General Fund

Drilling of Bore well by down the hole hammer drilling to a finished dia of 112/165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to timeDrilling of Bore well 165 mm dia. up to 90.00 m depth

Geogagalist survey charges report for plain areas

supply delivery and erection of 175mm dia oD Pvc casing 6kg/cm2 casing pipe of 6mt length including cost and conveyance of all charges

Supply and Transportation of 5.00HP, 12-16 Stage,5star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with waterproof winding, Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415V ± 10%, Three Phase 50 Hz AC supply etc complete for 6" Bore well. Makes: category I.Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/ ARYEN VARSHA /Falcon/Prithvi

Fabrication ,transportation and and supply of wall mounted control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side louvres with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using LAURITZ KNUDSEN (FORMERLY L&T) / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor pump sets. a)Voltmeter ; 0-500 V 96x96mm size.Makes: Lauritz Knudsen (formerly L&T) / C&S / SALZAR / HPL/ AEI / Meco / Rishab . b)0 to 20 Amps / 0 50 Amps Ammeter (96x96mm size)-1No.Makes: Lauritz Knudsen (formerly L&T)/ C&S / SALZAR / HPL/ AEI / Meco / Rishab c)Single phase preventor of suitable range - 1No.Makes: Lauritz Knudsen (formerly L&T) / Minilec / Powertec d)32 A TP, 10KA MCB. - 1No Makes: Legrand / Schneider capacitor e)Indication lamps (R-Y-B) with switch control - 1set f)Voltmeter & Ammeter selector switch - 2 Nos g)Supply and fixing of ISI Mark suitable capacitor Makes: Lauritz Knudsen (formerly L&T) / Siemens / Schneider / Epcos/Havells.. h) Upto 7.5 HP with DOL Starter of.Make C&S.Crompton / Lauritz Knudsen (formerly L&T) /KSP/ Siemens/BCH.

Supply and delivery of 60MM UPVC Pipe for submersible motors with both ends square threaded, with rubber 'O' rings with smooth inner surface which can take the minimum load of 2100 to 4000 Kgs weights. Makes: As per list of recommended brands. 60/50 mm UPVC pipe with standing upto 20 Kgs / CM2 upto 200 Mts

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH 110mm 6kg/cm2

Providing bedding with sand for foundation trenches as per specification and drawing including cost and conveyance of materials to site with all leads, lifts including watering, tamping, ramming, labour charges, all other incidental and operational charges etc., complete as per detailed specification and directed by the Engineer - in - Charge (as per SSR 25-26- Amendment)110mm 6kg/cm2

Manufacture, Supply, & Delivery of HDPE pipes conforming to IS 4984 - 2016 including transportation to anywhere in A.P, excluding all taxes (Supply up to 90 mm dia. in coil & above 90 mm dia. straight Length) specification in light Grey/Natural Ivory Grey/ Any other Color (except White) inclusive of transportation to the sub-divisional stores anywhere in AP excluding all taxes.110mm 6kg/cm2

Laying and jointing of HDPE pipes by butt fusion welding as per IS:7634-Part-II/1975 as amended from time to time to the alignment and gradient and testing the pipe line to the required pressure including sales tax but excluding specials etc., including VAT and Labour cess and excluding CED and Service Tax 110mm dia