REPAIR REWINDING AND MAINTENANCE OF SUMMER APPLIANCES INCLUDING REPLACEMENT OF WORN OUT ACCESSORIES OF CEILLING FAN EXHAUST FAN PEDESTAL FAN AIR CIRCULATOR AND GEYSER AND REPAIR REPLACEMENT AND MAINTENANCE OF B VEHICLES AND CONNECTED ACCESORIES O

Amount

Schedule'A' Part-I: E&M works

LIST OF WORKS PERTAINING TO SUMMER APPLIANCES

Taking down unserviceable ceiling fans, exhaust fans, wall mounting fans, wall mounting fans, pedestal fan/table fan any sweep and size from its location by disconnecting and sealing all electrical lines for inspection of serviceability for annual painting/maintenance/servicing by oiling, greasing replacement of condenser, ball bearing/bushes as required at site of the fan and including spray painting with one coat of synthetic enamel paint of approved colour and keep take site of u/s fan for carried out repair at workshop and refixing/ reconnected the same as its original place connecting all electrical connection with existing size twin twisted copper conductor cable from ceiling rose/connector to fan and testing complete all as specified and directed. (NOTE (a) New parts i.e. condensor ball bearing/bushes/new flexible wire shall be measured and paid separately under "Supply only" rates here-in-after. (b) Minor parts, if any, not mentioned in the schedule but required for smooth functioning of fans are deemed to be included in the rate of the item.)

Taking out burnt winding from the under mentioned fans of any sweep, make and size, cleaning of slots, providing new insulation within slots and winding with new super enamelled copper wire of suitable gauge not less than the weight mentioned under concerned items including heat varnishing, backing and testing complete all as specified and directed.

(a) Ceiling fan of 1400mm sweep (Super enamelled copper wire not less than 420gm)

(b) Ceiling fan of 1200mm sweep (Super enamelled copper wire not less than 380gm)

(c) Exhaust fan of 380mm sweep (Super enamelled copper wire not less than 320gm)

(d) Exhaust fan of 300mm sweep (Super enamelled copper wire not less than 280gm)

(e) Air circulator fan of 400mm sweep (Super enamelled copper wire not less than 550gm)

(f) Air circulator fan of 610mm sweep (Super enamelled copper wire not less than 950gm)

(g) Pedestal fan of 400 mm sweep (Super enamelled copper wire not less than 350gm)

(h) Table fan of 300 mm sweep (Super enamelled copper wire not less than 280gm)

Supply only ball bearing of the following sizes : (Make : SKF/NBC)

Supply only gun metal bush of appropriate sizes.

Supply only condenser 2.5 mfd

Supply condenser clamp.

Supply only PVC ceiling fan canopy (set of two). (Make : Usha/Bajaj/Orient)

Supply only rubber bush for ceiling fan.

Supply only ceiling fan hanging clamp made of mild steel sheet with bolts, nuts, washers and safety pin.

Supply only pedestal fan canopy.

Supply only PVC insulated multistranded copper conductor flexible twin core of size 40/0.0076

(a) M&L for painting of ceiling fan 1200/1400mm sweep complete with blade and down rod after rewinding the motor with one coats of synthetic enamel paint, white, by spraying including filling cavities with filler after scrubbing down all paying using emery paper, claiming washing etc. and writing MES No. complete all as specified and directed.

(b)All as per item No 12 above but exhaust fan 380/300mm sweep complete with blade & bracket etc.

(c) All as per item No 12 as above but wall mounting/pedestal fan/table fan complete with blade and jalli frame etc complete

(d) All as per item No 12 as above but air circulator fan of 400/610mm sweep complete with blade, bracket & Jalli etc.

Supply only three pin top 15 Amp AC 230V. Make : Anchor/Key

M&L for fixing of exhaust fan/air circular fan in existing wall with provide suitable size of fastener to held the fan complete all as directed by Engr-in-charge.

Taking down unserviceable geysers of any capacity and make from each location by disconnecting and sealing all electrical and water lines for annual maintenance/servicing. Overhauling, dismantling the same for repair/replacement of unserviceable parts, including brazing to inner tank, cleaning, taking out sludge from inner tank and washing with cleaning solution and reassembling and refixing the same in each original location/ position, connecting all electrical and water connections including provn of 2.5 Sqmm 3 core sheathed multi-stranded copper conductor flexible cable from connector block to geyser and testing complete all as specified and directed. (NOTE (a) New parts shall be measured and paid separately under "Supply only" rates here-in-after. (b) Minor parts, if any, not mentioned in the schedule but required for smooth functioning of geysers are deemed to be included in the rate of the item.)

Supply only PVC inlet pipe, 15mm bore, 450 long including both end check /end nuts and washers. Make : Prayag/ Royal/ Puspa.

Supply only PVC steel braided outlet connection pipe, 15mm bore, 450 mm long including both ends check nut & washer complete.

Supply only heating element of any type 1500 Watts. (Make : Bajaj/Racold/Venus)

Supply only heating element of any type 2000 Watts. (Make : Bajaj/Racold/Venus)

Supply only thermostat of any type suitable for 50/35/25 ltrs capacity geyser.

Supply only internal assembly complete with packing ring, bolts, nuts & washers suitable for 50/35/25 ltrs capacity geyser.

Supply only thermal cut off ISI marked suitable for 50/35/25 ltrs capacity geyser.

Supply only fusible plug made of brass having lead alloy fuse suitable for 50/35/25 ltrs capacity geyser.

M & L for painting geyser of capacity 50/35/25 ltrs complete, in situ, with two coats of synthetic enamel paint, white, by spraying including filling cavities with filler, denting after scrubbing down old paint using emery paper, cleaning, washing etc. and writing MES No complete all as specified and directed.

LIST OF WORKS PERTAINING TO Veh BA No - 05C-075991A (TATA-207)

Dismantling and taking down the gear box assembly of the veh (Tata 207), cleaning of all parts and repair the same by replacement of the following unserviceable parts incl testing after completion of work.

(a) Clutch cable - 02 Nos

(b) Brake oil

(c) Gear liver kit -

(d) Clutch pressure kit

(e) Release bearing

(f) Clutch frog

(g) End bearing

(h) Oil seal

Dismantling and taking down broken propeller shaft along with universal joint and repair the same by welding and grinding on lath machine incl replacement of universal joint -01 No and testing complete after completion of works.

Dismantling the shock absorber and taking out of shock absorber bush from left and right side of the wheel and repair the same by replacement of absorber bush -02 Nos, brush -04 Nos and testing complete after completion of works.

Material and labour for fabricating rear seat base of size 200cm x 60 cm - 02 Nos. Replacing foam of size 2 inches thick with good quality of rexin cover including good quality cotton cloth stitched as per size with adjusting string complete as directed.

Dismantling and taking out of the ECM (Electronic Circuit Mechanism box) segregating for unserviceable parts and repair by replacement of electronic circuit, diodes, transistors, electronic relay-02 Nos etc and testing the same after complete of works.

Material and labour for repair of doors by replacement of front door lock-02 Nos and rear door lock -02 Nos.

Dismantling of broken leaf spring, U clamp and repair the same by replacement of main leaf spring, U clamp, nuts & bolts and washers.

Servicing of complete vehicle by cleaning washing and greasing all parts of veh incl replacement of engine oil and following unserviceable parts.

(a) Clutch cable

(b) Hand Brake cable

(c) Timing bearing

(d) Looking mirror right and left

(e) Brake oil Container

(f) Cap of coolant box-02 No

(g) Radiator hose pipe -02No

(h) Accelerator cable - 02 No

(i) Centre bearing bush - 02 No

(j) Speedometer cable with gear assembly -02 No

M & L for making good the disturb surface of veh by cutting, denting and welding of damage/rusted parts of vehicle and painting complete veh with two coat of synthetic enamel paint over one coat of red oxide primer and making all symbol, BA No etc all as directed by Engr-in-Charge.

LIST OF WORKS PERTAINING TO Veh BA No - 04D - 160803P & 01D-142458A (Eicher -02 Nos)

Dismantling/opening and taking out eicher engine head and carry out the repair by replacement of following unserviceable part and testing the same after completion of works.

(a) New piston ring set - 02 Nos

(b) Tappet cover gasket - 02 Nos

(c) Oil sump cover gasket - 02 Nos

(d) Cylinder head gasket - 02 Nos

(e) Valve guide - 02 Nos

(f) Engine foundation pad -08 Nos

Servicing of complete vehicle by cleaning washing and greasing all parts of veh incl replacement of engine oil and following unserviceable parts :-

(a) Break oil container - 02 Nos

(b) Cap of coolant box - 02 Nos

(c) Radiator hose pipe - 02 Nos

(d) Accelerator cable - 02 Nos

(e) Centre bearing bush - 02 Nos

(f) Clutch cable - 02 Nos

(g) Brake oil

Material and labour for repair of door by replacement of front door lock - 02 Nos and rear door lock - 02 Nos and testing after proper locking

Dismantling of broken leaf spring , U clamp and material & replacement of main leaf spring after giving proper tension and new U clamp, nuts & bolts and washers.

Dismantling / opening and taking down rear differential box and repair the same by replacement of the mirror parts also changing the differential oil complete & broken teeth of transmitting shaft.

Dismantling / opening and taking down of fuel tank and refixing the same after cleaning, washing the fuel tank by using dissolve bio-film in diesel fuel tank.

Material and labour for fabricating front driver seat base of size 40cm x 50 cm and co-driver seat base of size 90 cm x 50 cm. Replacing foam of size 2 inches thick with good quality of rexin cover including good quality cotton cloth stitched as per size with adjusting string complete as directed.

Material and labour for fabricating back rest of driver seat base of size 40 cm x 50 cm and co-driver seat of size 90 cm x 50 cm replacing foam of size 2 inches thick with good quality of rexin cover including good quality cotton cloth stitched as per size with adjusting string complete as directed.

Dismantling / opening and taking out of old tarpaulin cover veh and replacing with heavy duty water proof tarpaulin cloth black colour of size 4.3 x 4 mtr over main body, 2 mtr x 1 mtr of front screen with one window of size of 80cm x 30cm having flag over window portion and 2mtr x 2mtr at back screen with one window of size 80cm x 30 cm having flap over window with velvet in required length. The side portion of tarpaulin will have 4 window of size 45cm x 30cm two each in each side including flap over the window portion. tightening the complete set of tarpaulin as per Eicher body with 12mm dia nylon rope of required length in all around the complete vehicle.

Dismantling the shock absorber and taking out shock absorber bush from left and right side of the wheel and repair the same by replacement of absorber bush -02 Nos, brush-04 Nos and testing complete after completion of works.

Dismantling and taking down the gear box assembly of the (Eicher), cleaning and greasing of all parts and repair the same by replacement the clutch disc assembly with clutch release bearing& cylinder kit sleeve.

Opening of lub oil filters, fuel filters, by pass filter and supply & fixing main lub oil filter with body (complete kit of main lub oil fiter-01No), fuel filter set - 01 No and by pass filter set - 01 No.

Dismantling / taking down of FIP and send to civil work shop for calibration of FIP by adjustment of nozzle timing etc and replacing the nozzles-06 Nos & delivery valve-06Nos bearing -02 Nos element-04Nos component kit-01 No.

Dismantling / opening and taking down of old rusted seat frame and material and labour for making New frame of seat in rear side of vehicle made out of angle iron size of 40cm x 40cm x 05mm of length 2mtr and with 0.45mtr -04 Nos for rest seat including 45cm long GI pipe 25mm dia light grade 2 Nos for each seat including folding arrangement and back side seat 04 Nos of same size and shape directly fixed with body with nuts, bolts and washers including welding work including coat of red oxide and two coat of synthetic enamelled blue paint and all 08 Nos seats are fabricating with same length of foam 50mm thickness, covered with good quality of rexin cover fixed on same length of wooden planks of second class hard wood of 25mm thickness with screws complete all as directed.

Dismantling/opening and taking down of all rusted step frame and material and labour for making new frame for steps on tail board of vehicle made out of angle iron of size 40mm x 40mm x 5mm of length of 50 cm as directed.

M & L for making good the disturb surface of veh by cutting, denting and welding of damage / rusted parts of vehicle and painting complete vehicle with two coat of synthetic enamel paint over one of red oxide primer and making all symbol, BA No etc all as directed by Engr-in-Charge.

LIST OF WORKS PERTAINING TO Veh BA No - 00A-51039L (Royal Enfield)

Dismantling/opening and talking out Royal Enfield of front and rear wheel including all accessories segregating unserviceable parts and replaced with the set of brake shoes, spring etc complete and testing after completion of work.

Checking all electrical, mechanical assy and other parts of veh and segregating unserviceable parts, carryout repair work by replacement of following unserviceable parts incl testing after completion of of work :-

(a) Clutch Plate

(b) Indicator bulb

( c) CB point

(d) Handle grip

(e) Kick Paddle rubber

(f) Ignition switch

(g) S T Coil

(h) Kilometre pinion

(i) Rectifier

Complete servicing,washing,cleaning and greasing all parts of Motor cycle including replacement of engine oil. (Note engine oil will be measure and paid separately)

Dismantling / opening and taking out of front and rear wheel with all accessories segregating unserviceable parts, carryout repair work by replacement of following unserviceable parts and testing after completion of work :-

(a) Brake shoes - 2 Sets

(b) Springs - 2 Sets

(c) Shock absorber - 2 Sets

Checking of complete electrical and mechanical system and carry out repair including replacement of following UNSV parts:-

(a) Foot guard pad - 2

(b) Ignition switch - 2

(c) Ampere meter - 2

(d) Fuel tank cap - 2

(e) Indicator assembly - 2

(f) Head light bulb - 2

(g) Kick spring - 2

(h) Petrol over flow pipe - 2

(i) Spark plug - 2

M/S NIYATI NETWORK

M/S SANKAR GOPE

M/S PAUL ENTERPRISE

SHRI RAJESH DEY