Lift Irrigation Scheme Chountwaliwar (Stage 1st and 2nd)

Stage 1st: Pumping unit: Design, Supply, Installation, Testing & Commissioning of 03 Cusec 118 Mtr Dynamic head Pump motor set with specifications As per Annexure A

SUCTION & DELIVERY PIPE: Fabrication, Providing, Installation, Testing and Commissioning of 250 mm Nominal dia pipe As per Annexure A

Fabrication, Providing, Installation, Testing and Commissioning of 350 mm dia CI foot valve As per Annexure A

Fabrication, Providing, Installation, Testing and Commissioning of 250 mm dia MS long radius bend As per Annexure A

Fabrication, Providing, Installation, Testing and Commissioning of 150 mm Nominal dia. M.S flanged pipe for delivery side including bends, offsets etc. as per specifications given in Annexure A

Fabrication and testing of Tri-Junction as per requirement from 150 mm to 350 mm. As per Annexure A

ALLIED MECHANICAL WORKS: Supply, installation, testing & commissioning of single girder type 03 Tonne capacity fully electrically operated (EOT crane) for inside pumphouse with electrically operated hoist, class II duty, geared travelling trolley with upto 06 meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all three motions electrically operated by suitable rating motor IP 54, control panel & down pendant control block, brake, safety device, cables form motor to starter panel & other required accessories & tested as per Annexure A

Supply, installation, testing & commissioning single girder type HOT crane with geared travelling trolly with upto six meter lift complete with manually operated chain pulley block, long travel rail track (40 mm sq. bar), moving or cross girder, brake, safety device etc. & tested to 50% overload. As per Annexure A

Fabrication providing and fitting of MS working plate fabricated out of the material ISMB/ ISA/ ISC/ISMC 150 x 75x 5.7 mm or as per the direction of site in-charge Engineer. The job include providing and fitting of MS Checkered plate 4m x 1.5 m x 8 mm or as per the directions of Engineer incharge to cover the rectangular structure of the working plate form. The job includes cutting and welding work at site as per site requirement. The job also includes formulation of suitable openings for the passage of suction pipes. The entire steel structure is to be applied with one coat of steel primer and two coats of enamel red oxide of reputed make. As per Annexure A

P /F of Air pressure release valves of suitable size and pressure rating along with allied fittings at suitable spots As per Annexure A

Fabrication, providing and fitting of 350 mm dia. flap valve of pressure rating PN 2.0 As per Annexure A

Fabrication, Providing & Fitting of Angle Iron Operator bed of size 6’ x 6’along with matting for bed and shookproof dielectric rubber floor matting (06 No.). The job includes painting of bed and P/F of matress/cushions as per requirement. As per Annexure A

Fabrication, Providing & Fitting of M.S Trash guard as per site requirement. The trash guard shall be fabricated out of ISMC 75 mm duly fitted with vertical and horizontal iron bars of 10 sqmm size. The minimum gaps between the horizontal and vertical bars shall be 80 mm. The job further includes supporting of the trash guard with additional vertical support as per requirement. As per Annexure A

Painting of Stage 1st MS rising main, suction/delivery pipes, gantry etc. The job includes painting (two or more coats) on pipes and fittings with black anticorrosive bitumasic paint of approved brand over and including a priming coat of ready mixed zinc chromate yellow primer. As per Annexure A

Fabrication, providing and fitting of 350 mm dia. C. I. Swing Type Non Return Valve Flanged End as Per IS : 531 per specification given in Annexure A

Fabrication, providing and fitting of 350 mm dia. expansion joint of pressure rating PN 2.5. The job includes P/F of sundries such as flanges, nut bolts etc. as per site requirement. As per Annexure A

Electrical Components: Design, manufacturing, supply , installation, testing and commissioning of 300 KVA voltage stabilizer. The stabilizer shall be of the following specification and shall comprise of the equipment detailed as per Annexure A

Providing, laying and fitting of 3.5 Core XLPE insulated PVC innersheathed armored LT Aluminum cable 300 sq mm As per Annexure A

Providing and fitting of single core XLPE insulated PVC innersheathed 70 sq-mm armoured LT copper cable As per Annexure A

Providing and fitting of single core XLPE insulated 50 sq-mm and 25 sq-mm armoured LT copper cable As per Annexure A

Electrification of pump house and premises as per details given in Annexure A

Stage 2nd: Pumping unit: Design, Supply, Installation, Testing & Commissioning of 03 Cusec 118 Mtr Dynamic head Pump motor set with specifications As per Annexure B

Rising Main, Suction & Delivery Pipe: Fabrication, providing, laying, installation, testing and commissioning of 350 mm nominal dia. MS Pipe As per Annexure B

Fabrication, Providing, Installation, Testing and Commissioning of 350 mm Nominal dia pipe. As per Annexure B

Fabrication, Providing, Installation, Testing and Commissioning of 450 mm dia CI foot valve of reputed make. As per Annexure B

Fabrication, Providing, Installation, Testing and Commissioning of 350 mm dia MS long radius bend as per below specifications given in Annexure B

Fabrication, Providing, Installation, Testing and Commissioning of 300 mm Nominal dia pipe., As per specifications given in Annexure B

Fabrication and testing of Tri-Junction as per requirement from 300 mm to 350 mm. As per Annexure B

Allied Mechanical Works: Supply ,Installation , Testing and Commissioning of 05 HP Priming pumping unit 75mm x 65mm along with all accessories complete. As per Annexure B

Supply, installation, testing & commissioning of single girder type 03 Tonne capacity fully electrically operated (EOT crane) for inside pumphouse with electrically operated hoist, class II duty, geared travelling trolley with upto 06 meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all three motions electrically operated by suitable rating motor IP 54, control panel & down pendant control block, brake, safety device, cables form motor to starter panel & other required accessories & tested as per IS Specifications given in Annexure B

Supply, installation, testing & commissioning single girder type HOT crane with geared travelling trolly with upto six meter lift complete with manually operated chain pulley block, long travel rail track (40 mm sq. bar), moving or cross girder, brake, safety device etc. & tested to 50% overload. As per Annexure B

Fabrication providing and fitting of MS working plate fabricated out of the material ISMB/ ISA/ ISC/ISMC 150 x 75x 5.7 mm or as per the direction of site in-charge Engineer. The job include providing and fitting of MS Checkered plate 4m x 1.5 m x 8 mm or as per the directions of Engineer incharge to cover the rectangular structure of the working plate form. The job includes cutting and welding work at site as per site requirement. The job also includes formulation of suitable openings for the passage of suction pipes. The entire steel structure is to be applied with one coat of steel primer and two coats of enamel red oxide of reputed make. As per Annexure B

Fabrication, providing and fitting of 300 mm dia. C.I. Rising Spindle Sluice Valve Flanged End as Per IS : 14846, as per specification given in Annexure B

Fabrication, providing and fitting of 300 mm dia. C. I. Swing Type Non Return Valve Flanged End as Per IS : 5312, as per specification given in Annexure B

Fabrication, providing and fitting of 350 mm dia. expansion joint As per Annexure B

Fabrication, providing and fitting of 350 mm dia. flap valve of pressure rating PN 2.5 As per Annexure B

Fabrication, providing and fitting of 350 mm dia. C. I. Swing Type Non Return Valve Flanged End as Per IS : 5312, As per Annexure B

P /F of Air pressure release valves of suitable size and pressure rating. As per Annexure B

Fabrication, Providing & Fitting of Angle Iron Operator bed of size 6’ x 6’along with matting for bed and shookproof dielectric rubber floor matting (06 No.). The job includes painting of bed and P/F of matress/cushions as per requirement. As per Annexure B

Fabrication, Providing & Fitting of M.S Trash guard as per site requirement. The trash guard shall be fabricated out of ISMC 75 mm duly fitted with vertical and horizontal iron bars of 10 sqmm size. The minimum gaps between the horizontal and vertical bars shall be 80 mm. The job further includes supporting of the trash guard with additional vertical support as per requirement. As per Annexure B

Painting of M.S rising main, suction/delivery pipes, gantry etc. The job includes painting (two or more coats) on pipes and fittings with black anticorrosive bitumasic paint of approved brand over and including a priming coat of ready mixed zinc chromate yellow primer. As per Annexure B

Electrical Component: Design, manufacturing, supply , installation, testing and commissioning of 300 KVA voltage stabilizer. The stabilizer shall be of the following specification and shall comprise of the equipment detailed in Annexure B

Supply, installation, testing & commissioning of 275 HP 415 V Fully automatic Microprocessor based soft starter with built in bypass arrangement for pump control application as per general specification given in Annexure B

Providing, laying and fitting of 3.5 Core XLPE insulated PVC innersheathed armored LT Aluminum cable 300 sq mm for main service line from transformer to LT Panel. The job includes P/F of sundries such as thimbles etc. as per site requirement. As per Annexure B

Providing and fitting of single core XLPE insulated PVC innersheathed 70 sq-mm armoured LT copper cable from panel to voltage stabilizers. The job includes P/F of sundries such as thimbles etc. as per site requirement. As per Annexure B

Providing and fitting of single core XLPE insulated 50 sq-mm and 25 sq-mm armoured LT copper cable for motors , starters as service line: a) 50 sq-mm= 225 Mtr. b) 25 sq-mm = 75 Mtr. The job includes P/F of sundries such as thimbles etc. as per site requirement. The job includes earthing of the electrical equipments. As per Annexure B

Electrification of pump house and premises as per details as under: As per Annexure B

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil :

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil :

Extra for every additional lift of 1.5 m or part thereof in excavation/banking excavated or stacked material : All kinds of soil :

Providing & laying of stones/stone solling in horizontal on level incld cost of stones.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete:

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platforms.

Columns, pillars, piers, abutments, posts and struts.

Edges of slabs and breaks in floors and walls Under 20 cm wide

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work:

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Second class kail wood 35mm thick)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows 4 mm thick glass pane (weighing not less than 10 kg/sqm)

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia wire and 1.4 mm wide aperture with matching wood beading

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. . (0.63 mm thick with zinc coating not less than 275 gram/m2)

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gram/m2

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shades, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Size of tile 500x500 mm)

Provision for Hinges/Towerbolts/Handles/Hooks and like items required for 02 No. buildings including washrooms etc as per the drawings. Rate to be Quoted (RTQ)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying of Precast RCC Rings of for Construction of Septic Tank circular in plan using 1 feet high and 4feet dia.RCC rings including earthwork excavation and Exacavated earth to be leveled beyond the cutting edges.all complte job.

P/F Sanitary/ Water Supply Items including carriage, taxes, testing And commissioning all complete job.

P/F of squatting pan Orissa (580x440mm)

Wash basin (630x450mm)

PVC flushing cistern low level (10 Ltr.)

100mm PTMT grating for gully

100mm PVC Waste Pipe

75mm PVC Waste Pipe

100mm PVC P/S Trap

75mm PVC P/S Trap

100mm PVC Bend, T

75mm PVC Bend

Gate Valve (Gun metal)

Bright Polished Brass Mixer Tap

Ball cock for Water Storage Tank

Geyser (50 Ltr.) Venus Made

P/F of 600x450mm bevelled edge mirror of superior glass (Of approved quality) complete with 6mm thick board.

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing Chlorinated Poly vinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings I/C fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. (Concealed work including cutting chases and making good the walls etc.)

(i) 15mm (Concealed Work)

(ii) 20mm (External work)

Bright Polished Stop Cock

Bright Polished Towel Rail

Semi Rigid PVC waste pipe for sink and wash basin 40 mm dia with length not less than 700 mm i/c PVC waste fittings

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete(150 mm).

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing of ornamental gate 4.5 metre wide and 2.10 m high ornamentsl gate including 150mm 2mm thick side posts including locking arrangements all complete including two coatings of iron primer and paintint as per the directions of Engineer Incharge

Providing and fixing G.I. chain link fabric fencing of required width inmesh size 50x50 mm including strengthening with 2 mm dia wire or nuts,bolts and washers as required complete as per the direction of Engineer-incharge. Made of G.I. wire of dia 4 mm.

Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade. New Steel work (two or more coats)

Privisiong and fixing of 100mm dia weep holes (R/s)

Carriage of different materials by Mechanical Transport including loading ,unloading and stacking from different sources upto road side of work.

20 mm aggregate

40 mm aggregate

Stone soling

Cement/Steel

Bricks

Carriage of different materials by manual labour including loading ,unloading and stacking at actual site of work

20 mm aggregate

40 mm aggregate

Stone soling