Proposed Thalasserry Heritage project - Museum for Music at Makreri Temple

Amount

Civil Works

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5 : Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.7 : Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.9.3 : Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.33.1 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

od124434/2020_2021 : Exposed Laterate masonry with neatly dressed laterate stone of size 30X20X20cm or nearest size in cement mortar 1:6 for superstructuree above plinth level up to floor two levelincluding all cost of materials, labour charges etc

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.2.25.1 : Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

50.6.7.2 : Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

50.6.1.5 : Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

12.48 : Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

12.49 : Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ).

od125560/2020_2021 : Providing and fixing good quality Anjili wood / Jack wood eve board 20 cm wide including all charges etc. complete.

od125561/2020_2021 : Providing & fixing on roof pressed clay ceiling tiles 30x25mm size of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).

od125562/2020_2021 : Providing & fixing on roof pressed clay tilevalley (Ceramic tile) 20mm thick of approved pattern ceiling over steel frame work complete (steel frame work to be paid separately).

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

50.13.1 : 9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

50.9.1.1 : Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

50.9.2.1 : Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge.using Anjili/ Jack wood

50.9.4.1 : Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

od125578/2020_2021 : Providing and fixing good quality Anjili wood / Jack wood handrails with top section of size 10.00cm x 6.00cm and vertical section of size 4.45cm x 4.45cm.

od125579/2020_2021 : Melamine polishing on wood work ( one or more coat) for new work

od125580/2020_2021 : Preparation of wood surface for melamine polish

od125581/2020_2021 : providing and fixing 8" or nearest size punit antique tower bolt including all cost and labour charges

od125582/2020_2021 : Providing and fixing 4" or nearest size punit antique tower bolt antique including all cost and labour charges windo

od125583/2020_2021 : Providing and fixing 4" SS punit hinges antique ( approved by the architect)including all cost and labour charges.

od125584/2020_2021 : Providing and fixing antique brass handle ring including all cost and labour charges

od125585/2020_2021 : Providing and fixing of door lock: Atom sixturn Lock ultra key ant.

9.48.2 : Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.48.1 : Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm

11.26.1 : Kota stone slab flooring over 20 mm ( average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)25 mm thick

16.86.1 : Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-charge.Area less than 0.50 sqm.

8.3.2 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

16.79 : Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge.

od124376/2020_2021 : Providing and laying rough finish natural granite stone flooring in required design and pattern (90x50 cm or nearest) in linear as well as curvilinear all complete as per the architectural drawing with 50mm thick stone slab over 50mm thick base of sand etc. complete as specified and as directed by the engineer in charge.

od162839/2020_2021 : Supply, Installation, Testing and Commissioning of about 1100 mm W X 700mm D - 4 passenger Elevator using 1.0m/s or 0.75m/s speed, 3 phase 430 volt, 50HZ for main supply and 1 phase, 220 volt , 50 hz for lighting power supply, microprocessor control and multy speed, full collective operation, side opening two panels/ centre opening two panels 700 X 2000 VVVF operating door, Stainless steel Hairline finish wall and ceiling with LED Light, Automatic Rescue Device (ARD) Voice announcer with background music, over load sensor etc complete, including cost of all material, labour for erection, testing and commissioning as per the direction of Engineer-in charge

30.2.2 : Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.3 : Supplying and stacking sludge at site including royalty and carriage upto 5 k.m. lead complete (sludge measured in stacks will be reduced by 8% for payment).

30.2.8 : Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

30.2.9 : Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

od162860/2020_2021 : Supplying and fixing 225x380 mm Post top Light (Classic Medium. Clear Diffuser. Material: Resin Moulded in black ) with 15w Bulb etc all complete as per the direction of Engineer in charge

od162861/2020_2021 : Supplying and fixing following complete Cast Iron 2.5 mtr height ornamental pole , minimum weight 110kg, including the cost of conveying, loading, unloading, erection charge ,foundation bolt, plate, 2.5sqmm wire, etc all complete as per the direction of Engineer in charge

od162862/2020_2021 : Supplying and planting of approved trees species of a height 1.m to 2.m ,at the specified location as shown in the drawing .Rate shall include Cost of plants , planting of trees sapling, replacement of dead trees and maintainance till the competion of project work

od162863/2020_2021 : Providing and Planting of Buffalo grass for Lawn in Ordinary soil including Breaking clods, Watering, Ramming and Sectioning of spoil bank etc., including all labour charges, etc., complete

od162864/2020_2021 : Supply testing and commisioning the following type 5 nos CCTV unit with all accessories - HONEYWELL HWCHABC2005PI 1080p Bullet Camera Fixed Lens 3pt6 mm, HONEYWELL 16 CHANNEL 1080p DVR , WD 4 TB HARD DISK, 0 AMPS POWER SUPPLY, BNC connector (MX), DC Pin Connector, RG 59 Cable supply, 4U Rack with PDU, LG 18.5" Display, as per design, drawing and the direction of engineering in charge.

od162865/2020_2021 : Providing and fixing Two tired open shelf of size 200 x 120 and 5 or more rack using good quality Anjili wood / Jack wood and Plywood as per the direction of Engineer in charge

od162866/2020_2021 : Providing and fixing Table of Size 250x100x80 made of seasoned sheesham wood / sunmica top frame 19 mm commercial ply board with good quality of sunmica finished with sprit polish using Legs 16”x1 ¾”x1 ¾” tapered top rail 2”x1” thick top side rail 2”x1” thick bottom rail 1.5”x ¾’ thick top frame 3”x1” thick. all complete as per the direction of Engineer in charge

od162867/2020_2021 : Providing and fixing Wooden armless chair made of seasoned sheesham wood finished with sprit polish using Front legs 2”x2” tapered, back legs 1 ¼” thick (curved), top rail and seat rail 1” thick, under framing 1 ¼” x7/8” slates 1”x3/8” sheet frame and shape of wood 1 ¾” thick seat slates 1 ½”x1 ½”x3/4 back height 34” seat height 18”, depth 18”, seat front 18”, width of back 16” all complete as per the direction of engineer incharge

od162868/2020_2021 : Providing and fixing Wooden armed office chair made of seasoned sheesham wood, cane seat and back finished with sprit polish , using Front leg 2”x2” turned, back legs 1-3/8” seat rails 2 ½”x2 ½”, back top rail 2 ½”x1” curved shape back slates 1 ¾”x7/8” middle rail 1 ¾” arms 7/8” thick and bottom rail 1 ¾”, width of front of seat 22” width of back 19” of seat (including back legs, 18” height of arms 9” and height of back 38”) all complete as per the direction of engineering incharge

od162869/2020_2021 : Providing and fixing LED Tube set 20W

od162870/2020_2021 : Supplying and installaion of following sizes of 1200 mm sweep. 5 tar rated ceiling fan, with double ball bearing, Aluminium pressure die cast body with Aluminium blades, canopies, hanging Shackle, 30 cm down rod and without speed regulator suitable for 240V 50Hz, AC supply confirms to IS 374/1979 as required complete. (Make crompton- High speedor equivalent approved make)

od162841/2020_2021 : Liaison charge for Preparation of completion Report, Arranging for Inspection, attending to defects report , preparation of as fitted drawing and obtaining approval and receiving the safety certificate for energisation. clearance from KSEB. Fees, deposit including necessary statutory fees/charges

od162842/2020_2021 : Supply Laying, Testing and Commissioning of following 1100V XLPE A2XFY (XLPE insulated Armoured Aluminium)IN existing trench ,cable trays (Note : Inclusive of supply of Anchor Fasteners, straight through joints and necessary 1.5mm thick GI Flat, clamps shall be included in the laying cost).3C x 16Sq.mm XLPE Al.Ar. Incl excavation, 50mm G.I Pipe ,straight through joints if require

od162843/2020_2021 : Supply Laying, Testing and Commissioning of L&T made metering box with single phase Kwh meter class 1 with all the supporting accessories

od162844/2020_2021 : DISTRIBUTION BOARD<br>Supply, erection, earthing, testing and commissioning of the following MOB DB's Metal double Door powder coated including all interconnections and accessories like bolts, nuts and associated civil works. MCB DBs shall have comprising as follows: Double door- Concealed in wall. Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993. IP 52 for indoor IP 54 for kitchen and laundry panels. IP 55 for outdoor . All MCB’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic and discharge lamps and UPS etc. shall be of type D characteristic. LDB -8W DP MCB DB incoming 63A D.P RCCB, 63A ISOLATER, 10A MCB 24 nos etc.

od162845/2020_2021 : CABLING - Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required - 4 core 10 sq mm with factory made clamp and 25mm PVC pipe

50.18.7.3.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm2 - Internal work - Exposed on wall

18.51.1 : Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

18.55.1 : Providing and fixing PTMT stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms

ELECTRICAL

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.3 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.22.5 : Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.180 mm X 100 mm X 60 mm deep

1.23.3 : Supplying and fixing following piano type switch / socket on the existing switch box/ cover including connections etc. as required.15/16 amp switch

1.23.5 : Supplying and fixing following piano type switch / socket on the existing switch box/ cover including connections etc. as required.6 pin 15/16 amp socket outlet

1.33 : Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden blockincluding connection etc as required.

AAYKAYCONSTRUCTIONS

SABANI ENGINEERS

Bidder Name

AAYKAYCONSTRUCTIONS

SABANI ENGINEERS

GLOBAL CONSTRUCTIONS