REPAIR, STRENGTHENING AND RENOVATION OF EXISTING CANTEEN BLOCK FOR HANSRAJ COLLEGE, DELHI

Amount

D I S M A N T L I N G & D E M O L I S H I N G

1. The tenderer shall indicate the sale value of useful material taken from the canteen building adjusting the delmolishing cost. The net redit amount payable to the HasRaj College for the demolition of the building shall be calculated by deducting demolition cost from the salvages quoted. Note:- The contractor should visit the site before quoting this item. 2. The Job include following : a. Parapet walls b. Terracing c R.C.C. slab, Beams & Chajjas at Ground floor & First Floor. d. Bricks walls e. Wooden door & window frame & shutter. f. Aluminium doors & partition g. R.C.C.Working plateform, h. PVC water tank including all piping work i. Toilet fitting & fixture j. Wall tile work k.. Flooring l. Structrual steel work with Puff panel of cabin m. Electrical fitting & Fixture. n. MS & steel Railing of Staircase. o. window grills p. Removel Malba from College Campus. Note:- Coverd Area to be measured.

E A R T H W O R K

Excavation in all types of soil of all depth, including murrum, for foundations of wall, columns, plinth beams, basement, raft, ducts, trenches, underground sumps, septic tanks, soak well, manhole chambers, gully chambers, including shoring, strutting, bailing out water/pumping off water if required, re-filling the trenches, foundation pits, ramming, watering consolidating in 150mm to 200mm layers, removing and stacking simultaneously the excavated stuff any where within the site area and/or spreading soils in layers for site development filling in plinth in the same building or in college campus and consolidating etc. complete as directed.

All kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a College campus:

All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 600 mm dia.

Supplying and filling in plinth with Jamuna sand under floors including, watering, ramming consolidating and dressing complete .

Supplying chemical emulsion in sealed containers including delivery as specified.

Chloropyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) : Note:- With 5 year granttee of below mention works

Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:

With Chloropyriphos/ Lindane E.C. 20% with 1% concentration.

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.

With Chloropyriphos/ Lindane E.C. 20% with 1% concentration.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole :

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

C O N C R E T E W O R K

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - For all levels : Make :- Cement Ultratech, JK, Birla, ACC , Ambuja

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand including finishing the top smooth

R E I N F O R C E D C E M E N T C O N C R E T E

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement - All work up to plinth level : Make Cement:- Ultratech, JK, BIRLA, ACC , Ambuja

1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level excluding cost of centring, shuttering, finishing and reinforcement : Make :- Cement Ultratech, JK, BIRLA,ACC , Ambuja

1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size)

1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

DESIGN MIX CONCRETE

Providing and laying in position machine batched and machine design mixed M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge.(Note :- Cement content considered in this item is @ 330kg/cum."Excess/less cement used as per design mix is payable/recoverable separately) Make Cement :-- Ultratech, JK, BIRLA, ACC , Ambuja. Note:-The RMC plant got to be approved by Principal of college . Note:- Cube test report has to be submitted to Hans Raj College. - No extra payment will be made for cube test.

All works up to plinth level.

All works above plinth level up to floor V level.

Centring and shuttering including strutting, propping etc. and removal of form for All floor height up to 5.0m as per Drawing :

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Edges of slabs and breaks in floors and walls.

Under 20 cm wide

Small surfaces such as cantilever ends, brackets and ends of steps, caps and bases to pilasters and columns and the like.

Weather shade, Chajjas, corbels etc., including edges.

Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12mm thick.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. (Make: Tata, Sail, Jindal, Kamdhanu, Rathi)

Thermo-Mechanically Treated bars. -FE 500 D

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. (Make: Tata, Sail, Jindal, Kamdhanu, Rathi)

Thermo-Mechanically Treated bars. -FE 500 D

Brick Work

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Note:- Brick Quality test report for any type of brick work has to be submittted by vendor, No extra payment will be made for this.

Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry.

M A R B L E W O R K

Providing and fixing 18mm thick gang saw cut mirror polished premould and pre polished machine cut for kitchen platforms, vanity counters, window sills, facia ,Staircase tread, riser and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment complete at all levels. ( Basic cost of Rs. 2000/- sqm.)

Granite of any colour and shade

Area of slab up to 0.50 sqm

Area of slab over 0.50 sqm.

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width up to 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work.

Extra for providing opening of required size & shape for wash basins/ kitchen sink/ floor grating in kitchen platform, vanity counters and similar location in tiling / marble/ Granite/ stone work / flooring work including rubbing and polishing of cut edges etc. complete.

Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete.

25 mm long

32 mm long

40 mm long

50 mm long

Extra above basic item to give lapata finish on marble work / Granite work / stone work where ever required complete.

W O O D / COMPACT LAMINATE W O R K

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :

Second class teak wood

Note:- Wood quality test report for any type of work has to be submittted by vendor, No extra payment will be made for this.

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: Make :- Archid, Kitply, Century, GreenPlywood, Rainbow

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Extra for providing lipping with 2nd class teak wood battens 32 mm minimum depth on all edges of shutters (over all area of door shutter to be measured)

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality ( Make:- Greenlam, Merino)

1.0 mm thick.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1000 mm) with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

T-Line cubicle with SS grade 304 Size of cubicles:-1050(W) x 1550(D) x 1980(H) Thickness of Compact Laminate:- 12 mm, Door:- 610mm(W) x 1725 mm (H) Divider Height:- 1775mm Overall Height:- 1980mm (including bottom gap of 150mm) Make: Merino, Pefect, Stylam, Greenlam.

Urinal Modesty Panel Size:- 450mm x 900mm including all Accessories:- 1. SS Hinges with cover 2. SS Coat hook 3. SS Door Knob 4. SS Privacy Thumb turn c/w occupancy indicator 5. SS Adjustable Foot-316 grade 6. SS“U” Channel 7. SS”F” channel (Only corner unit) 8. SS Top Rail 9. Rubber Lining for groove 10. SS Screw 304 G & P PVC Wall plugs 11. SS Shoe box leg 12 mm Grade 316 Make: Merino, Pefect, Stylam, Greenlam.

S T E E L W O R K

Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying a priming coat of approved steel primer.

G.I. pipes

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) Make: Jindal, Ozone

F L O O R I N G

Marble stone flooring / skriting with 18mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with :

Raj Nagar Plain

Udaipur green marble

Kota stone slab flooring / stair (R & T) /skriting over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick.

Providing and fixing Ist quality ceramic glazed wall tiles size 600x300mm (conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (Make:- Somany, Asian, Kajaria)

Canteen Seating Hall (Basic Rate for Tiles:- Rs.45/-Sqft)

Canteen Kitchen & wash room (Basic Rate for Tiles:- Rs. 45/-Sqft)

Tile work in skirting, risers of steps and dado (up to 2 m height) over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.

Marble tiles (polished) Raj Nagar.

8 mm thick. Stair case (Basic Rate for Tiles:- Rs. 60/-Sqft)

Providing and laying Non-Skid Floor Tiles approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. (Basic Rate:- Rs. 700/- per Sqm) ( Make:- Somany, Asian, Kajaria, Orient)

Size of Tile 600x600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge.

Size of Tile 600x600 mm

Providing and laying Heavy Duty vitrified floor tiles (Stone Grade) Size of Tile 600x600 mm with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) complete. (Make -Somany/ Kajaria/ Asian/Orient)

Size of Tile 600x600 mm having thickness 16 mm with butt / flush joints including grouting the joints with white cement and matching pigments etc.

Supplying Heavy Duty vitrified floor tiles (Stone Grade) Size of Tile 600x600 mm with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades. (Make -Somany/ Pavit/ Kajaria/ Asian)

16mm thick

10mm thick

Supply Tactile Tile (Linear / Button) (for vision impaired persons as per standards) of size 300x300x15mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make inivory plus yellow shades in for / indoor outdoor floors such as footpath, court yard, multi modals location etc., in all shapes & patterns complete as per direction of Engineer-in-Charge.

R O O F I N G

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

F I N I S H I N G

12 mm cement plaster of mix :

1:4 (1 cement : 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement : 4 fine sand)

6 mm cement plaster of mix :

1:3 (1 cement: 3 fine sand)

6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams.

18 mm thick plain cement mortar band in cement mortar 1:4 (1 cement: 4 fine sand):

Raised Band

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand) :All height as per Direction Engineer & Incharge.

Flush / Ruled/ Struck or weathered pointing.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. Make : Asian, Berger, Nerolac

New work (two or more coats) over and including water thinnable priming coat with cement primer.

Applying one coat of cement primer of approved brand and manufacture on wall surface :

Cement primer.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm).

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Make : Asian, Berger, Nerolac

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

French spirit polishing :, Make : Asian, Berger, Nerolac

Two or more coats on new works including a coat of wood filler.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Make :- JK., Birla

S A N I T A R Y I N S T A L L A T I O N S

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : Basic Rate:- Rs. 3000/- per piece : Make:- Hindware, Cera, Jaguar, Somany, Equivalent.

White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : Make:- Hindware, Cera, Jaguar, Somany,Equivalent.

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required : (Rate:- Rs. 4500/- per Set) Make:- Hindware Italian collection, Cera, Jaguar, Somany.

Single half stall urinal with 5 litre P.V.C. automatic flushing cistern . Make:- Hindware, Cera, Jaguar, Somany, Equivalent.

Providing and fixing wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : Make:- Hindware, Cera, Jaguar, Somany, Equivalent.

White Vitreous China Flat back wash basin size 550x400 mm.

Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : Make:-Neelkanth, Nirali, Equivalent.

Kitchen sink without drain board - 610x460 mm bowl depth 200 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe - 40 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Make:- Saint Gobain, Modi, Equivalent.

Rectangular shape 453x357mm

Providing and fixing toilet paper holder :

C.P. brass

Providing & fixing Ringfit / Pasting Type uPVC (Type-B) conventional system for Soil, Waste & Rain Water pipe including testing of joints,coupler,bend, Tee,Y, Vent Cowl,End cap,Trap, Clamp and accessories complete as per direction of Engineer in Charge. note::- no payment will be paid for accessaries / joints. Make - Astral / Supreme / Prince / Prakash /Equivalent.

75 mm dia

110 mm dia

160 mm dia

Providing and fixing M.S. holder-bat clamps of approved design to PVC pipe and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. :

For 100 mm dia. Pipe

Providing and Fixing CP grating of approved quality and make - Rectangular type with openable circular lid 127 mm nominal size square 100 mm diameter of the inner round grating.

W A T E R S U P P L Y

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall Make : Supreme, Prakash, Polycab Astral, Equivalent.

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. - Make : Supreme, Prakash, Polycab Astral , Equivalent.

15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia .Pipes.

Making connection of CPVC / G. I. distribution branch with CPVC / G. I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : Make : Supreme, Prakash, Polycab, Astral , Equivalent.

20 to 40 mm nominal bore

50 to 80 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : Make : Astral , Ajay flow Gard Glynwed, Equivalent.

25 mm nominal bore

Horizontal

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank Make:- Sintex, Sheetal, Kamthanu, Equivalent.

Fixing C.P. brass fitting in toilet with extension pc., caps, CP pipe & nut - bolt, washer etc. complete as per following detail :- Approved Makes:- Kohlar / Jaquar / Hindware

Concealed stopcock with sliding cap

15 mm diameter small body bib cock

Basin inlet connection Long Threads

450 mm long copper pipe with 2 nuts & washers

Swan Neck Tap with spout

Bottle Trap

Extension Piece

Cutting holes up to 30x30 cm in walls including making good the same :

With common burnt clay F.P.S. (non modular) bricks.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.

D R A I N A G E

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Size 120x90 cm

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

W A T E R P R O O F I N G

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. Make: PIDLITE, SIKA, FOSROC, Dr. FIxid

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls up to 300mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry

With average thickness of 120mm and minimum thickness at khurra as 65 mm.

ALUMINIUM WORKS

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z / tee / angle sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Make:- HINDALCO, INDALCO, JINDAL, MAHAVIR, Equivalent.

For fixed portion

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Including :- Handle, Lock,Door stopper, window stay, Tower bolt, all Fittings).

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.50 mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg., for doors, including cost of cutting floors , embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness.

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

up to 5mm depth and 5 mm width

Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for separately).

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and fixing 12 mm thick frameless toughened glass of approved brand and manufacture, including providing and fixing top bottom & both side fixing arrangement and making necessary holes etc. all complete as per direction of Engineer-in-charge Make:- Modi, Saint Gobin, Equivalent.

E L E C T R I C A L W O R K S

Wiring for light point /fan point / exhaust fan point/call bell point with 1.5 Sq.mm FRLS PVC insultated copper conductor multistrand wire in surface/recessed PVC conduit, with modular switch, modular plate, suitable size GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor multistand copper wire etc. as required. Wire Make: Havells ,k k kable, Polycab, Finolex Conduit Make:- Supreme, Prakash, Satia, Switch Make:- Anchor Roma, North West, Legrand.

Loop Point Wiring for light point /fan point/exhaust fan point/call bell point with 1.5 Sq.mm FRLS PVC insultated copper conductor multistrand wire in surface/recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor multistand copper wire etc. as required. Wire Make: Havells ,k k kable, Polycab, Finolex Conduit Make:- Supreme, Prakash, Satia. Make:- Anchor Roma, North West, Legrand.

Wiring for 16 amps power outlet points with 4 sq.mm PVC insulated stranded copper conductor wires in concealed/recessed P.V.C. conduit as directed including providing 16 amps flush type switch and 6 pin socket with cover plate 5 sided G.I. outlet boxes for switches and socket and earthing the third pin with 2.5 sq mm PVC stranded copper wire complete as required (Only one outlet shall be connected on each circuit)Wire Make: Havells ,k k kable, Polycab, Finolex Conduit Make:- Supreme, Prakash, Satia. Make:- Anchor Roma, North West, Legrand.

Wiring for 16 amps power outlet points with 6 sq.mm PVC insulated stranded copper conductor wires for the first power outlet and 4 sq.mm PVC insulated stranded copper conductor wires for the second outlet, in concealed MS conduits in False Ceiling/ Walls/ Ceiling/ Floor ducts as directed including providing 16 amps flush type switch and 6 pin socket with cover plate, 5 sided G.I. outlet boxes for housing switches and socket, and earthing the third pin with 2.5 sq.mm PVC insulated copper conductor wires complete as required (Two power outlets shall be connected on each circuit) Make: Havells ,k k kable, Polycab, Finolex Conduit Make:- Supreme, Prakash, Satia. Make:- Anchor Roma, North West, Legrand.

Wiring for Metal clad Socket outlet points with 4.0 sq mm PVC insulated stranded copper conductor wires in P.V.C. conduit/ wall / floor ducts as directed including providing 25/32 A single phase Metal clad socket and plug top, 25/32 A SP MCB (motor duty), 2 mm thick M.S. box to house the above duly painted and earthing with 2.5 sq. mm PVC insulated stranded Copper Conductor wires complete as required. (for Split A/C Unit) Wire Make: Havellas Key Polycab

Wiring for 5 amps light plug outlets with 1.5 sq.mm PVC insulated stranded copper conductor wires in P.V.C. Conduits in ceiling/walls/floor as directed including providing 6 amps flush type 5 pin socket and 6 amps switch with cover plate, 5 sided G.I boxes for housing switches, sockets and earthing complete as required. (for general areas) Make: Havells ,k k kable, Polycab, Finolex Conduit Make:- Supreme, Prakash, Satia. Make:- Anchor Roma, North West, Legrand.

Providing and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. Conduit Make:- Supreme, Prakash, Satia,

Providing and fixing in position suitable 1.6 mm thick G.I. outlet box with 2 Nos RJ - 45 for Data/ voice outlet including crimpling with all fixing accessories as required.

Supply and Laying including numbering / ferruling of wire (8 digit) and the continuity test for each cable of Cat 6 - Telephone / Data cable in existing G. I. Channel / conduit.

Supply and fixing of 1.6 mm thick G.I Box along with RG 11 TV Co axial socket with Cover Plate for TV Outlets

Supply drawing connecting testing and commissioning of TV Coaxial cable RG 59 in existing conduit for CCTV System

Supply and fixing of 1.6 mm thick G.I Box with Hylum sheet over outlets as required.

Supplying, installation testing & commissioning of following Lighting fixtures complete. ( Make:- Philips, Siska, Wipro, Havells)

4' long LED surface tube Light as per approved material list

200mm dia Circular LED Light

Ceiling Fan (1400 mm ) dia 1400 RPM as per approved material list

Exhaust Fan (300 mm ) Heavy Duty with G.I. Louvers as per approved material list

Exhaust Fan (450 mm ) Heavy Duty with G.I. Louvers as per approved material list

Wall Fan (450 mm ) dia as per approved material list

SITC of Smart Black Board projector with celing mounting kit etc complete as per direction of Engineer-In-charge etc as required (Approved Make:- Vivitek / Panasonic / Dukane)

Providing and fixing in position the following copper strips and wires including providing all fixing accessories and effecting proper connections

Copper Flat 50 mm x 6 mm

GI Flat 50 mm x 6 mm

GI Flat 25mm x 6 mm

Copper Flat 25mm x 6 mm

GI Wire 8 SWG

Light & Power Distribution Board

Supply and installation of sheet metal enclosed double door 12 Way DB, each phase consisting of 12 Nos. 10/20 AMP SP MCB’s and controlled by one number 63 Amps DP MCB. Make:- Hager, Legrand,L& T, Equivalent.

Supplying and drawing of the following sizes of 1100 Volts grade PVC insulated copper conductor wires in Suitable Size of MS conduit including and termination for DB Sub mainMake: Havells ,k k kable, Polycab, Finolex .

4 x 10 + 2 x 6 sq. mm PVC insulated stranded copper conductor wires

4 x 16 mm + 2x 6 PVC insulated stranded copper conductor wires

4 x 25 + 2 x 6 sq. mm PVC insulated stranded copper conductor wires

Supplying, laying, effecting proper connections, testing & commissioning of the following sizes of 1.1 KV armoured/ unarmoured PVC insulated PVC sheathed aluminium /copper conductor cables conforming to IS : 1554 Part I - 1976 with latest amendments laid over MS supports in existing RCC ducts/ laid in ground /laid on Cable Trays including clamping the cables to supports in an approved manner as required complete with all accessories. Make:- Finolex ,Havells, Polcab, Equivalent.

3.5 c x 240 sq.mm AYFY Cable - AL conductor

3.5 c x 120 sq.mm AYFY Cable - AL conductor

3.5 c x 95 sq.mm AYFY Cable - AL conductor

4 c x 16 sq.mm YFY Cable - CO conductor

4 c x 10 sq.mm Armoured Cable - Copper

2cx1.5sq.smm

Supplying and making end terminal joints for the following size of 1.1 KV PVC insulated copper conductor armoured cables including providing heavy duty copper terminal crimping lugs, solder, insulation tape, approved sealing epoxy compound, Single compression brass cable glands, effecting gland connec­tions and effecting terminal connections to the equipment complete as required.

3.5 c x 240 sq.mm AYFY Cable

3.5 c x 120 sq.mm AYFY Cable

3.5 c x 95 sq.mm AYFY Cable

4 c x 16 sq.mm AYFY Cable

Design manufacture , supply and fixing in position the cable trays of the following sizes for supporting 1.1 KV grade armoured/unarmoured aluminium /copper conductor cables. Fabricate the cable trays from perforated 2mm thick M.S. CRCA sheet duly galvanised with expansion coupler plates duly galvanised, with bolts, washer and nuts. Knock out holes for cable connections as per approved design. The tray should comply with the specification of NEC (National Electric Codes) and NEMA (National Electric Manufacturers Association). The steel should be as per IS:226 and galvanising as per IS :2629/BS 729/ASTM 123. The rate shall also include for supporting steel , fish plates , fixing accessories , nuts bolts, supporting down rods, dash fastener, cutting the RCC etc. complete as required.

150 mm wide x 50 mm x 2.0 mm thick

300 mm wide x 50 mm x 2.0 mm thick

Sub Distribution Boards

Design, manufacture, supplying, assembling at site, insta­lling, testing and commissioning of the following cubical type, dead front, 2mm thick sheet steel enclosed, free standing indoor type extendible Sub-distribution Boards with vermin proof hinged lockable doors for each compartment provide bus bar interconnections for incoming and outgoing including feeders earthing and painting and as per specifications. Make:- Hanger, Legrand , L&T.

The Sub Distribution Board - 1 for Light & Power SDB-1 shall consists of : INCOMER Main Incomer 300 amps TPN MCCB (35 KA) terminals to receive 3.5 x 240 sq. mm AYFY cable connection on one side and Bus bar connection on the other side.Main Incomer 300 amps TPN MCCB (35 KA) terminals to receive 3.5 x 240 sq. mm AYFY cable connection on one side and Bus bar connection on the other side.

BUSBARS

400 amps 4 pole bus bar chamber of suitable length with Copper bus bars. All bus bars and interconnections shall be of suitable size copper strips current density of copper shall not be more than 1.6 Amps/ sq.mm provide 100% capacity for neutral bus bar.

INDICATING PANEL

3 nos. phase indicating lamps each backed up with MCB and switch shall be provided for incomer.

Provide Multi functional meter type Mach Smart 96 (96 mm x 96 mm) covering 25 electrical parameters for each incomer.

OUTGOINGS

2 No. 63 A TPN MCCB (35 kA) suitable to receive 4 x 16 sq mm AYFY Cable

16 Nos. 63 A TPN MCB (10 kA) suitable to receive 4 x 16 sq. mm YFY Cable

2 Nos. 20 A TPN MCB (10 kA) suitable to receive 4 x 4 sq. mm YFY Cable

3 Nos.32 A DP MCB (10 kA) suitable to receive 3x 4 sq. mm YFY Cable

The Sub Distribution Board -1 as described above and specifications complete.

Small Sub Distribution Boards

Design, manufacture, supplying, assembling at site, installing, testing and commissioning of the following cubical type, dead front, 2mm thick sheet steel enclosed, indoor type extendible Sub-distribution Boards with vermin proof hinged lockable doors for each compartment provide bus bar interconnections for incoming and outgoing including feeders earthing and painting and as per specifications. Make:- Hanger ,Legrand , L&T.

INCOMER

Main Incomer 100 amps TPN MCCB terminals to receive 3.5 x 95 sq. mm AYFY cable connection on one side and Bus bar connection on the other side.

BUSBARS

100 amps 4 pole bus bar chamber of suitable length with bus bars. All bus bars and interconnections shall be of suitable size.

INDICATING PANEL

3 nos. phase indicating lamps with fuses

OUTGOINGS

5 No. 63 A TPN MCB suitable to receive 4 x 10 sq mm & 4 x 6 sq mm wires

The Sub Distribution Board -1 as described above and specifications complete.

FIRE WORKS

Providing , fixing,jointing and testing of Heavy duty C-class M S . pipes conforming to IS with accessories like tees, elbows, flanged joints, rubber insertion, nuts, bolts or welded joints including fixing the pipe with suitable flat iron strip clamps/ brackets, structural members, dash fastener, cutting hole and chases in walls, floor, R.C.C. slab etc, and making good the same, incluiding painting pipes and fittings with one coat of primer and two coats of postal red enamel paint complete as reqd.

150 mm dia

80 mm dia

40 mm dia

25 mm dia

Supply, Installation, Testing and Commissioning External Yard Hydrant Stand Post ,Single Headed Yard Hydrant Valve with 80 mm dia flanged inlet intantannious gunmetal coupling of 63 mm dia with cast iron wheel ISI marked, conforming to IS: 5290(Type A), with ABS cap and chain etc. complete with all accessories as required.

Supplying and fixing First Aid Hose Reel, wall mounting swinging type completewith drum & bracket of MS construction, spray painted in Post office Red, confirming to IS : 884/1995 with upto date ammendments, complete with the following as required.

36 Meter long 20min dia water those Thermoplastic (Textile rienforced) Type- 2 as per IS: 12585

20 mm dia gun metal ball valve & nozzle

Drum and brackets for fixing the equipments on wall

Connection from riser with stop valve (gun metal) & M.S. Pipe

Providing and fixing C.I. sluice valves (With cap) of approved quality complete with bolts, nuts, rubber insertions etc. complete Make:Kirloskar

150 mm dia

Supply, installation, testing and commissioning of 100 mm dia bourden type, stainless steel dial type pressure gauge including brass isolation valve and siphon pipe having caliberation of 0-16 Kg/Sq. cm complete as reqd.

Supplying and fixing of Fire Man's axe with heavy insulated rubber as per standard conforming to IS: 926

Fabricating, Supplying, Installation, Testing and Commissioning Air Vessel of Continuous welded construction with flanged discharge header on the top of each riser fabricated out of 10 mm thick dished ends and 8mm thick MS sheet, Air Release Valve complete with suitable drain arrangement with 25 mm dia gun metal wheel valve complete with all accessories etc.as required of the following sizes

1.2 Metre high and 250 mm dia

Providing and fixing fire extinguisher of carbondioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve baring IS:3224/15683 mark internal discharge tybe, 1 metre long high pressure discharge hose, non conduction horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed

4.5kg capacity cylinder

Providing and fixing 9 liters capacity fire extinguisher water type gas pressure conforming to IS markingfixed to wall

Providing and fixing ABC type fire extinguishers complete in all respects.

Capacity 5.0 Kg

Providing and fixing ABC type automatic modular ceiling mounted type extinguisher with body poder coated10 lts. Capacity min.300 mm dia 68 degree centigrade but tempreature complete in all respectof approved make and model

Providing and fixing C.I. non-return valve complete with gunmetle seat, bolts nuts, washer & rubber insertions as reqired conforming to IS: 5312

150 mm dia.

80 mm dia

40 mm dia

Supply and erection of electric driven main terrace 'pump complete with

Supply, installation, connecting, testing and commissioning of photoelectric type smoke detector with mounting base blinming LED etc. complete as required. Make: Appolo/ System Sensor

Supply, installation, connecting, testing and commissioning of Response indicator. Make: Appolo/ System Sensor

Providing and fixing in position suitable 1.6 mm thick G.I. outlet box with 2 Nos RJ - 45 for Data/ voice outlet including crimpling with all fixing accessories as required.

Supply and Laying including numbering / ferruling of wire (8 digit) and the continuity test for each cable of Cat 6 - Telephone / Data cable in existing G. I. Channel / conduit.

Supply and fixing of 1.6 mm thick G.I Box along with RG 11 TV Co axial socket with Cover Plate for TV Outlets

Supply drawing connecting testing and commissioning of TV Coaxial cable RG 59 in existing conduit for CCTV System

Supply and fixing of 1.6 mm thick G.I Box with Hylum sheet over outlets as required.

S/D of Solid Copper conductor PVC Insulated two core Armoured cable of 1.5 sqmm size for working voltage upto and including 1100 V, in surface /recessed i/c saddling and with JB for connection of detector etc. as per site requirement. job complete in all respect.

Supply, installation, connecting, testing and commissioning of Rate of rise cum fixed temperature Heat detectors with mounting base blinking LED etc complete as required. Make: Appolo/ System Sensor

Supply, installation, testing and commissioning of Fire alarm panel 4 zone complete with visual indication of zone wise fire and fault indication, zone wise sounder signal complete with primary power supply at 230V with 24V sealed maintenance free (SMF) batteries with backup with 48 hours back-up with 300 minutes alarm with charger make as per approved material list) Make Agni/ ASE/ Safe Zone

Providing and fixing CPVC ball valve of approved quality, High or low pressure, with plastic floats complete : Make : Supreme, Prakash, Polycab Astral .

25 mm nominal bore

32 mm nominal bore.

Supply, installation, testing and commissioning of Fire alarm panel 12 zone complete with visual indication of zone wise fire and fault indication, zone wise sounder signal complete with primary power supply at 230V with 24V sealed maintenance free (SMF) batteries with backup with 48 hours back-up with 300 minutes alarm with charger make as per approved material list MakeAgni/ ASE/ Safe Zone

Supply, installation, connecting, testing and commissioning of Hooters cum strobe min. 80 db output. as per approved material list Make:- Agni/ ASE/ Safe Zone

Supply, installation, connecting, testing and commissioning of Manual Call Box in ABS plastic complete with cover switch and hammer as required complete. Make: Appolo/ System Sensor

Supplying, installation, testing & commissioning of BEAM DETECTOR with all labour and material as required to complete the job in all respects upto the entire satisfaction of engineer in charge Make: Appolo/ System Sensor

S & fixing of fluorescent exit sign board which can be hanged from the ceiling.

Supply and installation of fire extinguisher (4 kg) ABC / N2 with all necessary accessories complete as required. Make: SAFE GUARD/ NEWAGE/ OMEX/ LIFE GUARD

Providing and fixing 9 liters capacity fire extinguisher water type gas pressure conforming to IS markingfixed to wall Make: SAFE GUARD/ NEWAGE/ OMEX/ LIFE GUARD

Providing and fixing ABC type fire extinguishers complete in all respects. Make: SAFE GUARD/ NEWAGE/ OMEX/ LIFE GUARD

Capacity 5.0 Kg

VRV AC WORKS

VRV ODU (Suitable for Heating & Cooling )

VRV / VRF Equipment

Supply, Installation, Testing and Commissioning of Modular Type outdoor units having evaporative temperature control function equipped with Highly Efficient Scroll/Rotary Compressors all Inverter Compressor(s), special heat exchanger, Y- branch as required, outdoor unit support, auto check function for connection error, auto address setting, Refrigerant temperature control and capacity as mentioned below. All units are designed on VRT technology where Variable Refrigerant Temperature continuously adjusts both the inverter compressor speed and refrigerant temperature in cooling and heating, allowing our systems to meet the building load with the highest levels of seasonal efficiency at all times.

VRV/VRF System shall be suitable for working on 48 °C Ambient Temperature, with Refrigerant R-410A. Unit price shall be inclusive of full charge of Refrigerant Gas & Oil, Freight, Insurance as applicable In INR. The COP of systems mentioned below shall be 7.3 at 50% load, 35 °C DBT Ambient Temperature & at 27 °C DBT/ 19 °C WBT Inside Temperature.

20 HP( 10 HP x 2 Nos)

MAKE: DAIKIN / Mitsubishi/ Toshiba/O General

VRV INDOOR UNITS

SITC of VRV indoor units with evaporator coil,fan and fan motor drain pan,drain pump and corded Remote controller .The units shall be of following capacities :

Hi Wall Unit

MAKE: DAIKIN / Mitsubishi/ Toshiba/O General

SITC of Y Joint to connect idu & odu

Refrigerant Piping

Supply & Installation of interconnecting following sizes of one end expanded refrigerant copper pipe work of following outer diameter, insulated with 19/13 mm thick closed cell electrometric Nitrile rubber tubular insulation between each set of indoor & outdoor units with outer mechanical protection of alluminum cladding for all exposed pipes as per specification. The pipe dia upto 19mm shall be soft seamlessr & above 19mm dia shall be hard seamless . The thickness of the pipes shall be as per manufacturer standardAll piping inside the room shall be propelrly fixed/supported with suitable size of clamp/ M.S. hanger and all external piping shall run in M.S. painted cable tray (Price Extra) etc. as reqd.

MAKE: MAXFLOW / RAJCO / Mandev / Parasmani

28.6 mm O.D. Pipe Size with insulation of 19 mm thick

22.2 mm O.D. Pipe Size with insulation of 19 mm thick

19.2 mm O.D. Pipe Size with insulation of 13 mm thick

15.9 mm O.D. Pipe Size with insulation of 13 mm thick

12.7 mm O.D. Pipe Size with insulation of 13 mm thick

9.5 mm O.D. Pipe Size with insulation of 13 mm thick

6.4 mm O.D. Pipe Size with insulation of 13 mm thick

Supply & installation of electrical control cabling

Control / communication cabling for VRV Units (between ODU & IDU & for central controller unit), 2c x 1.5sqmm in pvc conduit as per specification

MAKE: POLYCAB / HAVELLS / KEI

Supply and fixing of perforated type GI cable tray of the following sizes as per specifications..

MAKE: SRG / ADITYA

300 mm x 50 x 1.6 mm thick with Cover for running copper pipe

Drain Piping

SITC of PVC piping complete with fittings, supports with 9mm thick insulation tube as per specifications.

25mm dia

MAKE: PRINCE / SUPREME / SETIA

Supply & Installation of copper armoured cabling(4c x 10sqmm) alongwith double earthing of suitable sizes in between the outdoor unit and Isolator

MAKE: POLYCAB / HAVELLS / KEI

Electrical panel and DBs

Supply & installation of Isolator switch of suitable size in weatherproof enclosure conforming to IP65 (to be located in the vicinity of outdoor unit).with following specs.

Incomer 100 amp MCCB

Busbar aluminium 150 amps

Outgoing 25 amps RCBO X 5 Nos.(with one spare)

MAKE: KEPL / Risha/ Advance

Supply Installation testing and comminssioning of Floor DB 36 way with 32 ampsDP incomer and 20 nos. 6 amps SP MCBs

Indo- Asian / Legrand / LT

Supply installation testing and commissioning of 3x2.5 sqmm flexible wirein PVC conduit of 20 mm medium density from DB to each indoor units

MAKE: POLYCAB / HAVELLS / KEI

CREATORS ENGINEERS & INTERIORS

SHILPI TECHNOCRATS LLP

ECO CONSTRUCTION

NEW BHARAT CONSTRUCTION COMPANY

NCI Global Infratech

SAS Buildtech