CA NO. CWE BLY /GE(E) / 126 OF 2021-2022 PROVN OF GUARD ROOM WITH ATTACHED TOILET BLOCK AT DHELA POST AT RTS AND DEPOT HEMPUR UNDER GE(E) BAREILLY

Amount

Surface excavation in soft/loose soil n exc 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches exc 1.5 m & n.exc 3 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n.exc 3 m in depth and getting out in soft/loose complete all as specified and directed.

M&L Cement concrete in foundations, filling and mass concrete (PCC) Type D2 1:4:8 (40 mm graded aggregate) etc complete all as specified & as directed

M&L flat form work to sides of concrete foundations, footing bases of columns, raft and raft beams, sides and soffits(if any) of foundation and plinth beams and similar work, veritical or to batter complete all as specified and directed.

M&L for RCC M-25 (Desigh mix) (20mm graded stone aggregate) for foundation including rafts, footings, foundation beams, plinth beams, bases for columns, etc, complete all as specified and directed.

M&L form work to sides of pillars posts, struts piers, columns & stanchions square rectangular or polygonal rough finished surfaces in shape complete all as specified and directed.

M&L for RCC M-25 (Design mix) (20mm graded aggregate) for columns, pillars, pierrs, posts & struts etc complete all as specified and directed.

M&L flat form work to sides and soffits of floors or roof beams haunching, girders bressumers lintel cantilevers shelves including supports, overhangs etc also splays between floors and beams etccomplete all as specified and directed.

M&L for RCC Design Mix M-25 (20mm graded aggregate) for beams cantilevers bressumers, lintels over 1.5m span etc complete all as specified and directed.

M&L,flat rough finished surfaces Form work to soffits of suspended slab such as roof slabs, floors slabs, landing & similar work not exceeding 200 mm thick (Horizontal or sloping) etc complete all as specified and directed.

M&L for RCC Design mix M-25 (20mm graded aggregate) for slab supported on walls, beams and columns in floors, roofs, landings balconies canopies, deck slab and in shelves complete all as specified and directed.

M&L for form work to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in valls etc rough finished surfaces of concrete flats complete all as specified and directed..

M&F formwork to rough finished surfaces of contrete of chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for RCC design mix M-25 (20mm graded aggregate) as in chajjas all complete all as specified and directed.

M&L for DPC to horizontal or vertical surfaces including necessary form work 25mm thick PCC (1:2:4) Type B0 (12.5mm graded aggregate on plinth beam including mixing of water proofing compound as per manufacturers instructions and necessary form work complete all as specified and directed.

M&L brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed..

M & L for brick work with fly ash sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete complete all as specified and directed.

M&L rendering 15mm thick 1:6 on surfaces other than fair faces of brick work or concrete surface surface finsihed even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work or concrete surface in CM 1:4, mixed with water proofing compound @ 3% by weight of cement or as per menufecturer instruction, surface finsihed even and smooth without using extra cement complete all as specified and directed. WPC shall be measured and paid separately.

M&L rendering 10mm thick in CM 1:3 on ceiling surface, surface finsihed even and smooth without using extra cement complete all as specified and directed..

M&L preparation of newly plastered surface of wall and applying two coat of oil emulsion distemper (white or tinned) over chalk whiting complete all as specified and directed.

M&L applying two coats cement base paint on wall including preparing new plastered surface including 3mm wall care putty complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for sand filling under floor or in foundation including watering and consolidation complete all as specified and directed.

M&L, Broken stone or boulder Hardcore of guage n exc 63 mm, deposited, spread and levelled in layers not exc 15 cm thick , watered and rammed to a true surface etc complete all as specified and directed.

M&L cement concrete 1:4:8, type D2(40mm graded stone aggregate) as in 75mm thick sub base of floor complete all as specified and directed.

M&L for cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) 25mm thick as in bedding layer for laying floor tiles complete all as specified and directed..

M&L non skid coloured ceramic tiles 7 to 8mm thick(Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or colour cement to match incl 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L machine cut mirror polished kota stone slab flooring 20-25mm thick over including 20mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment dto match the shade of the slab including round nosing at corners, rubbing and mirror polishing complete all as specified and directed.

M&L for machine cut mirror polished kota stone slab 20-25mm thick as in riser of steps, skirting, dado and pillar laid over and including 15mm thick cement screed base in CM 1:4 laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300x200x7 mm thick set and jointed in neat cement slurry and jointed in coloured cement as in vertical surfaces such as dado/skirting and facea of side bldg over & including 10mm thick rendering in CM (1:4) complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying and fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined to-gether with solvent cement as per specification complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts of extruded section of 150 mm long and fixed complete all as specified and directed.

S&F Aluminium handles, cast type, anodised of 150 mm size complete all as specified and directed.

S&F Butt hinge, Stainless steel of 100 mm size complete all as specified and directed.

S&F pressed steel frames size 115mm x 60mm for door with one or more rebates including necessary fixing lugs, hings, lock stike plate etc complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) for fixing of hold fast/filling pressed steel door frame including necessary form work complete all as specified and directed.

S&F 30mm thick flush shutters, solide core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm thick 2nd class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 and fitted to chowkats complete all as specified and directed.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 200mm long mild steel barel tower bolts of stove enamelled black with bright bolt and fixed complete all as specified and directed.

S&F 150 mm aluminium handle cast type, anodised complete all as specified and as directed.

S&F of Steel windows with pressed steel frame ( size 95x45x1.25mm) side hung shutter including box type hinges with steel handle, and steel peg steel complete with glazed openable shutter with glazing bar (open out side) and wire gauged openable shutter without glazing bar ( open in side) dovetailed or welded complete all as specified and directed and all as per Drg No TD/088 dt 07 jan 2002 Note:- (i) Two shutter ie wire gauged and glazed shall be fixed in one composite frame and both shutter shall be measured as one unit. (ii) Rate for filling of PCC in frame deemed to be included in quoted rate. (ii) MS grill shall be measured and paid seperatly under relevant item of schedule

S&F mild steel window with side hung shutter incl projecting type hinges with steel handle and steel peg stay complete without glazingbars, dovetailed or welded complete all as specified and directed..

S&F for steel ventilators fixed type, with glazing bars complete welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed . (Note :- Glass shall be measured and paid for separately).

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified and directed.

S&F 3.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F mild steel sliding door bolts, 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

Preparation of new wooden surface of any description and applying two coat of synthetic enamel paint over a coat of pink primer over 10cm width or girth complete all as specified and directed.

S&F framed work such as grill grating etc with end of bars shouldered and/or riveted welded or forged into spikes framed guard bars iron doors ladders framed bullesters walk ways railings, frame work of water tanks and similar work confirming to Fe-410 complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work or concrete surface in CM 1:4, mixed with liquid water proofing compound @ 3)% by wt of cement as per manufacturers insts, finished the surface even and smooth without using extra cement complete all as specified and directed.. WPC shall be measured and paid separately.

M&L for preparation of roof surface and applying a coat of hot bitumenous primer @ 0.40 Kg/sqm and applying a coat of industrial bitumen 85/25 grade @ 1.20 Kg/sqm, supplying and laying water proofing treatment with using polymeric water proofing membrane (weight not less than 3kg/sqm) 3mm thick consisting 100 micron HMHDPE film centre core including applying one coat of industrial bitumen grade 82/25 @ 1.20 Kg/Sqm on top surface of membrane and torch application of membrane with 100mm overlaps at side and end lap where required and finally finished with and including a coat of aluminium paint @ 0.20 ltr/sqm as per manufacture instruction complete all as specified and directed.

Supply only integral water proofing compound.

S&F fancy type curtain rod MS conduit rod PVC coated including fancy type knob and MS bracket for hanging curtain rod complete all as specified and directed.

M&L precast cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in precast cover slabs (for manholes etc) including all use of forms moulds or machine moulds and setting the blocks, slabs etc in cement mortar 1:6 complete all as specified and directed. (Reinforcement shall be measured and paid separately under respective item of this schedule)

M&L for PCC (1:3:6) Type C1 as in plinth protection 75mm thick finished even and smooth without using extra cement all as specified and directedd.

M&L for cement concrete type B2 1:2:4 (40mm graded aggregate ) in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cment concrete using extra cement complete all as specified and directed..

S&F bib taps cast copper alloy 15mm size, crutch or butterfly handle, screwed down, screwe for iron pipe chromium plated complete all as specified and directed.

S&F of 15mm pillar taps of cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and flyne's screwed for iron pipe and fixed complete all as specified and directed.

S&F of vitreous china wash basin white, flat, back, size 550x400mm excluding tap waste but including brackets and including cutting for and pinioning in ends of brackets but exclusive of supply wate pipe complete all as specified and directed.

S&F of 15mm bore of dia concealed stop cock cast copper alloy screwed down high pressure, with cruch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed.

S&F PVC connection 15mm bore length not less than 600 mg long with both ends PTMT nuts complete all as specified and directed.

S&F angle cock 15mm bore chromium plated fancy type screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

S&F of vitreous china squatting pan orissa pattern size 580x440 mm with integral foot rest white (excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti syphonize pipe etc complete all as specified and directed.

S&F 10 ltrs PVC valveless syphonic action type flushing cistern low level white, with inlet ball valve, float and handle including bracket with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed.

S&F 125 mm size swivel shower rose brass chromium plated long body fixed complete all as specified and directed..

S&F rotational mouldred polythylene water storage tank of 1000 ltr capacity consisting of three laver (cylindrixcal vertical with top closed) hoisted and fixed in poistion including GI nipple 20mm dia fixed in water tank complete all as specified and directed.

S&F 20mm dia Ball valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule all complete all as specified and directed.

S&F 20mm bore Gun-metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 600mmx450mm bevelled adges mirror consisting of 5.5mm thick commercial plywood and fixed to plug with chromium plated brass screwed and cup washer complete all as specified and directed.

S&F towel rail 450mm long of PTMT fixed with and including chromium plated brass screw and wooden /plastic cleats(min wt 170 gms) complete all as specified and directed.

S&F shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats(min wt 300 gms) complete all as specified and directed.

S&F 125mm grating doom with waste hole of PTMT (min wt 40gms) complete all as specified and directed.

S&F 32 mm dia waste coupling of PTMT (half or full threaded) (min wt 42-45 gms) complete all as specified and directed.

S&F 32mm bore low density polythylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complte to walls, ceiling or in floors etc complete all as specified and directed.

Cutting chases for GI consealed water tubing and making good with cement sand mortar 1:3 cutting n.exc. 10cm girth complete all as specified and directed.

S&F 15mm bore GI water tubing medium grade galvanished with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified and directed.

S&F 20mm bore GI water tubing medium gared galvanished with all litting and fixed complete to walls and ceiling or laid in floor complete all as specified and directed.

S&F cast iron nahani trap with grating including jointing to waste pipe fixed in cement concete type B-1 (1:2:4) of 75mm bore complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as specified and directed.

S&F 110 mm bore PVC (SWR)vent cowl complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor tarp plain with grating incl jointing with solvent cement complete all as specified and directed.

M&L PVC (SWR) gully trap 125x110 mm setting in jointing with solvent cement complete all as specified and directed.

S&F 100mm dia stack clamp out of 50mmx5mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends with oval acces door complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends with oval acces door complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25cm in soft/loose soil complete all as specified and directed.

Removing excavated material n .Exc. 50m and depositing where directed at a level n.exc 1.50m above the sarting point in soils.complete all as specified and directed.(this soil will be filled under floor area).

M&L for forming embankmets including raising(or lowering) earth, spreading in layers n exc 30 cm thick watering, ramming/rolling and finishing to required size, shape etc, n exc. 1.5 m high from base with soils complete all as specified and directed by Engr-in-Charge. (Note : soil will be arranged by contractor within defence land area)

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for colomns hocking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for colomns hocking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and overupto and including 10mm dia in stirrups, spaces and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for colomns hocking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified.

S&F joint channel angle or tee section fixed indenpendtly without connecting plated inclung necessary cutting welding etc for cooler sand of Fe 410-W(Gde E-250) quality Ball complete all as specified and directed.

S&F rolled mild steel Fe 410(Gde-250) stairs (framed) including stingers, treades, landing, balusters, hand rails etc including cleats brackets etc complete all as specified and directed

S&F 1.60mm thick mild steel plain black sheet as in landing of MS stair case, cut to size, holes punched including round headed screws clout nails or rivets and fixed to steel frames with plain 40mm lap joints with riveted or welded seams including bending ot turning u mitred angles etc as required complete all as specified and directed.

Excavation in post holes or similar holes each n.exc. 0.50. cum, getting out returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering and removing surplus soil to a distance not exc 50m and making good surfaces complete all as specified and directed.

M&L for cement concrete type C-2 1:3:6 (40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L applying two coats of synthetic enamel paints on new steel surfaces over a cot of red oxide promer including preparation of surfaces all as specified and diected

M&L for 150mm bore salt glazed stone ware drains pipes laid in trenches and jointed complete all as specified and directed.

M&L for concrete bed to drain pipes in cement concrete 1:3:6 type C-2 including packing under and haunching against the sides of pipes after they are laid and tested bore of pipe 150mm complete all as specified and directed

M&L for providing cement concrete type C-1 1:3:6 (20mm graded aggregate) as in copings etc complete all as specified and directed.

S&F 4.8mm thick frosted sheet glass, ordinary quailty and glazing with oil putty in square n.exc. 0.5 Sqm in each pane complete all as specified and directed

S&F Reinforced concrete pipes class NP3 of 200mm dia laid and jointed complete with collars complete all as specified and directed.

M&L for construction of 10 users Septic tanks excavation in ordinary soil, foundation in PCC 1:2:4 brick work in CM 1:4,, RCC cover slab including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame vent shaft and sludge chambers etc as per TD Drg No- 217 amended upto date complete all as specified and directed.

M&L for Construction of soak well size 1.8m dia and 4.50m deep, excavation in any type of soil, PCC in foundation 1:4:8 brick work in CM 1:6, walls of honey combed masonry, RCC cover slab, filled with brick bats as per TD Drg No -309 amended upto date complete all as specified and directed.

M&L for PCC (Type B-1 1:2:4 using 20mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses lacing courses, parapets and railings upto 60 cm in height copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water throughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for PCC 1:3:6, type C-2 using 40mm greaded stone aggregates as in sub base flooring 100 mm thick for receiving of floor finishes etc complete all as specified and directed.

M&L for Machine pressed cement concrete factory made coloured glazed interlocking paver block any shape and size confirming to IS 15658 -2006 of 80mm thickness, M-40 Grade, machine pressed of pattern and colour, laid over and including layer of sand cushion not less than 25mm thick set and jointed with sand in hard standing complete all as specified and directed.

E&M Part: M & L for point wiring with 1.5 Sqmm cable, PVC unsheathed and insulated copper multistranded conductor, FRLS 1100 Volts grade cable (red colour cable to be used for live connection and black colour cable to be used for neutral connection) controlled by one way switch down through and including PVC concealed conduit with all accessories including 1.0 Sqmm copper multistranded conductor FRLS 1100 Volts grade unsheathed PVC insulated (green colour) continuity earth wire connected to common earth dolly and sunk cast pressed steel terminal box made out of MS sheet 1.25 mm thick for mounting of fittings like switch , socket and fan regulator with 3 mm thick hylum laminated sheet cover including cutting Chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and as directed for one light/fan/bell point controlled by one switch/bell push complete all as specified and directed.

All as per item No 114 here-in-before but for 3 Pin, 5 Amps socket outlet point on independent board.

All as per item No. 114 above but one 3 Pin, 5 Amps, switch socket outlet point controlled by one switch on the same board with other switch.

All as per item No 114 here-in-before but with 2.5 Sqmm, PVC insulated, sheathed cable and 2.5 Sqmm cable for earth wire for one 5 Pin socket out let 15 Amps.

S&F Switch, Piano, flush type, polycarbonate, 5 Amps, Single Pole, One way complete all as specified and directed.

S&F Switch, Piano, flush type, polycarbonate, 15 Amps, Single Pole One way complete all as specified and directed.

S & F Socket outlet, polycarbonate, 2 in 1, 3 Pin Amps, 5 Pin, multipurpose, flush type complete all as specified and directed.

S & F Socket outlet, polycarbonate, 2 in 1, 3 Pin Amps,15 Pin, multipurpose, flush type complete all as specified and directed.

S&F of ceiling rose PVC polycarbonate, isolated body, 3 terminals AC 230 volt complete all as specified and directed.

S&F Lamp Holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F Lamp LED Retrofit lamp, 9W LED Bulb, B22, white complete all as specified and directed. Cat No LTHPLED LAMP9 WB22 BULB of C&S or equivalent madel manufactured by Philips/Wipro.

S&F Ceiling fan, 1200mm Sweep complete with all accessories such as rubber reel, split pins, check nuts, fan blades, PVC conopy, fan clamps, capacitor, PVC connector etc. and suitable electric connection with three core flexible PVC insulated copper conductor (multistranded) cable of 1.0 Sqmm from ceiling rose to fan complete all as specified and directed.

S&F of Exhaust fan 300 mm sweep, steel body, AC, 230 volts with louvres,900 RPM including making suitable size hole in the wall for air flow and grouting of nuts, bolts and washers including electric connection with three core flexible PVC insulated copper conductor multistranded cable of 1.0 sqmm from ceiling rose complete all as specified and directed.

Supply install test & commissioning of water heater (geyser) of 25 ltrs capacity including provision of grouting nut, bolts/ washers for fixing geysers complete with water supply connections with GI tubing & electric connections complete all as specified and directed.

S&F LED Tube light fittings 1X/10 Watt,(T-8) 2' long 220V, AC decrotive box type with driver holder including LED tube light connecting up with three core flexible copper conductor cable of sutaible size from ceiling rose complete all as specified and directed.

S&F LED Tube light fittings 1X/20 Watt,(T-8) 4' long 220V, AC decrotive box type with driver holder including LED tube light connecting up with three core flexible copper conductor cable of sutaible size from ceiling rose complete all as specified and directed.

S&F LED building security light fitting 35 Watt, 230Volt, AC outdoor type with high pressure die cast aluminium housing and heat resistance polycorbonate cover complete with driver, lamp and IP-65/66 protection complete all as specified and directed.

S&F MCB, DB, TPN, 8 way, 240 volts, double door with 200 Amp rated bus bar complete all as specified and directed.

S&F MCB, DB, TPN, 4 way, 240 volts, double door with 200 Amp rated bus bar complete all as specified and directed.

S&F MCB, SPN, upto 63Amps 240V, 10kA, B curve complete all as specified and directed.

S&F MCB, SP, upto 40A, 240V, 10kA, B curve complete all as specified and directed.

M&L for sub main wiring with 2 run of FRLS PVC insulated & unsheathed, multistranded copper conductor of nominal cross sectional area 6.0 Sqmm alongwith one run of FRLS, PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 Sqmm as earth continuity conductor drawn through & including PVC conduit of suitable dia.complete all as specified & as directed. Note : 2 runs of wire + 1 run of earth wire + 1 run of PVC conduit shall be measured as one unit

Supply and laying bricks old size, well burnt sub class 'B' bricks as in protection cover for under ground cable laid width wise across the cable adjoining each other, laid dry complete all as specified and directed.

M&L for dry river sand cushioning for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top ebdge of cable after laying and punning up to 18 cm depth complete all as specified and directed. Note ;- For payment purpose the punned down thickness of 18 cm only shall be considered.

M& L for Boring holes under road or cutting the road /pavement /hard standing or any other situation by mechanical or other means for inserting 40mm bore GI pipe for crossing the cable and making good both the ends complete all as specified and directed.

S&F galvanized iron pipe of 25mm bore, Light grade with all fittings for cable protection for road crossing/ culvert/ path/ on wall/ floor/ pole or laid in floor complete all as specified and directed.

Supply, lay, joint, test and commisioning LT, XLPE insulated, screened, PVC bedded, armoured, heavy duty, electric cable 3.5 Core 25 Sqmm cross sectional area with stranded aluminium conductor, 1100 Volts grade with cable lugs including taking down of existing cable complete all as specified and directed.

Supply, lay, joint, test and commisioning LT, XLPE insulated, screened, PVC bedded, armoured, heavy duty, electric cable 2 Core 10 Sqmm cross sectional area with stranded aluminium conductor, 1100 Volts grade with cable lugs including taking down of existing cable complete all as specified and directed.

Supply, lay, joint, test and commisioning LT, XLPE insulated, screened, PVC bedded, armoured, heavy duty, electric cable 2 Core 4 Sqmm cross sectional area with stranded aluminium conductor, 1100 Volts grade with cable lugs including taking down of existing cable complete all as specified and directed.

S&F LED Flood lingh 170 Watt 220 volts 50 HZ outdoor type with thermal management in lultiple optics and equipped with IP-66 protection with impact and corrosion resistant complete all as specified and directed.

S&F LED solar street fitting 24 Watt including galvanised steel pole in built solar panel, lithium ion battery, PVC battery box, charger controller with susk down sensor, PVC wire etc including required earth work & PCC work complete all as specified and directed.

M & L for cutting existing steel tubing and inserting suitable GI fittings etc for alterations/addition the branch connection complete.

Supply & laying 25mm bore GI pipe medium grade including fittings complete all as specified and directed.

Supply & laying 20mm bore GI pipe medium grade including fittings complete all as specified and directed.

Supply & fix gun metal gate valve with Iron wheel head, screwed both ends for pipe 25 mm bore complete all as specified and directed.

Supply & Stop valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for pipe 20 mm bore complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6. mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metres below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts,check nuts, nuts and washers of GI or steel all as shown in electrical plate No 5 of SSR-I 2009. GI wire protected by GI pipe light grade 15mm dia connected to earth test point including excavation in any type of soil, returning filling, disposal of soil, earthing pit in PCC (1:3:6) type C1,RCC (1:2:4) type B1 precast cover slab with one handle made out of 8 mm dia round bar,20 mm dia (medium grade) watering pipe and providing layer of charcoal or coke and salt in alternative layers complete as specified or directed & including testng on completion complete all as specified and directed.

M&L for earthing complete with galvanised iron steel earth plate of size 600 x 600 x 6 mm thick burried directly in ground (earth pit not less 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below ground level connected to thick electrode and 32x6 mm GI strip as earthing by means of nuts bolts check nuts and washers made of galvanised iron or steel earth strip protected by galvanised iron pipe 40 mm bore (medium grade) and connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1 precast RCC cover slab 54 x 54 cm x 5 cm with reinforcement with 8 mm TMT bars @ 150 C/C with one handle and funnel for watering charcoal or coke and salt in alternate layers & necessary earth work in soft/loose soil complete all as shwon in electrical plate No 5 of SSR Part-I including testing on completion all as specified and directed.

S S CONSTRUCTION CO