LIGHTING TECHNOLOGIES/PHILIPS"

Supplying and erecting approved make Pole (Standard ) Made from HR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759 with required base plate and integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement for cable terminationas erected on suitable foundation (included) with necessary nut-bolts/J-Bolts. as per details given by manufacturer considering site requirement. Color finish of the pole to be approved from the architect. Includues one arm of 600mm for monting street light at per required angle. The length of poles are as below (D) 4 Mtr. Long 65mm Top X155 mm bottom dia, 3mm thickness.

FIRE FIGHTING WORKS

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads.; 900 LPM at 35m Head

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction,Wall mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, with suitable Starter for Terrace booster pump suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required.

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100mm dia

150mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100mm dia

150mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.; 40m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gun Metal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.; 100mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 100mm dia

Supplying, installation, of MS Sleeves of 600mm length for following size; 40mm dia

65mm dia

100mm dia

125mm dia

200mm dia

Providing & Fixing of fire extinguishers with necessary accessories, stand, trolley, etc., ISI Marked portable fire extinguisher, 4.5 kg CO2 type fire extinguishers complete in all respect including initial fill and wall suspension brackets & shall conform to IS 2878

Providing & Fixing of fire extinguishers with necessary accessories, stand, trolley, etc., ISI marked Fire Extinguisher, Dry Chemical powder type capacity 6 kgs conforming to IS : 2171 including first fill & wall suspension bracket.

Charges for Liasoning with CFO and getting all approvals and permissions & NOC 's required for fire fighting at various stages & after completion of the project. (All official and receipted payments would be submitted and Re- imbursed) Taking approval /NOC form CFO

Supplying, installation, testing & commissioning of Photo luminescent non toxic, non radioactive, maintenance free self glowing exit signs comprising zinc sulphide chargeable crystals which can glow in dark; printed on U-1000 photo luminiscent aluminium sheet 1.0 mm thick containing luminiscent 111 as base chemical cover with UV stabilized coating job complete with SS screws for wall mounting or to be hanged on rust proof chain for ceiling mounting complete in all respects, plate size 12" X 18" (general size, may increase or decrease depending on site requirements). Make : Pro-lite, Supreent Creation, Auto-Glow, Agni

External Development (Paver block, Kerbing, stone sitting, otta etc.)

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Banking excavated earth in layers not exceeding 20 cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m : All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Exterior Paint: Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. ; 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Landscape Part: Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling with all lead and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site. work complete including royalty, all type of tools, tackles, scaffolding, safety measures, loading, unloading, transportation, all heights, all levels, all lead & all lift etc complete as per instruction of Architect/EIC. (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, work complete including royalty, all type of tools, tackles, scaffolding, safety measures, loading, unloading, transportation, all heights, all levels, all lead & all lift etc complete as per instruction of Architect/EIC. (manure measured in stacks will be reduced by 8% for payment) :

Rough dressing the trenched ground including breaking clods. work complete including all type of tools, tackles, scaffolding, safety measures, loading, unloading, transportation, all heights, all levels, all lead & all lift etc complete as per instruction of Architect/EIC.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation

Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered GMDC or any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

Providing and Displaying Travelers palm well developed with fresh & healthy leaves foliage 210 to 240 cm ht specimen in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and displaying of Areca Palm having ht. 1.80 m to 2.10 m with 8 to 10 suckers, well developed, fresh and healthy with lush green foliage in 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Croton Baby Golden (three in one)/ Lemon croton, having ht. 30cm, multi branches, well developed with fresh and healthy foliage in 25 cm size of Earthen pot/Plastic pot. as per direction of the officer-in-charge

Providing and stacking of Nerium oleander (kaner)/ Nerium Draf of height 60-75 cm. with 5-6 branches in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba dwarf dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and displaying of Dracaena Kedarnath, Dracaena mahatma, Dresina Red etc. having ht. 30 cm & above, well developed with good colorful foliage in 20 cm size of Earthen pot/ Plastic pot. & as per direction of the officer-in-charge.

Providing and displaying of Schefflera high colour (three in one), having ht. 25 cm to 30 cm, well developed with fresh and healthy foliage in 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Schefflera Varieged, mounted on moss stick 90 cm ht., 3 to 4 s placed in each pot at equal distance, well developed with full of fresh & healthy bright leaves from bottom to top in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Phoenix palm having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying Champions palm/ Mascarena palm well developed with fresh & healthy foliage leaves 150 to 180 cm ht in 35 cm Cement Pot as per direction of the officer-in-charge.

Providing and Stacking of Pandanus plant of height 90 -105 cm. multibranches, well developed in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and Stacking of Tarpeta plant of height 90 -105 cm. multibranches, well developed in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and Stacking of Green Erenthmum plant of height 90 -105 cm. multibranches, well developed in poly bags of size 25 cm as per direction of the officer-in-charge.

Rate Only Items

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS:9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. All works upto plinth level : Concrete of M10 grade with minimum cement content of 220 kg /cum

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level to all floor level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level to all floor level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT: 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand) incl. all floor, all height, all level .

CEMENT PLASTER (IN COARSE SAND): Providing and laying plaster in all floor, all height, all level : 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar creme out upto surface using white cement including rounding off junctions and extending them upto 15 cm along the wall,clearing with water and oxalic acid etc. as directed.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. : For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm.

Providing and fixing Expansion joint Capcell HD 100 Supreme & finish with PVC belt or equivalent make of 50 mm thickness of best qualtity, including cutting to required size and shape at all levels complete as directed by Engineer in charge. The works shall also including cost of primer in expansion joint and providing and laying polysulphide sealent at 1.5 kg per meter with providing backer road for expansion joints of BASF / Sika / Fosroc or equivalent make and make the joint water tightness as per direction of Engineer in charge.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish, Size of Tile 600 x 1200 mm : Equivalent to Varmora Letto steel 600x1200mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600 x 1200 mm : Equivalent to Varmora Letto steel 600x1200mm

Providing and laying Polished Granite stone flooring colour of Black, Cherry/Ruby Red or equivalent in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for window sills, door frame and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red (Door Frame)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for window sills, door frame and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red (Window sill)

Flush Door with glass view panel and finish with laminate : Providing and fixing in position 40 mm thick BWP grade single or double leaf flush doors of approved make and finished with both side 1 mm thick VNR laminate as approved sample, with glass view panel, 8mm thick toughened Milky glass view panel, Hardware system as per approved make & sample. (Hinges, Mortise lock , Horizontal grab bar, Door stopper, door closer). Door closer and mortise lock of Dorma/Geze/Haffle as per approved make by Architect. Hinges, Door stopper and other accessories of Kich/Ozone/Inox as per approved make by architect. work complete including all type of hardware, fittings , fixtures ,as per instruction of Client/ Architect etc complete as per detailed drawings and specifications. sample mock shall be approved from Architect/Client. Equivalent to VNR Series Laminate.

Fix glass : (Domal 27 mm series) Supply & Fixing of Fixed glass window with powder coated as per by approved make & sample by architect/EIC. frame section: 40 x 89 x 1.5 mm Glass : 5 mm thick cleaver reflectiive glass of saint gobain or approved make list including necessary fixtures and fastening , EPDN gasket, silicon sealent etc. complete as per detailed drawings, mock sample and specifications.

Awning window : (Domal 27 mm series) Supply & Fixing of Fixed glass window with powder coated as per by approved make & sample by architect/EIC. frame section: 45 x 45x 1.5 mm Glass : 5 mm thick tinted grey toughened glass of saint gobain or approved make list including necessary fixtures and fastening , EPDN gasket, silicon sealent etc. complete as per detailed drawings, mock sample and specifications.

Collapsible steel shutter: Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Precast cement concrete jali : Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. - 50 mm thick

WPC Jali : Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Polycarbonate sheet roofing : Providing and Fixing of COXWELL DOMES ROOF SYSTEM consisting of MultiCell Polycarbonate Panel System of approved color in 10 mm Thick (minimum) 6 WALL -5 CELL having uniform in color, Vertical Standing Seam manufactured at both sides of the panel. Snap-on connector to interlock the panels shall have a grip-lock double tooth locking mechanism Panel shall in fixed on M.S. Structure with Aluminum Extruded Single Piece Cleats in which 3 Self Drilling SDST Screw will be applied to handle best Up Lifting Pressure. Panel shall be co-extruded UV protected. The full system shall be fitted on MS purlins perpendicular to direction of sheeting with purlin spacing as specified by Manufacturer.7000N Tested as per ISO 6892:1998 and IS 1608:2005, as per design requirement. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheet which have been exposed to UV for a min of 500 Hours as per ASTM G155. Panel shall not have Yellowness Index as per ASTM D1925 of 15 units when tested on samples exposed to UV for 500 Hours as per ASTM G 155. U Value shall not be more than 1.9 W/m2K as per EN ISO 10077-2 :2018. Polycarbonate Panel Ends shall be closed with Aluminum U profile /F Profile as and when required. The rate includes cost of all the operations, labour and all materials involved such as bolts nuts and screws etc. and labour for cutting bending to required profile. Work complete for at all floor, all level, all depth, all Height, all lead and lift etc. work complete as per the Detailed specification, shop drawing , approved sample, instruction of Architect/EIC. Sample mock shall be approved from Architect/EIC. Roof plan area shall be measured for payment. (Note: MS Fabrication and steel work paid separately in KG)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class teak wood (Staircase)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall: 15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 80 mm nominal bore

Supply, Installation, Testing & Commissioning of Irrigation Yard Hydrant with 25mm Valve and Nozzle with Mounting Fabrication to complete the job.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32mm dia

Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID 100mm

Providing & Supplying of Class SN8 structured wall Polythelene piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with non-smooth External Annular corrugated and smooth internal surfaces (Double Wall) for non pressure underground Sewerage & Drainage application as per EN:13476-3 incuding all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to the departmental stores etc. complete (ID Dia). Pipe Dia. ID 150mm

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up tohaunches of S.W. pipes including bed concrete as per standard design : 100 mm diameter S.W. pipe

150 mm diameter S.W. pipe

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 ( 1 cement : 4 coarse sand) including 500x450mm pre-cast RCC horizontal grating with frame complete as per standard design : With common burnt clay FPS (non modular) bricks of class designation 7.5

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 450 C. The outlet temp. of the water should drop by 150C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

HYDRO PNEUMATIC SYSTEM FOR DOMESTIC WATER DISTRIBUTION: B). Irrigation Pump: Capacity per pump - 200 LPM 1 Set = 1 Nos. Pump (1 Working + 1 Standby - cascade operation) Total Capacity of System: 200 LPM Head - 40 mt Location - Pump Room Suction head - Negative Suction Variable Speed Hydro-booster System : Compact self contained Hydro-booster system comprising of following : In-line, vertical multistage, centrifugal clear water pumps with SS-304 casing, S.S 304 impeller and SS-304 shaft, C.I. Base CED coating & head TEFC motor (with mechanical seal) Vendor to submit performance curves and technical catalogue of the proposed model for review and information. The job shall include required size of Foot valve, Inlet Pipe, Outlet Pipe, Y Strainer, NRV, Inlet & Outlet Valves, Main Header Header, Pressure Valve, and all required accessories to complete the job. Panel mounted PLC based multi pump controller with large graphical display with VGA 240 x 320 pixels and variable frequency drive (VFD) integrated in a single body or as separate components with pressure sensor transmitter, IP 55 enclosure, diodes to indicate pump ready, pump running and fault condition. Each incomer and Outgoing feeder should be capable for protection against Overload, Short Circuit and Phase reversal condition. System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equipped with dry running protection. Indication of all type of faults / on-off status. Electronic type low water level controller with LED panel to operate pump (necessary contacts along with minimum one PLC operated spare contacts required), with probe & all control wiring from Panel to tank to operate the system automatic/manual & shall prevent the pump from dry running. Scope shall also include power and control cable of required size, termination, cable tray from Pump to Control panel etc. complete the job. Pre-charged diaphragm pressure vessel with interchangeable membrane, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc. complete (size of pressure vessel shall be as per manufacturer recommendation). Set of accessories such as GI headers of suction and discharge for (working and stand by pump assembly), control valves, non return valves, pressure switches, pressure transducers, pressure gauge etc. complete the job.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.: 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.: Telephone socket outlet

Bell push

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installing of Exhaust Fan in existing opening, including and making good the connection, damage connection, testing commissioning etc as required.: upto 450mm sweep

Extra for fitting of Lowers/shutters complete with frame for exhaust fan of all size.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator): 6 way , Double door

8 way , Double door

12 way , Double door

16 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator): 4 way (4 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.): 4 way (4 + 12), Double door

8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.: Single pole and neutral

Double pole

Triple pole

Triple pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.: 40 A

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. ; 40 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.; 25 A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.; 25 A

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V "C" curve TP MCB complete with connections, testing and commissioning etc. as required. Supplying and fixing 20 A, 240 V, SPN Industrial type socket

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Earthing with copper earth plate 600mm X 600mm X 3mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 75 mm X 12 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 75 mm X 12 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables ; (A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core)

(B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

(C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)

(E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core)

(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

(G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core)

(H) 3 1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core)

(I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cable.; (A) 3 core 2.5Sq. mm

(B) 3 core 4 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.; (A) 4 core 2.5 Sq. mm

(B) 4 core 4 Sq. mm

(C) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following size of cables.; (B) 4 core 16 Sq. mm

(C) 4 core 25 Sq. mm

(D) 8 core 2.5 sq.mm

(G) 12 core 2.5 sq.mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 10 sq. mm (19mm)

2 X 16 sq. mm (22mm)

2 X 25 sq. mm (22mm)

2 X 35 sq. mm (25mm)

2 X 50 sq. mm (28mm)

3 X 10 sq. mm (22mm)

3 X 16 sq. mm (25mm)

3 X 25 sq. mm (25mm)

3 X 35 sq. mm (28mm)

3 X 50 sq. mm (32mm)

3 X 70 sq. mm (35mm)

3 X 95 sq. mm (38mm)

3 X 120 sq. mm (45mm)

3 X 150 sq. mm (50mm)

3 X 185 sq. mm (57mm)

3 X 225 sq. mm (62mm)

3 X 240 sq. mm (62mm)

3½ X 25 sq. mm (28mm)

3½ X 35 sq. mm (32mm)

3½ X 50 sq. mm (35mm)

3½ X 95 sq. mm (45mm)

3½ X 120 sq. mm (45mm)

3½ X 150 sq. mm (50mm)

3½ X 185 sq. mm (57mm)

3½ X 225 sq. mm (62mm)

3½ X 240 sq. mm (62mm)

3½ X 300 sq. mm (70mm)

3½ X 400 sq. mm (82mm)

4 X 25 sq. mm (28mm)

4 X 35 sq. mm (32mm)

4 X 50 sq. mm (35mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm width X 50 mm depth X 1.6 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

225 mm width X 50 mm depth X 1.6 mm thickness

375 mm width X 50 mm depth X 2.0 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

300 mm width X 62.5 mm depth X 2.0 mm thickness

375 mm width X 62.5 mm depth X 2.0 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 62.5 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

750 mm width X 75 mm depth X 2.0 mm thickness

900 mm width X 75 mm depth X 2.0 mm thickness

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with proper insulation without leakage and earthing.

Supplying rubber matting of following thickness as per IS:15652/IEC 61111: (c)12mm

Supplying stand first AID box with antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-aid) adhesive tape for medicinal user, Scissors, anti-septic solution (Savlon or similar) etc. (All above contents shall be of standard makes)

Supplying FIRE bucket round bottom of 9 litres capacity made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and Red out side with FIRE mark, filled with dry-sand and kept on existing stand provided or hung on wall hook.

Supplying and erecting floor mounting stand for keeping four nos. of FIRE buckets comprising 1500 mm in length, 900 mm height frame made out of 30mm X30 mm X 4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of approved enamelled silver paint.

Wall hook 22 to 25 cms. projection for keeping fire buckets made out of 15 mm dia. M.S rod grouted in wall to a depth of minimum 15 cms.

Supply, Installation, Testing & Commissioning of RRU External Development Main Lighting Panel. Incomer : 200Amp, 4P, 25KA Microprocessor based MCCB, LSIG Protection - 1 Nos Protection Relays, Indication Lamp, Multifunction Meter, CT etc. as per Single Line Diagram. Busbar Chamber : 200Amp, 4P, Aluminium Busbar, 25KA. Outgoing : 63Amp, 4P, MCB. 10KA - 10 Nos Protection Relays, Indication Lamp, Multifunction Meter, CT etc. as per Single Line Diagram.

Providing and erecting iron clad cable route marker duly marked with ELE.CABLE of size 23 cm.X 12 cm. Flushed with ground in cement foundation as directed by Engineer in charge.

Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below ground across the road crossing or on floor with necessary material in an approved manner and making the ground as per original.(D) 300 mm dia

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for laying any size of cable or locating the fault all over the run and back filling the same and making the surface as normal ground.

Covering of cable with second class bricks or cement tiles laid cover the cable crosswise & also on both sides with covering of 7. 5 Cm. layer of sand above & below cable (16 bricks per meter)

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable (B)63 mm outer dia

Supplying, Installation, testing & erecting of Waterproof surface mounted 6-9w spike light High Efficacy and low power consumption, protection to surge and transients of upto 4kv, Good quality of light with >70 CRI, high quality constant current driver with a very high input voltage range of 100-240V AC, Protector made of flat glass and metalised reflector for wider and symmetric light distribution. Luminous Flux of luminaire to be more than 90 lumens per watt Min IP 65 Ingress Protection for Fixture and IP65 for Driver The product should be Manufactured in India (all the Components should be manufactured in India except the Led source which can be imported) . Approved makes : Philips,Havells,Lighting technolgies, Wipro,Tisva

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump). Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.: 180 LPM at 70m Head

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.; 200 mm. dia (wall thickness = 6.3 mm)

150 mm. Dia

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25mm dia

32mm dia

40mm dia

50mm dia

65mm dia

80mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 40mm dia

50mm dia

65mm dia

80mm dia

200mm dia

250mm dia

300mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 40mm dia

50mm dia

65mm dia

80mm dia

100mm dia

150mm dia

200mm dia

250mm dia

300mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 40mm dia

50mm dia

65mm dia

80mm dia

100mm dia

125mm dia

200mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. ; 80mm dia

100mm dia

150mm dia

200mm dia

250mm dia

300mm dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

3 way - 150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Upright Sprinkler

Horizontal side wall sprinkler

Concealed sprinkler

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.; 150mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 80mm dia

150mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.; 700mm

Supplying, installation, testing & commissioning of deluge valve (to be used for water curtains) UL listed with wet pilot basic trim assembly for DVA with test and alarm, drip and drain valve with water motor gong complete as required.; 50mm dia

80mm dia

100mm dia

150mm dia

Providing, installation, testing & commissioning of water curtain nozzle 15mm dia nickel chrome plated brass, BSPT, K-factor as per design consideration complete as required.

Providing, installation, testing & commissioning of electric release trim assembly for deluge wall with two way solelnoid valve, weather proof operation on 24 volts DC supply complete as required.

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. : All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge : Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

BPC Projects and Infrastructure Pvt. Ltd. (BID ID -3176037)