Construction of Parha Cultural House at Jhariya Dipa Near Dari Tongri, Sisai block, district Gumla.

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. (BCD SOR Item No-5.1.1)

Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume) (BCD SOR Item No-5.1.7)

Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume) (BCD SOR Item No-5.1.8)

Providing coarse clean sand filling in Foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) (BCD SOR Item No-5.1.10)

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. (BCD SOR Item No-5.6.3)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size) (BCD SOR Item No-5.3.1.5)

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. (BCD SOR Item No-5.2.3)

Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. (BCD SOR Item No-5.2.11)

Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I. (BCD SOR Item No-5.2.23)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) (BCD SOR Item No-5.3.9.1)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). (BCD SOR Item No-5.3.11)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size) (BCD SOR Item No-5.3.10)

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 50 mm thick (BCD SOR Item No-5.3.21.1)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). (BCD SOR Item No-5.3.5)

providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL) (BCD SOR Item No-5.5.4)

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. (a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)} (BCD SOR Item No-5.5.5 (a))

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. 5.5.5(b) 12mm (c) 16mm & 5.5.6(a) 20,25mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}) (BCD SOR Item No-5.5.5 (b))

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. 5.5.5(b) 12mm (c) 16mm & 5.5.6(a) 20,25mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}) (BCD SOR Item No-5.5.5 (c ))

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. 5.5.5(b) 12mm (c) 16mm & 5.5.6(a) 20,25mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}) (BCD SOR Item No-5.5.5 (b),(c ) &5.5.6(a))

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. (BCD SOR Item No-5.4.38)

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I. (BCD SOR Item No-5.4.1)

Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick (DSR Item No-9.127.1)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) (DSR Item No-21.1.1.3)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) (DSR Item No-21.3.1)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) (DSR Item No-21.3.3)

Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.) (BCD SOR Item No-5.5.12)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (DSR Item No-10.28)

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I. (BCD SOR Item No-5.5.14)

Supplying, and fixing fan hook of 16mm dia M.S. bar 1 meter long bent to required size and shape , placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. (where materials is not supplied by the deptt.) (BCD SOR Item No-5.5.13)

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm (DSR Item No-9.96.2)

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . (BCD SOR Item No-5.6.28)

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (iv) 600X600 mm size (BCD SOR Item No-5.6.19)

Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (BCD SOR Item No-5.6.20)

Providing and laying 25mm thick white makrana marble stone slab flooring of approved quality over 19mm thick base of lime mortar (1:1:1) (Lime putty: surkhi: coarse sand) laid and joined with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (i) 300X300 mm size (BCD SOR Item No-5.6.21)

Providing and laying 25mm thick white makrana marble tiles in risers of steps, skirting and pillers of approved quality over 12mm thick base of cement mortar (1:3) and jointed with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (BCD SOR Item No-5.6.22)

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. With "A" grade white 15X15cm Tiles. (BCD SOR Item No-5.6.23.1)

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. (BCD SOR Item No-5.7.3)

Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. (BCD SOR Item No-5.7.6)

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. (BCD SOR Item No-5.7.14)

Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete. (DSR Item No-12.20)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. (DSR Item No-13.26)

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I. (BCD SOR Item No-5.8.18)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) (DSR Item No-13.47.1)

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (BCD SOR Item No-5.8.32)

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (BCD SOR Item No-5.8.45)

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. (BCD SOR Item No-5.10.33)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.(BCD SOR Item No-5.3.8)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete (BCD SOR Item No-5.3.17.1)

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. (BCD SOR Item No-5.3.17.2)

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform (BCD SOR Item No-5.3.17.3)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers(BCD SOR Item No-5.3.17.5)

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts (BCD SOR Item No-5.3.17.6)

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. (BCD SOR Item No-5.6.1)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 Cement : 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size) (BCD SOR Item No-5.3.1.2)

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding , curing and taxes all complete as per building specification and direction of E/I. (BCD SOR Item No-5.8.24)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. (DSR Item No-10.16.1)

Providing designation 75A brick work in C.M (1: 4) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. (BCD SOR Item No-5.2.2)

Providing 12mm cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. & Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I. (BCD SOR Item No-5.7.2+5.7.11)

Supplying and fixing C.I. cover without frame for manholes : 560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg (DSR Item No-19.18.3)

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR Item No-19.32.1)

Cost of drilling 200 mm X 165 mm X 285 Mtrs deep bore well in all kinds of soil and rock in rural area for instillation of pump set with Hydraulic DTH rig machine, all complete including supplying all materials, tools, Drilling Rig, Air Compressor and Equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicles upto the work site. 0 to 50 M below. (DWSD Item No-M1035, Pg-57)

Cost of drilling 200 mm X 165 mm X 285 Mtrs deep bore well in all kinds of soil and rock in rural area for instillation of pump set with Hydraulic DTH rig machine, all complete including supplying all materials, tools, Drilling Rig, Air Compressor and Equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicles upto the work site. 50 to 120M below. (DWSD Item No-M1035, Pg-57)

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia (DSR Item No-23.3.3 )

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge. (DSR Item No-23.8)

Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of useable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.(DSR Item No-23.12)

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia (DSR Item No-23.13.3)

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp (DSR Item No-23.14.3)

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).200 mm dia (DSR Item No-23.15.3)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.50 mm nominal dia Pipes (DSR Item No-18.9.6)

Supplying 100mm dia submersible pump sets confirming to IS 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless pump shaft and polypropylene/ noryl impeller. Motor suitable for working on 415V+10%, 3HP, 50 Hz, A.C. supply with cable guard, thrust carbon fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitabl for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined nonreturn valve shall be provided with pump. 3 meter submersible copper conductor cable in single / double run shall be provided with each pump. 3.HP (DWSD Item No-M1055, Pg-67)

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware EWC with "p" trap of Parry Hindustan or any other LS.S. make including supplying & faxing 15 litres C. mosquito proof low down flushing cistern of approved make with complete fittings with CL handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms 15 mm P.V.C alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/cuckoo or other 1.5.5 make with Phinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc all complete as per specification and direction of Ell (A) With "P" trap (b)10 lit. low level P.V.C. cistern (DWSD Item No-3.2.2(i)b)

Supplying, fitting and fixing vitreous white glazed earthen ware L.W.C of party hindustan or any other ISS approved make with 100mm HCI p trap 15 litres Ci pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings Ci or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brass coupling and clamps Gl chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be foxed in floor 15mm Ci body brass spindle stop cock of weight not less than 50 grames 15mm PVC connection pipe 450mm long and cont of red oxide primer etc all complete as per specification and direction of E/I. (C) 580 mm long with 10 litre low level PVC cistern (DWSD Item No-3.2.1 (c))

Supplying, fitting and fixing flat back or angular lipped front vitreous white glazed earthern ware urinal of Hindustan "Parry or any other approved ISS make with 5 trs. Capacity C.l automatic fushing cistern of reliance for any other ISS approved make with all fittings with C or RS brackets standard size G.. flush pipe with fitting clamps 15mm Cl. body brass spindle stop cock of approved quality weight not less than 400 gms 15mm PVC alkethene pipe 450mm long with brass coupling at both ends and doing plumber points including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc. all complete as per speciifcification and direction of En Flat back or standing corner (600x350mm) (DWSD Item No-3.2.3)

supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or hindustan or any other ISS approved make supported on painted CIOR RS bracket 32mm Cl brass waste 15mm dia Cl body brass spindle stop cock of approved quality of weight not less than 350 grames, 32mm PVC wate pipe 750mm long with brass coupling with one end and making plumber joints etc at complete as per specification and direction of E/I. (DWSD Item No-3.2.5)

Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I (a) 20mm dia.(DWSD Item No-3.1.12)

Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I (b) 25mm dia.(DWSD Item No-3.1.12)

Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I. (c )32mm dia.(DWSD Item No-3.1.12)

Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I (d) 40mm dia(DWSD Item No-3.1.12)

Providing and Fixing brass stop cock of approved quality all complete as per specification and direction of E/I 15 mm dia (DWSD Item No-3.1.6 A(a))

Cutting chajjas or concrete for laying PVC Pipe and restoring the same with R.CC (124) brick work in cement Mortar (1:4) and cement plaster 14 as per specifiction and direction of E/i. (DWSD Item No-3.1.17)

Making holes in walls for PVC Pipe and restoring the same atfer pipe Laying (b) 250mm thick wall (DWSD Item No-3.1.18)

Cutting drain width wise above GL for laying PVC pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in C.M (14) with neat cement punning as per specifciation and direction of Ell (PVC 110mm) (DWSD Item No-3.2.10)

Making holes in wall for laying PVC pipes and restoring the same all cost complete (PVC pipe 125 mm dia) (DWSD Item No-3.2.11)

Supplying all tools and labour and cutting chajja cornice for laying PVC pipes and making good the same as per specification and direction of Ell (110mm dia PVC pipe) (DWSD Item No-3.2.9)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit) Pillar cock (long neck) (Basic rate Rs 806.50 10% for C.P & laying charge).Page 40-45 (ii)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit)Bib cock-long thread (Basic rate Rs 728.15-10% for 20v CP & laying charge)Page 40-45(iv)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit)Angular stop cock LT(Basic rate Rs 610.65+ 10% for 2) CP & laying charge)Page 40-45 (vi)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit) 4 way diverter for concealed fittings (Basic rate (vii) Rs. 2037 95 10% for CP & laying charge Page 40-45(xvii)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit) Glass shelf (Basic rate Rs.683.55 +10% for C.P & (on) laying charge Page 40-45 (xxvi)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit) 40 Flush valve complete wim 32mm sure control cock & 40-boo) Range (Basic rate Rs.3499.85 10% for CP & laying charge Pagr 40-45 (xxviii)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit)32mm dia PVC waste pipe 750mm long with cushion B (Basic rate Rs 62.40 10% for CP & laying charge. Page 40-44 (ii)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit) 15mm CP nipple with coupling(As per USR 15 basic (vo rate Rs 87.2-30% CP & laying charge) Page 40-44(vi)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit) Steel jail 100mm dia (Basic rate Rs.48.20 10% for CP.& laying charge Page 40-44(v)

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E (all rates have been adopted from the basic rate from SOR 10% for labor and Contractors profit) Providing Solvent cement (as per JSR) 168.00, 10% СРА laying charge Page 39 m-958

Supplying, fitting and foong Mirrors of 6mm thick plate (b) glass bevelled edge mirror including CP brass revolving fittings 3mm ply wood board and CP hinges to fix with mirror 600 X 450mm (DWSD Item No-3.1.21(b))

Supplying, fitting and fixing CP brass towel rail 20mm X 600mm with bracket container (DWSD Item No-3.1.21 c(i))

Supplying fitting and fixing CP brass soap dish (c) container medium quality with screw and hinges etc DWSD Item No-3.1.21 c(ii))

Providing and fixing Pressure adjustable shower with (v) revolving joint (Basic rate Rs.817.55 +10% for CP) Page 40-44 (viii)

Providing and faxing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of engineer in charge DWSD Item No-3.1.9

Supplying, materials and labour for constructing inspection chamber of designation class 758 bricks size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (16)including 12mm cement plaster (14) with punning on inside and cement plaster (16) with 800x475mm Gi cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (136) in foundation and refilling all complete as per specification and direction of E/I DWSD Item No-3.3.8

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore (DSR Item No-18.49.1)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore (DSR Item No-18.53.1)

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 gms (DSR Item No-18.75.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes (DSR Item No-18.8.2)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia Pipes(DSR Item No-18.8.3)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 32 mm nominal dia Pipes(DSR Item No-18.8.4)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal dia Pipes (DSR Item No-18.9.5)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes110 mm diameter(DSR Item No-12.41.2)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansionSingle tee with door 110x110x110 mm (DSR Item No-12.42.3.2)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Bend 87.5° 110 mm bend(DSR Item No-12.42.5)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.(DSR Item No-12.22)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank..(M079)

Point wiring in PVC conduit with Modular type switch wiring for light point/ fan point/ exhaust fan point/ call bell point/ with 1.5 sqmm FRPVC insulated copper conductor single core cable in surfface/ recessed PVC conduit with modular type switch modular plate suitable of Ol box etc as required Group-c E SOR Item No-1.3.3

Supplying and Fixing light plug point with Modular Type accessories Supply and Fixing GI Box with modular pplate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 Amp modular socket outlet and 5/6 amps modular type switch connection painting etc as required.E SOR Item No-1.31

Supplying and Fixing light plug point with Modular Type accessories Supply and Fixing GI Box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 Amp modular socket outlet and 5/6 amps modular type switch connection painting etc as required.Ele SOR Item No-1.32

Supplying and fixing 20amp 240v SPN industrial type socket outlet, with 2 pole and earth metal enclosed plug top alongwith 20amps, G-series, SP MCB,in sheet steel enclosure on surface or in recess, with chained metal cover for the socket outlet, and complete with connections, testing and commissioning etc as requried Ele SOR Item No-2.18

Wiring for light/power plug with 2x 4 sq.mm FR PVC insulated, copper conductor single core cable in and surface/recessed PVC conduitalong with No. 4 sq mm FR PVC insulated copper conductor single core cable for loop earthing as requried E SOR Item No-1.5

Wiring for circuit/sub main wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required 2x1.5 sq.mm + 1x 1.5 sq.mm earth wire E SOR Item No-1.7.1

Wiring for circuit/sub main wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required 2x2.5x sq.mm +1 x 2.5 sq. mm Earth wire E SOR Item No-1.7.2

Wiring for circuit/sub main wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required 2x 6 sq.mm +1x6 sq.mm Earth Wire E SOR Item No-1.7.1

Wiring for circuit/sub main wiring alongwith earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required4 x 10 sq.mm + 2x 10 sq.mm E SOR Item No-1.7.11

S/F tP MCB DB Supplying and fixing following way three pole and neutral sheet MCB distribution board 415 voits on surface/recess complete with tinned copper busbar neutral busbar earth bar din bar detachable gland plate, interconnection phosphatized and powder painted including earthing etc as required (but without MCB/RCCB/Isolator) 4 Way (4+12 Ways) Dpouble Door E SOR Item No-2.9.4

S/F C series SP MCB Supplying and fixing 240 volts C series miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections testing and commissioning etc 6/32 A Singal Pole E SOR Item No-2.12.1

S/F C series SP MCB Supplying and fixing 240 volts C series miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections testing and commissioning etc 32 A TPN MCB E SOR Item No-2.12.8

S/F C series SP MCB Supplying and fixing 240 volts C series miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections testing and commissioning etc 50/63 A TPN MCB E SOR Item No-2.12.10

S/F Ceiling Rose Supplying and fixing 2 pin orilting Rose on the existing junction box wooden block including connection etc as required E SOR Item No-1.33

Supplying and Fixing Batten holder Supplying and fixing Batten/Angle holder including connection etc required E SOR Item No-1.34

ITC lucrevent Bitting directaly on surface installation testing and commissioning of pre wired Guorescent fisting/compact fluorescent fitting of all type complete with all 1.41 accessiories and tube etc directaly on criling wall including connection with 1.5 Sq mmi FR PVC insulated copper cond E SOR Item No-1.41

ITC: Ceiling fan installation testing and commission seiling fan including wiring the down rods standerd lenght (Up to 30 cm) with 1.5 Sq mm FR PVC Insulated copper cond, single core cable etc as required E SOR Item No-1.44

125 S/F Moduler type electronic fan regulator E SOR Item No-1.25

ITC Exhoust fan upto 450mm sweep insallation and exhaust fan upto 450mm sweep in the exinating opening 1.48 including making the hale to cut the size of the above fan making good the damage including connection testing commissioning etc as required E SOR Item No-1.48

Suppyling and drawing following pair,0.5sq mm FR PVC insulated copper conductor unarmoured telephone cable in the existing surface / recessed steel/ PVC conduit as reqd. 2 Pair E SOR Item No-1.16.2

Suppling and fring following moduler type switch /1.24 socket on the existing switch box cover including connection etc. as reqd.Telephone socket outlet E SOR Item No-1.24.6

Double LED tubelight fifting made of Die cast aluminium housing 2 x 20 watt bettal tubelieht suitable for surface mounted E SOR Item No-M1555

providing fitting fixing & testing of (Esential) CFL Lamp 18/20 W CFL in exinsting batten/angel holder (Make-philips/bjaj/cromptown/wipro)E SOR Item No-M-870

Supply of recess mounting 600mmx600mm -luminaires 2X36 E SOR Item No- M-841

Supply of 1400mm Sweep, double ball-bearing, 2 canopy ceiling fan without regulator including connection with 1.5 sq mm copper wire, down rod all accessori E SOR Item No-M-773

450 mm (18") metal body wall fan with speed regulator suitable for sfuncle phase 220Y, 50H2 AC supply E SOR Item No-M-1918

Supply of AC 230/250 Volts, 50Hz, 380mm sweep/900 rpm Exhaust Heavy Duty Fans (Double Ball) including providing nuts- bolts, mounting frame and other required accessories etc. Make- Havells-Turbo Force/Bajaj-70069/ Crompton Greaves EXHD300-4-1E SOR Item No-M-776

GI Earth Pipe Electrode Barthing with Gl earth pipe 45 mtr long 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe elc (but without charcol or coke and salt) complete as required.E SOR Item No-3.1

Earthing with G.I. earth pipe 4.5 intr long 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required. E SOR Item No-3.2

Providing and Fixing 25mm x 5 mm O Earth Strip In Ground. Providing & fixing of 25mm x 5mm Gl Strip at 0.5 metre below ground as strip earth electrode, including soldering etc as required E SOR Item No-3.10

Providing and Fixing 25mm x 5 mm GI Earth Strip in Pipe Providing & fixing of 25mmx5mm Gl Strip for Fixing in Gi Pipe from earth electrode as required E SOR Item No-3.14

Basic Provioding and laying 11 KV grade aluminium armoured cable as per 18 1554 (Part 1) heavy duty all cost complete for including cost of brass compression gland, cable jointing & and end termination as per specification and direction of 3 & half core 25 sq.mm E SOR Item No-M 326 ( Basic rate + 14.99% for Layong & C.P)

Basic Provioding and laying 11 KV grade aluminium armoured cable as per 18 1554 (Part 1) heavy duty all cost complete for including cost of brass compression gland, cable jointing & and end termination as per specification and direction of 3 & half core 50 sq.mm E SOR Item No-M 328 ( Basic rate + 14.99 % for Layong & C.P)

Basic Provioding and laying 11 KV grade aluminium armoured cable as per 18 1554 (Part 1) heavy duty all cost complete for including cost of brass compression gland, cable jointing & and end termination as per specification and direction of 3.5 core 95 Sq mm E SOR Item No-M 330 ( Basic rate + 14.99% for Layong & C.P)

Cairrage of Material Cement + Steel

Stone Chips

Bricksn( in Thousand)

Add 18 % GST

Add 1 % L.C

Please Enable Macros to View BoQ information