Spl repairs to building No WL-10/4 10/9 and WL-31/8 (OR md accn) of DSC Centre under AGE (I) Cannanore.

Amount

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for laterite stone masonry, regular coursed, well bonded and solidly hearted , built in CM (1:6) all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L 25mm thick PCC 1:2:4, Type B0 (using 12.5mm graded stone aggregate) as in flooring and finished even and fair all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding(but not backing),removing serviceable tiles and rubbish off the premises all as directed.

M&L for coloured non-skid ceramic tiles, 7 to 8mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for coloured glazed ceramic tiles, 7mm to 8mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

S&F Stainless steel sinks 1mm thick with plugs, washers and waste; including bedding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe, overall size 495mm x 420mm, bowl size 410 x 330 x 160mm etc complete all as specified and directed.

Taking down chowkats with shutters any description n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters any description exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

Taking down wooden door shutters of any description n exc 1 Sqm each all as directed.

Taking down wooden door shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each all as directed.

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast including necessary form works all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

S&F 35mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc; (with out sash bars), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

M&L for second class hardwood, panelled shutter 35mm thick (any number of panel) with lock rail and panel of 9mm BWP, 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

Material & Labour for 2nd class hardwood glazed and skeleton shutters, 30 mm thick open rebated and prepared to receive glass, gauze, etc., but divided into squares, with plain, chamfered or rounded,mitred and rebated sash bars,any numbers fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); and fitted to chowkats complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc, with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

S&F 3mm thick plane sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane with putty or fixed with beads all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

S&F 150mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F 200mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

S&F stainless steel butt hinges medium weight; 100mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F stainless steel butt hinges medium weight; 75mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 100mm size fixed with stainless steel screws all as specified.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L for preparation of new untreated steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

M & L for 75 mm thick plain cement concrete 1:3:6, type C2 using 40mm graded aggregate as in plinth protection etc including necessary form work complete all as specified and directed

M&L for complete removal of existing treatment on surfaces of wall by scrapping down and applying 1mm thick acrylic wall care putty and making the surface smooth and even and applying two coats of oil emulsion distemper over a coat of wall primer (water or solvent thinnable) and all as specified and as directed.

M&L for preparation of new plastered wall surfaces and applying 1mm thick acrylic wall putty for making the surface smooth and even and applying one coat of wall primer(water thinnable/solvent thinnable), applying two coats of oil emulsion distemper by approved applicator of the manufacturer of the paint and all as specified and as approved all as specified and directed.

M&L for preparation of old treated wall surfaces and applying two coats of cement base paint all as specified and directed.

M&L for preparation of new plastered wall surfaces and applying two coats of cement base paint over a coat of primer all as specified and directed.

M&L for preparation of old plastered surfaces and applying two coats of white wash on wall surfaces all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling surfaces all as specified and directed.

M&L for GI 600 x 600 mm snap grid frame, powder coated sections comprising of undermentioned sections etc for grid frame including 4 mm thick non asbestos plain ceiling board of M/s Everest or equivalent ceiling grid system as per regular T-2430 or equivalant in Ramco/Charminar/Amstrong placed on GI grid including applying two coats oil bound distemper over a coat of primer all as specified and directed :- (a) Suspended GI main runner 38 x 24 mm bulb Tee sections fixed with 4 mm dia GI bar @ 1200 mm c/c, level shall be adjusted with fly/bionet screws. (b) Placed in position cross Tee 1200 mm long and 28.8 x 24 mm bulb Tee section @ 605 mm c/c using snap grid and bionet fixing arrangement to secure main runners. (c) Ceiling GI 28.8 x 24 mm fixed with PVC Rawl plugs and GI screws tie secure with walls and all as per manufacturers instructions complete all as specified and directed.

Dismantling wall and ceiling boards or insulation boards/slabs/blankets any thickness, including cover fillets all as specified and directed.

Supply and fix mild steel chromium plated curtain rod 20mm dia fixed to wall including suitable bracket complete all as specified and directed.

Taking up or down steel tubing and connecting including cleaning for removing to store of sizes upto 25mm bore all as directed.

S&F for 15mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings or in floors etc. all as specified and directed.

S&F for 20mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed to wall/ceiling or on floor all as specified and directed.

S&F stop valve 20mm bore cast copper alloy, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

S&F Vitreous China squatting pan “Orissa” pattern, of size 580 x 440 mm white, with integral foot rests, (excluding flushing cistern and flush pipe), including provision of lime concrete bedding, connection to trap and to flushing pipe, anti-syphonage pipe, etc and joint between flushing pipe and socket of WC pan, complete and making good to the floor and fixed in repairs all as specified and directed.

S&F in repairs PVC valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including low or high density PVC flush pipe all as specified and directed.

Dismantling and breaking up drain pipes 75/100mm bore (cast iron) set in cement mortar any dia of pipes and removing debris outside MD land

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with rubber ring joints laid in trenches or in floors all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with rubber ring joints fixed to wall all as specified and directed.

M&L PVC (SWR) pipe type 'B' 110mm bore single socketed with rubber ring joints laid in trenches or in floors all as specified and directed.

M&L PVC (SWR) vent cowl 75mm dia with solvent cement joints all as specified and directed.

S&F 75 mm bore, PVC (SWR) bends with access door all as specified and directed

S&F 110 mm bore, PVC (SWR) bends with access door all as specified and directed

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

M&L for 75mm diameter PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

S&F grating square 150mm size of PTMT complete all as specified and as directed.

Cutting chases for concealing water tubing and making good, in stone or concrete block or slab or walls, cutting not exc 10cm girth complete all as specified and as directed.

S&F in repairs Vitreous China Wash basin, white, flat back, size 630 x 450 mm, including CI brackets, (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F 15mm pillar taps, cast copper alloy with capstan heads, chromium plated , screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

Supply and fix PVC connecton 45cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

S&F in repairs bib tap 15mm dia, chromium plated, fancy type, cast copper alloy, screwed down, screwed for iron pipe or ferrule and complete all as directed.

S&F in repairs stop cock 15mm bore cast copper alloy, chromium plated, fancy type, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup complete all as specified and directed

Taking down carefully copper/aluminium point wiring of light, fan, socket or power complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floor ceiling etc. all as directed

M&L Point wiring complete with 1.5 Sq mm single core PVC insulated unsheathed copper conductor FRLS cable multi stranded 1100 Volt grade drawn through and including non metallic rigid PVC conduit concealed to wall and fixed to ceiling/roof etc with necessary fixing accessories such as bend elbow socket etc with fixing material including terminal box made out of 1.22mm thick MS sheet concealed in wall covered with laminated sheet top cover of 3mm thick cadmium plated screws with cup washer including 1.5Sqmm single core PVC insulated un sheathed copper conductor FRLS cable multi stranded 1100Volt grade as earth continuity conductor green in colour connected to common earth dolly complete all as specified and as directed for One light/fan/bell point controlled by one switch.

All as per item No 68 here in before but for One 3 Pin, 5 Amps switch socket combination on independent board all as specified and directed.

All as per item No 68 here in before but for One 3 Pin, 5 Amps socket on same board with other switches all as specified and directed.

All as per item No. 68 on here in before but for one 3 pin 15 amp switch socket combination on independent board with 2.5Sqmm unsheathed PVC insulated copper conductor FRLS cable including 2.5 Sqmm PVC insulated copper cable for earth continuity conductor complete all as specified.

S & F switch piano flush type, single pole, one way, 5 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F PVC ceiling rose round shape, three terminals, polycarbonate, isolated body including connecting up electrically all as specified and as directed.

S & F socket 5pin 5/6 Amps, multipurpose, flush type, non-interlocking type, including connecting up electrically complete all as specified and directed.

S & F socket 3pin 5/15 Amps, multipurpose, flush type, non-interlocking type, including connecting up electrically complete all as specified and directed.

S & F switch bell push, flush type, 240 Volts, single pole, 5 Amps including connecting up electrically all as specified and directed.

S & F switch piano flush type, single pole, one way, 15 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S& F calling bell electric AC 240V, single pole, ding dong type and connecting up electrically all as specified and directed.

S&F in repalacement lamp holder, PVC/poly carbonate type with back plate suitable for batten fitting all as directed.

S&F stepped type electronic fan regulator, full rotation,200W, SP, 230V onnecting up electricallyall as specified and directed.

Taking down unserviceable fluorescent tube light fittings, S & F Decorative ultra slim square profile linear LED light fittings with extruded polycarbonate, heat sink, environmental friendly, energy efficient, decorative end cap ready to use pack of 20 W LED 6000K, model of Havells LUMILINEEBS9WLED830SPCWH (HSN Code 9405) or equivalent in Syska or Crompton Greaves with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

Taking down unserviceable fluorescent tube light fittings, S & F Decorative ultra slim linear LED light fittings with extruded AI, heat sink, environmental friendly, energy efficient ready to use pack of 10 W LED 6500K, model of SSK-T-5, 12W of Syska or or LHEXBTP7IN1W009 of Havells or equivalent of Crompton Greaves or in Philips, with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

Supply and fixing LED bulk head luminaries of 10 watts withABS body and polycarbonate diffuser CCT 6000K IP 54 on wall of energy saving and environmental friendly long life with driver of HAVELLS or equivalant of CG or Philips and electrically connecting up all as directed.

M&L in replacement for sub main wiring with two runs of single core 6 Sq mm copper conductor FRLS cable, PVC insulated, unsheathed multistanded, 1100 V grade drawn through and including non metallic rigid PVC all accessories such as bend,elbow,socket,tee saddles etc fixed concealed to wall / fixed to ceiling etc including 6 Sq mm single core copper conductor FRLS cable PVC insulated, unsheathed multistranded 1100 V grade as earth continuity conductor connected to common earth dolly complete all as specified and directed. Note :- 3 runs of 6 Sq mm copper cable and one run of PVC conduit will be measured as one length.

S & F MCB SP, 240 Volt, 6 to 32Amps including electrically connecting up using wiring lugs all as specified and directed.

S&F for RCBO capacity 40 amp, 30mA, 2 module, 240V, short circuit breaking capacity 10kA of L&T cat No AUF3C204003 conf to TEC 61009-1, IS 12640-2, EN 61009-1 or equivalent in Indo Asian or Havells including electrically connecting up using wiring lugs all as specified and directed.

S & F sheet metal powder coated enclosure factory made for MCB DB, SPN 8 way with 200 Amps bus bar, 240 Volt, double door type, fixed/flushed on wall including electrically connecting up and taking down old unserviceable DB complete all as specified and directed.

S&F in repalacement LED ball type lamp 15watt all as directed.

M&L for Earthing complete with using GI earth plate electrode 600x600x6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 mtr below normal ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness off 15 cm all around the plate with using 4 mm dia GI Wire as earth lead moulded and retreived to earth plate at one end and connected to main switch / control board at another end with and including 15 mm dia GI light grade from upper end of earth plate upto external face of the wall of the building including 20 mm dia bore GI pipe light grade as water pipe from chamber to upper edge of the plate GI funnel with wire mess fixed on water pipe and provison of PCC 1:2:4 type B-1 (Using 20 mm Dia graded stone aggregate) duly reinforced with mild steel round bar 6 mm dia @ 150 mm c/c both ways with 10 mm dia mild steel bars as in lifting handle with and including necessarry excavation and earth work including laying the pipe concealed in floor / wall allas per plate NO-3 of SSR Part-I complete all as specified and directed and testing on completiopn (Note:- If the desired resistance is not found earthing shall be redone by the contractor at no extra cost to Govt).

M&L for taking out old unserviceable ceiling fans from site and removal of burnt winding wire by cutting, clening slots and re-Winding of AC ceiling fan motor 1200/1400 mm of any make with super enameled copper winding wire of existing gauge varnishing with E class insulation varnish, threading, including neceassry laith work and refixing in same location, connnecting up electrically with appropriate size copper conductor cable upto connector block Complete all as specified and directed by Engineer-In-Charge . Notes:- (i) Doctor brand or equivalents ISI brand varnish shall be used. (ii) Motor winding shall be wound with machine only. (iii) BIC/HTP or DEVIDYAL. make super enameled copper winding wire shall only be used. (iv) Weight of copper winding wire per fan shall be min 350 gm.

S&F in replacement of old unserviceable gun metal bush of ceiling fan including neceassry laith, Grinding and welding work Complete all as specified and directed by Engineer-In-Charge .

S&F replacement of old unserviceable capacitor AC 230 volts 2.5 mfd (ISI marked) Complete all as specified and directed by Engineer-In-Charge .

S&F in replacement of old unserviceable ball bearing of size 6200 to 6204 including neceassry laith , Grinding and welding work Complete all as specified and directed by Engineer-In-Charge . Make NBC/SKF

S&F in replacement of old unserviceable shackle assembly kit (Rubber real -01, MS split clamp two Nos, nuts and bolts washers- 2 Nos & split pin -02 Nos) suitable for ceiling fan of 1200/1400mm sweep Complete all as specified and directed by Engineer-In-Charge

S&F in repalcement of old unserviceable down rod of ceiling fan of 20 mm bore "medium grade" with split pin, hanging clamp and rubber real (length of rod not less than 45cm and not more than 60cm) in white/brown colour (fully furnished) Complete all as specified and directed by Engineer-In-Charge.

Material and Labour for removing old paint by scraping down with sand paper including washing and filling cavaties with filler and applying two coats of painting with synthetic enamel paint over a coat of red oxide primer by spray gun using spray gun method painting to ceiling fan of 1200mm sweep at site including 03 Nos blades, motor (both sides) down rod, writing MES No/ Srl No on the ceiling fans Complete all as specified and directed by Engineer-In-Charge.

JEETH CONSTRUCTION