REPAIRS/MAINT OF VARIOUS TYPES OF PUMP SETS WITH ALLIED WORKS AT AF STN SIRSA

Amount

Dismantling and removing the Electric motor 1HP/1.5HP 3 Phase, AC,415V of the any Make/Model from existing position, Shifting to workshop for the repair work, removing the burnt winding, cleaning rotor, stator, re-winding the motor with super enameled copper wire of size equivalent to the original winding including insulated packing materials, Varnishing, Drying etc and installing back to the original position, testing and commissioning on full load for 8 hrs continuous running for the following capacities of motor all as specified & directed by Engr-in-Charge. NOTE : Bearing & Bush will be measured and paid separately under relevant items. (Labour Elements already included in this job)

All as per item No. 1 but for 2/3 HP, 3 phase, AC, 415V

All as per item No. 1 but for 7.5 HP, 3 phase, AC, 415V

All as per item No. 1 but for 10 HP, 3 phase, AC, 415V

All as per item No. 1 but for 20 HP, 3 phase, AC, 415V

All as per item No. 1 but for 40 HP, 3 phase, AC, 415V

S&F in repairs Rotor (Impeller) as per existing of Cap, 1/2 HP, complete all as specified and as directed.

S&F in repairs Shaft including Mechanical Work for fixing Impeller /Sleeve/ Ball Bearing, of Pump 1/2 HP, complete all as specified and as directed.

S&F in repairs Low Joy Coupling including Rubber Star Packing and necessary Key for fixing on Shafts, complete all as specified and as directed..

Material & Labour for Rewinding Submersible Motor 3 HP, 3 phase, AC, 415V with PVC insulated Copper wire of same Gauge High Class Insulating Materials of the existing Size, Varnishing, Heating, etc., for the following capcities of Motor all as specified & directed. NOTE : Bearing & Bush will be measured and paid separately under relevant items. (Labour Elements is already included in this job)

All as per item No. 10 but for 15 HP, 3 phase, AC, 415V

All as per item No. 10 but for 20 HP, 3 phase, AC, 415V

All as per item No. 10 but for 25 HP, 3 phase, AC, 415V

Disconnecting & Dismantling Unserviceable Centrifugal/ Mono Block/ Vertical High pressure Pump Set any type & any Model 7.5/10 HP by disconnecting from Motor, Suction and Delivery Line for carrying out repairs at Workshop by replacing Defective/ unserviceable Parts including Greasing replacement of Packing Sheet, Gland, Stud, Bearing, Cover Sheet & Lath Work of Impeller Shaft, etc. and Testing & Commissioning after repairs for improved performance including Transportion, complete all as specified and as directed. NOTE : Bearing & Bush will be measured and paid separately under relevant items. (Labour Elements already included in this job)

Supply only Ball Bearing (as approved) suitable for Pump Set 7.5/10 HP, complete all as specified and as directed. Make - NBC/SKF/ARB

Supply & fixing in repairs Gun Metal Bush (as approved) suitable for Pump Set 7.5-10 HP, complete all as specified and as directed.

Supply & fixing in repairs Gland Packing of suitable size (as approved) Pump 7.5/10 HP, complete all as specified and as directed.

Disconnecting & Dismantling Unserviceable Centrifugal Pump Set 20 HP by disconnecting from Motor, Suction and Delivery Line for carrying out repairs at Workshop by replacing following Defective Parts including Greasing replacement of Packing Sheet, Gland, Stud, Bearing, Cover Sheet & Lath Work of Impeller Shaft, etc. and Testing & Commissioning after repairs for improved performance including Transportion, complete all as specified and as directed. NOTE : New Spare Parts will be Measured and Paid separately under Item No.19 to 21. (Labour Elements is already included in this job)

Supply only Ball Bearing (as approved) suitable for Centrifugal Pump Set 20 HP, complete all as specified and as directed.

Supply only Gun Metal Bush (as approved) suitable for Centrifugal Pump Set 20 HP, complete all as specified and as directed.

Supply only Gland Packing of suitable size (as approved) suitable for Centrifugal Pump Set 20 HP, complete all as specified and as directed.

Disconnecting & Dismantling Unserviceable Centrifugal /Coupled Pump Set 40 HP by disconnecting from Motor, Suction and Delivery Line for carrying out repairs at Workshop by replacing following Defective Parts including Greasing replacement of Packing Sheet, Gland, Stud, Bearing, Cover Sheet & Lath Work of Impeller Shaft, etc. and Testing & Commissioning after repairs for improved performance including Transportion, complete all as specified and as directed. NOTE : New Spare Parts will be Measured and Paid separately under Item No. 23 to 25. (Labour Elements is already included in this job)

Supply only Ball Bearing suitable for Centrifugal Pump Set 40 HP, complete all as specified and as directed.

Supply Gun Metal Bush suitable for Centrifugal Pump Set 40 HP, complete all as specified and as directed.

Supply Gland Packing suitable for Centrifugal Pump Set 40 HP, complete all as specified and as directed.

Repair/Overhauling of Submersible Pump Set 15 HP including replacement of Unserviceable Parts as required, complete all as specified and as directed. NOTE : New Spare Parts will be Measured and Paid separately under Item No. 27 to 29. (Labour Elements is already included in this job)

Supply only Bowels suitable for Submersible Pump Set 15 HP, complete all as specified and as directed.

Supply only SS Impeller suitable for Submersible Pump Set 15 HP, complete all as specified and as directed.

Supply only Stainless Steel Bush suitable for Submersible Pump Set 15 HP, complete all as specified and as directed.

Supply and fixing in repairs Thrust Bearing suitable for Submersible Pump Set 15 HP, complete all as specified and as directed.

Repair/Overhauling of Submersible Pump Set 20 HP including replacement of Unserviceable Parts as required, complete all as specified and as directed. NOTE : Bearing, Bush & Impeller will be measured and paid separately under relevant items. (Labour Elements already included in this job)

Supply only Bowels suitable for Submersible Pump Set 20 HP, complete all as specified and as directed.

Supply only SS Impeller suitable for Submersible Pump Set 20 HP, complete all as specified and as directed.

Supply only Stainless Steel Bush suitable for Submersible Pump Set 20 HP, complete all as specified and as directed.

Supply only Thrust Bearing suitable for Submersible Pump Set 20 HP, complete all as specified and as directed.

Repair/Overhauling of Submersible Pump Set 25 HP including replacement of Unserviceable Parts as required, complete all as specified and as directed. NOTE : Bearing, Bush & Impeller will be measured and paid separately under relevant items. (Labour Elements already included in this job)

Supply only Bowels suitable for Submersible Pump Set 25 HP, complete all as specified and as directed.

Supply only SS Impeller suitable for Submersible Pump Set 25 HP, complete all as specified and as directed.

Supply only Stainless Steel Bush suitable for Submersible Pump Set 25 HP, complete all as specified and as directed.

Supply only Thrust Bearing suitable for Submersible Pump Set 25 HP, complete all as specified and as directed.

Repairing Mono Block Pump 1 HP/ 2 HP including providing new Capacitor, Seal, Washers, Impeller, etc. as required at Site, complete all as specified and as directed. NOTE :- (a) Cost of new Capacitor, Seal, Washers, Impeller, etc. shall deem to be include in the Quoted Unit Rate. (b) Bearing & Bush will be measured and paid separately under relevant item. (Labour Elements is already included in this job)

Supply only Bearing suitable for Mono Block Pump 1 HP/ 2 HP, complete all as specified and as directed.

Preparing Old Painted/treated Surfaces of Pump Sets and Motors of any description including cleaning of Grease/Oil Spots, etc. from the Pump Sets and Motors and applying Two Coats of Synthetic Enamel Paint and re-writing SM No. and MES No. on Pump Sets and Motors of suitable size, complete all as specified and as directed.

Taking out Pumping Set for repair from Bore Well by dismantling Suction/ Delivery Column Pipe 50mm to 150mm dia and Lowering the Column Pipe after repairing the Pump including replacement of Gasket Set, worn out/ damaged Nuts and Bolts of required size carefully without causing any damage to the Pumping Set, Submersible Cable, complete all as specified and as directed. NOTE : Job for taking out the Pumping Set consisting a Set of Pump & Motor shall be Paid for ONE Unit.

M&L Development to Existing Borewell 150mm dia by Reboring with High Speed Pneuamatic Drilling of 150mm dia to a Depth not exc. 150.00 METRE including Flushing Out and Desilting complete Borewell so as to be obtain Clean/Clear Water, complete all as specified and as directed. NOTE: DG Set with Fuel and Pump Set will be arranged by the Contractor at his own arrangement and Quoted Rate deem to be include for the same.

Supply, fixing & Lowering GI Column Pipe 50mm bore (dia), 3.00 METRE in Length, medium grade, ISI marked, both End Flanged with Rubber/ Fibre Joints with Mild Steel Bolts, Nuts, & Washers, etc. including Taking down/ out unserviceable Column Pipe, complete all as specified and as directed.

Supply, fixing & Lowering GI Column Pipe 80mm bore (dia), 3.00 METRE in Length, medium grade, ISI marked, both End Flanged with Rubber/ Fibre Joints with Mild Steel Bolts, Nuts, & Washers, etc. including Taking down/ out unserviceable Column Pipe, complete all as specified and as directed.

Supply, fixing & Lowering GI Column Pipe 100mm bore (dia), 3.00 METRE in Length, medium grade, ISI marked, both End Flanged with Rubber/ Fibre Joints with Mild Steel Bolts, Nuts, & Washers, etc. including Taking down/ out unserviceable Column Pipe, complete all as specified and as directed. NOTE: Contractor will be liable to restore the water supply same day after repairing of Pumps or replacing of pipelines(any type) or arranging of any other methods to restore water supply. He is also liable to arrange to prevent Water leakage from the disturbed pipe lines temporariliy to execute the works within a stipulated period as directed by Engr in Charge.

M&L Cross Arms, Bracings, Supports, Clamps and Back Plates fabricated from Structural Steel Section including Nuts, Bolts, Washers and necessary welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of One Primer Coat, One Under Coat and One Finishing Coat of Synethtic Enamel Paint, complete all as specified and as directed.

Removing the U/S contactors 25 Amps, Supply & Fix 3 phase, 3 pole power contactor, 415V, suitable motor starters for the following AC3 ratings.

All as per item No. 50 but for 40 Amps

All as per item No. 50 but for 50 Amps

All as per item No. 50 but for 70 Amps, Type MNX 70

All as per item No. 50 but for 18 Amps, Type MNX 18

All as per item No. 50 but for 9 Amps, Type MNX 9

Removing the defective over load 9 -13A relay range relays and S&F new bi metal over load relay for motor starter suitable for Star Delta stareters, directly mounting following relay range all as specified.

All as per item No. 56 but for 12-18A relay range.

All as per item No. 56 but for 30-40A relay range.

All as per item No. 56 but for 80 -93A relay range.

Removing the U/S single phase preventor, Supply & Fix Single phase preventor suitable for 3phase pump sets of any capacity, Make : Minilec/L&T all as directed.

S&F MCCB 63 Amp, 3 Pole, 415 Volt, 50 Hz, 25 kA with necessary Connections with Thimbles, etc. including Taking down/out unserviceable MCCB, complete all as specified and as directed. NOTE : MCCB should be Adjustable Thermal & Fixed Magnetic setting. Make - Havells Cat No. IHLAST0063 or equivalent Make as shown in list of Makes.

S&F MCCB 100 Amp, 3 Pole, 415 Volt, 50 Hz, 25 kA with necessary Connections with Thimbles, etc. including Taking down/out unserviceable MCCB, complete all as specified and as directed. NOTE : MCCB should be Adjustable Thermal & Fixed Magnetic setting. Make - Havells Cat No. IHLAST0100 # or equivalent Make as shown in list of Makes.

S&F MCCB 200 Amp, 3 Pole, 415 Volt, 50 Hz, 25 kA with necessary Connections with Thimbles, etc including Taking down/out unserviceable MCCB, complete all as specified and as directed. NOTE : MCCB should be Adjustable Thermal & Fixed Magnetic setting. Make - Havells Cat No. IHLANT0200 # or equivalent Make as shown in list of Makes.

S&F Loadline MCCB Enclosure with 63 Amps MCCB FP, 415 volt, 50 Hz including Taking down/out Unserviceable Loadline Enclosure, complete all as specified and as directed CAT No.IHEATP of Havells/ L&T/ Indo Asian Equivalent as approved by GE NOTE : All MCCB should be Adjustable Thermal and Fixed Magnetic setting.

Supply & Installation of Fully Automatic Star Delta Starter, 25 HP with Overload Relay Range 17-25 Amp, 415 Volt, 50 Hz suitable for Pump Set upto 25 HP comprising with the following Spare Parts including Taking down/out Unserviceable Star Delta Starter, complete all as specified and as directed :- (a) Contactor 32 Amps capacity - 3 No. (b) Auto Relay Range upto 25 Amp - 1 No. (c) Automatic ON/OFF Switch - 1 No. (d) Timer - 1 No. (e) Singal Phase Preventar - 1 No. MAKE : HAVELLS Cat No. IHPASDQD* or equivalent of BCH/L&T

S&F in replacement of unservicable DOL STARTER with control wirings complete suitable for 7.5 HP motor 3 phase 415 V AC 50 HZ with relay range 11-18 Amps Including connection & testing complete. Make- L&T Model- MK1 DOL Cat No.SS96211 or equivalent in Havells & BCH

S&F in replacement of unservicable DOL STARTER with control wirings complete suitable for 10 HP motor 3 phase 415 V AC 50 HZ with relay range 15-25 Amps. Including connection & testing complete. Make- L&T Model- MU1 DOL # Cat No.SS95647 or equivalent in Havells & BCH

S&F replacement of unservicable DOL STARTER with control wirings complete suitable for 2 HP motor SP, 230 V AC 50 HZ with relay range 10.5-17.5 Amps. Including connection & testing complete. Make- L&T Model- MF1 Cat No.SS97227OOBO or equivalent in Havells & BCH

S&F Pressure Gauge 0-10 Kilogram/Cm², having 65mm dia including necessary Fittings/Accessories for fixing including Taking down/ out unserviceable Pressure Gauge, complete all as specified and as directed.

Supply & laying Flat Copper Cable insulated, PVC Sheathed Water Proof, conforming to IS-694, 1100 Volt Grade suitable for Submersible Pump Set, Cross-sectional area 6.0 Sqmm, 3 Core including taking down/out unserviceable Cable, complete all as specified and as directed.

Supply & laying Flat Copper Cable insulated, PVC Sheathed Water Proof, conforming to IS-694, 1100 Volt Grade suitable for Submersible Pump Set, Cross-sectional area 10 Sqmm, 3 Core including taking down/out unserviceable Cable, complete all as specified and as directed.

Supply & laying Flat Copper Cable insulated, PVC Sheathed Water Proof, conforming to IS-694, 1100 Volt Grade suitable for Submersible Pump Set, Cross-sectional area 25 Sqmm, 3 Core including taking down/out unserviceable Cable, complete all as specified and as directed.

Dismantling of Concrete in Ground Floors and Paving not exc. 15 cm thickness (below or above Ground Level), complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including necessary formwork as required at Site(s), complete all as specified and as directed.

Excavating in trenches, not exc. 1.50 m Wide and depth not exc. 1.50 m for taking out/up and laying of Water Main /Pipe, etc., for foundation, etc. and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Surplus Soil providing Heaps along the route of the Pipe Line in Soft/Loose Soil, complete all as specified and as directed.

M&L Making Hole Under Road and Hard Standing including Cutting, etc. with Manual Auger or Bookie dia not exc. 150mm dia for laying Pipe Line, etc., complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.3mm thick burried directly in Ground (Earth Pit not less than 2.25 Metre below Ground Level) with Top edge of the Plate not less than 1.50 Metre below Ground Level, connected with and including Galvanised Earth Strip of size 25x4mm by means of Bolts, Nuts, Check nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar with GI 40mm bore (dia) light grade Protection Pipe, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc. 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, Funnel with GI Watering Pipe 20mm bore (dia) medium grade including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including Taking out unserviceable Earthing of any description, complete all as per specified and as directed.

M&L Galvanised Iron Strip 25x4.0mm with Saddles and fixing Screws for Roof/ Earth Conductors and Down Conductors above Ground all Joints should be connected by Exothermic Welding or Brazing including Taking down Unserviceable Strip, complete all as specified and as directed.

Taking up or down Steel/CPVC/PVC Tubing 15mm bore (dia) with Fittings/ Connections, complete all as specified and as directed.

All as per item No. 81 above but of size 20mm.

All as per item No. 81 above but of size 25mm.

All as per item No. 81 above but of size 40mm.

All as per item No. 81 above but of size 50mm.

All as per item No. 81 above but of size 80mm.

All as per item No. 81 above but of size 100mm.

Supply & laying Steel Water Tubing 15mm bore (dia), Galvanised, 'medium grade' with all Fittings, laid in trenches any other sitution, complete as all specified and as directed.

All as per item No. 88 above but of size 20mm.

All as per item No. 88 above but of size 25mm.

All as per item No. 88 above but of size 40mm.

All as per item No. 88 above but of size 50mm.

All as per item No. 88 above but of size 80mm.

All as per item No. 88 above but of size 100mm.

S&F Gun Metal Gate Valve 15mm bore (dia), ISI marked, heavy duty, Half round handle type including all Fittings required at Site and Fixed-in-repairs, complete all as specified and as directed.

All as per item No. 95 above but of size 20mm.

All as per item No. 95 above but of size 25mm.

All as per item No. 95 above but of size 50mm

S&F Ball Valve 15mm bore (dia), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic float, screwed for Iron Pipe and fixed-in-repairs, complete all as specified and as directed.

All as per item No. 99 above but of size 25mm

All as per item No. 99 above but of size 40mm

S&F Rotational moulded polyethylene / HDPE water storage tanks, ISI Marked, of capacity 1000 Ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I alongwith necessary fittings / connections incl taking down old u/s storage tanks all as directed.

Supply & fix, Bib tap, Fancy Type, cast copper alloy with chromium plated, Heavy duty of Size 15mm incl taking down old unserviceable Bib tap all as directed.

M&L DI pipe fitting like Bends (any type, radius and angle) Tapers any type, (Straight, Bend, Increasing, Decreasing or Double Socket, etc.) Tee Pieces Single Branch, ‘Y’ Junction, Double Branch, Cross (all Sockets or Socket and Spigot) Collars, Caps and Plugs upto 200mm bore (dia) including removing damaged Cast Iron Fittings, complete all as specified and as directed.

Repairing damaged/broken CI/GI/DI/Thin Wall Pipe Line of Size 80/100mm bore (dia) including loose Colar, Lead/Clamp Joint required to replace the damaged/ broken Pipe Line to Stop the Leakage including necessary Earth Work as per Site requirement, complete all as specified and as directed. NOTE : - Making Good of Disturbed Surfaces with using Cement Concrete 1:4:8 type D2, using 40mm graded stone aggregate) where required/ordered complete will be measured and paid separately.

All as per item No. 105 above but of size 150/200mm

Taking up or down CI/DI Pipe 100mm bore (dia) with Fittings/ Connections, complete all as specified and as directed.

All as per item No. 107 above but of size 150mm

All as per item No. 107 above but of size 200mm

Supplying, laying, jointing and testing Ductile iron (DI) pipe of size 100 mm dia with spigot/ socket ends centrifugally cast type K-7 ISI marked in any length, laid in trenches and connected to existing pipe line as required at site complete with jointing material (Rubber tyton joints) all as specified and directed.

All as per item No. 110 above but of size 150mm

All as per item No. 110 above but of size 200mm

Supply, fixing and testing sluice valve of size 150 mm dia marked IS marked PN 1.6 cast iron, flanged both ends and drilled for jointing rubber packing 3 mm thick with bolts nuts, washers including taking down old sluice valve complete all as specified and directed.

All as per items 113 above but 100 mm dia.

All as per items 113 above but 80 mm dia.

Supply Fix & testing CI NRV horizontal 150 mm dia ISI marked in suction pipe line of pumping set including nut, bolts, washers etc as required at site including taking down old US non return valve complete and fixed in repair all as specified and directed.

All as per items 116 above but 100 mm dia.

Supply Fix & testing Cast Iron Body with Rubber Ball Type Foot Valve, Heavy Duty 150mm incl taking down old u/s Foot Valve all as directed.

All as per item No 118 above but of size100 mm

All as per item No 118 above but of size 80 mm

Supply only Chlorination testing glass test Tube kit with testing solution complete.

Preparing Old Painted/treated Steel Surfaces of Valve Pit/ Chamber Covers, Cast Iron Pipes, etc. and applying Two Coats of Synthetic Enamel Paint over a coat of Red Oxide Zinc Chrome Primer, with writing of Valve/PIT No. & Location of suitable size complete all as specified and as directed.

Supply & fix in repairs Gun metal Air release valve suitable for any type Monoblock/Coupled pump set complete.

S&F in repairs of Analog Volt meter Class 1, 3Ph, 415 Volt complete all as directed.

S&F in repairs of Analog Ammeter Class 1, 3Ph, 415 Volt complete all as directed.

S&F LED aviation obstruction light (Red) with suitable size GI pipe bracket complete all as specified and directed by Engr-in-charge. Make :Bajaj, Model No. BGAV 302 LED or equivalent Make as shown in list of Makes.

Taking down carefully existing unsv. cable from Over Head tank & S&F PVC Round FR copper cable 3 core 1.5 sq mm, ISI marked with suitable clamps. Note:- All T&P & ladder required for carrying out work will be arranged by the contractor and nothing extra will be admissible on this account.

Supply and fix PVC / FRP enclosure, 240V, AC, 2 way, double door complete all as specified and directed.

S&F MCB SPN 6 to 32A, AC, 240V, 10KA,complete all as specified and directed.

Collecting the sample of water of following Borewell/Pump House and taking it to state Govt. PHED/ Regional laboratory for testing and submitting the test report:- (a) Acquire land borewell. (b) Borewell at Zhopra Complex (c) Main Pump House (d) RO Plant

S&F Multi port valve of size 40mm bore suitable for RO plant incl taking down old one complete.

Supply only CHLORINE 65%-70% calcium based granular, disinfectant for potable water treatment, packing in 40 / 45 Kg plastic drums.

M&L Taking out carefully Water meter fitted with 300mm dia DI Pipe using chain pulley and keep in safe custody for refixing after repairing of leakage DI Pipe by replacing of gasket and DI tail piece 300mm dia -01 No one end spigot and one end flanged)

Taking up or down Steel Tubing /Cast iron pipes 80/100mm bore (dia) with Fittings/ Connections, segregating Serviceable Pipes and Fittings/ Connections and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing /Cast iron pipes 150mm bore (dia) with Fittings/ Connections, segregating Serviceable Pipes and Fittings/ Connections and keep in Safe Custody for re-use, complete all as specified and as directed.

Relaying/fixing old GI/CI/DI pipe 80/100mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 134 here-in-before) in New or Old Position (i.e. laid in Trenches/Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of new GI/CI/DI Connections (as required at Sites), complete all as specified and as directed.

Relaying/fixing old GI/CI/DI pipe 150mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 135 here-in-before) in New or Old Position (i.e. laid in Trenches/Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of new GI/CI/DI Connections (as required at Sites), complete all as specified and as directed.

AUTOMATION SYSTEM (Existing OEM-RDS)

Servicing of Motorised Butterfly Valve 150mm incl removing, cleaning, greasing, checking for wear and tear, refixing, testing, installing, commissioning all as directed.

Servicing of Motorised Butterfly Valve 80/100mm incl removing, cleaning, greasing, checking for wear and tear, refixing, testing, installing, commissioning all as directed.

S&F in repair of Electric motor suitable for actuator for 80mm dia Butterfly valve all as directed. Make: RITE TORK

S&F in repair of Electric motor suitable for actuator for 100mm dia Butterfly valve all as directed Make: RITE TORK

S&F in repair of Electric motor suitable for actuator for 150mm dia Butterfly valve all as directed. Make: RITE TORK

S&F in repair of M.S. Spiral gear Suitable for Existing RITE TORK gear box of actuator for 80mm dia Butterfly valve all as directed.

S&F in repair of M.S. Spiral gear Suitable for Existing RITE TORK for gear box of actuator for 100mm dia Butterfly valve all as directed.

S&F in repair of M.S. Spiral gear Suitable for Existing RITE TORK for gear box of actuator for 150mm dia Butterfly valve all as directed.

S&F in repair of Butterfly valve of size 80 mm dia for acutator all as directed. As per Existing Make AUDCO/VIRGO/INTERVALUE

S&F in repair of Butterfly valve of size 100 mm dia for acutator all as directed. As per Existing Make AUDCO/VIRGO/INTERVALUE

S&F in repair of Butterfly valve of size 150 mm dia for acutator all as directed. As per Existing Make AUDCO/VIRGO/INTERVALUE

S&F in repair of Capacitor for Actuator suitable for 80 to 150mm dia Butterfly Valve all as directed.

S&F in repair of Resistor for Actuator suitable for 80 to 150mm dia Butterfly Valve all as directed.

S&F in repair of Hand Wheel for Actuator suitable for 80 to 150mm dia Butterfly Valve all as directed.

S&F in repair of Limit Switch for Actuator suitable for 80 to 150mm dia Butterfly Valve all as directed.

S&F in repair of Top Cover for Actuator suitable for 80 to 150dia Butterfly Valve all as directed.

S&F in repair SMPS Input Voltage: 230 V, Output Voltage: 24 V all as directed. As per Existing Make NHP/TELEMECHANIQUE

S&F in repair of Transformer Input voltage: 230V AC, Output voltage: 12V AC all as directed.

S&F in repair of MCB 3P, 10 to 20A all as directed.

S&F in repair of 5 pair 0.5Sqmm Armoured Communication cable all as directed. As per Existing Make FSC/ POLYCAB/ DELTON

S&F in repair of 2 Core 1.5Sqmm Armoured cable. As per Existing Make POLYCAB/PRIMECAB/FINOLEX

S&F in repair of 4 Core 1.5Sqmm Armoured cable. As per Existing Make POLYCAB/PRIMECAB/FINOLEX

S&F in repair of 6 Core 1.5Sqmm Armoured cable. As per Existing Make POLYCAB/PRIMECAB/FINOLEX

S&F in repair of LED Indicators of Colour : Red / Yellow / Blue all as directed.

Supply & fixing in repairs of Single phasing preventer - VSP D2.

Supply & fixing in repairs of Pressure switch 0 - 10 kg/sq.cm. As per Existing Make DANFOFOSS /INDFOSS/ HONEYWELL

Supply & fixing in repairs of Relay– 4 C/O, 24 V D.C./230 VAC, As per Existing Make IDEC/LEONE

Supply & fixing in repairs of Push Button with LED Indicator-240VAC Color : Red / Green, As per Existing Make TELEMECHANIQUE/SCHNEIDER

Supply & fixing in repairs of GPRS communication modem and PLC based GPRS gateway hardware along with suitable communication card communication Modems. Modem Should be fixed inside PLC based panel with proper connections.Modem suitable for existing RDS automation system as per Existing Make MAESTRO/HERITAGE/LEO

YOGINDER KUMAR GUPTA AND COMPANY