Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹3.8 LAccepted-AOC | ₹3.8 L | L1 | Accepted-AOC L1 |
| 2 | L2₹3.8 L+₹922.27 (0.24%)Rejected-Finance VILL KHAIJAPUR P O BELKULAI DIST HOWRAH 711322 | HOWRAH | WEST BENGAL | 711322 | ₹3.8 L+₹922.27 (0.24%) | L2 | Rejected-Finance L2 |
| 3 | L3₹3.8 L+₹1,475.63 (0.39%)Rejected-Finance | ₹3.8 L+₹1,475.63 (0.39%) | L3 | Rejected-Finance L3 |
Tender Value
₹3.7 L
EMD Value
₹7,378
Closing Date
8 Jul 2026, 1:30 pmClosed
Executive Engineer (E/M), FAWS-II, EM SECTOR, KMDA
OFFICE OF THE EXECUTIVE ENGINEER FAWS-II, EM SECTOR, KMDA 83/1A, Vivekananda Road, Kolkata, 700006
Supply, delivery, installation of 20 HP submersible pump motor set with allied works in newly constructed replaced well of DTW based pumping station (P.H No-02) of Sultanpur-II zone located near by Khalishakota Boys School under North Dumdum
2026_KMDA_1028928_1
06/EE(E/M)/ FAWS-II/T-01 of 2026-27 Dt.18.06.2026
Open Tender
Electrical Work/ Equipment
Percentage
7 days
North Dumdum Municipality
Please refer Tender documents.
4 documents required · 4 mandatory
₹0
₹7,378
OFFICE OF THE EXECUTIVE ENGINEER, EM, FAWS-II
28 Jul 2026
1 Jul 2026
10 Jul 2026
1 Jul 2026
8 Jul 2026
1 Jul 2026
3 Jul 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | Mechanical works | - | - | - | - |
| 2 | Supply and delivery of clear water vertical wet type submersible pump suitable for borewell conforming to IS:8034 (and as amended therafter) with standard MOC for potable clear cold water and BEE 3 star rated capable of discharging noted M3/hr against head of water column. The pump shall be directly coupled with a continuous rated 2-pole suitable wet type vertical squirel cage induction motor conforming to IS : 9283 (and as amended therafter), suitable for operation in AC Three phase 415V, 50Hz (category B motor). For 20HP, Stage-3, 52m head of WC & 70m3/hr discharge. | - | No | 91,704 | - |
| 3 | Installation of 20HP submerisble pump motor set for any length of pump assembly exceeding 18 meter length by using necessary requisite tools and plantes by lowering the same within the tubewell housing pipe by fitting fixing column pipes and other accessories, fixtures with necessary nuts, bolts and washer and suspending the entire assembly set vertically fixing the same supported by M.S clamps over the top of houysing pipe etc, including transportation of submersible pump motor and all other accessories and equipment from store to worksite as per direction of EIC. | - | No. | 4,677.98 | - |
| 4 | Supply of pump-motor protective device cage (M.S) comprising of clamps etc as per direction of EIC. | - | Job | 1,511.85 | - |
| 5 | Supply of safety clamp for the P/M set 10 mm X 50 mm section as per direction of EIC. | - | Job | 528.42 | - |
| 6 | Supply,fitting & fixing Split type M.S fabricated suitable tube well cover for the tube well etc as per direction of EIC. | - | Job | 1,257.3 | - |
| 7 | Supplying including cost of installation of cast iron mechanical joint Double socket 90° Bend as dim entionally described in IS : 13382/2004 for connecting two plain ends of Cl/DI pipes with C.I body and follower gland, zinc coated MS. fasteners and sealing rubber gasket of EPDM quality as per IS:13382:2004 complete. for 150mm diameter. | - | Nos | 6,165 | - |
| 8 | Cast iron double flanged single door swing Non-Return Valve generally conforming to IS 14846 having body, door cover in graded cast iron to IS 210 Gr. FG 200, body and door rings and bearing block of leaded tin bronze to I.S 318 Gr. LTB 2, hinge pin of ST AISI410 valves suitable for maximum working pressure of 10/16 kg/cm2 and body tested 15/24 kg/cm2. | - | Nos. | 13,952 | - |
| 9 | Cost iron double flanged manually operated sluice valves generally conforming to IS 14846 : 2000, having four faces and spindle nut of gunmetal, inside screw non- rising type quality gunmetal /AISI 410 spindle: seat tested to 10kg/CM2 and body tested to 15kg/CM2, flanges flat faced and drilled to 1S. : 1538 : 1993. Painted black all over with asphalt base paint. Valves tested by closed end method. 150mm | - | Each | 7,487 | - |
| 10 | Supplying including cost of installation of C.I. Mechanical joint All Socket Tee as dimensionally described in IS: 13382/2004 (With Modified Socket). Each Tee consists of One C.I. Body, Three C.I. Follower Glands, Three sealing Rubber Gaskets of EPDM quality (Conforming to IS:5382/85 Type- Sl. No. Description Unit Rate Schedule of Rates 38 4) and Zinc coated M.S. Fasteners . The whole assembly is mechanically and hydraulically tested to provisions as laid down in IS: 13382/2004. Diameter in mm: 150 x 150 x 150 | - | No. | 7,457 | - |
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.07 MB
BOQ_2527132.xls
BOQ • 0.35 MB
Docs1_F2.pdf
Tender Documents • 1.11 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .