Thodiyoor GP Renovation of Puthanpuramukku Nursery mukku in ward no.2 Retender

Amount

Road renovation

3.2 : Preparation of Foundation for EmbankmentScarifying Existing Bituminous Surface to a Depth of 150 mm by Mechanical MeansScarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.

4.9 : Wet Mix Macadam <br> Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. <br> By Mechanical Means with 1 km lead

75.5.1.1pb : Prime Coat - Low porosity - With Packed Bitumen Rates <br> Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

75.5.2.3pb : Tack Coat - With Packed Bitumen Rates <br> Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.9.1.2pb : 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder - Bitumen S-65 - Packed Bitumen Rates<br> Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. <br> Case - I By Manual Means <br> (II) Bitumen (S-65)

75.5.12.A.3.2pb : Seal Coat - Manual Means - Type C - Bitumen S-65 - Packed Bitumen Rates <br> Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 <br> A. By Manual Means <br> Case III : Type C <br> (II) Bitumen (S-65)

od482373/2019_2020 : Filling up low lying and waterlogged areas with local material/quarrymuck, spreading in layers,levelling the top at site and consolidation by ramming,etc complete for improving the CBR value of subgrade.

od482374/2019_2020 : Construction of un-reinforced dowel jointed at expansion and construction joint&lt;br&gt;only,plain cement concrete pavement ,thickness as per design,over a prepared sub base,with 43 grade&lt;br&gt;cement or any other type as per clause 1501.2.2 M 30 (grade),coarse and fine aggregates conforming to IS&lt;br&gt;383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2&lt;br&gt;cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side&lt;br&gt;formwork(steel channel, laying and fixing of 125 micron thick polythene film, wedges,steel plates including&lt;br&gt;levelling the formwork as per drawing),spreading the concrete with showels,rakes,compacted using&lt;br&gt;needle,screed, and plate vibrators and finished in continuous operation including provision of contraction&lt;br&gt;and expansion ,construction joints,applying debonding strips, primer, sealant, dowel bars, near approaches&lt;br&gt;to bridge /culvert and construction joints, admixtures as approved,curing of concrete slabs for 14 days,using&lt;br&gt;curing compound(where specified) and water finishing to lines and grade as per drawing and Technical&lt;br&gt;Specifications clause 1501

od482375/2019_2020 : plain cement concrete pavement ,thickness as per design,over a prepared sub base,with 43 gradecement or any other type as per clause 1501.2.2 M 20 (grade),coarse and fine aggregates conforming to IS383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side&lt;br&gt;formwork(steel channel, laying and fixing of 125 micron thick polythene film, wedges,steel plates including&lt;br&gt;levelling the formwork as per drawing),spreading the concrete with showels,rakes,compacted using needle vibrators and finished in continuous operation including provision of contraction and expansion and construction joints, admixtures as approved &amp; curing of concrete slabs for 14 days,using water finishing to lines and grade as per drawing and Technical Specifications clause 1501(without shuttering) modified 6.4

SHIHAB S

Bidder Name

Sanjayan

SHIHAB S