SPL REPAIR TO SINGLE LIVING OTM ACCN BLDG NO. P-129 AT ARMY AREA JODHPUR UNDER GE (A) NO. 01

Amount

Demolition of Cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness and removing from site as directed by Engr-in-Charge complete all as specified.

M&L for laying 40-50 mm thick Machine cut sand stone slabs as in Plinth protections laid over 20 mm thick cement sand screed in CM1:4 over 50 mm thick PCC 1:3:6 all as specified and directed incl filling the joints of sand stone slabs with neat cement mixed with pigment to match the shade of slabs complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar.

M&L for 75 mm thick Cement concrete type D-2, 1:4:8 (40 mm graded agg) as in sub base to floors incl well compacting & laid to levels all as directed.

M&L for Chequered cement concrete tiles, rubber moulded 300mm x 300mm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement with pigment in floors over 20mm thick screed bed in CM (1:4) complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying if inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete.

Taking down carefully cement concrete/ spalled out concrete from RCC roof projections,Ceilings,Sunshades of beams etc upto cover depth by chipping out lightly including necessary scaffolding at height up to 7.5 mtr etc complete.

M&L for cleaning, sweeping out loose materials from the existing reinforcement of slabs chajjas etc & applying a coat of SIKA RUSTOFF 11 or equivalent of pidilite,fosroc,Thermax etc to remove rust particles etc throughly cleaning the surface.

M&L for applying a coat of bond coat made with cement slurry (1part cement to 1.5-2parts water) mixed with admixture LATEX POWER mixed @ 5 Kg per 50kg of cement & applying to the concrete surfaces @200gm/sqm to obtain tack.

M&L for 15-20mm thick rendering in CM 1:1:2 using 1 part cement to 1part 2-3mm screenings of stone agg & 2 parts coarse sand over the bond coat applied surfeces with cement mixed SIKA PLASTOCRETE admixture or equivalent of pidilite, fosroc, Thermax etc @100gm/50kg of cement & finishing the surfaces even & rough to recieve final rendering coat.

M&L for 10-15mm thick rendering in CM 1:3 over the bond coat applied surfeces with cement mixed SIKA PLASTOCRETE SUPER admixture @100gm/50kg of cement & finishing the surfaces even & smooth complete all as directed at site.

S&F GI chicken wire mesh of 0.71mm dia wire & 12mm mesh size fixed with nails & screws around RCC chajjas /fascias, slabs, beams etc complete all as specified & directed.

Taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 finished even and smooth without extra cement on stone wall surface complete all as specified & directed.

M&L for rendering 15 mm thick in two layers of 10mm thick on stone masonry surface in CM 1:6 and top layer of 5 mm thick in CM1:4 incl finishing the surface fair and even without using extra cement and using integral water proofing compound in top layer. Note :- WPC shall be measured & paid for separately.

M&L Rendering 10 mm thick CM (1:3) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth complete all as specified & directed.

Racking out joints/pointing to square rubble masonry Jodhpur type regular coursed built in cement mortar all as specified

M&L for Keyed pointing to square rubble masonry Jodhpur type regular course in CM 1:3 all as specified.

Demolition of stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified & as directed.

M&L for squarred rubble walling Jodhpur type regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6 complate all as specified and directed.

All as per item No 21 above but except stone complate all as specified and directed.

Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete all as specified and directed.

M&L PCC solid building blocks 10 cm thick type B1 1:2:4 set in cement mortar (1:6) complete all as specified and directed.

M&L for Plain cement concrete 1:2:4 type B0 using 20mm graded crushed stone aggregate as in coping to parapet walls including necessary form work complete all as directed.

M&L for Plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in roof kerbs rounded or chamfered on edges as specified

M&L for cutting in to old masonry to form toothings for bonding in new brick or stone work including making good in cement mortar 1:6 complete all as specified and directed.

M&L sand stone slabs in sunshades, chajjas, shelves, cills, landings cover stones templates etc n exc 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4 thickness of slab 5cm complete

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L for 25 mm thick PCC type B-0 1:2:4 (12.5 mm graded aggregate) as in sub bases floors of tiles all as specified.

M&L for non-skid coloured ceremic tiles joint less 7 to 8 mm thick area of each tiles exceeding 0.18 Sqm but n.exc. 0.38 sqm in floor etc set jointed in neat cement slurry and pointed in white or coloured cement to match the shade.including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per item No. 31 above but skirting includig 10 mm thick rendering in CM 1:3 complete.

M&L non skid ceramic colour joint free tiles 6 to 7 mm thick of size area exc 0.11Sqm but nexc 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed .

M&L for glazed colour ceramic tiles of size 300x 600x 7-8mm/ 450X 350X 7-8mm, laid in vertical surface of dado/ skirting joint free etc, set and jointed in neat cement slurry and pointed in coloured tiles to match the shade of tiles includig 10 mm thick rendering in CM 1:3 complete all as specied and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for 18-20mm thick machine cut Kota stone slab as in flooring staircase, riser & treads of steps etc over screed bed base ,laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing, grinding and polishing including 20mm thick screed bed in cement mortor 1:4 complete all as specified and directed.

Ditto as per Item No. 36 above but herein riser of steps, skirting, dado and pillar laid over including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L Udaipur Green marble 16-18mm thick as in cills, platforms of WHB, treads of steps etc over cement screed 15mm thick in cement mortar 1:4 laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, moulding and mirror polishing complete all as specified and directed. Note: Quoted rate deemed to including the cost of chamfering the exposed edges of marble.

M&L Udaipur Green marble 16-18 mm thick (table rubbed and polished) in riser of steps, jambs, pillars and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 10mm thick plaster 1:3 all as specified and directed.

M&L for 18-20 mm thick Black granite stone as in cooking platforms, slabs for oval type WHB,sinks/cills etc & the likes complete laid over 15 mm thick cement sand screed in CM 1:4 incl mirror polishing complete & providing necessary holes for gas pipe complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L for treating existing the surface of kota stone floors surfaces of dado/skirting with bees wax polish including rubbing, grinding and polishing, cleaning and preparing the surfaces complete all as specifiied and directed.

Complete removal of existing treatment and preparation of wall/ceiling surfaces of any description complete all as specified.

M&L for Preparation of new un-decorated plastered/ concrete of ceiling and applying three coat of white wash complete all as specified.

M&L for Preparation of old decorated plastered/ concrete of ceiling and applying one coat of white wash complete all as specified.

M&L for Preparation of old decorated plastered/ pointed /concrete of walls and applying three coat of white wash complete all as specified.

M&L for applying 2 coats of Oil Bound distemper over 1.5mm to 2mm thick wall putty finished to a even and smooth finish over a coat of alkali primer complete all as specifed directed by Engg-in-charge.

Complete removal of existing treatment of cement base paint on existing surfaces of wall and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M & L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of surfaces completeall as specified and directed.

M & L applying two coats of synthetic enamel paint on old wooden surfaces of any description over 10 cm width or girth over including preparation of surfaces complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on old steel surfaces of any description over 10 cm width or girth including preparation of surfaces complete all as specified and directed.

M & L for mild steel framed work as in brackets etc for cooler stands,supportings frame work for sun shade etc framed steps/stairs etc complete using MS railing/angle iron Steel bars gusset plate etc conforming to Fe-290 Gde E-165 complete all as specified & directed complete.

M &L for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of syn enamel paint on int surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all specified and directed.

Taking down shutter of any description, exc. 1 Sqm but n exc 2 Sqm and re-fixing in the same opening after necessary repair like easing etc. complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 Sqm but not exceeding 4 Sqm each with shutter without taking off shutter from the frame complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frames) area nexc 1.50 Sqm & removal to store

S&F of pressed steel frames of size 165x60mm for doors with one or more rebates incl necessary fixing lugs,hinges,lock strice plate including a shop coat of red oxide primer etc complete all specified & directed.

S&F of pressed steel frames of size 105x60mm for doors with one or more rebates incl necessary fixing lugs,hinges,lock strice plate including a shop coat of red oxide primer etc complete all specified & directed.

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing & Fixinng Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F 40mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face covered with decorative face veneer/mica with 40x2mm lipping/frame to match, complete all as specified and directed.

S&F 2nd Calss hardwood 35 mm Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc.(without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & as directed.

M&L PCC (1:2:4) type B-0 using 12.5 mm aggregate in filling pressed steel frame, concrete shall be compressed all as specified and directed.

Taking down of steel window and ventilators, complete all as specified and directed.

S&F of factory made steel window box type with side hung shutter as shown on drawing No CEJZ/TD/20 sheet 1/3 to 3/3 complete with glazing bars, dovetailed or welded complete all as specified and directed. Note:- Both shutter jointed internally with flat iron 40x4mm complete including grill of 10mm square bars as directed by Engineer incharge, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. (with provision of fixing for cooler if required)Guard bar/ grill/glazing/painting/wire cloth shall be measured and paid separately under respective item of Sch 'A'.

S&F of factory made steel window box type with side hung shutter as shown on drawing No CEJZ/TD/20 sheet 1/3 to 3/3 complete without glazing bars, dovetailed or welded complete all as specified and directed. Note:- Both shutter jointed internally with flat iron 40x4mm complete including grill of 10mm square bars as directed by Engineer incharge, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. (with provision of fixing for cooler if required)Guard bar/ grill/glazing/painting/wire cloth shall be measured and paid separately under respective item of Sch 'A'.

S&F Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified

S & F 4 mm thick pin headed figured glass in small widths as in louvers of ventilators complete all as directed.

S&F 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

S&F stainless steel wire cloth, 0.71mm nominal dia of wire and average Size of mesh in 12mm and fixed with tinned tacks, or stainless steel wire staples complete all as specified & as directed.

M&L for Mild steel square bars welded to steel windows or ventilators as in guard bars framed or unframed conforming to Fe 290 Gde E-165 complete all as specified & as directed. Note :- Guard bars shall be factory welded & given one shop coat of red oxide or zinc chromate primer. Cost of factory welding & Shop coat of primer is deemed to be included in quoted rates.

S&F of aluminium anodized,tower bolt 200 mm long complete all as specified and directed.

S/F of aluminium anodized,tower bolt 150 mm long complete all as specified and directed.

S&F aluminum anodised handle extruded section of size 150mm long complete all as specified and directed.

S&F of aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long complete all as specified and directed.

S &F of stainless steel butt hinges 100 mm size medium weight complete all as specified and directed.

S &F of mild steel butt hinges 100 mm size medium weight cold rolled complete all as specified and directed.

S&F 125 mm size single action door spring hinge mild steel with steel wire spring stove enamelled black complete all as specified and directed.

S & F floor door stopper of alluminium alloy body and toungue anodised with hard drawn steel spring 140mm long complete all as specified and directed.

M/L for PCC 1:2:4 type B1 Mix using 20mm graded stone aggregate as in hold fast iron fixing including necessary form work all as specified.

S&F flat iron for hold fast and similar work confirming to Fe-290 Gde-E-165 fixed with welding and necessary item complete all as specified and directed.

M&L for Providing precast cement concrete type B-0 1:2:4 (12.5mm graded aggregate) set in CM 1:4 for louvres and jallies, cement grill any type model of zafri 25mm thick (measured solid), including all mould- ings complete all as specified and directed.

Supply and fixing in repairs decorative type curtain rod stainless steel finish of pipe 22 to 25 mm dia as per sample.

Supply and fixing of purpose made brackets trade pattern for decorative type curtain rods suitable for holding 22 to 25 mm dia as per sample as in repairs.

Supply and fixing in repair of decorative fincals (round type with mirror optic finish) trade pattern for decorative type curtain rods suitable for 22 to 25 mm dia curtain rods as per sample kept in GE's office.

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 110mm bore as directed

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 75mm bore as directed

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls including GI stack clamp out of 30mm by 4mm flat iron and 12mm dia round stays bolts and nuts and securing ends of stays

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls including GI stack clamp out of 30mm by 4mm flat iron and 12mm dia round stays, bolts and nuts and securing ends of stays

S&F 75 mm bore PVC (SWR) bends any radius

S&F 110 mm bore PVC (SWR) bends any radius

S&F 100mm bore pipe PVC (SWR) vent cowls, complete all as specified.

S&F 75mm bore pipe PVC (SWR) vent cowls, complete all as specified.

M&L WC Connector 110 mm PVC SWR for WC complete all as directed.

M&L in repairs PVC (SWR) floor trap plain with SS grating including jointing with solvent cement 75mm dia of outlet.

S&F as in repairs 15 mm dia angular stop cock cast copper alloy with chromium plated long thread with flange complete

S&F as in repairs of 15 mm dia cast copper alloy bib taps long body with flange with chromium plated fixed with iron pipe complete all as specified and directed.

S&F as in repairs of vitreous china clay water closet squatting pan ORISSA Pattern size 580x 440 mm white with integral foot rest incl 'P' or 'S' traps, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish all as specified and directed.

S&F as in repairs vitreous china wash down water closet European Type pedestal pattern with seat & cover as in repairs with jet spray complete incl fixing of flush pipe etc complete all as specified and directed.

Supply & Fixing only low level flushing cistern PVC 10 ltrs capacity with float valves (ISI Marked) white with inlet ball valve complete (Rates for Fixing of Flushing Cistern included with the fixing of WC)

S&F as in repairs Vitrous china coloured/white wash basin, white flat back size 550x400 mm including , waste fittings, waste pipe, MS brackets,chromium plated and waste coupling(32mm dia) complete all as specified and as directed.

S&F as in repairs fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm dia bore.

S&F in repairs Vitreous China Half stall urinal complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe including wate coupling and waste pipe of sitable diameter and length complete all as specified and as directed.

S&F health foucet with 1200 mm long flexible mild steel tube 80 mm dia with wall hook complete all as specified and directed.

S& F overhead shower 100 mm dia of ABS body chromium plated with gray face plate with arm having swivel joint chromium plated complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm all as specified and directed.

S&F in repair Soap dish any type, fixed to plugs with chromium plated brass screws all as specified and directed.

S&F in repair tubular towel rail 20mm dia brass chromium plated `D' type 60cm long with bracket and fixed complete all as directed

Dismantling existing tanks of any description n exc 1000 ltrs capacity and removing from site.

S&F 1000 ltrs capacity white colour Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl fixing arrangment for inlet/outlet/overflow & vent pipe of standard size complete all as specified & directed by Engineer-in-charge.

Supply only 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & 3, plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) all as specified & directed.

S &F in repair 25 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 25mm dia all as specified specified.

Supply only Integral water proofing compund

Taking down or up steel tubing and connection including cleaning for refixing or removal to store

(a) 25 mm dia

(b) 20 mm dia

(c ) 15 mm dia

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

(a) 25 mm dia,

(b) 20 mm dia

(c )16 mm dia including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc complete.

Demolition of cement concrete in roof padding damaged /loosed cement concrete /bricks tiles from roof /terrace to a depth of average 50 mm including dismantling of existing treatment with APP membrane if any cleaning with water and depositng of debris outside MoD land complete al as specified and directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in padding over old cleaned surface of any description on roof/terrace to fill any depressions etc or to obtain desired slopes.

M&L for 15mm thick rendering in CM 1:3 finished even and smooth without extra cement on concrete roof surface with WPC complete all as specified & directed. Note : WPC will measured and paid saparately

M&L for preparing new surfaces of roof and applying two coats of Polyurethane (PU) acrylic based water proofing liquid compound over and including a coat of diluted elastomeric self primer and reinforcement fabric sheet as per manufacturer’s instruction to stop leakage / seepage from roof / wall complete all as specified and directed.

M&L for cleaning and removal of loose concrete, prepare the sunken portion for treatment, filling the crackes with polymer modified mortar using Dr fixit pidicrete URP in the ratio of 1:3 by adding polymer 10% by weight of the cement add the water little unit the required consistancy is achived and thereafter providing and alying two coats of acrylic polymer modified cementitious coating Dr Fixit pidifin 2K of M/s pidilite industries having elongation at break 50%, 5 Bar resistance to positive water pressure, adhesive strength ASTM D 7234-1 N/mm2 water vapor transmission as per ASTM E96 of 0.3 perms and crack bringing ability as er EN 1062-7 upto 1mm. Apply two coats of Dr Fixit pidilte 2k slurry @ coverage of 0.55 - 0.58 Sqm/Kg of mix slurry. Provide and lay45 gsm glass fibre mess over the angle fillet when the first coat install wet. Allow the first coat to dry for 6 to 8 hrs, then apply the second coat at a direction perpendiculer to the first coat. Allow the coating to air cure for 5 days before conducting water ponding test for 24 Hrs etc or other equivelent product as approved by GE in Sunken area comlete all as per manufacturer instructions, including removing of rubbish materials from building and thrown in low laying empty area at any distance out side MD land complete all as specified and as directed by Engr-in-Charge.

Demolition of Reinforced cement concrete (reinforcement cut as required to facilitate demolition) n exc 15cm thickness and removing from site complete all as specified.

M&L for Reinforcement cement concrete (nominal mix) type A-1, 1 : 11/2 : 3 (using 20mm graded aggregate) as Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr-in-Charge.

M&L for Reinforcement cement concrete (nominal mix) type A-1, 1 : 11/2 : 3 (using 20mm graded aggregate) as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge.

Use and waste Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat complete all as specified and directed by Engr-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; exc. 200m thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and directed by Engr-in-Charge.

S&F Mild steel TMT bars 10mm dia and over cut to length bend to shape reqd incl cranking, bending and binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engr-in-Charge.

Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site as directed.

Taking down carefully UNSV submain wiring of any size and all as directed.

M & L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core FRLS cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces ) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete all as specified, directed. The rates of chase cutting on wall done concealed conduit and steel terminal boxes are included in the unit rates all as specified and directed by Engr-in-Charge.

One light point controlled by one, one way switch

One fan/ Exhaust Fan point controlled by one way switch.

One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

One light point controlled by two, two-way switches

All as per srl item no. 137.00 here-in-before but with 4 sq mm FRLS copper wire with 4 Sqmm FRLS copper earth wire for indpendent 15 Amp point.

All as per srl item no. 137.00 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for indpendent 15 Amp point.

S&F Switch piano type, single pole, one way, 6 amps, 230 volts,ISI Marked complete all as specified and directed.

S&F Socket, 3 pin, 5 Amp, universal type, 230 volts, ISI Marked complete all as specified and directed.

S&F Switch piano type, single pole, one way, 16 amps, 230 volts, ISI Marked complete all as specified and directed.

S&F Socket, 6 pin, 6/16 Amp, multipurpose shutter type, 230 volts, ISI marked complete all as specified and directed.

S&F Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed.

S&F LED lamp 9W complete all as specified and directed by the Engineer-in-Charge.

S&F Ceiling rose, three terminals, bakelite body, 230 volts, ISI Marked complete all as specified and directed.

S&F resistance type regulator Socket type stepped type A/C 240 Volts, ISI Marked.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including AC decorative box type with driver, holder including,copper conductor cable of suitable size from ceiling rose complete complete, 4 ft long all as specified and directed.

S&F bldg security LED Light Luminaire of 35 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI pipe 40 mm bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable complete all as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high ,efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

M&L for taking down old U/S serviceable fan and refixing in same position after painting, Greasing , winding, bearing replacing, suitable size down rod including provision of copper flexible twin core cable of size 23/0.0076 from ceiling rose or connector to fan for connection

S&F Vertical Distribution Board, double Door, suitable for 'A' Frame FP MCCB 100A made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, TPN 6 way, 415 volts with bus bar rating 300 Amps, dust and vermin proof, suitable for incorporation of MCB’s and MCCB etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Note : MCCB & MCB will be measured and paid separately under respective items

S&F MCCB, A Frame, thermal adjustable magnectic setting, Ics = 75% 25 kA, 415V, 100 Amp, 4 Pole MCCB with over load and short circuit protection, complete all as directed.

S&F MCB, B Curve type, 10 kA, 63Amp, SPN with over load and short circuit protection, complete all as directed.

S&F MCB, B Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed.

Supply and fixing as MCB DB SPN (double door) 8 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall all as specified and directed by the Engr-in-Charge

S&F Distribution Board, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 12 way (Concealed flush to wall), 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.

S&F sheet metal enclosures 415 volt TPN 4 way with 200 Amp rated bus bar, double door DB's suitable for provn for a MCB One TPN 63 Amps as incoming and complete all as specified and directed by Engr-in-charge. Note : MCB/RCCB TPN/SPN/SP measured and paid saperatly.

Supply and fixing MCB TPN B Curve, 63 Amps, 415 Volts

M&L for sub main wiring with 4 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl one run of 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 25 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note:- Four run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces

M&L for sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl one run of 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note:- Two run of 6 Sq.mm. and one run of 6 Sq.mm (earth wire) cable incuding one run of conduit pipe will be measured as one length including making good the disturbed surfaces.

Taking down old serviceable storage water heater (Geyser) of any capacity in ltr and refixing after painting and fixing new with two stainless stell flexible pipe for hot and cold water connection including grouting of four Nos fashners with nut,bolts & washers of suitable size as directed in wall and making good in the disturbed surface and match with existing surface complete including all electric and water supply connections.

M&L for Earthing complete with galvanised steel earth plate electrode 60 x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, nnected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate no. 3 connected to Earthing test point all as ecified or indicated including testing on completion( Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover & GI 15 mm dia light grade protection pipe upto 7.5 mtr. lead etc. complete )

Supply, laying testing in trenches LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 35 sqmm 3.5 core all as diredted by Engr - in - charge. Note : Earth work, sand cushioning and cable cover measured and paid separately

M&L for PCC 1:4:8 (nominal mix), type D-2, using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified & directed.

Excvation in trenches not more than 1.5 meter wide and in depth in hard/dense soil all as directed by Engr in Charge

Retuerning and filling of excvated hard soil in trenches all as directed by Engr - in Charge

Removal of surplus hard soil from excavated place and deposting at safe side distance not more than 50 meter from excavated place all as directed

Supply and lay sand for sand cushioning for cable protection in trenches all as directed and specified in SSR Part - 1.Note:. for the purpose of payment punned thickness will be measured.

Supply and laying Un reinforced Precast concrete cable cover, flat class LV type 2 size 300 mm x 180 mm x 40mm all as directed

Supply and fix GI tubing light grade of 40 mm dia for cable protection.

M & L for road cutting(not more than 3.5 mtr in width of road) and excavation upto 60 cm below ground level and laying of 5 running mtr protection 40 mm dia GI pipe of Light grade and make good distrubuted suface by PCC 1:4:8 (nominal mix), type D-2, using 40mm graded crushed stone aggregate complete all as directed

D.K.CONSTRUCTION CO (BID ID -3272695)

M/S KAUTILYA GARG (BID ID -3276673)

mahalaxmi enterprises (BID ID -3272716)

naveen enterprises (BID ID -3272893)