PROVN OF 01 X WEREHOUSE WITH ENVIRONMENT CONTROLLER FOR HOUSING OF PAYLOADS OF HERON MK -II (SATCOM)

Amount

Surface dressing in soft loose soil n exc 15 cm deep and getting out, complete all as specified and directed.

Excavating in trenches n.exe. 1.5 m width and n.exe. 1.5 m in depth for foundation in soft/loose soil & getting out, complete all as specified and directed.

Excavating in trenches exe. 1.5 m width and exc 1.50 m but not exe. 3.00 m in depth for foundation in soft/loose soil & getting out, complete all as specified and directed.

Returning filling in, including spreading, levelling, watering & well ramming in layers not exc 25 cm, complete all as specified and directed.

Removing excavated material n exc 50 m & depositing where directed at a level n exc 1.5 m ,complete all as specified and directed.

M&L cement concrete with PCC type D2 1:4:8 using 40mm graded aggregate as in foundation ,complete all as specified and directed.

M&L for M25 RCC design mix using 20 mm graded aggrgate for raft foundation footing ,bases of columns, plinth beams & mass concrete, complete all as specified and directed.

M&L for M25 RCC design mix using 20 mm graded aggregate for columns, pillars,posts and struts, complete all as specified and directed.

M&L for M25 RCC design mix using 20 mm graded aggregate for beams, cantilevers, roof beam , lintels over 1.5 m span, etc, complete all as specified and directed.

M&L for M25 RCC design mix using 20 mm graded aggregate for slab complete all as specified and directed.

M&L for M25 RCC design mix using 20 mm graded aggregate for chajjas , etc, complete all as specified and directed.

M&L for precast reinforced cement concrete cover slab Type B1 (1:2:4) ( using 20mm graded aggregate) as in drain cover, manhole cover, etc, complete all as specified and directed.

M & L for TMT reinforcement 10 mm dia and over cut to length bent to shape including cranking, hooking etcbinding with mild steel wire not less than 0.90 mm dia (annealed) all as directed complete.

S & F mild steel TMT bar 5 mm dia and over upto and including 10mm dia in strrups as in including cutting, bending and binding with mild steel not less than 0.9 mm dia (annealed) all as directed complete.

Form work for foundation footing , bases of columns & plinth beams similar work vertical or batter all as directed complete..

Form work for side of pillars, posts, columns & similar works vertical or batter,all as directed complete..

Form work to side & soffits of floor or roof beams, slab, lintels & similar works , all as directed complete.

Form work to soffits of roof slab & similar works ,all as directed complete..

M&L for brick work with burnt old size bricks built in cement mortar 1:6 straight or curved on plan exceeding 6mtr mean radius and all as directed.

M&L for 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) mixed with WPC ( WPC shall be measured & paid separately

M&L rendering 15mm thick on other than fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and smooth.

M&L rendering 15mm thick on fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and smooth using extra cement, all as directed complete.

M&L for 20mm thick plaster on fair faces of brick work or concrete surface in cm (1:4) with wpc @2% by weight face of conc work to wall surface and the surface is finished even and smooth without using extra cement

Supply only integral WPC

M&L for rendering 5 mm thick on ceiling or concrete Surfaces in cement mortar 1:3 finished even and smooth ,all as directed complete..

M&L for 75 mm thick PCC 1:3:6 type C2 using 40mm graded aggregate as in plinth course as directed by Engineer in charge.

M&L Sand filling under floors or in foundations including watering and conosoldiation, all as directed complete..

M&L for brocken stone or boulders of hardcore of gauge n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface.

M&L for 100mm thick PCC type D2 1:4:8 using (40mm gradded aggregate) as in sub base, all as directed complete..

M&L for Pre-polished Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and poined in neat cement slurry with grey cement and pigment in floors including 20 mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over 20 mm thick screed bed in C:M 1:6, laid and jointed with grey cement slurry mixed with pigment to match the mixed with pigment to match the shade of the slab including rubbing and polishing , complete all as specified and directed.

M&L for Machine cut kota stone slab as in skirting 20-25mm thick over 10 mm thick backing coat in C:M 1:4, laid and jointed with grey cement slurry mixed with pigment to match the mixed with pigment to match the shade of the slab including rubbing and polishing , complete all as specified and directed.

S&F facroty made Second class hard wood kiln seasoned and chemically pressure treated plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints, all as directed complete..

S&F 35 mm thick factory made second class hard wood, kiln seasoned and chemically pressure treated plain framed, panelled shutter (Two panel) with lock rail and panel of 9 mm BWP Commercial ply or 12 mm veneered particle board with commercial face veneers on both faces or 10 mm bison panel, all as directed complete..

S&F for anodised Aluminium two track sliding window and ventiletor frame made up 62 mm /29.5 mm 1.5 mm thick aluminium section & shutter made up 38 mm / 20 mm/1.5 mm thick without sash bar alum section including all necessary joining cleats,hold fast ,rubber gasket anodised snap beading,anodised alumn fittings,suitable alumn handle and locking arrangment etc as directed.

S&F 4 mm thick Sheet glass, ordinary quality and glazing with aluminium beads in squares exceeding 0.50 Sqm in each pane,all as directed complete.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or revited, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confirming to Fe.290. Gde-E-165, all as directed complete.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section, all as directed complete.

S&F aluminium alloy 250mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy and fixed.

S&F 100mm MS butt hinges medium weight

S&F aluminium handle cast type anodised 150mm size

M&L three coat of white wash on ceiling surface including preparation of new surface complete all as specified and directed.

M&L for applying a coat of 1mm thick wall care putty over plaster surface to prepare the surface even and smooth as per manufacture instruction, complete all as specified and as directed.

M&L for preparation of new plastered wall surface applying two coat of oil bound distemper on wall all as complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces ,all as directed complete..

M&L for brushing neat cement slurry with 03 Kg of cement per Sqm, all as directed complete.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 . (Internal water proof compound measured seperately)

M&L 25 mm thick cement concrete PCC Type B0 1:2:4 using 12.5 mm graded aggregate.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application including coating the surface with water based bituminous primer blow bitumen of 85/25 or 90/15 at 1.2 Kg/Sqm both at bottom and top of the membrance and finally finished with one coat of bitumenous aluminium paint at 100 gm per sqm complete all as specified.

M&L for preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of primer of any description, not otherwise described, over 10cm width or girth, complete all as specified and directed.

M&L Painting two coats of synthetic enamel paint over a coat of red oxide primer to new steel Surfaces of any description, not otherwise described, over 10cm width or girth complete all as specified and directed.

M & L Submain wiring with 2 runs of single core 6 sqmm PVC insulated unsheated (FRLSH) multistranded 1100 volts grade with copper conductor duly cutting chases on walls and drawn through and including non-metalic Rigid PVC Conduit ISI marked and its accessories including one run of single core 6.0 sqmm PVC insulated unsheated multistranded 1100 volts grade with copper conductor cable as earth continuty conductor along with the wiring and connected from DB to DB/main board with proper copper lugs and making good disturbed surfaces and matching with existing colour complete all as specified and directed.

S & F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified. Make- L&T/Schneider / Legrand / Seimens

S & F MCB Double Pole 32 Amps 240/415 Volt, confirms to IS/IEC 60898 Breaking Capacity of 10 kA, C-curve, complete all as specified and directed.Make- L&T/Schneider / Legrand / Seimens

Supply and fixing for single pole and neutral enclosure with a two pin and earth plug and socket complete with on one single pole MCB 20 Amp, 240 volts . Make- L&T/Schneider / Legrand / Seimens

S & F MCB SP 6 to 32 Amps AC upto 240 volts for fixing on MCB DB's all as specified. Make- L&T/Schneider / Legrand / Seimens

Supply and install split units indoor/outdoor complete with cordless remote control with minimum 5 star rating inverter type of capacity 2.0TR , copper condensor coil including 4 sqmm 4 core flex cable connection from indoor to outdoor unit as per site requirement including necessary masonry work for making good distrubuted surface and match with the existing colour complete all as specified. Make : Voltas/ Carrier / Daikin / Hitachil

Supply and Installation, commissioning of Industrial dehumidifier electric driven single phase indoor unit Max. power consumption 990W,Extraction (30 ºC/80% RH) 85 ltrs / 24 hr, with coverage Volume 9000 Cu feet , Air circulation rate 700M³ / Hour ,Working temperature range +5 C to +35 C and confirming to IS-1391 Para II 1992 herimatically sealed rotary air compressor working with Non CFC refrigerent complete all as specified and directed. Model -O85 of make-Origin/SAMSUNG/VOLTAS / Bry-Air

Supply and fix voltage stablizer for automatic operation, single phase naturally air cooled indoor type wall mounted and designed for input variation between 130 volts to 300 volts with out put voltage stablized at 230 volts with accuracy of + 2.5% and capacity 5 KVA suitable for AC complete all as specified. MAKE- V guard/Microtek/Luminious.

M&L Point Wiring with 1.5 Sqmm Copper Conductor single core PVC insulated Flame Retardant Low Smoke (FRLSH) Unsheathed 1100 Volt grade multi-stranded Cable drawn through and including PVC Casing and Caping medium grade of suitable size and its Accessories as required at Site, fixing on surface of Wall, Roof, mounted on Sunk Mild Steel Pressed Terminal Box 1.22mm thick of suitable size duly painted with red oxide metal primer with 3.0mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, etc. including PVC insulated and unsheathed Single Core multi-stranded Copper Conductor Cable of size 1.5 Sqmm (FRLSH) Green in Colour as Earth Continuity Conductor connected to Common Earth and Earth dolly for One Light Point controlled by One 1-Way Switch 5 Amp, complete all as specified and as directed.

Description all as per item No 60 here in before but for one 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

Description all as per item No 60 here in before but for one 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board .

Description all as here in before but using 2.5 sq mm single core copper conductor cable of multistranded flame retardant Low smoke (FRLSH) PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point incl running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F Switch piano (White) flush type single pole one way 5 Amp, 230 Volts complete all as specified.

S & F Socket outlet (White) 2 in 1, 5/6 pin, 5 Amps complete all as specified and directed.

S & F Switch socket combination (White) flush type multipurpose 5/6 pin 5 Amps two in one , 230 volts complete all as specified.

S&F Switch socket combination (White) 2 in 1 5/6 pin, 15 Amp flush type universal. complete all as specified.

S & F Lamp holder (White) with insulated body, with back plate suitable for batten fittings complete all as directed.

S & F sheet metal enclosure MCB VTPN 8 way Double door IP 43 Protection Ready to use DBs - Provided with insulated vertical phase bus-bars |neutral bar/s with shroud/s | earth bar/s | sticking saddles | cement spill protector | color-coded interconnecting wire set | cable ties | blanking plates and circuit identification labels With provision for 4 Pole MCCB 200 A as incomer and SP/SPN MCBs as outgoing complete all as specified and directed.Make- L&T/Schneider / Legrand / Seimens

S & F MCCB 4 Pole 415 volts 160 Amps with breaking capacity 25 KA suitable for fixing in item No. 24 complete all as specified.Make- L&T/Schneider / Legrand / Seimens

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative ultra slim round profile LED lighting fixture with extruded polycarbonate , environmental friendly energy efficiebt ready to use pack with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make :- Model No. LHEXAPP7UN1W020 of Havells or Equivalent in Surya / Crompton / Philips

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 20 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape duly fixed with Clamps nuts and bolts complete all as directed by Engineer-in-Charge. Make- Havells Cat Part No. LHEXAYP7PN6K020 or equivalent in /CG/Surya / Philips

M & L sand cushioning in trenches for cable protection with coarse sand laid dry in trenches with uniform thickness including consolidation complete all as directed.

Supply & Laying well burnt brick , locally available best quality (sub class "B" bricks ) laid in trences perpendicular to UG Cable protection complete all as specified.

Supply & Laying XLPE LT heavy duty UG Cable of size 50 Sqmm 3.5 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary aluminium lugs after cutting to required length complete all as specified and directed. Make :- Polycab and equivalent in Havells /RR Kabel / KEI/Gloster

S & F GI Tubing light grade of size 50mm dia in protection of cable at road crossing /hard standing/pole protection fixed with clam as per site requirement etc all as specified and directed.

Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 40mm bore (dia) for passing of UG Cable, complete all as specified and as directed. NOTE: GI Pipe laid will be measured and paid separately under appropriate Item.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground to a depth not less than 2.25 mtrs below ground level with top edge of earth plate not less than 1.5 mtrs below normal ground level connected to GI earth wire 4 mm dia drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, check nuts and washers including excavation earth work provisioning of PCC chamber made of PCC 1:3:6 RCC cover funnel with wiremesh 20mm dia watering pipe Medium grade, GI protection pipe 20mm dia bore all as specified in Electrical Plate No.3 of SSR Part I.

S & F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified.Make Havells, Cat No: LHLDEUEBML8Z010 or equivalent in Crompton or Bajaj

Supply and Fix Cable end termination kit for LT 1.1 KV Cable for Cable 50 Sqmm 3.5 Core cable complete all as specified and directed .

Sneh Construction Co