CA NO.CWE BLY/GE (W)/79 OF 2026- 2027REPAIR TO ROAD AND PATHWAY IN CERTAIN AREAS UNDER AGE B/R-I UNDER GE (WEST) BAREILLY

M&L for repair to pot holes any depth, not exc 1 Sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) and making good by applying tack coat with bituminous primer VG-10 @ 5 Kg per 10 Sq m, putting in premix bituminious macadam, well rammed and sealed with premixed sand seal coat (9.8 kg of binder with 0.09 Cum of stone chipping, 6.3mm size), again well rammed (including supply of premixed macadam, binder and chipping) depth of potholes not exc 30 mm complete all as specified and directed.

M&L for scarifying or picking gravelled,macadam or bituminous macadam surfaces in area exc n 400 sqm, n.exc 50mm deep all as specified

M&L for applying evenly a priming /tack coat with paving bituminous VG-10 grade at 5 Kg/10 Sqm complete all as specified and directed.

Supplying, laying, spreading upto 75mm or less consolidated thickness of premix bituminous macadam carpet filling in depression (using 20mm graded stone aggregate) in single layer using mechanical paver using bituminous binder (VG-30) at the rate 4% by weight of total mix, laid/rolled and compacted/consolidated to required camber and gradient with 8 to 10 tone power roller to a uniform smooth surface complete all as specified and directed.

M&L for Preparing of black top bituminous surfaces by brushing with brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with air pressure through air jet using air compressor to remove all loose dirt etc incl removing mud etc to a distance minimum 1.50m from edge of road and applying evenly a tack coat of bituminous primer using paving bitumen (VG-10) at the rate of 5 Kg per 10 Sqm of road surface by sprayer operated hot pressure mechanisum, supplying, laying, spreading 30mm consolidated thickness of semi dense asphaltic bituminous concrete carpet (VG-30) with 0.406 cum crushed and graded coarse aggregates with design mix formula with bitumen not less than 5.5% binder content using paver with mechanical paver all as specified in clause device for automatic leveling and profile control within the specified tolerance as mentioned in SSR Part-I , rolled with 8 to 10 tone powar Roller to uniform smooth surface and consolidated to required camber and gradient with power roller for uniform smooth surface complete all as specified and directed. Note: (i) Design mix for SDAC shall be carried out through an authorised testing lab and the cost of testing shall be included in quoted rate. (ii) Aggragates for Bituminous works shall confirm to clause No 20B 2.5 of SSR, 2009 Part-I (Specifications) with the following constraints:- Aggregate passing 13.2 mmIS Seive- 100% Aggregate Passing 5.60mm IS Seive- 40% to 50% Aggregate passing 2.8mm IS Seive- 30% to 35% Note for item No 3 & 4 Based on job formula , in case the binder content (i.e. Bitumen)is less than the content specified under these items then a minus adjustment @ 40/- per Kg of bitumen (less consumed ) shall be appllied on the quoted rate of contractor against these items , hence the qouted rate of contractor shall be reduced based on less content of bitumen required as per job mix formula. However, no price adjustment on plus side shall be made for increase of quantity of bitumen in case of required as per job mix.

Material and labour for painting lines, dashes, arrows letter, marking etc of 2mm thick film on new surface or previously treated road surface with hot applied retro-reflective thermoplastic exc 10 cm wide n exc 15cm wide road marking paint (white/golden/yellow) conforming to MORTH (Clause 803.4) all as specified with 8% glass beads using special applicator machine with heating arrangement upto 160°C including cleaning and drying the existing road surfaces to ensure dust, oil, grease and moisture free surfaces before applying the paint complete all as specified and directed.

S&F in repair Cat eye,Solar reflective type of metal body alloy of size 110mmx128mmx30mm of red / yellow / white with PAMA striplens reflector of Model -DA 971 fixed with 100 gm epoxy mixture and placing the cats eye without applying excessive pressure and fixed as per manufacturers instructions complete all as specified and directed.

S&F in repair solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. all as specified and directed,

S&F in repair metal rectangular delineator post made out of 2 mm thick MS sheet rectangular OD size 75x100mm of length 1200mm. Bottom plate 2 mm thick of size 150 x 150 mm for firm grip welded to base. Top end closed with 2mm steet sheet. All coated with heat process & baked to 120 degree centigrade or powder coated to make all waether resistant. At top and bottom sides diamond grade cube corner micro white reflector of size 75x125mm laminated in 2mm deep cavity to make it scratch resistant. Post to have two bands all around of white reflective sheet of width 225mm by keeping black coat as bands for greater night visibility and including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed.

S&F of unit/directional/road sign board made of stainless steel sheet 3 mm thick fixed on both side properly revited/welded to inner frame of stainless steel squre pipe (304 grade) of size 30mmx30mmx3mm fixed with welding to outer frame of board of size 50mmx50mmx3mm square pipe of stainless steel. Outer frame is welded to 02 Nos stainless steel Pipe of 50mm dia steel poles of 2600mm height. Retro reflective regulatory board of over all size min 1500 mm x 900mm, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved . Letter, symbols, logo, borders etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. Staiinless steel pipes should be min 14 gauge (SS 304 Gde) welded to the frame with adequate anti-theft arrangement . Board to be fixed on ground including excavation & earth work and grouting in PCC 1:2:4 type B1(20mm graded stone aggrigatge) of size 300mmx300mmx400mm deep complete all specified and directed.