Campus Development,Road Work and Furnishing work at Collectorate Building,Dhanbad.

Amount

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand(zone-III) : 3 graded stone aggregate 20mm nominal size). Foundations, footings, bases of columns, etc. for mass concrete

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Extra for providing and fixing wind ties of 40x 6 mm flat iron section.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab upto 0.50 sqm

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Maintenance of Kitchen garden including preparation of beds manuring/ fertigation weeding hoeing watering planting of vegitable seeds including spraying of insecticide and pesticide and Harvesting. (Note:-Only Good Earth, Manure, Fertilizer, Insecticide & Pesticide will be provided by the Department and other T & P material/articles shall be provided by the contractor) and as per direction of officer in charge

Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department and other T & P material/articles shall be provided by the contractor) and as per direction of officer in charge.

Providing and Displaying Bismarckia Palm 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Cycus cirsnallis well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Fishtail palm well developed with fresh & healthy foliage leaves of ht 210 to 240cm Specimen in 35 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Foxtail palm well developed with fresh & healthy foliage of ht. 210 to 240 cm in big 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2 x 1.5 sq. mm

S/F rewireable double pole/TP&N switch disconnector - Providing and fixing following capacity double pole/TP&N sheet metal switch disconnector fuse unit in existing metal board with rewireable type fuses, including drilling holes in metal board, making connections, etc as required. 32 amps, double pole

80mm dia Earthing Electrode 2mtr. Length / 80mm dia Earthing Electrode 3mtr. Length / 50mm dia Earthing Electrode 2mtr. Length/50mm dia Earthing Electrode 3mtr. Length & Backfill Compound chemical 4 Bag(per bag 25 KG)

Salt/Charcoal for plate earth electrode - Extra for using salt and charcoal for G.I. or copper plate earth electrode as required.

S/L L.T power XLPE insulated PVC sheated (heavy duty) aluminium conductor armoured electric cable for working voltage 1100 volts IS:1554(Part I)1989 Make - havells/polycab/finolex/ or equivalent) 10 sq. mm , 2 Core

MV cable laying upto 25 sq.mm. in ground - Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trecnch aetc. as required.

10sq.mm. aluminium lugs

S.I.T.C of following rating LED Post top lamp made in die cast aluminium housing with decorative clear/opal serylic diffuser on existing pipe including connection with 1.5sq.mm. copper conductor etc all complete as required.20/25W LED Post top lamp clear

50 mm dia, medium class GI pipes (for garden light fitting including painting etc as required.) Pge 35 (vi) 65 mm dia

Including Royalty @24 per cum cost of watering rolling & compaction cum

Granular Sub-Base with Graded Material (Table:- 400-1) Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401.

Wet Mix Macadam (Plant Mix Method) Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Prime Coat over WMM/WBM Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means.

Tack Coat on Granular surfaces treated with primer Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

Bituminous Macadam Grading-II with VG-30 Grade Packed Bitumen Providing and laying bituminous macadam with higher capacity hot mix plant using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction.

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom.

Bituminous concrete Grading- II with VG-30 Grade Packed Bitumen Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @5.4 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment , rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause no. 507 complete in all respects.

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)

Solar Powered Road Marker (Solar Stud) Supplying of Solar Raised Pavement Markers made of polycarbonate molded body with circular shape, solar powered, LED self illumination in active mode 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode.The marker shall support a load of 20000 kg tested in accordance to ASTM D 4280.The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0 C to 70 C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency of blinkikng in 1 Hz.There should be current losses of less than 20 microamperes at 2.4 V in sleepcharging mode to enhace the life of the marker and a full charge should provide for a minimum autonomy of 50 hours.The height, width and length of the marker shall not be less than 10mmx100mmx100 mm. Also, the surface diameter of the marker shall not be less than 100 mm respectively.The weight of the marker shall not exceed 0.5 Kilograms.Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive and complete as directed by the engineer.)

Retro-Reflectorised Traffic Signs Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class-B Type IV retro reflective sheeting fixed cover 2 mm thick aluminium sheeting vide clause 801.3, 3mm/4mm thick aluminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67.80 cm x 60 cm rectangular

Direction and Place Identification Signs with size more than 0.9 sqm size Board.(Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminium composite material sheet with overall thickness of 4 mm with area exceeding 0.9 sqm fixed over back support frame of min 40 x 40 x 5 mm Angle mounted on two nos. of mild steel circular pipe 65 NB, 3.2mm thickness and 4.5m meter total height firmly fixed to the ground by means of properly designed foundation with M 25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)

Cast in Situ Cement Concrete M 20 Kerb with Channel (Construction of cement concrete kerb with channel with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M15 grade foundation 150 mm thick, kerb channel 300 mm wide, 50 mm thick in PCCM20 grade, sloped towards the kerb, kerb stone with channel laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 409)

Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : - Dark shade pigment using ordinary cement

CARRAIGE OF MATERIALS

Brick

Chips

Metal

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above14HP modules, microprocessor based Controller, top discharge type condensing unit(s),with R410A Refrigerant, vibration isolators, with suitable foundation etc.complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V+/-10%, 3Phase,50HzAC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5

VRV/VRF INDOOR UNITS:

INDOOR UNIT-CASSETTE TYPE

Supply,installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower,multi speedmotor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill,necessary supports, vibration isolation,cordless remote control etc., suitable for operation on single phase 230V±10%,50Hz AC supply, complete, asrequired. The unit shall have automatic force shut down provision incase of fire on receiving signal from BMS System.The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and19 Degree C WB temperature.

REFRIGERANT PIPING:

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation / with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thicknessas given below for Suction and Liquid lines, all accessories as per specifications etc. as required :

6.4mm dia (OD) (Soft drawn) with tube thickness1.2mm with19mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness1.2mm with19mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness1.2mm with19mm thick insulation

15.9 mm dia (OD) (Soft drawn) with tube thickness1.2mm with19mm thick insulation

19.1 mm dia (OD) (Soft drawn) with tube thickness1.2mm with19mm thick insulation

22.2 mm dia (OD) (Soft drawn) with tube thickness1.2mm with19mm thick insulation

28.6 mm dia (OD) (Soft drawn) with tube thickness1.2mm with19mm thick insulation

34.9 mm dia (OD) (Soft drawn) with tube thickness1.62mm with19mm thick insulation

Supply and erection of hot dip G.I. cable tray perforation not more than 17.5% for specific dimensions along with tees, bends. The cable tray shall be hang from ceiling/ fixed to wall with necessary angle/flat iron / hanging rod, for ceiling suspensions, clamps, anchor fastner, nuts, bolts, washers, not mor than 1.5 mtr. apart complete as per specification to complete the job. The tray shall be as follows :-

150 x 50 mm x 1.6mm thick

200 x 50 mm x 1.6mm thick

300 x 50 mm x 1.6mm thick

450 x 50 mm x 1.6mm thick

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

25 mm dia. ISI marked, steel conduit

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

25 mm dia. ISI marked, PVC conduit

WIRING IN EXISTING CONDUIT / PVC CASING CAPPING WITH COPPER CONDUCTOR

Supply,& drawing following sizes of FRLS PVC insulated copper conductor ,single core cable in the exixsting surface/reccessed steel/pvc conduit as required.

2x 1.5Sq mm

4x 2.5sq.mm

EARTHING SYSTEM

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing aling with existing surface/recessed conduit/submain wiring/cable as required.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6mm reveal profile (white/black), comprising of main-T runners of size 15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including

Supplying, fixing and commissioning of fountain near the entrance with UPVC pipelines, complete pumping & recirculation system of approx 13.5 lps discharge at 20m head including control panels & bypass arrangement.Fountain to have 8 No's brass nozzles of flow 45 lpm having height of throw 1500 mm and 20 No's goam jet nozzles 60 lpm having height of throw 300 mm.

It should have provision of underwater LED lights (warm white colour) 20 No's 12V 12W DC IP 68 and 8 No's 12V 20W DC IP68 complete with conduits, drivers, transformer, wiring and all accessories.

S/F suitable sizes PVC sintex box with cable connector and 6 amp MCB including locking arrengement connection etc as required .

Y-JOINTS:

Supply Installation, testing, commissioning of supply & return Y-joints sets of required size for refrigerant piping as per manufacturer standards.

Y- Joints set

DRAIN PIPING :

Providing and fixing of PVC drain pipe of 6 Kg /cm2 pressure rating complete with 6mm thick closed cell nitrile rubber insulation, fittings, supports, valves as per specifications & drawings.

25 mm dia

32 mm dia

VRV/VRF ELECTRICAL WORK

Design, fabrication, supply, installation, testing and commissioning of LT Panel / Sub-distribution panels fabricated out of 2mm thick for structural members and 1.6mm thick for door and covers CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system and lifting hooks shall also be provided in case of large panels. Degree of ingress protection of IP-54.

ODU Panel at Terrace (left Side)

Incomer (1 No.):

250A, 4 pole MCCB (25 KA)

Metering:

0-500 Volts, digital Voltmeter and shall be protected by 2Amps MCBs.

Bus Bars:

320Amps TP Aluminium busbars, colour coded with heat shrinkable insulation sleeves

OutGoings

(3.0) Nos. 4 pole 100A MCCB

(1.0) Nos. 4 pole 63A MCCB

(1) Nos. 32A MCB spare

ODU Panel at Terrace (Right Side)

Incomer (1 No.):

200A, 4 pole MCCB (25 KA)

Metering:

0-500 Volts, digital Voltmeter and shall be protected by 2Amps MCBs.

Bus Bars:

250Amps TP Aluminium busbars, colour coded with heat shrinkable insulation sleeves

OutGoings

(3) Nos. 4 pole 63 MCCB

(1) Nos. 32A MCB Spare

CABLES

Supplying & laying of following 1100 volt grade XLPE insulated PVC sheathed copper conductor armoured cables including, anchor fastners on wall with suitable clamps, saddles fixing bolts connecting testing and commissioning etc as per specification complete as required.

4.0 core 10 Sq mm

4.0 core 16 Sq mm

Smart Mid Back Chair:- SEAT : The seat is made up of 12mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. Seat Size 510mm (W) X 535mm (D). The seat tested for 1,00,000 cycles to be completed with a load of 57kg impact force on the seat as per ANSI / BIFMA X5.1.Seat foam made out of moulded Polyurethane foam with Density: 50-60 Kg/m3, Hardness: 15-20Kgf and Tensile strength: 0.9-1.2 Kg/cm2.Medium Back (MB) 670mm (H) X 535mm (W). The backrest tested for 1,20,000 cycles to be completed with a load of 44.5Kg as per ANSI / BIFMA X5.1. Fixed Armrest : The armrests made up of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S. insert. MECHANISM : SINGLE POINT SYNCHRO MECHANISM : Conventional mechanism with one lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 3°~10°. and back tilting angle is 87°~106°. Also it has the back tension adjustment knob. Mechanism tested for 3, 00,000 Cycles as per ANSI / BIFMA X5.1. GAS LIFT :Gas lift pipe diameter 50mm and has an Height adjustment stoke of 112mm. Gas lift tested for 1, 00,000 Cycles as per ANSI / BIFMA X5.1. Meets DIN 4550 Class 3 and all applicable ANSI/BIFMA, EN performance standard Nylon base with Castors : The base made up of injection moulded in black glass filled nylon and fitted with 5Nos twin wheel castors. The base is 658mm pitch circle diameter. The base tested for static load of 1134Kg as per ANSI / BIFMA X 5.1.

Wooden Storage wudsafe 900 X 450 x 1200 (WDH)mm Size 900 mm wide x 425 mm depth x 1200 mm height : Top Panel: Option of 25 / 18 mm thick Prelaminated Particle Board with PVC Edge Banding.Door Shutters: 18 mm thick Prelaminated Particle Board with PVC Edge Banding.Side Panels: 18 mm thick Prelaminated Particle Board with PVC Edge Banding.Back Panels: 9 mm thick Prelaminated Particle Board with PVC Edge Banding.Shelf Panels: 18 mm thick Prelaminated Particle Board with PVC Edge Banding.Hardware: High Quality Components for fitting the panels, handles and lock.Lock: Premium Lock with Wave Key Technology.Provision for adjustability of the Shelf Panel inside the Storage with Pin Support.PVC Edge Banding is done by machine pressed with hot melt glue.

Smart visitor model Back Rest :. Back rest size 615 mm x 450 mm , seat Seat is made of 12 mm thick (7 layers ) hot pressed plywood and moulded seat and foam upholestered with fabric , seat size 455 mm x 480 mm and 470-480 mm height . Seat foam Density 50-60 Kg/m3 , Hardness 15-20 kgf , compression set- 50% 10 Max , Tensile strength 0.9-1.2 kg/cm square , Tear strength (Min) 2.2 N/cm , Resilence 50%-60%. Fixed ARM rest . Understructure metal powder coated with min 19 mm dia pipe leg and 2 mm thick (ERW Pipe-IS 1161 -1998)

22 seater Grupthink Conference table Table Tops – Available in standard modules, made of 25mm thick MDF with waterfall top edges finished in PVC Membrane using unique wrap around technology for better aesthetics & long lasting use. Understructure – Legs made of 25mm thick standard Black matt colour post formed panels interconnected with 18mm thick standard Black matt colour pre-laminated modesty panels, with height adjustable levelers to take care of uneven floors. Wire Management – Concealed wire management to take care of basic wiring requirements both horizontally & vertically. For closed configurations, liftable top cover, made of 12mm MDF finished in PVC Membrane, is provided to access the horizontal wire carrier. For open configurations, wire channel is mounted on the inner side of modesty panel for horizontal wire carrying. Vertical wire management is through flexible vertical wire manager. Standard table top height – 740mm. Designed for Flexibility through modular Construction, PVC Membrane Finish Tops for seamless surface, Post formed Legs for safe use, Provision for easy wire management, Upgradeable / reconfigurable for future needs.

Executive Table, Presidency 7 feet Main table :2100 (W) X 900(D) x 740(H)with side unit in size of 1200 (W) X 500(D) x 740(H) + 1nos Back unit in size of 1800 (W) X 450(D) x 740(WDH)mm Table Top: - The table top is Post-laminated for better abrasion and scratch resistance. The Table top is made of Particle Board with 1mm top laminate and 1mm bottom laminate. The complete Table top is 36mm thick. All exposed edges have 2mm PVC edge banding. The modesty is Post-laminated for better abrasion and scratch resistance. The Modesty is made of 18mm Particle Board with 1mm top laminate and 1mm bottom laminate. All exposed edges have 2mm PVC edge banding. The colour of the modesty is matching to the table top colour. The understructure is 200mm wide on one side is 25mm. It is made up of prelam particle board and is black in colour. The understructure has wire management properties and can carry concealed wires within it. All exposed edges have 2mm PVC edge banding. The extesnion table in size of 1150 (L) x 750 (W) x 740 is of an arc shape and Post-laminated for better abrasion and scratch resistance. The Table top is made of Particle Board with 1mm top laminate and 1mm bottom laminate. All exposed edges have 2mm PVC edge banding. The complete Table top is 36mm thick and available in black colour. The back storage has 2 sections; namely; storage unit and display unit (above the storage space). The storage caracass is made of 18mm thick prelam particle board of black colour. The shutters and storage top are Post-laminated for better abrasion and scratch resistance. The storage top is made of 36mm Particle Board with 1mm top laminate and 1mm bottom laminate. The shutters are made of 18mm Particle Board with 1mm top laminate and 1mm bottom laminate. The storage back is made of 9mm thick prelam particle board. The shutter and storage top colour is matching to the main table. The storage is completely handle less and is openable from the top. Al hinges are from Hettich. One number EBCO premium lock has been considered for the storage. All exposed edges have 2mm PVC edge banding.

Alivio High Back Chair :-VOC Certified chair - ANSI/BIFMA X7.1-2007 & ANSI/BIFMA M7.1-2011.The cushioned seat assembly shall consists of moulded polyurethane foam upholstered with fabric. The foam is assembled over a 12mm thick hot pressed plywood . The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. Size of back shall be (W)-48.5cm, (H)-49.5 cm & size of seat shall be (W)-49 cm x (D)-44.0 cm .Armrest has 2 way button operated height adjustment and depth adjustment. The arm top is made of soft moulded PU with MS insert.The mechanism of chair shall have following features:360 degree revolving type, Synchro mechanism, Tilt tension adjustment, multi position tilt limiter with Back-safety return feature. Head rest assembly shall made up of polyurethane foam upholstered with fabric. The head rest assembly is mounted on the top of back. It has 5 point adjustment of upto 8 cm . The chair shall be provided with pneumatic height adjustment which shall have stroke of 112 mm. The pedestal shall be made of die-cast polished Aluminium . it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 1 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon or PU . Overall dimensions of Chair shall be, Width of Chair - 70 cm, Depth of Chair - 70.0 cm as measured from pedestal below. Height from ground - min 96.5 to max 108.0 cm. Seat height - min 47 cm to max 58.5 cm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA x5.1 standards

Alivio Mid Back Chair :-VOC Certified chair - ANSI/BIFMA X7.1-2007 & ANSI/BIFMA M7.1-2011.The cushioned seat assembly shall consists of moulded polyurethane foam upholstered with fabric. The foam is assembled over a 12mm thick hot pressed plywood . The back shall made up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. Size of back shall be (W)-48.5cm, (H)-49.5 cm & size of seat shall be (W)-49 cm x (D)-44.0 cm .Armrest has 2 way button operated height adjustment and depth adjustment. The arm top is made of soft moulded PU with MS insert.The mechanism of chair shall have following features:360 degree revolving type, Synchro mechanism, Tilt tension adjustment, multi position tilt limiter with Back-safety return feature. Head rest assembly shall made up of polyurethane foam upholstered with fabric. The head rest assembly is mounted on the top of back. It has 5 point adjustment of upto 8 cm . The chair shall be provided with pneumatic height adjustment which shall have stroke of 112 mm. The pedestal shall be made of die-cast polished nylon. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 1 cm pitch-centre-dia (70.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon or PU . Overall dimensions of Chair shall be, Width of Chair - 70 cm, Depth of Chair - 70.0 cm as measured from pedestal below. Height from ground - min 96.5 to max 108.0 cm. Seat height - min 47 cm to max 58.5 cm. Dimensions tolerance / variations shall be within +/- 1 cm. Chair tested as per ANSI/BIFMA x5.1 standards

3 Seater Alysia Sofa:- In Size 2065 X 850 X 760(WDH)mm , Frame : Plywood and klin chemical treated tropical meranti wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Leatherette and Malamine finish rubber wood legs.

2 Seater Alysia Sofa: In Size 1525 X 850 X 760(WDH)mm , Frame : Plywood and klin chemical treated tropical meranti wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Leatherette and Malamine finish rubber wood legs.

Centre Table:- Size 1200 mm wide x 600 mm depth x 450 mm height.Center Table with 8mm thick Clear Glass top, Under-structure verticals are made up of 50mm thick MDF with 0.4mm thk European PVC foil & Horizontal support from 50mm thick Prelaminated MDF.All sides to have 0.8mm thk edge band.

Corner Table:- Size 450 mm wide x 450 mm depth x 450 mm height.Center Table with 8mm thick Clear Glass top, Under-structure verticals are made up of 50mm thick MDF with 0.4mm thk European PVC foil & Horizontal support from 50mm thick Prelaminated MDF.All sides to have 0.8mm thk edge band.

32 seater Grupthink Conference Room table as per Layout Table Tops – Available in standard modules, made of 25mm thick MDF with waterfall top edges finished in PVC Membrane using unique wrap around technology for better aesthetics & long lasting use. Understructure – Legs made of 25mm thick standard Black matt colour post formed panels interconnected with 18mm thick standard Black matt colour pre-laminated modesty panels, with height adjustable levelers to take care of uneven floors. Wire Management – Concealed wire management to take care of basic wiring requirements both horizontally & vertically. For closed configurations, liftable top cover, made of 12mm MDF finished in PVC Membrane, is provided to access the horizontal wire carrier. For open configurations, wire channel is mounted on the inner side of modesty panel for horizontal wire carrying. Vertical wire management is through flexible vertical wire manager. Standard table top height – 740mm. Designed for Flexibility through modular Construction, PVC Membrane Finish Tops for seamless surface, Post formed Legs for safe use, Provision for easy wire management, Upgradeable / reconfigurable for future needs.

Executive Table in size of 2550 x 900 x 740 are made of 48mm Thick MDF with venner Finish which is joined by combining 2 tale tops. The table tops have a dual tone with the lower top being in matt black colour.The Table top has chamfered edge adding to the aesthetics and the drip-proof profile. No polishing is done thereby ensuring low VOC (Volatile Organic Compounds). The overall thickness of the Table top from visible side 48mm. Table top and Gable End: 48 mm thick MDF with Veener finish with 3D-thermoformable furniture film, calandered PVC uni colored, top coated with lacquer Backside with adhesion promoting primer. Modesty: 18 mm thick MDF with Veneer finish with 3D-thermoformable furniture film, calandered PVC uni colored, top coated with lacquer Backside with adhesion promoting primer..The understructure has wire management properties and can carry concealed wires within it.

Executive High Back Define Chair in Leather Made up of combination of 12mm (7 layers) & 4mm (3 layers) thick hot pressed plywood and 37mm thick, 32 Density U foam upholstered with fabric or Leather. The back ply and foam is designed with contoured lumber support for achieving comfortable seating posture. Back rest available in two sizes - High Back 860mm (H) X 550mm (W). The backrest tested for 1,20,000 cycles to be completed with a load of 44.5Kg as per ANSI / BIFMA X5.1. SEAT : The seat is made up of 12mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. Seat Size 510mm (W) X490mm (D). The seat tested for 1,00,000 cycles to be completed with a load of 57kg impact force on the seat as per ANSI / BIFMA X5.1.,Seat foam made out of moulded Polyurethane foam with Density: 50-60 Kg/m3 and Resilience: 50% - 60% ARM REST : The armrests made of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S. insert. Arm pad size 248mm (L) x 92mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 6mm thick. HR steel. 2D arms with height adjustable up to 80mm & front and back with adjustable up to 60mm. Arm rest tested for 60,000 Cycles to be completed with load of 40Kg as per ANSI / BIFMA X5.1. MECHANISM : FOUR POINT SYNCHRO MECHANISM : Mechanism with two lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 0°~6°. and back tilting angle is 89°~109°. Also it has the back tension adjustment knob. Mechanism tested for 3, 00,000 Cycles as per ANSI / BIFMA X5.1. GAS LIFT :Gas lift pipe diameter 50mm and has an Height adjustment stoke of 120mm. Gas lift tested for 1, 00,000 Cycles as per ANSI / BIFMA X5.1. Meets DIN 4550 Class 3 and all applicable ANSI/BIFMA, EN performance standard BASE :ALUMINIUM BASE : The base made up of pressure die casted in aluminium fitted with 5Nos twin wheel castors. The base is 650mm pitch circle diameter. The base tested for static load of 1134Kg as per ANSI / BIFMA X 5.1. CASTERS : NYLON CASTORS : The twin wheel castors are injection moulded in nylon and diameter of Castor 50 mm. The castors are tested for 1,00,000 Cycles as per ANSI / BIFMA X 5.1.

Visitor Define Chair in Fabric Made up of combination of 12mm (7 layers) & 4mm (3 layers) thick hot pressed plywood and 37mm thick, 32 Density U foam upholstered with fabric . The back ply and foam is designed with contoured lumber support for achieving comfortable seating posture. Back rest available in two sizes - Mid Back (MB) 700mm (H) X 550mm (W). The backrest tested for 1,20,000 cycles to be completed with a load of 44.5Kg as per ANSI / BIFMA X5.1. SEAT : The seat is made up of 12mm thick (7 layers) hot pressed plywood and moulded seat foam upholstered with fabric. Seat Size 510mm (W) X490mm (D). The seat tested for 1,00,000 cycles to be completed with a load of 57kg impact force on the seat as per ANSI / BIFMA X5.1.,Seat foam made out of moulded Polyurethane foam with Density: 50-60 Kg/m3 and Resilience: 50% - 60% ARM REST : The armrests made of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S. insert. Arm pad size 248mm (L) x 92mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 6mm thick. HR steel. 2D arms with height adjustable up to 80mm & front and back with adjustable up to 60mm. Arm rest tested for 60,000 Cycles to be completed with load of 40Kg as per ANSI / BIFMA X5.1. MECHANISM : FOUR POINT SYNCHRO MECHANISM : Mechanism with two lever control for lock and seat height adjustment. Mechanism made out of MS Plate thickness is 3mm and seat is tilting angle is 0°~6°. and back tilting angle is 89°~109°. Also it has the back tension adjustment knob. Mechanism tested for 3, 00,000 Cycles as per ANSI / BIFMA X5.1. GAS LIFT :Gas lift pipe diameter 50mm and has an Height adjustment stoke of 120mm. Gas lift tested for 1, 00,000 Cycles as per ANSI / BIFMA X5.1. Meets DIN 4550 Class 3 and all applicable ANSI/BIFMA, EN performance standard BASE :ALUMINIUM BASE : The base made up of pressure die casted in aluminium fitted with 5Nos twin wheel castors. The base is 650mm pitch circle diameter. The base tested for static load of 1134Kg as per ANSI / BIFMA X 5.1. CASTORS : NYLON CASTORS : The twin wheel castors are injection moulded in nylon and diameter of Castor 50 mm. The castors are tested for 1,00,000 Cycles as per ANSI / BIFMA X 5.1.

X-Desk Main table of size 1500 x 750 x 740 (WDH)mm side table of size 1050x525x740 (WDH)mm and 3 Drawer pedestal 350x450x550mmH, Table Top made of 25mm thick prelam particle board confirming to IS 12823 Interior Grade with the exposed edges sealed with 2mm PVC edge banding. The height of the table top from the ground should be 740mm. supported on the legs and beams. Legs are made of 50 x 50mm thick Square pipe made of 1.6mm thick CRCA pipe duly powder coated interconnected with tie member of 80 x 40mm pipe structure made of 1.6mm thick CRCA duly powder coated. Back Storage top Panel: Option of 25 mm thick Prelaminated Particle Board with PVC Edge Banding.Door Shutters: 18 mm thick Prelaminated Particle Board with PVC Edge Banding.Side Panels: 18 mm thick Prelaminated Particle Board with PVC Edge Banding.Back Panels: 9 mm thick Prelaminated Particle Board with PVC Edge Banding.Shelf Panels: 18 mm thick Prelaminated Particle Board with PVC Edge Banding.Hardware: High Quality Components for fitting the panels, handles and lock.Lock: Premium Lock with Wave Key Technology.Provision for adjustability of the Shelf Panel inside the Storage with Pin Support.PVC Edge Banding is done by machine pressed with hot melt glue

Perfo 3 seater bench- Seat , arms & legs : High quality cold-rolled steel is perforated, pressed and welded to form the shape. Thickness is 1.2mm. Centre beam : High quality cold-rolled steel is pressed and welded to form the shape. The surface is treated to avoid rust . Thickness is 2mm. Sizes are 1765 x 710 x 765 (WDH)

Dias Table as per Design & Drawing

Library Rack model Search :- Back to Back Sided Rack in Size of 1000LX700DX1860H The side, top and back panels are made of 18mm thick prelam particle board with lamination on both sides. The prelam particle board is mounted on the basic frame structure made out of 2" X 1" thick CRCA pipe. The shelves are made up of 25mm thick Prelam Particle board with same lamination on both sides. The top corners are covered with aesthetically extruded aluminium giving a complete smooth finish to the structure. The bottom three shelves of each unit are at various angles to enable quick location of books / references. The bottom most shelf is inclined at 15 degree, the 2nd lst shelf is inclined at an angle of 9 degree and the 3rd last shelf are inclined at an angle of 3 degree. The shelves are suitable for books of different heights. The lower 2 shelves are of 280mm height suitable for larger size books. The bottom 3 shelves are fixed and the top 3 shelves are height adjustable to accommodate books of various sizes. Each module can be provided with A5 size acrylic signage board on the side for defining categories. The racks too can be provided with individual rack signage for easier sub category identification. The search is available in both single sided and double sided configuration with main and add on modules. The complete system is extremely sturdy and is equipped with 6levellers to take care of any floor unevenness. The immaculate detailing, well finished end caps and outer frame of the rack in matching powdercoated finish adds to the overall aesthetics.

Supply & installation of wall paneling of Anutone / Tranquil / Mechtrix Nishabdm slats surco high density fiberboard made out of pure pinewood particles with green building certified , Fire Resistance - Pink in colour core with 5 test Fire Resistance BS 476 part 5 , BS 476 part 6 , BS 476 part 7 ISO 1182 ASTM E662 Smoke Density - Melamine laminated finish, perforated wooden grooved HDF slats L16-2 (2 mm grooves @ 8 mm centers),tongue-groove edge for a seamless look of lineal dimension size 128 mm x 2440 mm x 16 mm thick having density 700 Kg /m3, weight -9 Kgs/m2 with back fleecs from soundtex Germany nonwoven acoustic to be pasted on slats surco is to be installed by using GI strut system. The technical parameters are as follows Core Variants - Fiberboard, Climate (OC RH) – 50, 70 Light reflectance – 75%,Green (RC %) – 25, Hygiene (VoC, Clean room) – Low, Class 1,Strength, Load capacity (Kg) - Anti sag, Ball-Impact. The concealed wall paneling system shall include GI Wall channel (WC25) having thickness 0.45mm, length 3600mm, unequal flanges of 15 & 20mm and web of 25mm should be fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm centers. Then fixed Main channels (MC45) having thickness 0.9mm, length 3600mm, equal flanges of 15mm and web 45mm from the side wall & fixed at every 1200mm centers with GI cross channel(CC25) having thickness 0.45mm, length 3600mm, knurled web 35mm, depth of 25mm and equal flanges 9.5mm is fastened to the Main channel in the direction perpendicular to the Main Channel at every 600mm centers. The framework will maintain 50 / 75 mm gap from the walls. Now clad the wooden slats surco on the CC 18 with the help of center & edge clips to get better locking of slats. The tongue & groove are to be properly aligned to get flush look . Synth poly fiber PF 5 x 50 wool of 500 gsm to be filled between the horizontal & vertical studs as in filler with the help of wire / stick 7 adhesive. Test certificate of the use products shall be submitted after procurement of materials Make Anutone, Ecotone

Add 18% GST

Add 1% Labour cess 1%

UTSAV UDYOG