SPL REPAIR TO TOILET OF SERVANT QTR NEAR BLDG NO EW29 IN TONS VIEW SPL REPAIR TO TOILETS NEAR GRAND STAND 1 3 ACC WG AND IMA CSD SPL REPAIR TO VENTILATOR FROM BUNGALOW NO P1 TO P19 AND PROVN OF 200 X 5AMP IND POINT IN GC CABIN OF TH BN AT IMA DEHRADU

Amount

Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m deep in soft/loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggt) as in foundation, Sub base filling and mass concrete etc complete all as specified and directed.

Dismatling of brick work built in cement mortar complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, old size, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:6.complete all as specified and directed.

M&L for 40mm thick Damp proof course horizontal surfaces including necessary form work in PCC 1 : 2 : 4 type B-0 (using 12.50 mm graded crushed stone agg),complete all as specified and directed.

M&L for RCC (nominal mix) 1 : 2 : 4 type B-1(using 20 mm graded crushed stone aggregate), as in slab supported on walls complete all as specified and directed.

Use and waste of form work sides and soffits of beams , lintels, shelves including support overhang. flat for rough finished surface, complete all as specified and directed.

Use and waste of form work to sides and soffit of slab supported on walls , shelves exc 10 cm but not exceeding 20 Cm thick flat for rough finished surfacecomplete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and directed.

All as par Ser item No.9 above 6 to 8 mm dia TMT Bars.

Taking down cement plaster on brick or stone walling built in cement mortar including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4, mixed with water proofing compound as per manufacturers instructions, finished fair and even as directed. ( water proofing compound shall be measured and paid separately).

M & L for rendering 15 mm thick in cement mortar (1:6) using coarse sand on brick or concrete surface finish even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:3 finished fair and even on ceiling and sides of slab complete all as specified and directed.

M&L for rendering 15 mm thick on concrete surface of roof slab as grouting in cement mortar 1:3, mixed with water proofing compound,as per manufacturers instructions,finished even & smooth on roof surface finished complet all as specified. ( water proofing compound shall be measured and paid separately).

Supply only Liquid water proofing compound.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, laid in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with and including laying of 20 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area n exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area exc 1.50 Sqm and n exc 4.00 sqm each complete all as specified and directed.

Taking down shutters only of size exc.1 Sqm and n.exc 2 Sqm each, complete all as specified and directed.

S & F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube & edges will be painted to match with printed sheets complete all as specified and directed.

S & F Factory made solid panel PVC shutter 30mm thick(style) consisting of frame made out of MS tubes for top & bottom rails ms frame shall be covered with heat moulded plain colour PVC "C" channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification & drawing in SSR Part II 2010 etc complete all as directed.

S & F Steel ventilators box type with centre hung shutter including hinges, steel peg stay, complete all as specified.

S & F Steel windows box type with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars dovetailed or welded incl cutting holes in wall for inserting holdfast and making good to the dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required, complete all as specified.

S&F Stainless steel Butt hinges, 100mm long, medium weight, complete all as directed. Make- Aluminium Udyog New Delhi(Brand- Global)/Mohan Matel Industries(Brand- Crown)/Urgent Industries New Delhi.

S&F 150mm long aluminium anodized handle cast type, complete all as directed.Make- Aluminium Udyog New Delhi(Brand- Global)/Mohan Matel Industries(Brand- Crown)/Urgent Industries New Delhi.

S&F 200mm long aluminium anodized barrel tower bolt of extruded section complete all as directed. Make- Aluminium Udyog New Delhi(Brand- Global)/Mohan Matel Industries(Brand- Crown)/Urgent Industries New Delhi.

S&F 250mm long aluminium anosized sliding door bolt with hasp staple (bolt type) and fixing clips to sheet cast or extruded section of cast aluminium complete all as directed.Make- Aluminium Udyog New Delhi(Brand- Global)/Mohan Matel Industries(Brand- Crown)/Urgent Industries New Delhi.

M&L for hard core of broken stone gauge n.exc 63mm, complete, all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate), as sub base of floor complete all as specified.

M&L for 75mm th PCC 1:3:6 type C-2(using 40mm graded crushed stone aggregate), as in plinth protection and paving, finished even and fair complete all as specified.

M & L for rubberised polished colored heavy duty 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete, all as specified and directed. Make:- Tulip infrastructure saharanpur, Mehtab tiles, NTC tiles Panchkula

Returning, filling in, including spreading, leveling, watering and well ramming n.exc 25cm layer complete all as specified and directed.

Removal surplus soil to a distance n. exc. 50 meters and depositing where directed at a level n. exc 1.5 meter above the starting point complete all as specified and directed.

S&F figured glass, pin head type, 3mm thick and glazing with oil putty in squares n.exc. 0.5 Sqm each pane, complete all as specified.

S&F Bib Taps, cast copper alloy, fancy type, chromium plated, long body with capstan head, screwed down, screwed for 15mm bore GI pipe or brass ferrule or to GI socket complete all as specified and directed .Make- Jaquar Essco (Orbit series)/ Cera(Victor series)/Kajaria Kerovit (JOY series).

Dismantling water tank and removing to store.exc 500 &nexc1000 ltrs complete all as specified and directed.

S & F 500 ltr capacity Rotational moulded polythylene water storage tanks three layered, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR Part -I, complete all as specified and as directed.

S & F 1000 ltr capacity Rotational moulded polythylene water storage tanks three layered, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR Part -I, complete all as specified and as directed.

S & F Ball valve 20mm dia high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball min weight 210 gms fixed in repair complete all as directed. Make: Prayag/Pollytuff/Syentex.

S&F CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and as directed.

S&F Shelf of PTMT fixed with and including CP brass screws and wooden or plastic cleats, all as directed.

S&F Aluminium hat pegs, solid body, 125mm to 175mm fixed with screws all as directed.

S & F 20mm bore gun metal globe/gate valves, with iron wheel head, screwed both ends for iron/GI pipe fixed in repair complete all as directed. Make: Zoloto/Leader/Kirloskar.

Taking up or down GI tubing and connection 15 mm bore of pipe or removal to store, complete all as directed.

Taking up or down GI tubing and connection 20 mm bore of pipe or removal to store, complete all as directed.

S & F 20mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc, complete all as directed.

S & F 15mm bore medium grade steel water tubing, galvanized (ISI Marked) with and including all fittings (ISI Marked) and jointed, tested and fixed complete to wall and ceiling or laid in floors etc, complete all as directed.

S&F 75mm dia PVC(SWR) pipe laid in trenches or fixed to wall etc. complete all as specified and directed.

S&F PVC (SWR) bends 75mm dia, complete all as specified and directed.

S&F 75mm dia PVC(SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, fixed to walls/floors fixed in repairs, complete all as specified and directed.

S&F PVC branch pieces single ordinary or inverted or with parallel branches 110mm dia fitted with oval access doors fixed in repairs complete all as specified and directed.

S&F PVC bends fitted with oval access doors 110 mm dia any radius diminishing pieces or tapers fixed in repairs complete all as specified and directed.

S&F PVC (SWR) floor trap 100mm dia, plain with grating including jointing with solvent cement fixed in repairs complete all as specified and directed.

S&F PVC branch pieces single ordinary or inverted or with parallel branches 75 mm dia fitted with oval access doors fixed in repairs complete all as specified and directed.

S&F Chromium Plated fancy type angle valve 15mm dia (angle cock) fixed in repairs, complete all as directed. Make- Jaquar Essco (Orbit series)/ Cera(Victor series)/Kajaria Kerovit (JOY series).

S&F Chromium Plated fancy type, 15mm bore pillar cock Rocket type with areator fixed in repairs, complete all as directed.

S&F PVC conections 15mm size with PTMT nuts of 600 mm long fixed in repairs complete all as specified and directed.

S&F PVC low level flushing cistern 10 Ltr capacity symphonic action type white with ball valve float valve and handle incl bracket complete all as specified and directed. Make : Parryware/Cera/Hindware.

S&F Vitreous china squatting pattern Orissa pattern water closet pan of size 580 x 440 mm white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.Make : Parryware/Cera/Hindware.

S&F Vitreous china wash basin, white, flat back, size 550x400mm including bracket complete all as directed.Parryware/Cera/Hindware.

M&L for PCC 1:2:4 type B-2(using 40mm graded crushed stone aggregate), as in surface channels and drains of any description complete all as specified and directed.

Extra for forming fair finished drain or channel 30 Cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

M&L for Salt-glazed stoneware drain pipes grade 'A' 150mm dia laid in trenches and jointed complete all as specified and directed.

M&L for PCC 1:3:6 type C-2(using 40mm graded crushed stone aggregate) for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested suitable for 150mm bore of pipe complete all as specified and directed.

M&L for construction of soakage well of size 3.60m dia X 3.00m effective depth, excavation in any type of soil, foundation in PCC 1:3:6 type C-2, walls of honey combed and solid in M-25 (design mix) concrete, including intercepting chamber, screen chamber, brick work in cement mortar 1:4, plaster where shown on drg shall be 12mm thick in cement mortar 1:6, bearing plaster 15mm thick in cement mortar 1:4, RCC cover slab In M-25, filling with brick bats of gauge 80 to 150mm complete all as specified and shown Drg No.TD-309 sheet 1/4 to 4/4.

M&L for Precast RCC 1:2:4 Type B-1( using 20 mm graded crushed stone aggregate} as in cover slab, set and jointed in cement mortar 1:4 incl demolition of existing old RCC slabs of any description complete all as specified and directed. (Note: Reinforcement shall be measured and paid separately under respective items of this BOQ)

Supply and fixing factory made 30mm thick 100% soild WPC Window glazed shutter / wire mesh shutter 95 mm x 30 mm thick. Made from WPC material with density not less than 800 Kg/Cum. All four corner are fusion welded & scrwed with 8 x 50 mm self - screws for additional strength. After joining all 4 corner clear space to be paneled with 5mm thick glass / S S mosquito mesh after glazing of in side of shutter 10 x12mm pvc "L"shape bead to be nailed or sticked with shutter. Provided 2 Nos SS hinges of 100mm, 1 Nosaluminium handle of 125mm, 2 Nos aluminium tower bolt of 125mm and 01 peg stay for each shutter ( Glazed and Gauzed ) incl factory made 100% solid WPC ventilator frame 125 mm x 65mm double rebated frame & mullion 125 x 80mm. made from WPC ( Single extruded process) material comparising of virgin PVC polymer of K value 57-60 ( Suspension grade), calcium carbonate and natural fibers (wood powder/ rice/ husk/wheat husk),and nontoxic additives fabrioated with meter joints after applying PVC solvent cement & screwed with fully body treated star headed screws having minimum frame desity not less than 800 Kg / cum, having good screw holding capacity ( screw withdrawal strength of (min 990N ). Minimum compressive strength of 58 N/mm2. Modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof,water / mosquired prrof & fire retardand & fixed in position with fasteners/ hold fast of required size. window shall be provided with MS Grill/Guard bar made of 10mm MS Sq bar welded to 6x20mm MS flat including painting with countersunk holes at both vertical ends. Gap between the bars should not be more than 125mm. All as per specification as directed by Enger-in -charge Note - (i) Galzed and Gauzed shutter both are deemed in this quoted rate (ii) Glass pane, wire mesh and grill are deemed in this quoted rate Make:- M/S Rajshree Plastiwood Ltd. Indore-452001 M/S Ecocell (Kumar Arch Teck) (N Gujrat)-382721 Navratan Speciality Chemicals LLP Ahmedabad Alstone Ind Pvt Ltd

M&L for Cement mortar 1:4 forming jambs,etc., to openings (to foregoing item), with including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work, complete all as specified and directed.

Dismantling of corrugated AC sheet any pattern in roof incl ridge complete all as specified and directed.

S& F Pre- painted galvalume aluminum zinc coating GI based tile profile corrugated steel sheet 0.50mm to 0.60mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified having cap with rubber and metal washer complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description, complete all as specified and directed.

S&F Structural steel, rolled section as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe-410 W (Gde-E-250)all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, complete all as specified and directed.

Supply and fixing false ceiling at all heights with GRG (Glass Fiber Reinforced Gypsum) false ciling tiles of Seze 595x595 mm of approved texture, design and patterns having moisture content less than 2% humidity resistance of 99%, NRC 0.50 to 0.75 as per IS 8225 :1987, Noncombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 00.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32mm of length 3000mm , cross-T of size 15x32mm of length 1200mm and secondary intermediate cross-T of szie 15x32mm of length 600mm to form grid module of size 600 x600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8 mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod up to 1000mm length and L-shape level adjuster of size 85x25x2mm. Galvanized iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-In-Charge. with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles. Make:-Diamod International Inex Pvt Ltd (Brand Diamon ceiling), PR Ceiling Product Ltd, Visaka Indusries Ltd

Taking down existing roof treatment from the RCC slab, cleaning off all foreign material by wire brushing clenaing off surfce including demolition of cement concrete (Unreinforced) over Roofs of any thickness and removal of spoil to a distance n.exc. 500 mtr complete all as directed.

M&L for providing cement concrete in roof kerbs or mud stops, rounded or chamfered as in 1:2:4 type B-0 (using12.50mm graded crushed stone aggregate), complete all as specified.

M&L for 10 mm thick screed bed in cement mortar (1:4) over concrete surface finished even & smooth without using extra cement mixed with water proofing compound as per manufacturer's instructions while the concrete is green, complete all as specified.( water proofing compound shall be measured and paid separately).

M & L for Roof treatment by applying a coat of cold applied oil based bituminous primer over cleaned surface @ 0.50Kg/Sqm, and laid 3mm thick APP modified five layer polymeric membrane , minimum weight not less then 3.60 kg/Sqm reinforced with polyester non-woven fabric (weighing not less than 150 gms/sqm) with torch application method as per manufacturer's instructions with side over lap of 75mm & end over lap of 100mm & tucked into the chases on vertical surfaces with grooves & make good in cement mortar 1:3, finally finished with bituminous aluminum paint @ 0.20 Kg/Sqm etc complete including taking down existing roof treatment of the RCC slab, cleaning off all foreign materials by wire brushing, cleaning roof surfaces with water and removal of spoil out side the defence premises, complete all as specified and directed. Make : STP / Sika/ Fosroc as approved by GE. Note :- Work shall be executed by authorised applicator of manufacturer and upto roof height of triple storied building. 10 years manufacturer guarantee shall be submitted by the contractor.

Demolition of cement concrete ground floor and paving n.exc 15 Cm thick below or above ground level complete all as specified.

M&L for 50 mm thick cement concrete 1:2:4 type B-2 (using 20mm graded crushed stone aggregate), as in hard standing including finshing the surface by brooming complete all as specified.

Dismantling Floor,hearth or wall tiles including cement mortar bedding but not backing) complete all as specified.

M & L for Non skid ceremic colour joint free tile 7.00 to 8.00 mm thick (square/rectungular) area exceeding 0.18 sqm but not exceeding 0.38 Sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of 15 mm thick in cement mortar 1:6, complete all as specified and directed.

M & L for Vitrified exterior colour tile (parking tiles) of size 30 Cm x 30 Cm x 9 mm thick, set, jointed and pointed in neat cement slurry in floors with white cement and pigments to match over and including screed bed or bedding layer or mortar 15 mm thick in cement mortar 1:6, complete all as specified and directed.

M & L for chequered heavy duty polished colored cement tiles 30 Cm x 30 Cm X 20 to 25 mm thick, set, jointed & pointed in neat cement slurry in floor with grey cement mixed with colour pigments complete all as spd. & directed. Make:- Tulip infrastructure saharanpur, Mehtab tiles, NTC tiles Panchkula

M & L for 20 mm thick scred bed or bedding layer of cement mortar 1:6 for laying of flooring complete all as specified and directed.

S & F in repairs vitreous China wash down water closet pan (Pedestal Pattern) white with plastic water closet seat, black, closed pattern with recessed bottom, and cover mild steel chromium plated or aluminised hinging deviceincluding connection to trap, and to flushing pipe, anti-syphonage pipe, etc Complete all as specified. Make : Parryware/Cera/Hindware.

S&F in repairs oval shaped coloured vitreous china WHB snow white, fancy type of overall size 595 x 380mm, Cat No 7751 of Cera or of equivalent make specified here-in-after including 32mm CP waste coupling, PVC waste pipe, including fixing arrangement as per site requirement, complete all as directed.

S&F in repairs PTMT grating 100mm dia with hole for waster, complete all as specified.

S&F in repairs Low density polythene pipe (LDPE) of pressure rating 6 Kg per Sq.cm, 450mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe, complete all as specified.

Demolition of reinforced cement concrete as in any description and I any position all as specified

M & L for Precast reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) for manhole cover slabs, set in cement mortar 1:6, including necessary form work moulds etc all as specified. (Reinforcement shall be measured and paid for separately).

M&L for PCC 1:3:6 type C-2(using 40mm graded crushed stone aggregate) for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested suitable for 100mm bore of pipe complete all as specified and directed.

S & F PVC (SWR) junction single (Tee) 75mm bore equal or unequal with access door complete all as specified and directed.

S & F PVC (SWR) junction single (Tee) 110 mm bore equal or unequal with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore in repairs complete all as specified and directed.

S & F in repairs Vitreous China Urinal, Half stall type,white (excluding flushing cistern) , flush pipe and waste pipe with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. all as specified and directed.

S & F in repairs Vitreous China Urinal, full stall type,white (excluding flushing cistern) , flush pipe and waste pipe with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. all as specified and directed.

Demolition and breaking up drain 100 mm dia pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, all as specified and directed.

S&F in repairs galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples, all as specified and directed.

S&F in repairs soap dish, vitreous China white, approximate size 160x 160x90mm, all as specified and directed.

S&F in repairs toilet paper holder, vitreous China, box type coloured, all as specified and directed.

S & F in repairs Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), all as specified and directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as directed.

M & L for providing groove and drop at the bottom edge of RCC roof slab. Groove shall be 40 mm wide x 20 mm deep and droop shall be 25 mm wide and 20 mm rise, casting, finished with cement mortar 1:3 all as directed at site by Engineer-in-Charge.

M & L for Prepration of scrapped surface of wall / ceilling and applying 1.00 to 1.50mm thick Asian acrylic damp proof wall care putty in two coats as per manufactur's instructions, complete all as specified and directed.

M & L for Prepration of surfaces of wall / ceiling and applying two coats of oil bound emulsion distemper over a coat of primer complete all as specified and directed.

M & L for Prepration of primed surfaces of wall / ceiling and applying one coats of Appex paint ( Weather coat exterior paint) complete all as specified and directed.

M & L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in cill , copings and other similar wk etc including necessary form work complete all as specified and directed.

Preparation of new plastered surfaces and applying three coats of white wash on walls, complete all as specified and directed.

M&L preparing new or previously untreated surface of wall and applying two coats of cement based paint over a coat of primer .

Preparation of new plastered surfaces and applying three coats of white wash ceiling, complete all as specified and directed.

M & L for complete removal of existing treatment on old decorated surfaces (plastered/un-plastered) on walls including cornices on plastered surfaces,and applying wall putty 1.00 to 1.50mm smooth finish, and all as directed.

M & L for Preparation new steel surfaces exc. 10 cm width or girth and applying two coats of synthetic enemelled paint over one coat red oxide promer complete all as specified and directed.

M & L for Preparation of surface of wood width or girth over 10 sqcm area exceeding 10 sqcm and applying two coat of synthetic enamel paint over one coat of pink primer including preparation of suraface

M & L for Preparation old steel surfaces exc. 10 cm width or girth and applying One coat of synthetic enemelled paint including all preparation complete all as specified and directed.

Supply and fix Socket outlet, multipurpose, 2 in 1, 5 pin, 5 Amp complete all specified and as directed Make:- Anchor/Legrand/Havells/C&S.

Taking down carefully existing aluminum/copper surface/concealed point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, etc and making good the disturbed surfaces in CM 1:3 of walls, floors, ceiling etc including distempering to match with existing surfaces complete all as specified and directed.

Taking down existing ceiling fan of any capacity and make service the fan by replacing the unsv part and preparation of old painted surface body and blades of ceiling fan of any capacity ,cleaning foreign material ,filling cavaties atc and painting with one coat of synthetic enammeled paint by spray painting and marking MES No. with paint and kept in safe custody for reuse at site after compltion of wiring work.

Taking down old Unsv MCCB DB/MCB DB including MCB,s ,Metal Socket of any size /capacity etc and making good the disturbed surfaces in cement mortar 1:3 of walls, floors, ceiling etc including distempering to match with existing surfaces complete all as specified and directed.

Taking down old unsv T/L fitting, lamp holder ,security light fitting of any capacity.

Material and labour for point wiring with PVC insulated and unsheathed electric able 1100 volts grade single core FRLSH having multi stranded copper conductor of 1.5 sq mm nominal cross sectional area drawn in and including concealed non metallic rigid PVC conduit not less than 20 mm dia with all fitting and fixing accessories and 1.5 sq mm PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes 1.6 mm thick, 60 mm deep of required size factory made for mounting switch, regulators etc with and including 3 mm thick plastic hylam laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches, sockets etc complete for the following. Make of wire: Havells, Polycab,Gloster. Make of conduit: AKG, Polycab,Finolex Note: (i) The quoted rates shall be deemed to be inclusive for cutting chasing in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using PVC rawl plugs Where not feasible to draw cable in concealed . (ii) Point wiring & earth wire shall be connected to each & every sunken box. (iii) All screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates.

One light point controlled by one, one way 6 Amp switch

One fan/exhaust fan point controlled by one, one way 6 Amp switch

S & F switch piano, flush type, single pole one way, 5/6 Amp complete all as directed. Make: Anchor (Penta PC), Havells (Reo)

S&F ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate/isolated body complete all as directed. Make: Anchor (Penta PC), Havells (Reo)

S & F MCB DB,s double door SPN with 200 Amps rated copper bus bar with neutral bar,earth bar,cable ties for cable management, fully shrouded neutral bars ,reversible door, 240 volts with blanking plates where required and IP 43 DB,s degree protection of following capacity complete all as directed:-

4 way SPN DB.Make :Legrand L&T, ABB, Schneider,

8 way SPN DB.Make :Legrand L&T, ABB, Schneider,

S & F in repairs MCB 240 volts 'B' Curve 10 KA, including connection with suitable size copper lugs including taking down old unsv MCB,s for following Rating /capacity complete all as directed:- Make: Legrand, equvilent in L&T, ABB, Schneider

MCB SP6 to 32 Amp.240 volts

MCB SPN 40 to 63 Amps 240 volts

Supply and Fixing in repair LED Batten light fittings on walls including brackets all as conforming to the following parameters including taking down old unsv Light fitting: - (i) Syatem watt/Lumens: - Max-22 watts/total system lumen not less than 2200 lm (ii) Housing: - High pressure die cast aluminium. (iii) IP Rating: - IP 20 (v) Mounting: - Wall Mounted (vi) Finish: - Polycarbonated diffuser (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100 lm/watt. (ix) Colour temperature (K): - Not less than 5700( COOL DAY LIGHT) (x) Color Rendering Index (CRI): - Not less than 80 (xi) Life: - Not less than 20000 Hrs of operation (xii) Optics: - Fully Diffused (xiii) Control gear: - inbuilt electronic driver, PF not less than 0.90 and THD less than 20 % with operating voltage 140-270V AC, 50 Hz (xiv) Surge protection: - inbuilt surge protection minimum 2.5KV (xv) Heat Shink: - As per OEM's design (xvi) Bidder has to compulsorily submit the data sheets conforming of technical spscifications. Make: - PHILIPS /EVEREADY/WIPRO/HAVELLS

Supply and Fixing LED street/Security light fittings on poles/Wall including mounting brackets all as conforming to the following parameters including taking down old unsv Light fitting : - (i) Syatem watt/Lumens: - Max-25 watts/total system lumen not less than 3000 lm (ii) Housing: - Single Piece High pressure die cast aluminium. (iii) IP Rating & IK Rating: - IP 66 & IK07 (iv) Front cover: - Polycarbonated Cover for More protection (v) Mounting: - Suitable for pole mounting with bracket arm 40-50mm dia, Mounting height- 5.50m to 6.50 m from GL. (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED with Lens (viii) System Efficacy (lm/W) of the luminaries: - Not less than 120 lm/watt. (ix) Colour temperature (K): - Not less than 5700 (x) Color Rendering Index (CRI): - Not less than 70 (xi) Life: - Not less than 50000 Hrs of operation @ Ta 35*C (xii) Optics: - Spread (Beam angle along the driveway) - 120°, Through (Beam angle across the driveway)- 60°, Beam pattarn- Asymmetrical driveway. (xiii) Control gear: - inbuilt electronic driver with 325V Auto Cut off Restart feature & 440V Phase to Phase protection till 8 hour, PF not less than 0.95 and THD less than 10% at full load with operating voltage 140-270V AC, 50 Hz. (xiv) Surge protection: - inbuilt surge protection minimum 4KV. (xv) Heat Shink: - As per OEM's design (xvi) Bidder has to compulsorily submit the LM-79 and LM-80 and third party NABL accredited lab test report conforming of technical spscifications and consolidated lab report for the offered LED has to be stractured in the same sequence.Also submit BIS of Luminair and drivers Make: - Make: - PHILIPS /EVEREADY/WIPRO/HAVELLS

Supply and fix exhaust Fan ,steel body ,AC Single phase , voltage 230volts, 50HZ, copper winding of sweep 300mm with louvers, including cutting holes on wall and making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface, complete all as directed.

Taking out old Unsv LT UG cable of any size , complete all as directed. Note:- Excavation shall be measured and paid separately.

Taking out old Unsv service wire of any size, complete all as directed.

Supply, laying and testing XLPE cable Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core, complete all as directed. Make:- Havells, Polycab,Gloster,Grandlay, Gemscab.

M&L for sand cushioning to UG cables (8 Cm deep before laying of cable and 15Cm deep over the cable), complete all as directed. Note : Punned thickness will be measured.

Suppy and laying un-reinforced precast cement cable cover, class LV, type -I flat size 250x150x40mm complete all as directed. Make:- Tulip infrastructure saharanpur, Mehtab tiles, NTC tiles Panchkula

Supply and laying Tube light grade galvanised 50mm dia with all fittings, laid in ground for crossing the cables across the road by cutting existing road and making good the road surface after laying of pipe, complete all as directed.

Material and labour for earthing with galvanised steel earth plate electrode 60cmX60cmX 6mm thick burried directly in ground (earth pit not less than2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm thick GI wire by means of nuts,bolts,check nuts & washers of galvanized iron or steel,protected by 15mm bore light grade galvanised iron pipe and connected to main switch board,including all necessary excavation & earth work in hard dense soill including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternate layers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover10mm thick hinged to CI frame and 6mm MS rod for handle and necessary testing complete all as shown in electrical plate No 3 of SSR part-I (2009) all as specified and directed.(Two earthing for each main Panel )

S&F 200mm long stainless steel barrel tower bolt bolts, complete all as directed.Make- Aluminium Udyog New Delhi(Brand- Global)/Mohan Matel Industries(Brand- Crown)/Urgent Industries New Delhi.

S&F 150mm long stainless steel handle, complete all as directed.Make- Aluminium Udyog New Delhi(Brand- Global)/Mohan Matel Industries(Brand- Crown)/Urgent Industries New Delhi.

S&F 250mm long stainless steel sliding door bolt with hasp staple (bolt type) and fixing clips to sheet cast or extruded section of cast aluminium complete all as directed.Make- Aluminium Udyog New Delhi(Brand- Global)/Mohan Matel Industries(Brand- Crown)/Urgent Industries New Delhi.

M & L for glazed ceramic coloured joint free tiles 300x450x7mm thick as in vertical surfaces including 10 mm thick rendering in cement mortar 1:4 and set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles, complete all as directed.

M & L for preparation of new plastered or unplastered surfaces and applying two coats of Appex paint over a coat of cement primer on wall, complete all as directed.

Hacking out old broken glass (any thcikness size, quality or descritpion) from wooden frame or steel frame glazed with putty or fixed with beads exc 1.5 sqm, complete all as directed.

S & F 3mm thick sheet glass, ordinary quality in square nexc 0.50sqm each pane glazed with oil putty or fixed with wooden beads, complete all as directed.

M & L for fixing only 20 mm tubes including new ISI marked fittings to walls and ceilings or laying in floors, complete all as directed.

S & F One 03 Pin 05 Amp switch socket out let point controlled by one independent board complete all as specified.

M/S S P BUILDERS

M/s RK ENTERPRISES

ACE BUILDERS AND CONTRACTORS

Aggrawal Builders and Furnishers

M/S RAJESH KUMAR GOYAL