MIRPA Side Protection work and revamping of Vellanoor Lift Irrigation Scheme in Chathamangalam Panchayath Kozhikode Dist

Amount

side protection works

60.2.2 : Bailing out water Using 5HP Pump- Bailing out water with 5HP engine and pump set including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete

2.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

60.1.2 : RING BUND Type II Putting up ring bund with earth fille gunny bags of top width 1.0m bottom width 2.0m height 2.0 m side and filling in between with earth to form ring bund and maintaining the same leak proof till the completion of the work and clearing the site by dismantling the bund after completion of the work.etc.complete.

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

60.64.1 : Coconut Pile - Supplying and stacking well matured straight coconut post for driving down throug various strata bellow bed level including cost coveyance labour charges etc complete.

60.64.4 : Coconut Pile - Driving down coconut pile to lines and levels through variuos strata including all hire charges and labour for fixing , staging platform and all other appliances necessary for pile driving down after pointing the bottom end

60.7.4 : DR PACKING FOR APRONS - Rough stone dry packing for apron with good quality blasted rubble including packing to compactness to lines levels, cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

4.3.1 : Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

4.3.2 : Centering and shuttering including strutting, propping etc. and removal of form work for:Retaining walls, return walls, (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.5 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

5.1.3 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

60.7.1 : DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.26.1 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

15.12.1 : Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

10.11.1 : Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side/top/centre hung, with beading and all members such as F7D, F4B, K11B and K 12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 ( 1 Cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

Annual maintenance of existing 30 HP centrifugal pumps

od28586/2020_2021/MH : Dismantling the 25/30HP motor into stator and rotor, cleaning the windings attending minor repairs, re taping the coils if necessary, varnishing the coils with best quality insulation varnish, cleaning and greasing the bearings with good quality grease, heating the windings, reassembling, test running including scrapping, cleaning and painting with enamel paint.

od28587/2020_2021/MH : Fully Comprehensive Annual Maintenance of 25/30 HP pump set for a period of 12 months including attending all repairs, reconditioning the damaged parts , replacing spares with original make as per sample , renewal of gland packing , gasket packing , rubber packing , greasing the bearing, changing bearings of pump,reconditioning pump shaft etc as and when required including overhauling of pump and maintain the motor pump sets , starter in good working condition all time during the period of contract and the faults should be rectified with in the time allowed and as directed by the departmental officers at site (cost of material,labor,conveyance charges all includes).

od28588/2020_2021/MH : Fully Comprehensive Annual Maintenance of 3/5 HP mono block vacuum pump for a period of 12 months including attending all repairs, reconditioning the damaged parts , replacing spares with original make as per sample , renewal of gland packing , gasket packing , rubber packing , greasing the bearing, changing bearings of pump,reconditioning pump shaft etc as and when required including overhauling of pump and maintain the motor pump sets , starter in good working condition all time during the period of contract and the faults should be rectified with in the time allowed and as directed by the departmental officers at site (cost of material,labor,conveyance charges all includes).

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

od25888/2020_2021/MH : Supply and fixing of SS Strainer 250 mm at suction side of existing line after dismantling including all materials and labour charges etc, as per the direction of the department officer at site

od25886/2020_2021/MH : Testing of Pump and conducting Trial run.

Erection of New pump (which is to be purchased through MLA fund) and thier Pipe Line Work

od28566/2020_2021/MH : Erection of 30HP pump with Motor in correct alignment after leading them from outside of pump house to the respective foundations including cost of labour, hire charge of equipment, tools and plats etc. complete.

18.72.18 : Providing and laying S & S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329:250 mm dia Ductile Iron Class K - 9 pipes

18.72.19 : Providing and laying S & S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329:300 mm dia Ductile iron Class K-9 pipes

od28571/2020_2021/MH : Cutting 300 mm DI pipe diametrically by abrasive cut of saw ,the cut being perpendicular to the axis of pipe and smoothing of the cut end for fixing additional flanges .

od28572/2020_2021/MH : Cutting 250 mm DI pipe diametrically by abrasive cut of saw ,the cut being perpendicular to the axis of pipe and smoothing of the cut end for fixing additional flanges .

od28573/2020_2021/MH : Fabricating and Fixing MS flanges for connecting pipe lines to bends, reducers etc. including cost of material, labour , machinery, conveyance, painting, incidental and handling charges etc complete. (250 mm pipe)

od28574/2020_2021/MH : Fabricating and Fixing MS flanges for connecting pipe lines to bends, reducers etc. including cost of material, labour , machinery, conveyance, incidental and handling charges etc complete(300NB pipe).

18.66.1 : Providing and laying S&S.C.I Standard specials such as tees, bends, collars tapers and caps etc., suitable for flanged jointing as per IS: 1538:UPto 300 mm dia

18.30.6 : Providing flanged joints to double flanged C.I./ D.I pipes and specials, including testing of joints:250 mm diameter pipe

18.30.7 : Providing flanged joints to double flanged C.I./ D.I pipes and specials, including testing of joints:300 mm diameter pipe

od28646/2020_2021/MH : Supply and fitting of SS Strainer at suction side of pipe (NB 300 MM) including all materials and labour charges for new line as per the direction of the department officer at site

18.31.5.2 : Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately):250 mm diameterClass II

18.12.3 : Providing and fixing G.I. pipes complete with G.I fittings including trenching and refilling etc. External work25 mm dia nominal bore

18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

od28637/2020_2021/MH : Commissioning of the pumps and motor and trial running as per the direction of the departmental officers at site including materials labour and conveyance

Bidder Name

L&A INFRAZ DEVELOPERS LLP