SPECIAL REPAIR TO BLDG NO. BK-8/15 AND BK-8/17 UNDER GE CLEMENT TOWN, DEHRADUN

Amount

Dismantling of Asbestoes cement (corrugated, semicorrugated, etc) sheets any gauge, thickness in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coated GI based plain steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge etc fixed with self tapping screws complete all as specified and directed.

Demolition of brick work or stone masonry/stone slabs built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed.

M&L Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified and directed.

Taking down cement plaster, in any thickness from brick or stone walls,/facia of roof Chajjas,roof projection,ceiling etc including raking out joints, hacking for key, scrubbing down with water etc and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

M&L Rendering 15 mm thick on fair faces of brick work or concrete walls internal surfaces in CM 1:6 finished to even & fair without using extra cement complete all as specified and directed.

M&L 15mm thick rendering cement mortar (1:4) on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surface of internal wall to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of oil bound distemper over a coat of 1mm thick wall putty on plastered surface using roller all as specified and prescribed by manufacture of paint complete all as specified and directed.

M&L for two coats of cement based paint over a coat of cement wash to newly plastered surfaces including preparation of surfaces complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) and including removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

M&L 25mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in sub bases of floor complete all as specified and directed.

M&L cement concrete 1:3:6 type C-2 (using 40mm graded aggregate) 75 mm thick as in plinth protection/hard standing surface finished even and smooth without using extra cement complete all as specified and directed.

M & L Cement concrete, (1:3:6) type C2 (using 40mm graded crushed stone aggregate for surface channels and drains complete all as specified and as directed.

M&L extra for forming fair finished drain or channel any inner girth in cement concrete, using extra cement, including forms, mould, mitred/stopped ends etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for coloured vitrified Ceramic tiles of any design and pattern, 600x600x9 to10 mm thick, as in floor etc incl 15 mm thick screed bed in CM 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles complete all as specified and directed.

Ditto as item No 17 above but as in skirting/dado over 10mm thick cement plaster in CM 1:4 complete all as specified and directed.

M&L for Non- skid coloured ceramic tiles of any design and pattern, 7 to 8 mm thick (square/rectangular) area of each tile exe 0.11 sqm but not exe 0.18, in floor etc incl 15mm thick screed bed in CM 1:6 , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles complete all as specified and directed.

All as per item No 19 above but as in skirting/dado over 10mm thick cement plaster in CM 1:4 complete all as specified and directed.

Dismantling wall and ceiling boards including cover fillets of any descrition complete all as specified and directed.

M&L for false ceiling with semi perforated 12mm thick micro triangular edged at all heights with GRG (glass fiber reinforced gypsum) false ceiling tiles of size 595x595 of approved texture design and pattern having moisture content less than 2%, humidity resistance of 99%, NCR 0.50 to 0.75 as per IS 8225, 1987, non combustible as per BS 475 (Part-IV 1970 and light code description unit rate No 429 sub head 26.0 new technologies and material) reflectance of 85% minimum to laid in true horizontal level suspended on interlocking metal 'T' grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @ 120gms per Sqm) including both side comprising of main 'T' runner of size 15x32mm of length of 3000 mm, cross 'T' of size 15x32mm of length 1200mm and secondary intermediate cross 'T' of size 15x32mm of length of 600mm to form grid module of size 600x600mm suspended from ceiling using galvanised metal sheet item (galvanised @ 80gms per Sqm) i.e. 50mm long 8mm outer diameter M-6, fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjusters of size 85x25mm galvanised iron perimeter wall angle of size 24x24x0.4mm of length 3000mm to be fixed on perimeter of wall/partition with the help of plastic rawal plugs at 450mm center to center and 40mm long dry wall screw. The work shall be carried out as per specification complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size n.exc 1.50 Sqm and removing from site complete all as specified and directed.

All as per item No.23 above but exc 1.50 Sqm and n.exc 4.00 Sqm each complete all as specified and directed.

M&L Solid (125mm x63 mm Double Rebate) factory made 100% solid WPC brown door frame made from 100% LEAD FREE (Single extruded process) material with density 780 kg/ Cum & manufactured by an ISO: 9001-2015 certified company, all as per specification drawings as directed by Engg-in-Charge. The door frame should be Water Proof, termite proof, fire retardant and having excellent screw holding capacity and shall be fixed with 6 Nos 150mm long hole fasterners complete all as specified and directed.

M&L Solid (100mm x63 mm single rebate) factory made 100% solid WPC brown door frame made from 100% LEAD FREE (Single extruded process) material with density 780 kg/ Cum & manufactured by an ISO: 9001-2015 certified company, all as per specification drawings as directed by Engg-in-Charge. The door frame should be Water Proof, termite proof, fire retardant and having excellent screw holding capacity nd shall be fixed with 6 Nos 150mm long hole fasterners complete all as specified and directed.

M&L 30mm thick moulded plain WPC solid door shutter: providing (30mm thick) MOLDED WPC Brown Factory made 100% solid door (Conforming As per IS: 4020) made from 100% LEAD FREE single extruded with 2,4 or 6 raised panel design on the front side with 10mm deep mould on single side with wood grain texture and back side plain with density not less than 600kg/Cum. Manufactured by an ISO: 9001-2015 certified company. The door should be water Water Proof, termite proof, fire retardant and having excellent screw holding capacity complete all as specified and directed.

S&F windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including of all taxes complete all as specified and directed. (Make :- Tata Pravesh/ NCL Buildtek Ltd/ Elixir Met Form Pvt Ltd.)

S&F framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; framed angle for chain link fixing, barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

S&F 1.00mm Plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) comoplete all as specified and directed.

S&F 100 mm long mild steel butt hinges medium weight complete all as specified and directed.

S&F aluminum anodized barrel tower bolt 200mm long of extruded section complete all as specified and directed.

S&F aluminum anodized sliding door bolt 300mm long with hasp and staples (bolt type) and fixing clips of sheet cast of extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

S&F aluminum bow handle "D" type anodized 150mm long complete all as specified and directed.

S&F for Stainless steel curtain rod, 25mm dia with fixing brackets and decorative type knobs both side of each rod including taking down old curtain rod or pelmet boxes complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position as in framed work complete all as specified and directed.

S & F Rolled Mild Steel ( confirming to Fe 410 - W Gde-E-250 Quality-A) as in roof trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee,angle, channel or flat sections) including distance peices cleats etc complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm width & girth not otherwise described and applying two coat of synthetic enamel paint (Ist quality)over a coat of red oxid primer complete all as specified and directed.

M & L for providing reinforced cement concrete (nominal mix) type B1 1:2:4 using 20 mm graded stone aggregate as in Beam,cantilevers,lintels etc including demolition of RCC all as specified and directed.

S & F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per item No. 41 above but 6-8mm bars in stirrups complete all as specified and directed.

M & L for use and waste of formwork to sides and soffits of floor, lintels band & beams etc. with rough finished of concrete all as specified and directed.

Dismantling and taking down U/S copper / aluminium point wiring (light, fan, socket, power) complete with fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified and directed.

Taking down carefull serviceable ceiling fan from existing position of any height and refixing the same ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Dismantling and taking down u/s sub-main wiring/service wire of any size including wooden batten / PVC Conduit etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified & as directed.

Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit MMS ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates.

All as per item No-47 but One 3pin/5pin 5/6 Amps socket out let on same board with other switches , with cables 1.5 sq mm size , complete all as specified and directed.

All as per item No-47 but One 3pin/5pin 5/6 Amps socket out let on independent board with other switches, with cables 1.5 sq mm size, complete all as specified and directed .

All as per item No-47 above but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point complete all as specified and directed.

Supply and fixing switch modular single pole,, one-way 6Amps, 1 module 240 Volts AC complete all as specified and directed.

Supply and fixing switch modular single pole,, one-way 16 Amps, 1 module 240 Volts AC complete all as specified and directed.

Supply and fixing modular socket, 6A -2/3/5 pin combined 2 module ISI marked 230 volts, 50Hs complete all as specified and directed.

Supply and fixing modular socket, 6A/16A-5/6 pin combined 2 module ISI marked 230 volts, 50Hs complete all as specified and directed.

Supply and fixing step socket type modular fan regulator 240 V , 100 Watt 2 module complete all as specified and directed.

Supply and fixing batton/angle holder insulated body with back plate, suitable for batten fittings complete all as specified and directed.

Supply and fixing ceiling rose surface bakelite 65x25mm dia having three terminals complete all as specified and as directed.

S&F of decorative box type 20 -22watt LED fittings with and including LED T-8 tube light 20 watt of fire retardant engineering grade complete with all accessories internally pre-wired, connecting up with and including three core sheathed flexible copper conductor cable of required size and including mounted on PVC/Wooden round/square blocks-02 Nos complete all as specified and directed.

S&F of 10 watt LED light fitting mirror type with high out put diffuser 2 feet, 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size other fixing accessories complete all as specified and directed.

S& F in repair oval shape Bulk head Edge-lit LED fitting comprising with high brightness LED 10 watt, IP-67 protection all as per cat part No- LBHP-10-CDL of make Crompton / or equivalent make in philips / Havells / C&S.

S & F in repair LED building security light 45 watts with inbuilt daylight sensor which swiches ON/OFF automaically in the absence/presence of sunlight. IP-66, IK08 pressure die cast fabricated aluminium housing with epoxy powder coated finish complete with suitable size bracket complete all as specified and directed.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated bus bar complete all as specified and directed.

S & F vertical load line in sheet metal enclosures MCCB TPN DB's with double door for incorporating MCCB as incomer and MCBs SP/SPN as outgooing , IP-43 , TPN 4 way with 200 amps rated busbar, 440 volts, as per IS-8623 including taking out old UNSV DB and making good the disturbed surface of wall and match with the existing surface compelte all as specified and as directed. (Note- MCCB 100 Amps, 3 Pole, 16 KA is deemed to be included in quoted rate)

Supply and fixing MCB SPN 40 Amp 240 V AC 10 KA repturing capacity complete all as specified and directed.

Supply and fixing MCB 5 to 30 Amp 'B' series 10 KA repturing capacity complete all as specified and directed.

Supply and fixing single pole and neutral enclosure with a two pole and earth plug socket complete with one, single pole MCB 20 Amps 10 KA repturing capacity 240 Volts AC complete all as specified and directed.

Taking down old u/s cable & Supply and laying or fixing or passing through pipe, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade , cross - sectional area of 25 sqmm 4 core complete all as specified & as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for taking out cables, pipe line etc for repairs / laying cables etc and getting out in soft / loose soil complete all as specified and directed.

M & L for fine dry sand cushioning for underground cable by providing layers of sand 8 cm before laying and 15 cm deep after laying the cable including streching the cable ( measurement to be taken after punning down consolidated thick ness ) complete all as specified and directed.

Supply and laying , un-reinforced precast concrete cable cover, class LV, Type 1, flat, size 250mmX 150mmX40mm with breaking load capacity 200 KG complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removal of excavated material [soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply and fixing sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLSH) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium gradeconcealed in wall as per existing along with 6.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion complete all as specified and directed.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed.

SAVV BUILDERS

High Tech Metal India

sidh builders

SWASTIKA BUILDERS

M/S GOPAL JEE SINGH

V R Associates

M/S VIJAY TRADERS

M/s RK ENTERPRISES

ANEJA AND COMPANY

RADHA ENTERPRISES

YP INFRA