Construction of 2x8MVA, 33/11KV Substation (Indoor Type) at Kuraiya, Kiccha District U.S. Nagar and its associated 33KV Line (1.2Km U/G) and (5.3Km O/H) on turnkey basis

Amount

MS Round 32mm dia, 6.32 Kg/mtr for delta earthing of T/F Body,Structures and fencing

Gravel pitching of size 1/2" to 3/4"

G.I. Strip 65x6 mm.

G.I. Strip 50x6 mm.

33KV,10KA Lightening Arrestor

33 KV 1250A vertical Type Line Isolator with earth switch

Rail 90 Lbs

MS angle 50x50x6 mm for J-hooks

MS Bar,12 mm Dia for Steel reinforcement

M S angle 75X75X8 mm 4.5 M long for neutral structure

M.S. Channel 125x65x6 mm

M.S. Angle 75x75x8 mm

33 KV,10 KA Lightening Arrester

MS Plate 300x300x8 mm.

M.S. bolts & nut with washers.

S.T. Pole 11 mtr. Long SP-55(Bottom Portion hot dip Galvanized)

M.S. Channel 100x50mm for top channel & dropper channel, bus isolator, fuse set, isolator handle & transformer base

33 KV Bus isolator

33 KV Fuse set

MS Earthing rod 20x2500mm

GI Wire 6 SWG

33 KV lightening arrestor

33 KV Aluminium 3Cx50 sq. mm. XLPE cable from Incomer Panel to station transformer Pole

LT XLPE Cable 4Cx25 Sq.mm. for Stn. T/F to ACDB.

33/0.433 KV, 63 KVA Station Transformer

M.S. Bolt & Nut Off size

P.P. & Clamps for S.T. Pole SP-55 with nut & bolts

Clamp of required size for holding cable supporting angle, pipe, cable & bus isolator handle on double pole & bus bar gantry

Name plate for station transformer with clamp, nut & bolt

33 KV Danger board with clamp

Stone Pad 300x300x75

GI pipe 4" dia. 3mtr long

MS plate 300x300x8 mm

Cable jointing kit outdoor type suitable for 3Cx50 sq. mm. XLPE cable 33 KV.

Cable jointing kit indoor type suitable for 3Cx50 sq. mm. XLPE cable 33 KV.

S.T. Pole 8.5 mtr. Long SP-23(Bottom Portion hot dip Galvanized)

M.S. Angle 65x65x6 for bracing set, 2.7mtr.x2

M.S. Channel 100x50mm for top channel & dropper channel & TPMO handle

M.S. Angle iron 75x75x6 mm for TPMO & Fuse set (4 nos.x2.24 mtr.)

M.S. Angle iron 50x50x6 mm for cable support 2.24 mtr.x3No

11KV Polymer disc insulator B & S

11KV disc fitting for weasal

11KV TPMO complete

G.S. Stay set GI 1800x16 mm comp.

Stay wire 7/10

MS Earthing rod 20x2500mm

GI Wire 6 SWG

9KV 5KA lightening arrestor (Polymer)

11KV fuse set.

M.S. Bolt & Nut off size

P.P. & Clamps for S.T. Pole

Bracing Clamp for ST Pole

Stay clamp for ST Pole

Clamp of required size for holding cable supporting angle, cable & TPMO handle

Name plate of feeder

11 KV Danger board with clamp

Stone Pad 300x300x75

GI pipe 4" dia, 3mtr long

MS plate 300x300x8 mm

ACSR Dog conductor

33KV Polymer Pin Insulator with Pin

Connectors suitable for Dog

1. For LA

2. For Isolators

3. For T/F suitable for HT and LT side

4. For station transformer

PG clamps for dog Conductor

E-Clamps with nut & bolt

36 KV, 1250 A 3 Ph. Indoor type VCB with required CT PT, protective relays, metering equipments, extendible both side bus bar etc. (SCADA OPERATED)

(i) Incomer

(ii) Outgoing

(iii) 33 KV Bus coupler with bus riser

(iv) Bus PT

11 KV VCB I/C 500MVA, 800/400/5A, 24 V DC

11 KV VCB FDR 500MVA, 400/200/5A, 24 V DC

11 KV VCB 500MVA, Bus Coupler & bus riser, 24 V DC

MS channel 100x50 mm

M.S. bolts & nut with washers.

33KV Aluminium 3Cx400sq. mm. XLPE cable from Pole to Incomer panel.(1cable from new proposed line and 1 cable from existing 33KV KM Paper mill feeder.)

33KV Aluminium 3Cx300 sq. mm. XLPE cable from outgoing panel to power transformer (02Nos.).

Cable Aluminium 3Cx400 sq. mm. XLPE 11KV from Power T/F to 11KV Incomer VCB

Cable Aluminium 3Cx300 sq. mm. XLPE 11KV from outgoing VCB to outgoing feeder poles

MS Channel 125x65 mm

MS Channel 100x50 mm

MS Angle 75x75x8 mm

Cable jointing kit outdoor type suitable for 3Cx400 mm XLPE cable 33 KV.

Cable jointing kit indoor type suitable for 3Cx400 sq. mm. XLPE cable 33 KV

Cable jointing kit outdoor type suitable for 3Cx300 mm XLPE cable 33 KV.

Cable jointing kit indoor type suitable for 3Cx300 sq. mm. XLPE cable 33 KV

Cable jointing kit outdoor type suitable for 3Cx400 mm XLPE cable 11 KV.

Cable jointing kit indoor type suitable for 3Cx400 sq. mm. XLPE cable 11 KV

Cable jointing kit outdoor type suitable for 3Cx300 sq. mm. XLPE cable 11 KV

Cable jointing kit indoor type suitable for 3Cx300 sq. mm. XLPE cable 11 KV

HT Cable warning tape

GI pipe 6" dia, 3mtr long

GI pipe 4" dia, 3mtr long

Clamp of MS Flat 50x6 mm. of suitable size for holding 6" & 4" dia. Pipe

LT Control Cable

i. 10C x 2.5 Sq. mm.

ii. 4C x 2.5 Sq. mm.

iii. 2C x 2.5 Sq. mm.

MS Angle 50x50x6mm for cable trench

MS Angle 40x40X6mm for cable trench

MS Bar, 10 mm

Perforated tray for cable trench

(i) 400 mm width

(ii) 200 mm width

(iii) 100 mm width

8mtr long ST pole SP-10 (Bottom portion hot dip)

LT PVC cable 4x10 sq. mm.

LT PVC cable 2x6 sq. mm.

Stone pad 300x75 mm.

Iron clad 30 Amps water proof switch on the ST pole.

250W LED lamp with control gear & mounting accessories

150W, LED lamp with control gear & mounting accessories & 15 A MCB's

24 V Battery charger with boost & trickle charge

24 V Battery set Maint. Free 150 AH

DCDB 24 V

110V Battery charger 300AH

110 V Battery set 300AH

DCDB 110 V

Instruction board 3’x2½’ of Flex board duly printed.

Single line diagram of size 3’x2½’ on flex board, duly printed.

Maximum & tripping display board of size 5’x3’ of mica board moulded with frame duly painted & writing.

Sub-station named board (Size 3'x2' of MS sheet & MS angle 45x45x5 mm, Height 1.5 mtr. Above ground level ), duly painted

Name plate of equipment TG, LI, BI, PI, BG, CT, PT, CB, LA etc. (Size 9"x5" with white base, red border & letter written in red color)

Sundries items Cable tie, Alu lug, Copper lug & HT, LT tape, pvc compound, ferrule, pvc flexible pipe, paint writing on panels, HT LT diff size cable gland.

MS channel 100x50x6, (2.5x4x9.56) for gate

MS angle 40x40x5, 2.5 mtr long for stay

Fabrication & supply of Wire mesh frame made of 8 SWG wires frame of 40x40x5 mm angle M.S. (3mtr X 1.8 mtr), 35x5 mm MS flat & suitable 8mm plate including all material & labour charges

Fabrication & supply of 2 Nos, 2 mtr long, 1.8 mtr high wire mesh gate panels of 40x40x5 mm M.S.angle and 35x5 mm MS flat, with proper provision of locking arrangements in two piece. Including all material & labour charges.

Fabrication & supply of 1 Nos, 1 mtr long, 1.8 mtr high wire mesh gate panels of 40x40x5 mm angle M.S. (3 mrx1.8 mr), 35x5 mm MS flat, with proper provision of locking arrangements in one piece. Including all material & labour charges.

Steel office table, Godrej, (5'x3')

Steel office table, Godrej, (4'x2.5')

Steel Almirah, Godrej,

Steel cabinet, Godrej,

Steel office chair, Godrej,

Shock treatment chart

Danger board

Shut down / Break down board (Bi-lingual Hindi & English)

HT Hand Gloves

Wall Clock

Insulated electrical Plier Taparia

D-Spanner Set Taparia

3 cells Torch

Pipe wrench, 12" Taparia

First aid Box

Earth chain brass 12 mtr. Length

5 KV Megger Digital

2.5kv Megger Digital

Earth Megger Digital

Dust bin branded make

Doormat (5'x3')

Rubber mat Class C 3 mm Synthetic Insulating Mat- Confirming to IS 15652 : 2006. Along the all equipments in Control Room.

Carbon dioxide (CO2) type fire extinguishers conforming to IS 2878 - 1976 and cylinders fully charged of 4.5 Kg capacity.

Foam type fire extinguishers, Portable type 5 lit capacity hanged on wall with bracket complete as required

Metal Fire bucket Filled with sand

Fire bucket stand of Chuggi type of MS angle 50x50x6 mm with top covered by MS sheet 2 mm. thickness and Duly painted with red color including cost of all material, fabrication etc. complete work

Capacitor Bank, 3000KVAr

9KV, 10KA lightening arrestor

LT Control Cable

i. 4C x 2.5 Sq. mm.

ii. 6C x 2.5 Sq. mm.

iii 10C x 2.5 Sq. mm.

Cable Aluminium 3Cx240 sq. mm. XLPE 11KV

Cable jointing kit outdoor type suitable for 3Cx240 sq. mm. XLPE cable 11 KV

Cable jointing kit indoor type suitable for 3Cx240 sq. mm. XLPE cable 11 KV

11KV,630Amp off load Isolator with earth switch and mounting structure

Indoor type automatic power factor controller

11KV Outdoor VCB switchgear alongwith complete arrangement for connection

Indoor type control and relay panel

Lugs/thimble junction box, 2nos cable support structure etc.

Cable box of 2mm thick CRCA sheet of dimension 1000x600x500mm (HXWXD) with associated accessories.

CT outdoor with mounting structure (1Set=3 Nos)

Cable trench for laying of power and control cable

GI Earthing strip 35x6mm

Electrode Chemical earthing for equipments

Description of Work / Item(s)

Amount

Making of Delta/Bridge earthing for structure i.e. 33 KV LA, 11 KV LA, ACDB, DCDB, fencing,Body of power & station transformer.

Special earthing by digging 6mtr deep pits providing 6mtr GI pipe 45mm,40kg char coal,10Kg common salt,5kg copper sulphate,2 CI earth plate 450x450x20mm and making contact with GI Strip 50X6mm including supply of all material and T&P. (As per Drawing Enclosed)

Earthfilling in yard

Febrication and erection charges of 33KV Terminal D/P 8.5mtr long of RS joist 150x150mm with double top channel 125x65mmx3.2 mtr with bracing set and suitable channel mounted for fixing 33KV Vertical isolator and Lightening arrestor including supply of all materials.

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Fabrication of Rail 90 Lbs, cutting of MS angle 50x50x6 mm and MS Bar 12 mm

Excavation of earth in mixed soil

Brick work in 1:4

Plaster in 1:4

Erection of Power transformer by fixing all accessories, tank, filling of transformer oil etc.

Fabrication & erection of neutral structure including excavation & grouting in CC 1:4:8

Fabrication charges of structure as per approved drawing

Excavation of earth in mixed soil

Grouting of structure with C.C. in 1:3:6 ratio

Cement Plaster 1:4, on top & side walls

Erection charges of structure

Fixing and erection charges of Lightening arrestor

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Excavation of earth

Cement concreting of Double pole 1:4:8

Cement Plaster in 1:4

Fabrication charges of channels

Erection of Double pole complete with all fittings, channels etc. complete work

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Erection of 33/0.433 KV station transformer on double pole with all accessories complete work

Laying, spreading & jointing of LT cable by using propers ties, lugs, connectors, cable glands in cable trench and equipments..

Laying of 33KV Cable by excavation of cable trench in mixed soil, filling of the sand upto the height 250mm from the bottom most level of the cable trench thereafter properly laying of the cable by placing bricks on both side of the cable than re-filling of the sand from the top so as to cover the cable completely and then placing the bricks on the top of the covered cable, spreading of cable warning tape & covering of the trench completly with mixed soil including cost of sand, bricks, etc.

Filling of cable jointing kit 33 KV indoor and outdoor type

Erection of vertical 33 KV bus isolator on double pole SP-55 complete by assembeling, fixing of operating handle, pipe, clamps, pins etc for smooth operation of the isolator.

Erection of 33 KV fuse set on double pole SP-55.

Excavation of earth

Cement concreting of Double pole 1:4:8

Cement Plaster in 1:4

Fabrication charges of channels & angle

Erection of Double pole complete with all fittings, accessories, stays & earthing.

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Flexible copper connection on neutral bushing of power & station transformer 500X50 mm heavy duty with copper lug at ends.

Labour charges for drawing bus-bar & making connection in each equipment, main & auxilary bus bar.

Placing of panels on specific place over SGR trench on MS Channels and fixing of pannels with nut & bolts.

Making electrical connection of panels by control wiring complete with & VCB etc.

Manual shifting of 11 kv VCB from road side to SGR

Fixing and erection of 11KV Panels

Fabrication of MS channel

Laying of 33 KV/ 11 KV Cable by excavation of cable trench in mixed soil, filling of the sand upto the height 250mm from the bottom most level of the cable trench thereafter properly laying of the cable by placing bricks on both side of the cable than re-filling of the sand from the top so as to cover the cable completely and then placing the bricks on the top of the covered cable, spreading of cable warning tape & covering of the trench completly with mixed soil including cost of sand, bricks, etc.

Filling of cable jointing kit 33 KV indoor & outdoor type

Filling of cable jointing kit 11 KV indoor & outdoor type

Fabrication charges of MS items

Fixing of GI Pipes

Erection of cable supporting MS Channel & angle

Fabrication charges of MS item

Making cable trench.including fabrication, fixing of MS angle 50x50x6 mm size (excluding the cost of MS Angle/ MS bar) on side edge with all excavation, CC work, brick work, fixing of cable support angle one/two tier as required with stopper arrangement at 0.5 mtr gap throughout the length of the trench, making of cable trench covers with MS Bar welded mesh angle frame of MS angle 40x40x6 mm. with lifting hooks, fixing of perforated tray complete as per drawing including cost of sand, cement, bricks, metal (gitti) etc.

Laying, spreading & jointing of LT control cable by using propers ties,lugs, connectors, cable glands in cable trench and equipments..

Excavation of earth

Cement concreting in 1:4:8 ratio

Erection of ST Pole SP-10 and fitting of accessories.

Painting of ST Pole with one coat of red oxide primer and two coat of Aluminium paint

Erection of 250 watt & 150 watt lighting equipment & all its accessories

Laying of LT PVC cable 4x10 sq. mm. in soil & back filling of sand.

Erection of 24 V Battery charger with boost & trickle charge

Erection of 24 V Battery set Maint. Free

Erection of DCDB 24 V

Erection of 110V Battery Charger

Erection of 110 V Battery set

Erection of DCDB 110 V

Erection of ACDB

Erection of Name plates, instruction board, SLD, Max., Min. board etc.

Erection of substation name board by grouting in CC 1:4:8 ratio

Erection of stays post of 40x40x5 mm angle 2.5 mtr long. with required CC 1:4:8 work of size .5x.5x.5

Fabrication & Erection of M.S. Channel 125x65mm size 3.5x2 for fixing of wire mesh gate including grouting of the pillar.

Erection, grouting & fixing of pre-fabricated wire mesh of size 3x1.8 mtr with proper levelling and alignments on toe wall with the CC 1:3:6 in size 0.45x0.45x.60 and all the pieces duly weldded with angle joints. Including all material, labour charges & tack welding.

Painting of both side of wiremesh fencing with one coat of red oxide paint and two coat of Bus green paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide paint.

Painting of stays with one coat of red oxide paint and two coat of Bus green paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Fixing, placing and erection of T&P and furniture material

Instalation/Mounting of Fire Extinguishers

Construction of Plinth for all equipment.

Fixing and erection of 3000KVAr Capacitor Bank

Fixing and erection of 11KV,630Amp off load Isolator with earth switch and mounting structure

Fixing and erection of Indoor type automatic power factor controller

Fixing and erection of 11KV Outdoor VCB switchgear including fixing of all cable joint

Filling of cable jointing kit 11 KV indoor & outdoor type.

Laying of power and control cable in trench including all connections.

Insured Carriage of 8 MVA Power Transformers from Electricity Store Center to substation site including safe loading, unloading to transformer plinth.

Construction of Control Room Building at 33/11 KV Substation at Kuraiya, Kiccha District U.S. Nagar

Land Development Works (Boundary Wall, Approach Road and Other Miscellaneous Civil Works) at 33/11 KV Substation Ranipokhari District - Dehradun

Description of Work / Item(s)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size

P/L in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level.1:1.5:3 (1 cement : 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: Foundations footings, bases of columns, etc. For mass concrete.

Centering and shuttering including strutting propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting propping etc. and removal of form for: Shelves (Cast in situ)

Centering and shuttering including strutting propping etc. and removal of form for: Lintels, beams, plinth beams girders, bressumers and cantilevers,

Centering and shuttering including strutting propping etc. and removal of form for:. Columns, Pillars, Piers, Abutments, Posts and Struts.

Centering and shuttering including strutting propping etc. and removal of form for. Weather shade, Chajjas, corbels etc. including edges.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

P/f 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade,colour & texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

P/f 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

P/F ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 200x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish (Barrel type) with necessary screws etc. complete : 100x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm

P/F aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS:1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :(200x10mm)

Providing and fixing aluminium tower door bolts ISI marked anodised (Anodic coating not less than grade AC 10 as per IS:1868)transparent or dyed to required colour or shade with nuts and screws etc. complete: (150x10mm)

P/F aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125mm

Providing and fixing aluminium handles floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary scerews etc. complet: Single rubber stopper

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood

P/F in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

P/ fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm hickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer in-charge:Profile E Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

P/fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate.

P/fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick

P/fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 oarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622 , of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (75mm diameter)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.( 110mm diameter)

12mm cement plaster of mix: 1:4 (1cement : 4coarse sand)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Supplying and stacking at site.Good earth

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing terminal guard : 75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 20mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making ecessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.(15 mm nominal bore)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

P/Fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Engaging suitable Beldar for petty works (Basis rate labour)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. GROUP C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2*2.5 Sq.M+1*2.5Sq.m earth wire.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including nnections but excluding modular plate etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted ncluding earthing etc. as required. (But without MCB/RCCB/Isolator) 2 + 6 way/ 8 way , Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing following rating, double pole, 240 volts,isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Boring 140mm dia with casing pipe to aprobable depth from 0 to 60 meter from ground level with skilled and unskilled labor including all T&P boring apparatus supervision charges etc. required for proper completion of work.

Supply and lowering of 110mm dia PVC strainer pipe (10kg/cm2)of approved quantity with 25mm dia holes covered with best quality PVC mesh as per direction of E/I including cost of all material, Labor, T&P etc.

Supply and lowering of 110mm dia PVC pipe (10kg/cm2)of approved quantity as per direction of E/I including cost of all material, Labor, T&P etc.

Supply and Installation 40mm outlet size submersible pump set 1.00HP, I stage of crompton greaves or equivalent make

Supply and Placing single phase panel board/ box crompton greaves make or equivalent make with flat submersible copper cable 1.50 sqm (panel to submersible pump set ) including auto start stop button, push button for volt meter indicator complete in panel board/ box for submersible pump set Installation 32mm outlet size submersible pump set.

Supply and fixing of 4 sqm cable for laying of submersible as per direction of E/I including cost of all material, Labor, T&P etc.

Providing and Fixing Havells make or Equivalent make 20 W LED with single side connection with all fittings Labour, Material, T&P etc. required for proper completion of work.

Supply of 1200 mm sweep ceiling fan of approved quality ( Bajaj,USHA, Havells or equilent make) without regulator.

Providing and Fixing Crompton Industrial Exhaust Fan or Equivalent make (Multi colour 18-inch) with all fittings Labour, Material, T&P etc. including installation, Testing and commissioning complete in all respect.

Providing and Fixing Bajaj Bahar or Equivalent make 225 mm Matellic grey Dom Exhaust Fan with all fittings Labour, Material, T&P etc. including installation, Testing and commissioning complete in all respect.

Description of Work / Item(s)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level.1:1.5:3 (1 cement : 1.5coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: Lintels, beams, plinth beams girders, bressumers and cantilevers,

Centering and shuttering including strutting propping etc. and removal of form for:. Columns, Pillars, Piers, Abutments, Posts and Struts.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

15mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1cement :6coarse sand)

Finishing walls with water proffing cement paint on required shade: New work (Two or more coats applied @ 3.84kg/10sqm

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Supplying and stacking at site.Good earth

Engaging suitable Beldar for petty works (Basis rate labour)

Stone tile work for wall lining upto 10m height with special adhesive over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement with an admixture of pigment to match the stone shade. (i) 12mm thick stone Textured Exterior cladding tiles.

Description of Work / Item(s)

Amount

ST pole SP- 55, 11 mtr long (Bottom portion hot dip galvanised)

33KV streight/L type X arm (125x65mm) 2.4x13.5x1

Supporting angle for top channel 65x65x6mm (1.5x2x6.5)

33KV Polymer pin insulator with pin

PP clamp with bolts and nut

Supporting clamp for top channle

Earth wire clamp with nut and bolt

Bolts and nuts

Stone pad

Alluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make.

Red oxide paint of best quality I.S.I. mark Dulux, Burger, Asian make.

Danger bord with clamp

Number plate

Barbed wire

ST pole SP- 72, 13 mtr long (Bottom portion hot dip galvanised)

MS channel 125x65mm 3.2mtr long top channel 13.5kg/mtr

33 KV Polymer disc insulator B&S Type

33KV disc fitting for dog conductor

MS angle 65x65x6mm 3.8mtr long 2x3.8mm @6.5kg/mtr

E clamp with bolts & nuts

PG clamp dog to dog conductor

Bracing set clamp 135mm

Bracing set clamp 165mm

33 KV Disc fitting for Panther conductor Suspension B&S Type

Fabricated & Galvanised 33 KV Single Circuit 'M' type Tower

Number plate with clamp,N&B

Danger Board with clamp,N&B

RYB coloured phase indicator

Cross bridge damper for Dog conductor conductor

Bird guard for 33KV Tower

GI Fitting for earthwire 7/16 bolted

Fabricated & Galvanised + 3 mtr. Extension for 33 KV Single Circuit 'M' type Tower

Earthing rod 20x2500 mm.

GI stay wire 7/10 SWG

GI lug for 7/10 SWG Stay wire

Stay set GI 20x1800 mm

Stay wire 7/8 swg

Stay clamp with nut & bolt

Earthing rod 20x2500mm

GI wire 6 SWG/Earth wire

Bolt & nut 150x12mm

Bolt & nut 50x16mm

Stone pad 300x300x75mm

MS angle 75x75mm 3.5mtr long (2x3.5)x7.3

Earth wire 7/16 SWG

GI wire no. 8 SWG

Eye bolts

ACSR dog conductor

MS Angle 65x65x6mm 8x4x6.5

MS Angle 50x50x6mm 0.4x40x5

Clamp for holding cable made of MS flat 50x6mm

GI Strip 50x6mm 11x2.5

Cable AL 3X400 Sq.mm XLPE 33KV

Cable jointing kit for 33 KV XLPE 3x400 Sqmm Outdoor

GI Pipe 6" dia 3mtr long

Description of Work / Item(s)

Amount

Excavation of earth pit.

Erection of Single pole complete with all fittings & accessories.

Grouting of pole in CC ratio 1:4:8 cement ,sand, 20mm gauge stone ballast (0.45x0.45x1.8)

Muffing of Pole in 1:3:6 CC size of 0.45x0.45x 0.4 mtr.

Fabrication charges of channels & angle

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint.

Excavation of earth pit.

Erection of Double pole complete with all fittings & accessories.

Grouting of pole in CC ratio 1:4:8 cement ,sand, 20mm gauge stone ballast (0.45x0.45x1.8x2)

Muffing of Pole in 1:3:6 CC size of 0.45x0.45x 0.4x2 mtr.

Fabrication charges of channels & angle

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint.

Excavation of earth pit.

Erection of Four pole complete with all fittings & accessories.

Grouting of pole in CC ratio 1:4:8 cement ,sand, 20mm gauge stone ballast (0.45x0.45x1.8x4)

Muffing of Pole in 1:3:6 CC size of 0.45x0.45x 0.4x4 mtr.

Fabrication charges of channels & angle

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint.

Excavation of earth in mixed soil including back filling of soil, levelling work after completion of founadation work

Setting of stub of 33 KV Single Circuit Tower type 'M' using Tan plates etc. complete work

Erection of 33 KV Tower including all work above ground level including tightening of bolts at required torque using torque wrench.

Erection of the following equipments on tower

Disc Fitting for Dog conductor

33 KV Polymer Disc Insulator B&S type

Number Plate with clamp, nut & bolt

Danger Board with clamps, nut & bolt

PG clamps for Dog Conductor

RYB coloured phase indicator

cross bridge damper for Rabbit conductor

Bird guard for 33 kv tower

G.I fitting for earthwair 7/16 bolted

Erection of + 3 mtr. Extension for 33 KV Tower including tightening of bolts at required torque using torque wrench

Earthing of 33 KV tower including excavation of earth, inserting of earth rod in earth so that the top remains 600 mm below ground & connection of 7/10 SWG stay wire using lugs at both ends.

CC 1:4:8 ratio=0.6x0.6x0.3

Erection of stay including excavation of mixed soil

Erection of earthing

Civil work CC 1:4:8=0.45x0.45x1.8

Erection of stud stay

Fabrication & Erection charge for guarding complete.

Erection charges of 3 Phase 4 Wire 33 KV Line

Exacavation of earth in all type of soil 4x0.6x0.6

Febrication Charges

Grouting of cable stand in CC 1:3:6 (0.6X0.6X4) including muffing.

Earthing of cable stand structure with making triangle GI Strip bridge including supply of all material.

Painting charges of cable stand complete with one coat of red oxide and two coat of Aluminium paint.

Fixing of 33 KV 3 core XLPE outdoor cable box of 400 Sqmm

Laying of D/Ckt 33KV 3X400Sqmm cable including proper cable loop at both end and filling of earth with sand and brick work for separate the cable from each other including fixing the GI Pipe,Cable jointing kit etc.

Lopping chopping of tree branches etc.

Suryacon Engineers

SATYESWARI POWER AND CONSTRUCTION PVT. LTD.

Zetwerk Manufacturing Businesses Private Limited

M/s Kashmirilal Constructions Pvt. Ltd.

T S Power Co

Suryacon Engineers

Zetwerk Manufacturing Businesses Private Limited

Raoyal Infra Power Corporation

T S Power Co

M/s Kashmirilal Constructions Pvt. Ltd.

Suryacon Engineers

M/s Kashmirilal Constructions Pvt. Ltd.

SATYESWARI POWER AND CONSTRUCTION PVT. LTD.

Zetwerk Manufacturing Businesses Private Limited

T S Power Co

Suryacon Engineers

SATYESWARI POWER AND CONSTRUCTION PVT. LTD.

Zetwerk Manufacturing Businesses Private Limited

M/s Kashmirilal Constructions Pvt. Ltd.

T S Power Co

Suryacon Engineers

SATYESWARI POWER AND CONSTRUCTION PVT. LTD.

Zetwerk Manufacturing Businesses Private Limited

M/s Kashmirilal Constructions Pvt. Ltd.

T S Power Co

Suryacon Engineers

SATYESWARI POWER AND CONSTRUCTION PVT. LTD.

Zetwerk Manufacturing Businesses Private Limited

Raoyal Infra Power Corporation

T S Power Co

SATYESWARI POWER AND CONSTRUCTION PVT. LTD.

Suryacon Engineers

Zetwerk Manufacturing Businesses Private Limited

Raoyal Infra Power Corporation

T S Power Co