REPAIR/ REPLACEMENT OF EXISTING UNSERVICABLE UG CABLE,OH CONDUCTOR, LT PANELS AND OTHER CONNECTED WORKS AT MIL STN DHARAMSALA

Amount

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in any type of soil, complete all as specified and directed.

Returning filling in (soil) including spreading, levelling, watering and well ramming in layers n.exc 25cms thick in any type of soil complete all as specified and directed.

Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed.

PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

PCC 1:4:8 (nominal mix) type D-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

Plain cement concrete 1:2:4 ( nominal mix ) type B-1 (using 20 mm graded crushed stone aggregates) as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar ands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including necessary formwork where required complete all as specified and directed.

Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cms thick, complete all as specified and directed Note: Punned thickness shall be measured.

Sub class ‘B brick, old size, brick covering laid dry, flat, transversally along the length of cable on sand cushioning, with width equal to the length of the brick including taking out old bricks, complete all as specified and directed.

Mild steel galvanised iron tubing light grade for cable protection as in road crossing, along poles, walls, floors, drain of 80mm size fixed with MS clamps, nuts and bolts required complete all as specified and directed.

Mild steel galvanised iron tubing light grade for cable protection as in road crossing, along poles, walls, floors, drain of 50mm size fixed with MS clamps, nuts and bolts required complete all as specified and directed.

Mild steel galvanised iron tubing light grade for cable protection as in road crossing, along poles, walls, floors, drain of 40mm size fixed with MS clamps, nuts and bolts required complete all as specified and directed.

Dismantling poles/struts, any size and type including insulators and removing from site, complete all as specified.

Supply, jointing, fixing or passing through pipe , trenches or ducts, commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 400 sqmm 3.5 core for working voltage upto including 1100 volts conforming to IS-7098 (Part-I) 1988 including taking out existing unserviceable cable, complete all as specified and as directed.

Supply, jointing, fixing or passing through pipe , trenches or ducts, commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 240 sqmm 3.5 core for working voltage upto including 1100 volts conforming to IS-7098 (Part-I) 1988 including taking out existing unserviceable cable, complete all as specified and as directed.

Supply, jointing, fixing or passing through pipe , trenches or ducts, commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 95 sqmm 3.5 core for working voltage upto including 1100 volts conforming to IS-7098 (Part-I) 1988 including taking out existing unserviceable cable, complete all as specified and as directed.

Supply, jointing, fixing or passing through pipe , trenches or ducts, commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 70 sqmm 3.5 core for working voltage upto including 1100 volts conforming to IS-7098 (Part-I) 1988 including taking out existing unserviceable cable, complete all as specified and as directed.

Supply, jointing, fixing or passing through pipe , trenches or ducts, commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 50 sqmm 3.5 core for working voltage upto including 1100 volts conforming to IS-7098 (Part-I) 1988 including taking out existing unserviceable cable, complete all as specified and as directed.

Supply, jointing, fixing or passing through pipe , trenches or ducts, commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 25 sqmm 3.5 core for working voltage upto including 1100 volts conforming to IS-7098 (Part-I) 1988 including taking out existing unserviceable cable, complete all as specified and as directed.

Supply, jointing, fixing or passing through pipe , trenches or ducts, commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 16 sqmm 3 core for working voltage upto including 1100 volts conforming to IS-7098 (Part-I) 1988 including taking out existing unserviceable cable, complete all as specified and as directed.

Supply, jointing, fixing or passing through pipe , trenches or ducts, commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 10 sqmm 2 core for working voltage upto including 1100 volts conforming to IS-7098 (Part-I) 1988 including taking out existing unserviceable cable, complete all as specified and as directed.

Cable jointing kit for 1.1 KV grade cable for outdoor termination, heat shrink type joint complete with jointing material and accessories suitable for 4 core XLPE armoured aluminium conductor cable of size 70 to 120sqmm with suitable clamps made out of flat iron 50X6mm including nuts, bolts and washers, complete all as specified.

Cable jointing kit for 1.1 KV grade cable for outdoor termination, heat shrink type joint complete with jointing material and accessories suitable for 4 core XLPE armoured aluminium conductor cable of size 240sqmm with suitable clamps made out of flat iron 50X6mm including nuts, bolts and washers, complete all as specified.

Cable jointing kit for 1.1 KV grade cable for outdoor termination, heat shrink type joint complete with jointing material and accessories suitable for 4 core XLPE armoured aluminium conductor cable of size 400sqmm with suitable clamps made out of flat iron 50X6mm including nuts, bolts and washers, complete all as specified.

Supply and fix (in replacment) LT overhead lines on 9 meter steel poles with XLPE insulated ABC cable size 3-core X 50 sq mm + 1-core X 35 sq mm including hook, clamps nut bolts ets as per site requirement and as directed.

Cutting/ trimming of trees branches from LT/ HT lines upto 2 metre horizontal & 2 metre vertical distance from both sides of electric line including shifting of cut trees branches away from site complete all as directed. Note:- Distance between two adjacent poles irrespective of distance shall be considered as one span.

Steel tubular swaged poles complete with base plate 8mm thick welded with pole, finial taper plug, bolt, nut and screws as specified type 410 SP-31 (9m long) including one coat of red-oxide zinc chrome primer and two coats of aluminium paint on surfaces exposed to view and making 30cm wide strips (total 5 Nos) with yellow and black paint alternately on external surface above PCC benching including numbering with black paint and painting with bituminous paint internally complete and externally for portion embedded in PCC, complete all as specified and directed. Note:- Earth work & excavation and PCC shall be measured and paid under respective Items of BOQ.

Galvanized steel wire 4mm dia for earth wire/ guard wire onHT/ LT poles stretched without kinks, bend and binding with wire including fabrication of cradles hexagonal/ rectangular guards, spacers, road crossing etc., including taking down old wire of any type shape , size and removing from site, complete all as specified & directed .

Supply , fixing and straining of Aluminum conductor steel reinforced (ACSR) of any size on HT/LT over head line including necessary binding work, jumpering, maintaining proper sag as per IE rule including cutting of tree branches around the ACSR conductor within area of 5mtr complete all as specified & directed

Structural steel work as in cross arms, bracings, supports, clamp and back plate fabricated from steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed by Engineer-in-Charge and applying two coats of aluminium paint over one coat of red oxide zinc chrome primer including preparation of surfaces and dismantling old structural steel work in cross arms and stacking at site, complete all as specified & directed.

Painting of LT panel outdoor/indoor off sizes removing existing old paint with the help of sand/emery paper etc. Preparing surfaces externally including cleaning etc. Applying externally one coat synthetic enamel paint including cleaning and surface dressing upto 25cm depth around 1 mtr of the panels complete all as specified and directed by Engr-in-charge.

Re-stretching of ACSR conductor and earth wire of any size and type on HT poles including disconnecting and rewinding with insulators with suitable size of binding wire after restretching, connecting jumpers adjusting line dividers etc and cutting/trimming of tree branches upto 2 mtr clear distance from wire all as directed by Engr-in-Charge.

Supply and fix in replacement ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 125 Amps all as specified and as directed.

S&F in replacement of existing unserviceable MCCB any size/capacity with MCCB 4 pole 250 Amps 36 KA, MCCBs microprocessor release,overload adjustable = 0.4 to 1 x Inshort circuit adjustable 2.5 to 10 x Ir (250-400A) 2.5 to 8 x Ir (630A) time delay 0.1 - 0.2 sec. & suitable thimbles/extended terminal with nuts,bolts and washers etc including minor required additional/alternation for fixing and connecting up of MCCB all as directed by Engr-in-Charge. Note- Rate of extended terminal deemed to be included in this item.

S&F in replacement of existing unserviceable MCCB any size & capacity with MCCB 4 pole 200 Amps, Icu 36 KA MCCBs, adjustable thermal and magnetic release & suitable thimbles/extended terminal with nuts,bolts and washers etc including minor required additional/alternation for fixing and connecting up of MCCB all as directed by Engr-in-Charge. Note- Rate of extended terminal deemed to be included in this item.

S&F in replacement of existing unserviceable MCCB any size & capacity with MCCB 4 pole 160 Amps,Icu 25 KA MCCBs, adjustable thermal and magnetic release & suitable thimbles/extended terminal with nuts,bolts and washers etc including minor required additional/alternation for fixing and connecting up of MCCB all as directed by Engr-in-Charge. Note- Rate of extended terminal deemed to be included in this item

S&F in replacement of existing unserviceable MCCB any size & capacity with MCCB 4 pole 100 Amps,Icu 25 KA MCCBs, adjustable thermal and magnetic release & suitable thimbles/extended terminal with nuts,bolts and washers etc including minor required additional/alternation for fixing and connecting up of MCCB all as directed by Engr-in-Charge. Note- Rate of extended terminal deemed to be included in this item

Cutting of existing road/ floor/ plinth/drain for taking out/laying of UG cable through GI pipe including necessary earth work excavation and making good to match with existing surface complete all as specified with PCC 1:3:6 type C1 (using 20mm graded crushed stone aggregate) complete all as specified.

Repair of LT Panel such as door, hinge, front and rear side cover nut bolt, washer, locking arrangement etc and necessary items are required as site during repair of maintenance works and as directed.

Supply and fixing in replacement LTXL-Ultra heavy duty capacitor cylindrical type rating 10 KVAR 440 Volts with maximum ambient Temperature upto 70ºC including necessary material required at site for connection and as directed.

Supply and fixing in replacement LTXL-Ultra heavy duty capacitor cylindrical type rating 15 KVAR 440 Volts with maximum ambient Temperature upto 70ºC including necessary material required at site for connection and as directed.

Supply and fixing in replacement LTXL-Ultra heavy duty capacitor cylindrical type rating 20 KVAR 440 Volts with maximum ambient Temperature upto 70ºC including necessary material required at site for connection and as directed.

Renewal of lightning arresters (Set of three) expulsion type complete with all fittings, transmission class, discharge capacity 65 kilo amp for 11000 volts including taking out old unservicable arrester and removing from site complete all as specified and directed.

Replacement of Air termination single pointed aluminium rod 12mm dia and 300mm long complete all as specified.Note :- The rate is inclusive of supporting pipe 15mm bore and PCC required at site.

Supply and fixing in replacement Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. but 25x3mm aluminium strip all as specified and as directed.

Supply and fixing in replacement Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc.but 32x6mm galvanised iron strip all as specified and as directed.

Supply and fix in replacement of 40 watt New generation, IP 65 LED post-top family, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source including necessary electric connection along with 40mm dia GI pipe 2.5 mtr long complete all as specified and directed. Make: Havells cat part No. RUBYPT40WLED830PSYMTOPC or equivalent in Appx

Supply & replacement of existing unserviceable busbar box , installation, testing and commissioning of factory fabricated prewired bus bar, cubical type of appropriate size of 60cm x 45cm x 30 cm out door dust vermin proof, made out of 40x40x6mm angle iron frame/legs and 3.15 mm thick CRCA sheet with openable shutters on both sides (front & rear), powder coated externally and internally, having locking arrangement mounted on four legs 90cm high (30 cm below ground level and 60 cm above ground level),Panel embedded in PCC (1:2:4 ) type B2 of suitable size with clear working space all around the bus bar complete all as specified & directed by the Engr-in-Charge to accommodate the following accessories :- (a) MCCB 4 Pole 160 A 25KA - 1 No (Make:- Hager) Cat part No.HDA161Z with X160 frame MCCB fixed overload, fixed short circuitbreaking capacity (b) Aluminium bus bar 200 A for three phase and neutral duly insulated with sleeves of different colour RYB (Note : (i) Incoming and outgoing cable shall be fixed with appropriate size of copper thimble. (ii) Apron shall be provided at bottom for protection of cable to avoid entry of vermins, reptiles. (iii) Apron shall be provided at bottom for protection of cable to avoid entry of vermins, reptiles. (iv) Entries of all sizes of cables in panel should be done through adequate size of metallic cable glands.

Supply, install, testing & commissioning of CPRI approval LT panel board, outdoor type IP-54 protection as per IS-8623 , floor mounted, factory made suitable for 415 Volt, 3 Phase, 4 wire, 50 HZ, AC supply system having bus bar chamber made out of size 1.2m x 1.2m x 45cm with angle iron of size 40 x 40 x 6 mm , duly supported with mild steel angle iron on plain cement concrete foundation (As per manufacturers instuctions) having height 60cms from ground level & 30 cms below ground level, with aluminium bus bars duly insulated by insulation of RYB colour 630 Amps rating mounted on porcelain insulators. The panels shall be factory made , double door, made out of 3.15 mm thick MS sheet (CRCA) totally enclosed dust, vermin & rust proof front operated, front & rear opening with locking arrangement fixed with MS angle iron frame of size 40x40x6 mm and duly painted with two coats of synthetic enamel paint over a coat of red oxide primer with colour as directed including internal wiring with multi stranded copper conductor cable of suitable size incl lugs and cable gland to incoming and outgoing cable etc all as directed at site and comprising of the following:-

(a) MCCB 125 Amps, 4Pole, 415 Volts AC supply, Adjustable thermal and magnetic release type 25 KA-01 No. (Incoming) (b) MCCB 63 Amps, 4Pole, 415 Volts AC supply, Adjustable thermal and magnetic release type 25 KA-01 No. (outgoing) - 03 Nos (c) MCB TPN 32 Amp 415 V 50 Hz , 10 KA AC supply - 02 Nos (d) Aluminium bus bar 200 A for three phase and neutral duly insulated with sleeves of different colour RYB Note:- (i) Incoming and outgoing cable shall be fixed with appropriate size of copper thimble. (ii) Apron shall be provided at bottom for protection of cable to avoid entry of vermins, reptiles. (iii) Entries of all sizes of cables in panel should be done through adequate size of metallic cable glands.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15 mm bore including provn of concrete pit in plain cement concrete M-15 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-15 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron strip 32X6 mm size (as earth lead strip), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 40 mm bore including provn of concrete pit in plain cement concrete M-15 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-15 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 25 of tender doucments.

M/S MALHI CONSTRUCTIONS

Mahashakti Enterprises