Construction of RAC Bunglow (E1-Type) (01-Unit) at Lunawada Dist. Mahisagar

No. Figure Amount

1 Excavation for foundation upto 1.50 mt depth including sorting out and 186.00 Cum 278.06

stacking of useful materials and disposing the excavated stuff within all lead

and lift for soft rock not requiring blasting.

2 Excavation for foundation from 1.50 mt to 3.00 mt. depth including sorting out 86.70 Cum 651.26

and stacking of useful materials and disposing the excavated stuff within all

lead and lift (E) Hard rock.

3 Filling in foundation and plinth with sand in layers of 20 cm thickness including 39.40 Cum 479.80

watering, ramming and consolidating etc. complete.

thickness including watering, ramming and consolidation etc. complete.

5 Anti Termite System : P/L of Permanent piping technology Anti Termite 196.90 Sq.m. 63.63

treatment before flooring work by installing LLDP (Low linear density

Polyethylene) tube of 8 mm O.D.& 6.4 mm I.D. with in Built Pressure

Compensation chip every 30 cm interval in the tube, having working pressure

of 2 kg/cm 2 and release rate of 1.9 ltr/Hour fixed by P-Clip and nails. The

LLDP pipe shall be installed at the entire periphery of the building and at

internal network of building depth of 20 to 200 mm under floor every 2 to

mtr. c/c distance (adjustable as per building layout) & ends of loop pass

through a PVC Elbow of minimum 32 mm ID at junction box of wall and floor

level, entering into a steel reinforced grooved flexible pipe mini. 22 mm LD

leading into junction box and during injecting chemicals for termite control

treatment.

The anti-termite chemical Lmidcloprid 30.5% SC mix as per IS 6313 (part-III)

shall be injected by the pressure pump diluted with water @ 10.5 ml/5ltr of

water at the rate of 2 kg/sq.cm. @ 5 ltr /Smt. the contractor shall submit

approved line plan for piping system and junction boxes dully approved by

Engineer-in-charge with bond of 5 years warranty. (II) Anti Termite chemical

injected area (Chemical injecting including labour cost)

6 Providing and laying controlled cement concrete M-150 and curing complete 13.00 Cum 4022.72

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Foundations and plinth for PCC.

7 Providing and laying controlled cement concrete M-250 and curing complete 42.70 Cum 4734.10

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Foundations, footings & mass concrete.

8 Providing and laying controlled cement concrete M-250 and curing complete 6.60 Cum 8111.09

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns upto plinth level.

9 Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 33.00 Cum 3092.22

machine cut stone aggregate 40 mm nominal size) and curing complete

including cost of form work in foundation and plinth.

10 Providing and laying controlled cement concrete M-200 and curing complete 15.90 Cum 8095.62

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns for Ground floor.

11 Providing and laying controlled cement concrete M-200 and curing complete 13.40 Cum 8137.17

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns for First floor.

12 Providing and laying controlled cement concrete M-200 and curing complete 2.40 Cum 8178.71

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Columns for Terrace floor.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

13 Providing and laying controlled cement concrete M-250 and curing complete 20.10 Cum 6398.17

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Ground beam and plinth beam.

14 Providing and laying controlled cement concrete M-150 and curing complete 29.60 Cum 4662.62

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Plinth Slab.

15 Providing and laying controlled cement concrete M-200 and curing complete 17.60 Cum 6364.82

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Beam for Ground floor.

16 Providing and laying controlled cement concrete M-200 and curing complete 5.50 Cum 6406.36

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Beam for First floor.

17 Providing and laying controlled cement concrete M-200 and curing complete 1.60 Cum 6934.10

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Chhajja for Ground floor.

18 Providing and laying controlled cement concrete M-200 and curing complete 0.80 Cum 6975.65

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Chhajja for First floor.

19 Providing and laying controlled cement concrete M-200 and curing complete 1.20 Cum 9021.71

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Lintel for Ground floor.

20 Providing and laying controlled cement concrete M-200 and curing complete 0.60 Cum 9063.26

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Lintel for First floor.

21 Providing and laying controlled cement concrete M-200 and curing complete 29.00 Cum 6776.77

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Ground floor slab.

22 Providing and laying controlled cement concrete M-200 and curing complete 10.20 Cum 6818.31

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in First floor slab.

23 Providing and laying controlled cement concrete M-200 and curing complete 2.50 Cum 8157.88

including the cost of form work but excluding cost of reinforcement for

reinforced concrete work in Staircase for Ground Floor to first floor

24 Providing and fixing 90 cm high Stainless steel railing made from anti 26.00 Rmt. 2936.07

corrosive 304 grade S.S. pipe of 50 mm dia. (16 gauge) as hand rail with S.S.

304 grade baluster / posts of square pipe 32mm x 32mm (16 Gauge) as a

vertical support fixed in RCC slab at 1.2m c/c including three horizontal S.S.

pipes of 16mm dia. (16 gauge) at equal distance fixed by 18.75mm dia (16

Gauge) S.S. pipe with baluster and round stainless steel railing ball of 25mm

dia. including accessories as per detailed drawing as directed etc. complete.

25 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement with fusion bonded 19202.50 Kg. 77.29

epoxy coating not less than 175 micron thickness and upto 300 micron to

reinforcement bars as per IS-13620-1993/ASTM-775M (including testing of

coating at plant and all taxes) for R.C.C. work including bending, binding and

placing in position complete upto floor two level for Ground floor.

26 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement with fusion bonded 4504.00 Kg. 78.34

epoxy coating not less than 175 micron thickness and upto 300 micron to

reinforcement bars as per IS-13620-1993/ASTM-775M (including testing of

coating at plant and all taxes) for R.C.C. work including bending, binding and

placing in position complete upto floor two level for First floor level.

27 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement with fusion bonded 660.00 Kg. 79.39

epoxy coating not less than 175 micron thickness and upto 300 micron to

reinforcement bars as per IS-13620-1993/ASTM-775M (including testing of

coating at plant and all taxes) for R.C.C. work including bending, binding and

placing in position complete upto floor two level for Second floor level.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

28 Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles 99.40 Sq.m. 1674.15

having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for

extra strength. The Light weight calcium silicate ceiling tiles shall have, light

reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity

resistance and also having thermal conductivity 0.043° w/m KC. for the best

thermal Insulation. The Light weight calcium Silicate tile shall be of approved

texture Fine fissured/ Spintone/ Cosmos having NRC value of 0.5 & Globe

having NRC value of 0.75 NRC or equivalent of size 595 x 595 mm to be laid

on true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including both

side) consisting of main ‘T’ runner suitably spaced at joints to get required

length and size of 24 x 38mm made from 0.30 mm thick (minimum) sheet,

1200mm centre to centre and cross ‘T’ of size 24 x 28mm made out of

0.33mm (Minimum) sheet spaced 1200mm along spaced between main 'T' at

600mm centre to centre to form a grid of 1200 x 600mm and size 24 x 48mm

made of 0.30mm thick (Minimum) sheet to be interlocked at middle of the

1200 x 600mm panel to form grid of size 600 x 600mm resting on periphery

walls/partitions on a perimeter wall angle pre-coated steel of size (24 x 24 x

3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at

450mm centre to centre with 25mm long dry wall screws @ 230mm interval

and laying 15mm thick densified edges light weight calcium silicate ceiling

tiles of approved texture (Fine fissured / Cosmos / Spintone) in the grid

including cutting / making opening for services like diffusers, grills, light

fittings, fixtures, smoke detectors etc., whenever required, Main 'T' runners to

be suspended from ceiling using G.I. slotted cleats of size 25 x 35 x 1.6mm

fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.I.

adjustable rods with galvanized steel level clips of size 85 x 30 x 0.8mm,

spaced at 1200mm center to centre long main 'T' bottom exposed with 24mm

of all T-sections and also provide additional frame work and

suspended G.I. support as required height shall be pre-painted with polyester

baked paint, for all heights, as per specifications, drawings and as directed by

engineer-in-charge. Note:- Only calcium silicate false ceiling area will be

measured from wall to wall. No deducation shall be made for exposed

frames/opening (cut outs) having area less than 0.30sqm. The calcium silicate

ceiling tiles shall fissured / Spintone / Cosmos and 0.75 NRC for Globe, light

reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity

resistance and also having thermal conductivity. 0.043 w/m KC for the best

thermal Insulation.

29 Providing and laying brick work using common burnt clay building 15.50 Cum 4214.33

conventional type bricks having crushing strength not less than 35 Kg./Sq.cm.

in foundation and plinth in cement mortar 1:6 (1 cement : 6 fine sand)

including the cost of all materials and labour charges etc. complete.

30 Providing and laying brick work using common burnt clay building 64.30 Cum 4496.05

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for Ground Floor including the cost of all materials

and labour charges etc. complete.

31 Providing and laying brick work using common burnt clay building 46.00 Cum 4538.16

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for First Floor including the cost of all materials and

labour charges etc. complete.

32 Providing and laying brick work using common burnt clay building 10.70 Cum 4580.28

conventional type bricks having crushing strength not less than 35 Kg/sq.cm.

in super structure above plinth level upto floor two level in cement mortar 1:6

(1 cement : 6 fine sand) for Terrace Floor including the cost of all materials

and labour charges etc. complete.

33 Providing and laying half brick work using common burnt clay building 29.80 Sq.m. 684.26

conventional type bricks having crushing strength not less than 35 Kg/Sq.cm

in cement mortar 1:4 (1 cement : 4 coarse sand) in cement mortar in super

structure for Ground floor including the cost of all materials and labour

charges etc. complete.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

34 Providing and laying half brick work using common burnt clay building 11.00 Sq.m. 690.57

conventional type bricks having crushing strength not less than 35 Kg/Sq.cm

in cement mortar 1:4 (1 cement : 4 coarse sand) in cement mortar in super

structure for First floor including the cost of all materials and labour charges

etc. complete.

35 Providing and fixing 150 mm wide, approved quality chicken wire mesh at 113.20 Sq.m. 295.12

junction of brick work and RCC work or two dissimilar surfaces, at all heights

fixed by nails, rowal plugs or tag by cement mortar 1:3 before applying the

plaster, including curing etc. complete

36 Providing 15mm thick cement plaster in single coat on rough (similar) side of 635.10 Sq.m. 226.01

single or half brick walls / concrete wall for interior plastering and finished

even and smooth along with floating coat of neat cement slurry etc. complete

in Cement mortar 1:4 (1-cement : 4 sand) at Ground floor.

37 Providing 15mm thick cement plaster in single coat on rough (similar) side of 353.30 Sq.m. 249.90

single or half brick walls / concrete wall for interior plastering and finished

even and smooth along with floating coat of neat cement slurry etc. complete

in Cement mortar 1:4 (1-cement : 4 sand) at First floor.

38 Providing 15mm thick cement plaster in single coat on rough (similar) side of 46.20 Sq.m. 273.80

single or half brick walls / concrete wall for interior plastering and finished

even and smooth along with floating coat of neat cement slurry etc. complete

in Cement mortar 1:4 (1-cement : 4 sand) at Terrace floor.

39 Providing 10 mm. thick smooth cement plaster in single coat for plastering on 185.60 Sq.m. 208.97

ceiling and soffits of stairs and finished even and smooth along floating coat of

neat cement slurry in cement mortar 1:4 (1 cement : 4 sand) (1) Plaster at

Ground floor.

40 Providing 10 mm. thick smooth cement plaster in single coat for plastering on 71.50 Sq.m. 230.86

ceiling and soffits of stairs and finished even and smooth along floating coat of

neat cement slurry in cement mortar 1:4 (1 cement : 4 sand) (1) Plaster at

First floor.

41 Providing 20mm thick double coat sand faced cement gutka plaster on walls 416.20 Sq.m. 345.75

with 1 x 1 cm grooves consisting of 12 mm thick backing coat of C.M. 1:3 (1

cement : 3 sand) and 8 mm thick finishing coat of C.M. 1:1 (1 cement :

sand) including 1 cm x 1 cm grooves etc. complete as directed by Engineer-in-

42 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 27.90 Rmt. 43.05

43 Applying two coats of acrylic lappy - putty & two coats of primer of approved 1291.70 Sq.m. 40.59

brand and manufacture on new wall surface to give an even shade including

thoroughly brushing the surface free from mortar dropping and other foreign

matter and sand papered smooth for all floors.

44 Wall painting (two coats) with plastic emulsion paint of approved brand and 1034.60 Sq.m. 82.85

manufacture on undecorated wall surfaces to give an even shade including

thoroughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth for all floors.

45 Wall painting (two coats) with plastic emulsion paint of approved brand and 257.10 Sq.m. 88.38

manufacture on undecorated ceiling surface to give an even shade including

thoroughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth for all floors.

46 Finishing wall with weather proof exterior 100% acrylic emulsion paint with 440.20 Sq.m. 120.26

one coat of primer on wall surface to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, dust and remains of loose

powdered materials etc. complete for all floors.

47 Providing and filling with good quality sinder (steam coal) as directed by 6.20 Cum 572.06

engineer in charge in sunks in layers of 15 cm thick including watering,

placing, ramming well etc. as directed for all floors.

48 Providing and laying controlled cement concrete M-200 for R.C.C. work and 1.30 Cum 5970.26

curing complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in coping on Ground floor.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

49 Providing and laying controlled cement concrete M-200 for R.C.C. work and 0.10 Cum 6011.80

curing complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in coping on First floor.

50 Providing and fixing 35mm thick solid core wooden flush double shutter 7.10 Sq.m. 3681.81

confirming to IS:2202 & ISI approved manufacturer, finished with 1mm thick

laminates on both sides of shutter, machine glued PVC beading on periphery,

S. S. handles and S. S. fixtures & locking arrangement of standard make of

kich or equivalent, on each shutter, fixed with minimum 4 Nos. 150mm high

S.S. hinges. Sample & shade to be approved by the Architect.

51 Providing and fixing 35mm thick solid core wooden flush shutter confirming to 18.90 Sq.m. 4848.84

IS:2202 & ISI approved manufacturer, finished with 1mm thick laminates on

both sides of shutter, machine glued PVC beading on periphery, S. S. handles

and S. S. fixtures & locking arrangement of standard make of kich or

equivalent, on each shutter, fixed with minimum 4 Nos. 150mm high S.S.

hinges. Sample & shade to be approved by the Architect.

52 Providing and fixing FRP frame size 100 x 50 mm and 28mm thick FRP 7.90 Sq.m. 2377.76

depress panel shutter having extra reinforcement on sides & edges in gel coat

finish. The core of the shutter & frame is to be filed up with injected fire

retardant grade polyurethene foam done in situ alongwith embedded wooden

pieces for stiffening & also taking hinges & fixtures. The whole FRP frame &

shutter is to be water proof, weather proof, termite proof & resistance to mild

acid/alkali. Rates are to be inclusive of S.S hinges with necessary screws &

alluminium fixtures & fastenings & fastener sleeve.

53 Providing and fixing window having two shutter glass section and one shutter 20.00 Sq.m. 2597.98

mosquito net extruded colour anodized aluminum section equivalent to Jindal

series E(30 mm) with sections numbered : frame bottom with weep holes-

20737, frame top & side - 20738; shutter top & bottom- 20993, shutter-inter

lock - 20550, shutter side (handle) - 20549, with 5 mm thick transparent tinted

float glass, with rubber gasket, air lock strip and finishing joints with

transparent silicon sealant, with standard extruded colour anodized aluminum

fittings. Window W1, W2 & W3.

54 Providing & fixing in position standard extruded approved colour anodized 2.70 Sq.m. 3944.65

Alluminum Ventilator with 3mm thick Bajari figure adjustable tinted louvers

glass fixed to alluminium strip blade including fixtures, fastening, labours and

equipments as per detailed drawing as directed. For Ventilators V1, V2.

55 Providing and laying Machine cut, free edges, mirror polished Granite Slab 12.50 Sq.m. 2368.24

flooring over 18mm (Average) thick base of cement mortar 1:6 (1-cement : 6-

coarse sand) laid over and jointed with grey cement slurry mixed with pigment

to match the shade of slab including rubbing and polishing etc. complete. (A)

18mm thick.

56 Providing and laying machine cut, free edges, mirror polished Granite Slab 4.80 Sq.m. 2338.22

18mm thick in risers of steps, skirting, dedo and pillars laid on 10mm thick

cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement

slury mixed with pigment to match the shade of slab including rubbing and

polishing etc. complete.

57 Providing and laying Vitrified tiles 8 to 10mm thick, 36'' x 36'' in flooring treads 83.70 Sq.m. 1531.82

of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-

cement : 3 coarse sand ) finishing with flush pointing in white cement.

58 Providing and laying Vitrified tiles 8 to 10 mm thick, in skirting, risers of steps 9.30 Sq.m. 1592.40

and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and

jointed with white cement slurry.

59 Providing and laying 24" x 24" Vitrified 8 mm thick tiles flooring over 20mm 99.40 Sq.m. 1467.72

(average) base of cement mortar 1:6 (1 cement : 6 coarse sand) on new

surface or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry including

finished with flush pointing & cleaning the surface etc. complete for Anti skid.

60 Providing and laying Vitrified tiles 8 to 10 mm thick, 24'' x 24'' in skirting, risers 7.30 Sq.m. 1195.02

of steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse

sand) and jointed with white cement slurry.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

61 Providing and laying white glazed tiles 6mm thick in flooring treads of steps 10.50 Sq.m. 890.26

and landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement :

coarse sand) finishing with flush pointing in white cement.

62 Providing and laying white glazed tiles 6mm thick in skirting risers of steps 69.70 Sq.m. 993.83

and dedo on 10mm thick cement plaster 1:3 (1-cement : 3 coarse sand) and

jointed with white cement slurry.

63 Providing and laying machine Kota stone slab flooring over 20mm (average) 16.60 Sq.m. 1019.39

thick base of cement mortar 1:6 (1-cement : 6- coarse sand) or L.M. 1.1.5 (1-

Lime putty :1.5 - coarse sand) laid over and jointed with grey cement slurry

mixed with pigment to match the shade of slab including rubbing and polishing

etc. complete. (A) 25mm thick

64 Providing and laying polished kota stone slab 25mm thick in risers of steps, 7.90 Sq.m. 1177.56

skirting, dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement :

coarse sand) and jointed with gray cement slury mixed with pigment to match

the shade of slab including rubbing and polishing etc. complete.

65 Providing Plinth Protection to building including excavation and laying cement 44.10 Sq.m. 2520.98

concrete 1:3:6 using stone aggregates of 40mm nominal size in foundation

layer 150 mm thick+ 125mm thick sand layer below pre-cast rubber dye inter

locking concrete block 60mm thick with grade of concrete M-300 pneumatic

compressed by mechanically pressed and as per approved design including

75mm sand layer for levelling and filling the joint with sand in proper line and

level etc. complete including providing and fixing precast concrete kerb stone

of grey cement based concrete block 30cm length, 30cm height and 15cm

thick made of M-250 grade concrete as per approved design and including

excavation for fixing in proper line and level, filling the joint with C:M 1:3 (1

cement : 3 fine sand) etc. complete.

66 Providing and laying broken china mosaic flooring for terrace using 12 mm to 112.00 Sq.m. 779.70

20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain

or slope and to be tempered to bring mortar creme out upto surface using

white cement including rounding off junctions and extending them upto 15 cm

along the wall, clearing with water and oxalic acid etc. as directed.

67 Providing and laying cement concrete flooring 1:2:4 (1 cement : 2 coarse sand 112.00 Sq.m. 347.42

: 4 graded stone aggregate 20mm nominal size) laid in one layer and finished

with a floating coat of neat cement. (B) 50 mm thick.

68 Providing and fixing mirror polished 18mm thick Granite with full round edge 53.20 Sq.m. 2553.90

and polished of approved quality in cladding on sill and around the doors /

windows / ventilation with 20 mm thick cement plaster CM (1:4) and fixing with

cement slurry & adhesive including moulding of exposed edges as directed by

engineering in charge etc. complete.

69 Providing and fixing M.S. Grills of required pattern to frames of windows etc. 41.20 Sq.m. 3095.77

with M. S. flats at required spacings and frame alround having min. weight of

grill 25 kg/sq.m. square or round bars with round headed bolts and nuts or by

screws including priming coat of approved quality and two coats of enamel

paint, as directed by engineer in charge (A) Plain grill.

70 Providing, erecting and fixing double coated I.S.I. Mark P.V.C. water tank of 2000.00 Litre 3.95

required capacity each with all necessary fittings and connection etc.

complete on terrace as directed.

71 Providing, laying and jointing in true line and level I.S.I. mark 110mm dia. 30.00 Rmt. 876.90

U.P.V.C. pipe (Type B) confirming to IS 13592-1992 with one end plain and

other end socketed with rubbering & fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of

the size 110 mm diameter x 149 mm length x 145 mm height at every

mm center to center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

72 Providing, laying and jointing in true line and level I.S.I. mark 160mm dia. 30.00 Rmt. 834.38

U.P.V.C. pipe (Type B) confirming to IS 13592-1992 with one end plain and

other end socketed with rubbering & fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of

the size 160 mm diameter x 210 mm length x 196 mm height at every

mm center to center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement including cost of all materials.

73 Providing, laying and jointing in true line and level I.S.I. mark 50mm dia. 90.00 Rmt. 195.67

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

74 Providing, laying and jointing in true line and level I.S.I. mark 40mm dia. 40.00 Rmt. 148.12

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

75 Providing, laying and jointing in true line and level I.S.I. mark 25mm dia. 50.00 Rmt. 91.84

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

76 Providing, laying and jointing in true line and level I.S.I. mark 15mm dia. 50.00 Rmt. 72.65

U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in

charge. Pipe shall be fixed on the wall with held of clamp at every two meter

c/c shall be concealed or open as directed including necessary fitting etc.

including testing of pipe and joints and fixing the same with adhesive solvent

including cost of all materials.

77 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 50.00 Rmt. 447.72

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (E) 40mm dia.

78 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 50.00 Rmt. 253.82

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (C) 25mm dia.

79 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 50.00 Rmt. 170.36

C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal

for potable water of following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc. complete. (A) 15mm dia.

80 Providing and laying (to level or slopes) and jointing reinforced concrete light 80.00 Rmt. 678.02

duty non pressure pipes I.S. Class NP-2 of the following internal diameter with

collars and butt ends prepared for collar joints including testing of joints

complete. (D) 300mm dia.

81 Providing, laying and jointing in true line and level I.S.I. mark 75mm dia. 50.00 Rmt. 756.22

U.P.V.C. SWR Type B pipe confirming to IS 13592-1992 with one end plain

and other end socketed with rubbering and fitting conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be jointed

with each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp at every 2000 mm c/c or shall be concealed in walls as directed

including necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement including cost of all

materials.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

82 Providing and fixing cast iron spigot and socket soil, waste and ventilating 30.00 Rmt. 741.01

pipes of the following nominal size. (B) 75mm dia.

83 Providing and fixing cast iron spigot and socket soil, waste and ventilating 30.00 Rmt. 892.39

pipes of the following nominal size. (C) 100mm dia.

84 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 10.00 No. 586.27

diameter with jali of the following nominal diameter of self cleaning design with

C.I. screwed down or hinged grating including the cost of cutting and making

good the walls.

85 Providing and fixing wash down water closet (European type W.C. pan) with 2.00 No. 3631.34

integral P and trap including jointing the trap with soil pipe in cement mortar

1:1 (1 cement : 1 fine sand) including providing and fixing plastic seat cover

for wash down WC with CP brass hinges and rubber buffers back plastic seat

and including providing and fixing PVC flushing tank with a pair of C.I. or M.S.

bracket with complete fitting such as lead valve siphon 15 mm dia. brass ball

valve with polythene float C.P. brass handle unions and couplings for

connection with inlet out let and over flow pipes 40 mm dia. porcelain

enameled flush bend including cutting holes in walls and making good the

same connection the flush bend with cistern and closet vitreous china etc.

completed.

86 Provision, supplying and fixing white vitreous china W.C. squatting pan Orrisa 2.00 No. 1638.03

type 580 x 400 size with 100mm P or S trap, 25mm dia. C.P. Brass flush valve

and G.I. inlet connection etc. complete. (A) Vitreous china long pattern white

87 Providing and fixing brass screw down stop tap. (A) 15mm dia. as approved 10.00 Each 205.83

by Engineer in charge.

88 Providing and fixing ball cock of approved quality as directed. (A) Copper 2.00 Each 189.84

Metal (iv) 50mm dia.

89 Providing and fixing wash basin with single hole for pillar tap with C.I. or M.S. 4.00 Each 1451.48

brackets painted white including sutting holes and making good the same but

excluding fittings. (A) Vitreous China (ii) Flat Back washbasin 550 mm x

400mm size. (i) In white colour.

90 Providing and fixing C. P. brass waste for wash basin or sink. (A) 32mm dia. 4.00 Each 67.91

91 Providing and fixing M.I. fisher union for washbasin or sink. (A) 32mm dia. 4.00 Each 78.75

92 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass 4.00 Each 859.41

mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden plug

with C.P. brass screws and washers.

93 Providing and fixing C.P. brass towel rail complete with C.P. brass brackets 4.00 Each 616.42

fixed to wooden plugs with C.P. brass scews (B) 600mm x 20mm size.

94 Providing and fixing screw down bib taps of following size.(A) Brass screw 4.00 Each 214.81

down bib tap polished bright. (ii) 20mm dia. as approved by Engineer in

95 Providing and fixing pillar tap, capstan head, screw down high pressure with 4.00 Each 308.73

screws, shanks and back nuts. (i) 15mm dia. as approved by Engineer in

96 Providing and fixing Urinal of approved quality including connection with trap 2.00 Each 1635.22

and with integral longitudinal flush pipe. (A) Squatting plate pattern white

earthenware 550mm x 300mm.

97 Providing and fixing Rubber plug for sink or wash basin. 4.00 Each 17.15

98 Providing and fixing chromium plated brass half turn flush cock of approved 2.00 Each 263.77

quality including fixing in pipe line etc. complete (ii) 25mm dia.

99 Providing and fixing S.W. Gully trap with C.I. grating brick masonry chamber 10.00 Each 1246.92

and water tight C.I. cover with frame of 300 x 300 mm size (inside) with

standard weight (i) square mouth traps (B) 150 mm x 100 mm size P or R type.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

100 Constructing brick masonry chamber for underground C.I. Inspection chamber 1.00 Each 2932.93

and bends with bricks having crushing strength not less than 35 Kg/cm2 in

C.M. 1:5 C.I. cover with frame (light duty) 455mm x 610mm internal

dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of

cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix (1-

cement : 2 coarse sand : 4 graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and bed concrete etc.

complete. (i) Inside dimensions 455mmx 610mm and 450mm deep for single

pipe line.

101 Constructing brick masonry chamber for underground C.I. Inspection chamber 1.00 Each 3660.76

and bends with bricks having crushing strength not less than 35Kg/Cm2 in

C.M. 1:5 C.I. cover with frame (light duty) 455mm x 610mm internal

dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of

cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix (1-

cement : 2 coarse sand : 4 graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and bed concrete etc.

complete. (ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe

line with one or two inlets.

102 Providing cement vata (10cm x 10cm size) quarter round in cement mortar 1:1 147.90 Rmt. 24.28

including neat cement finishing watering etc. complete.

103 Constructing a cooking platform 60 cm. width and 70 cm high resting on B.B. 6.60 Rmt. 2694.77

masonry walls 23 cm.thick in C.M.(1:6) with (i) Fixing or precast R.C.C. 1:2:4)

8 cm. thick slab with marble chips set in C.M. (1:6) (6mm thick terrazo) with

plastering on exposed faces walls in C.M. (1:4) etc. complete.

104 Clearing and grubbing road land including uprooting rank vegetation grass 0.10 Hect. 28455.09

bushes, shrubs, sapling and trees girth up to 300 mm removal of stumps of

trees cut earlier and disposal of unserviceable materials (C) By mechanical

means in area of light jungle.

105 Earthwork in cutting including preparing the slope, camber and stacking or 80.00 Cum 317.35

utilising the cutting stuff in bank as directed upto 200 meters from the end of

cutting with all lead and lift. (ii) Soft rock not requiring blasting.

106 Filling available excavated earth (excluding rock) in trenches plinth side of 67.00 Cum 136.92

foundation etc. in layer not exceeding 20 cm in depth consolidation each

deposited layer by ramming and watering etc. complete.

107 Rolling and watering of earthwork in layers with power roller including filling in 266.00 Cum 22.96

depressions which occur during the process as directed by Engineer incharge.

108 Providing & laying weep hole in abutments and returns by using A.C. pipe of 9.00 Each 86.73

100mm including laying in proper grade and jointing the completed as per

detailed specification.

109 Providing and fixing 610mm dia. Barbed Razor Tape Concertina Coil made 10.00 Rmt. 258.58

from hot dip galvanized spring steel high tensile wire (UTS: 145-160Kg/Cm2,

Zncoating 250-300g/m2, Diameter- 2.59+/-0.05mm), with blade of galvanized

Iron of 0.50 mm thick and width 19mm, with coverage / openable length of

10mtr/coil, including providing and fixing with clips, wires, bolt set con M.S.

angle posts, with all materials, labour, tools, tackles, etc. as per direction of

Engineer In-charge, for work at all level.

110 Box cutting the road surface to proper slop and camber for making a base of 23.50 Cum 109.41

road work including removing the excavated stuff and depositing on the road

side slope as directed for all lead and lift.

111 Providing and laying compacted WBM of Grading-II MCBT metal of size 45 to 9.00 Cum 1895.77

63mm in required layers including using 13% stone screening, 13.2mm size

and 7% stone dust as filler including spreading, watering & consolidation by

vibratory roller etc. complete.

112 Providing and laying controlled cement concrete M-200 and curing complete 8.00 Cum 4204.41

including the cost of formwork and excluding reinforcement for reinforced

concrete work in (A) Foundations, footings and Mass concrete.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

113 Compaction and finishing of cement concrete road by trimix process providing 51.00 Sq.m. 65.65

extra labour charges for the trimix vacume dewatering service process on

cement concrete road surface by using vacuum dewatering pump floater

surface vibrator including making grooves and rough finish to surface

including leveling etc. complete.

114 Providing and laying homogeneous grey cement based concrete kerbing of 23.00 Rmt. 374.92

size 30 cm x 30 cm x 10 cm size as per detailed drawing having grade of

concrete M-25 grade, including necessary excavation, BBCC 1:5:10, 7.5 cm

as per detailed drawing fixing in line and level, filling joints in C.M. 1:3 with

smooth finished, white washing three coats etc. complete as directed by

Engineer in charge.

115 Supplying premoulded bituminous joint filler 12 mm thick. 2.00 Sq.m. 553.79

116 Providing and laying (to level or slopes) and jointing reinforced concrete light 30.00 Rmt. 659.99

duty non pressure pipes I.S. Class NP-3 of the following internal diameter with

collars and butt ends prepared for collar joints including testing of joints

complete. (i) 300mm dia.

117 Drilling of pilot bore hole of size 250 / 300 mm diameter at above site by mud 75.00 Mtr. 865.57

finish direct rotary rig etc. complete.

118 Reaming of 250 / 300 mm diameter pilot bore hole to size 450 mm diameter 75.00 Mtr. 398.95

including assembling, lowering housing, casing strainer pipes with gravel

packing and clay ball packing etc. complete.

119 Providing 600 CFM / 150 PSI capacity air compressor up to availability of 1.00 Job 22427.05

sand free discharge (Minimum 6.0 Hours)

120 Supply of reducer made from 6 mm thick plate (M.S.) for ERW pipe of size (ii) 1.00 No. 1884.27

200 mm dia. x 250 mm dia. x 600 mm length

121 Supply of 200 mm diameter V-wire screen pipe of slot size 1.0 mm nominal 12.00 Mtr. 1767.28

hole etc. complete

122 Supply of M.S. bore clamps with 3 holes on either side with nuts and bolts of 1.00 Pair 1643.99

standard make and suitable size (g) 750mm x 75 mm x 16 mm flat to 200 mm

dia. pipe.

123 Supply of Bore Plug having 100 mm height made from M.S. plate with 3 holes 1.00 No. 782.57

at equal distance on circumference for nut- bolts type, locking arrangement

with nut- bolts & lock nuts of standard make complete. (B) from 5 mm thick

M.S. plate (for top also) (ii) suitable for 200 mm dia. pipe.

124 Supply of M.S. Bail Plug having length of 0.45 mtr from medium class pipe as 1.00 No. 851.04

per I.S.S. suitable for (d) 200 mm diameter pipe etc. complete.

125 Supply of Steel Bent plates suitable to ERW pipe for (b) 200 mm diameter and 4.00 No. 67.26

150 x 150 x 6 mm size etc. complete.

filling etc. complete.

127 Charges for uptron make Electrologger (with carting) of pilot bore hole etc. 1.00 Hour 12120.00

128 Charges for Geo Hydrological ground water investigation including water 1.00 Job 14428.86

sample chemical analysis etc. complete.

129 Supplying submersible pump set suitable for bore of 150 mm. dia. or more 1.00 Each 35590.38

having three phase motor capacity not more than 7.5 H.P. with following

capacity (a) (12 stage) 280 to 240 LPM discharge at 90 to 104 mtrs. head

respectively suitable for 50mm dia. delivery pipe

130 Providing and erecting PVC corrugated flexible conduit with required numbers 75.00 Mtr. 26.26

of coupling, PVC bushes, Check nuts etc. complete of following sizes. (3)

mm diameter.

131 Lowering of submersible motor pump set complete with required. Nos. and 1.00 Job 2568.43

size of casing pipes erected by means of proper chain pulley block & pipe

wrenches after checking of threads of each pipe with coupling to take the load

of the pump set and pipe assembly filled up with water. (b) Above 60 Mtr and

up to 120 Mtr

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

132 Supplying and erecting approved make motor control cubical panel (Direct - 1.00 Each 8710.24

on - line) made from 16 G. CRCA sheet duly epoxy powder painted inside and

outside with hinged doors and locking, arrangement consisting of suitable size

of ON-OFF isolator (AC - 3/23 duty) main fuses, single phasing preventer,

indicating lamps for R - Y - B phases, overload relay, automatic water level

wires duly socket crimped, main contactor & overload relay, start - stop push

buttons, to be erected on angle iron frame grouted on wall as directed. The

isolator, overload relay & contactors will be of L & T, Siemens or BCH make

only. (a) DOL up to 7.50 H.P.

133 Supplying and erecting XLPE (IS: 7098) (I)-88 ISI unarmoured copper cable 75.00 Mtr. 130.29

1.1 KV grade to be erected as directed of following size. (E) 3 core 2.5 Sq.mm.

134 Providing and supplying ISI mark CI D/F Butterfly Valves as per IS:13095 1.00 No. 1868.50

(Latest Edition) of following class and diameter including all taxes, insurance,

transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to departmental stores, stacking etc. complete. (B) Butterfly

valves IS 13095 with ISI mark PN 1.6 (1) 50mm

Electrical Items

135 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 55.00 Pt 485.81

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth continuity of following

type, erected on PVC / Metallic / Wooden box, single mounting base frame

covered with textured / metallic / white front plate modules erected on / in wall

/ ceiling as per pipe erected, with necessary lamp holder / ceiling rose / H.D.

Connector as directed.(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III.

(f) with medium class Rigid PVC pipe and accessories erected concealed in 10.00 Pt 242.91

wall / ceiling complete Cat. III (Half Point for Bathroom and WC)

136 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both 9.00 Pt 674.68

are of ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length, in below type of pipe erected with 6A Modular type

switch and hum free EME step type electronic fan regulator mounted and

accessories with earth continuity of following type erected on PVC / Metallic /

Wooden box, single mounting base frame covered with textured / metallic /

white front plate modules erected on / in wall / ceiling as per pipe erected with

necessary ceiling rose / H.D. Connector as directed. (f) with medium class

Rigid PVC pipe and accessories erected concealed in wall/ceiling complete

137 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both 16.00 Pt 510.05

are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected complete with Modular type

switch & 5 pin Plug erected on PVC / Metallic / Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories. [I] For 6A Plug and 6 a switch with

2-1.5 sq.mm Cu. Wire from nearby switch board / mcb db board (f) with

medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

138 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin 60.00 Pt 257.55

socket erected on PVC / Metallic/Wooden box, single mounting base frame

covered with textured / metallic / white front plate modules erected on / in wall

/ ceiling with following type accessories Cat. III

139 Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm & 10.00 Pt 167.66

earth wire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires, in below type of pipe to be erected

complete with earth continuity and necessary connection with primary light

with accessories erected on Metal / PVC / wooden box covered with 3 mm

thick PC (Polycarbonate) / Acrylic sheet for open / concealed wiring. with

necessary Lamp holder / ceiling rose / H.D. Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

140 Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire 8.00 Pt 603.98

of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires erected in below type of pipe with 6A

Modular type switches and following type of accessories erected on PVC /

Metallic / Wooden box, single mounting base frame covered with textured /

metallic / white front plate modules erected on / in wall / ceiling as per pipe

erected. with necessary batten / angle holder or ceiling rose or H.D.

Connector as directed. (f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

141 Providing following type of Modular Type Accessories mounted with PVC / 5.00 Ea 160.59

metallic / Wooden box, single mounting base frame covered with textured /

metallic / white front plate, modules erected with necessary connections as

per site situation directed by Engineer In charge.(3) Two Pin/RJ-11 Telephone

Socket [A] For One Gang Cat. III

(4) TV Co-axial Socket outlet Cat. III 4.00 Ea 160.59

(5) Electronic hum Free steps EME Fan regulator. Cat. III 3.00 Ea 398.95

(7) Blank Plate Single Cat. III 33.00 Ea 25.25

(9) 16 Amp. SP one way switch Cat. III 13.00 Ea 180.79

(10) 6/16Amp. Universal socket Cat. III 13.00 Ea 199.98

142 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following 112.00 Mtr. 24.24

size complete to be erected on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution & clamps with following

dia of pipes, in approved manner as directed (a) 20 mm

143 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 667.00 Mtr. 82.82

marked stranded Copper conductor wire in following type of pipe to be erected

concealed in / flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth continuity of following

size (A) With medium class Rigid PVC pipe and accessories (b) 2 wire

144 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 20.00 Mtr. 112.11

marked stranded Copper conductor wire in following type of pipe to be erected

in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of following size (A) with

medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq.mm

(g) 4 wire 4 sq.mm 20.00 Mtr. 180.79

(h) 4 wire 6 sq.mm 25.00 Mtr. 260.58

145 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv 20.00 Mtr. 46.46

grade ISI marked copper wires of following size to be erected as directed.(e)

1.50 Sq.mm 3 core round PVC sheathed

146 Providing & erecting approved make following size of TV Co-axial flexible 60.00 Mtr. 62.62

cable comprising inner conductor of solid bare copper insulated with Foam PE

& Secondary conductor made of poly - Aluminium film bonded Al. Braids @

suitable coverage overall sheathed with black PVC insulation.(e) RG-11

147 Supplying & erecting approved make Telephone Cable electrolytic copper 100.00 Mtr. 20.20

conductor PE insulation twisted in two pairs & wrapped with FRLS PVC tape &

sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone wiring

& confirming to C-DOT erected in existing pipe of following size of conductors

& nos.of pairs with necessary connections. [A] Conductor Size 0.5 mm (a)

Unarmoured (2) Two Pairs

148 Providing & erecting main Distribution (MDF) indoor type, back mounted frame 1.00 Mtr. 994.85

as per DoT standard approved with krone strips (a) Suitable for 10 pair

149 Bakelite adopter for Holder to be erected. 10.00 Ea 9.09

150 Decorative call bell Ting-tong box type 250 volts complete erected 1.00 Ea 71.71

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

151 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 11.00 Ea 373.70

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more than 0.95, THD <

15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt, LED

LED driver efficiency > 85% (fitting required LM-79 & LM-80 Certificates)

(NOTE: Below description have shown ranges of Wattage capacity of LED

ranges shown) (A) Tube Light with integral driver (iv) 22-24 Watts, Surge -

2KV, IP-20, conventional 4 feet Cat-lll

152 Supplying and erecting led lamps with following wattage capacity of 220 to 4.00 Ea 188.87

240 voltage, minimum 15000 burning hours life, 500 V in built-surge

protection, Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser suitable

LAMP holder (iii) 10 to 15 watts Cat-lll

153 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 29.00 Ea 427.23

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure

die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name 160V to

270V,Power Factor more than 0.95, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt, LED driver efficiency > 85% (fitting

required LM-79 & LM-80 Certificates) (NOTE: Below description have shown

any wattage capacity between the ranges shown) (A) Square/ Circular shaped

Surface / Recessed Mount Downlight with provision for spring loaded

mounting clips complete. IP20 (ii) 11-15 watts, Surge-2 KV Cat-lll

(iv) 22-24 watts, Surge-2 KV Cat-lll 27.00 Ea 758.51

(H) Mirror Light 9 Watts, wall mounted minimum 1 feet long 4.00 Ea 312.09

154 Supplying and erecting LED street light / Flood light fittings with High power 8.00 Ea 4997.48

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or embossed 160 to 270 V, Power

Factor more than 0.95, THD < 10%, CCT 3000 K to 5700K, Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85%.

(fittings required LM-79 & LM-80 certificates) (NOTE: Below description have

shown ranges of Wattage capacity of LED fittings. The Engineer incharge may

65), Surge protection -4KV integral and Light must have 440VAC line supply

with over-voltage protection. (ii) above 48 to 60 Watts Cat-lll

(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot and 2.00 Ea 4092.52

spun aluminum canopy fixed with opal polycarbonate, pipe arrangement for

vertical mounting driver and accessories wired upto terminal block. IP 65 (i)

20- 30W Cat-lll

155 Providing and erecting Miniature circuit breaker single pole 0.5A to 2A system 10.00 Ea. 270.68

and having breaking capacity 10 KA to be erected in existing box confirming

to IS 8828/1996 with ISI Mark Cat III

156 Providing and erecting Miniature circuit breaker single pole 6A to 25A suitable 30.00 Ea. 112.11

to operate on 240 V A.C. system and having breaking capacity 10 KA to be

erected in existing box confirming to IS 8828/1996 with ISI Mark Cat III

157 Providing & erecting 240 V MCB double pole switch for motor & inductive load 5.00 Ea. 299.97

(C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing

box having following capacity (A) 6 to 32 Amp. Cat III

(B) 40 Amp. Cat III 2.00 Ea. 330.27

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

158 Providing & erecting 240 V MCB double pole switch for lighting Load (B 1.00 Ea. 278.76

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box

having following capacity (A) 6 to 32 Amp.Cat III

159 Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C 1.00 Ea. 587.82

Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box

having following capacity (a) 6 to 32 Amp. Cat III

(b) 40 Amp. Cat III 1.00 Ea. 647.41

(c) 63 Amp. Cat III 2.00 Ea. 716.09

160 Sheets steel powder coated enclosure suitable for incorporating One/Two 4.00 Ea. 176.75

161 Providing and erecting Sheet Steel powder coated MCB distribution board - 1.00 Ea. 1152.41

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs. (The DBs should be used of same company of

MCB to be used) suitable for (A) single phase incoming and horizontal single

phase outgoing (b) sheet steel double door (IP-43) (iii) 8 way

(iv) 12 way 1.00 Ea. 1492.78

(B) three phase incoming and single phase horizontal type outgoing per phase 2.00 Ea. 2339.16

isolation type (PPI) (b) sheet steel double door (i) 4 way

162 Providing and erecting Approved make RCCBs conforming to IS: 12640 and 7.00 Ea. 2235.13

having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V, 50Hz. having characteristic of

quick action & tripping with all advance feature & do not incorporate any

electronic component. for following Max. rating erected as directed (i)

Amps. DP Cat III

163 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. 2.00 Ea. 368.65

dia. galvanised iron pipe with coupling and buch buried in specially prepared

earth pit complete with necessary 8 SWG earth wire.

164 For using salt and charcoal / coke as required for pipe type earthing. 2.00 Ea. 171.70

165 Providing and erecting Steel cover as per drawing using 16 SWG M.S.sheet 0.20 Sq. 2560.35

of following depth, to house the switch gear etc. complete with locking Mtr.

arrangement and lock with duplicate keys per cupboard and door handles

erected with necessary support and painting. [One coat red oxide and two

coat enamel paint] (B) Without angle iron frame (i) For 25 cms. Depth

166 Providing and erecting Meter cover made from multi chamber hollow PVC 1.20 Sq. 3339.06

sections of 20 mm thick having all the corner joints with PVC solution angles Mtr.

without using any screws, nails shutters having required size of eye glass and

with necessary locking arrangement hinged with box. The back of meter box

should be fixed with timber. Hold fast for holding screws or nut bolts.

167 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable Aluminium 166.00 Mtr 92.92

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables. (B) 2 core 6 Sq.mm

(C) 2 core 10 Sq.mm 35.00 Mtr 126.25

168 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / 35.00 Mtr 140.39

Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of cables (C) 4 core

169 Making trench in soft soil of suitable width of 90 cm deep for laying cable or 75.00 Mtr 55.55

locating the fault all over the run and back filling the same and making the

surface as normal ground.

170 Providing & laying approved make Double walled corrugated pipes (DWC) of 112.00 Mtr 62.62

polyethylene (conforming to IS 14930 II) with necessary connecting

accessories of same material at required depth in existing trench for laying of

cable below ground / road surface for enclosing cable (A) 50 mm outer dia.

171 Providing and fixing heavy duty flange type brass cable gland with rubber ring 20.00 Ea 38.38

for PVC insulated armoured cable complete with out going tails, insulating

tape etc for following size of cables.(B) 2 to 4 core 6 Sq. mm

(C) 2 to 4 core 10 Sq. mm 4.00 Ea 38.38

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

172 Solder less crimping type Aluminium lugs conforming to IS suitable for cable 40.00 Ea 6.06

of following size evenly crimped with high pressure tool & connected to

switchgear terminals with brass/cadmium plated nut bolts in an approved

manner. (A) 1.5 / 2.5/4/6 Sq.mm

173 Providing and erecting Approved make Ceiling fan with double ball bearing 13.00 Ea 1596.81

ISI mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete,

canopy erected on existing hook or clamp with earthing. [Make shall be

approved by Engineer in charge]

174 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe 13.00 Mtr 108.07

down rod erected duly painted for fan complete with proper insulation without

leakage and earthing.

175 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the 28.00 Ea 108.07

RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S.

box / Heavy Duty PVC box complete erected concealed in Ceiling with

necessary finishing.

176 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan 28.00 Ea 18.18

177 Supplying & erecting approved make low noise decorative exhaust fan having 3.00 Ea 1703.87

square frame ABS body with inbuilt lowers & square frame. 200mm with

RPM Cat.II

178 Supplying & erecting single phase approved make industrial exhaust fan 1.00 Ea 2054.34

suitable for medium duty ring mounted low noise operation suitable for

medium duty having following dia size and maximum speed in RPM [A]

mm dia. 900 RPM Cat.II

179 Supplying & erecting approved make SMC press moulded composite FRP 10.00 Ea 476.72

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector strip

5way (3P+N+E), DIN rail for mounting mob & hinged doors as per requirement

having locking arrangements with mounting clamp with nuts, bolts & washers

suitable for erection on pole with cable clamps & earth bolt of following size of

box. (C) 150mm x 125mm x 100mm [deep]

(A) 300mm x 200mm x 100mm [deep] 1.00 Ea 898.90

180 Supplying and erecting B class Galvanized iron pipe having smooth finished 12.00 Mtr 215.13

bore of the pipe on both ends erected nuts and bolts along the pole / wall

shaping the pipe as per site requirement. Pipe dia as following.(B) 32 mm dia.

181 Supplying and erecting HYLAM sheet on existing angle iron frame for 1.00 Sq. 771.64

following thickness (B) 4mm Mtr.

182 Supplying & erecting approved make Digital time switch having lithium cell 6 1.00 Ea 3168.37

years operative and operate battery backup 1 channel day clock with

memory programme, suitable to operate on 240V + 5%, 16A with, floating

contacts Minimum switching setup time 1 minimum & LCD display. Also

comprised permanent ON/OFF switching. Programming switches & housed in

fire proof thermoplastic enclosure & transparent cover erected as required

with necessary connection erected as directed.

183 Supplying & erecting power contactor, AC3 duty for time switch complete 1.00 Ea 1883.65

erected as per direction Cat III (B) 2 pole 250V 32 Amp.

184 Supplying & erecting approved make motor control cubical panel (Direct - on - 1.00 Ea 7722.46

line) made from 16 G. CRCA sheet duly epoxy powder painted inside and

outside with hinged doors and locking, arrangement consisting of suitable size

of ON- OFF isolator (AC - 3/23 duty) main fuses, single phasing preventer,

indicating lamps for R- Y - B phases, overload relay, Automatic water level

wires duly socket crimped, main contactor & overload relay, start - stop push

buttons, to be erected on angle iron frame grouted on wall as directed. The

isolator, overload relay & contactors will be of L & T, Siemens or BCH make

only. (A) DOL up to 5.0 H.P.

185 S.I.T.C. of single phase submersible pump set suitable for 100 mm size or 1.00 Ea 18386.04

more dia bore well having motor capacity and discharge as under with

necessary panel box. Lifting and Lowering taken extra. (c) Motor rating 2 HP

(17 stage) pump having capacity of 106 LPM at 40 mtr head suitable for

mm dia. delivery pipe Cat.II

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

186 Lowering of submersible motor pump set at the depth of following, complete 1.00 Per 1711.95

with required. Nos. and size of casing pipes erected by means of proper chain Job

pulley block & pipe wrenches after checking of threads of each pipe with

coupling to take the load of the pump set and pipe assembly filled up with

water (A) Up to 60 mtrs.

187 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible 65.00 Mtr. 104.03

Submersible copper cable approved make of following size. (B) 3 Core x

188 Supplying of following size of STANDARD UPVC column pipe with coupler 40.00 Mtr. 179.78

and wire lock [B] 32 mm dia

189 Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) 1.00 Per 462.58

long, pump guard set, starter pipe Rubber ring for submersible pump & UPVC Set

column pipe as directed by Engineer - in - charge with necessary plumbing as

desired.[B] 32 mm dia.

Total Rs.

i.e. Rs. Seventy Four lacs Eight thousand Six hundred Sixty Six and Fourty Nine paisa only.

I/We am/are willing to carry out the work @ ______________ % above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

Net Rs. ___________________________ Total Rs. ________________________

In words ____________________ In words ____________________

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is

a change as per actual mix design the cost of difference of cement consumption have been deducted from the

rate of original item at the rate of input rate mentioned in all the tender.

5. The Contractor will have to submit the all required mix design at his own cost before execution as

directed and to be approved from the Engineer in charge.

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and found

Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer

Lunawada (R & B) Sub Division, Mahisagar (R & B) Division, Mahisagar (R & B) Division,

Lunawada Lunawada Lunawada