Balance work of Construction of Govt. Medical college at Rajouri including parking place Allied works

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) in all kinds of soil including rock and disposal of surplus, excavated earth at dumping sites to be purchased by the contractor and approved by the engineer - in-charge at site for safe disposal of same without damaging private/ public property and all required leads/lifts and carriage. (Complete job)

Banking earth in layers not exceeding 20cm in depth, breaking clods watering, rolling each layer with 1/2 tonne roller, or wooden or steel rammers and rolling every third and top-most layer with power roller of minimun 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, guide banks etc. and all required leads/lifts and carriage. (Complete job)

Providing and laying in position Cement concrete of specified grade including the cost of centering and shuttering–all work upto required level in 1:4:8 (1cement: 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) using crushed stone aggregate including curing, all leads/lifts & carriages. (Complete job)

Providing and laying in position ready mixed concrete manufactured in fully automatic batching plant and transported to site of work by any means, as per mix design of specified grade for reinforced cement concrete work, including the cost of centring,shuttering, finishing and curing etc & also including cost of Admixtures in recommended proportions as per IS: 9103to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge in M-25 grade reinforced cement concrete by using cement per cum of concrete as per the actual design mix. All works upto any floor level & all leads/lifts & carriages. (Complete job)

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars as per design. (Complete Job)

Stone filling hand packed in horizontal on level including cost of stones including all leads/lifts & carriages. (Complete job)

Providing and fixing unplasticised Rigid pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including all fitting and accessories required. including all leads/ lifts, carriages, loading, unloading and handling as per specification and direction of Engineer-in-charge. (complete job).

160 mm dia (working pressure 2.50 kg /sqcm)

315 mm dia (working pressure 2.50 kg /sqcm)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 litre/1 Osqm over and including base coat of water proofing cement paint applied@ 2.20kg/1 Osqm) All works upto any floor level & all leads/lifts & carriages. (Complete job)

Consolidation of subgrade with power road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the subgrade

Construction of sub-base by providing well graded material, spreading in uniform layers on prepared surface, compacting with vibrator power roller and 8 to 10 ton static road roller with smooth wheels to achieve the desired density using River bed Material including all leads/ lifts, carriages, loading and unloading as per specification and direction of Engineer-in-charge. (complete job).

Providing and fixing of interlocking tiles 80 mm thick of M-30 mix conforming to IS- 15658 over 50 mm thick sand bed and locking of tiles at ends with cement concrete M-20 and spraying of dry sand to fill up the joints, vibrations complete in all respects including all leads/lifts & carriages. (Complete job)

Providing and laying 18mm thick Granite of any colour and shape (area of slab upto 0.5 Sqm) gang saw cut flamed (pre moulded and pre polished), machine cut for stairs steps and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing molding and polishing to edge to give high gloss finish etc. complete at all levels.all leads/lifts & carriages. (Complete job)

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc.including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete,i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, (glazing and paneling to be paid for separately) (3.15mm or 10 gauge).

For fixed portion using Powder coated aluminium (minimum thickness of powder coated 50 microns).

For shutters of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). With glass panes of 5.50 mm thickness (weight not less than 13.75 kg/sqm).

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in paneling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing fly proof wire gauze with 0.5mm dia wire and 1.4mm wide aperture in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item).

Deep Drilling of 200 mm dia. Bore hole using ODE X DTTI drilling attachment including driving of 200 mm dia ERW casing pipe including fixing of casing drive shoe(up to 100 mtr BGL) excluding cost of ERW MS casing pipe 200 mm dia

Proviing and fixing/lowering of 150 mm dia slotted pipe/well screen in the suitable water bearing aquifer/strata alomg with bottom plug, colmplete job with stainless steel Johnson's make V-wire screen

Cost of 200 mm dia ERW MS casing pipe

Extraction of casing pipe during drilling

Deevelopment of bore well by air comprssor of adequate capacity for at least 80 hours or trill clear portable drinking water free for impurities and having discharge as per specification is yielded

Stablization and testing of mini tube well by way of over pumping of maximum 4 days using vertical turbine pump set till the clear portable drinking water is achieved during the yield test

Procurment, installation and commisioning of 10000 GPH X 150 mtr. Static head HC pump set for single stage including standby 1 NO and all required accessories (complete job)

Procurment, installation and commisioning of 5000 GPH X 100 mtr. Static head submersible pump set for bore well including stand by 1 No and all required accessories (complete job)

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on all locations ( rising main / water supply distribution with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required including all leads/ lifts, carriages, loading, unloading and handling as per specification and direction of Engineer-in-charge. (complete job).

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Steel work in built up tubular round, square or rectangular including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer including welding and bolting with special shaped washers etc.complete Hot finished welded type tubes including all leads/ lifts, carriages, loading, unloading and handling as per specification and direction of Engineer-in-charge. (complete job).

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineerin- Charge)0.50mm+/- 5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in 240 mpa steel grade5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5 x 55mm) with EPDM seal or with polymer coated J or L hooks,bolts and nuts 8mm diameter with bitumen and G.l. limpet washers or with G.l. limpet washers filled with white lead complete upto any pitch in horizontal /vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including all leads/ lifts, carriages, loading, unloading and handling as per specification and direction of Engineer-in-charge. (complete job).

Supply and placement of Plastic flower pots of required shape & size (Round, Square, Rectuangular) alongwith different species of plants with necessary & required material including all leads/ lifts, carriages, loading, unloading and handling as per specification and direction of Engineer-in-charge. (complete job). (N.S.I)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Make of Accessories :Legrand/MK/Schneider/Panasonic Make of Wires : Finolex/Lapp/Helucable/Panasonic/RR Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

2 x 2.5 + 1x2.5sq. mm

2 x 4.0 +1x4.0 sq. mm

4 X 6.0 +2x6.0 sq. mm

Makes :Finolex/Lapp/Helucable/Panasonic/RR Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of Recessed conduit as required S/F PVC Conduit Makes : Finolex/AKG/Setia/Anchor/BEC/Vinson

S/F modular boxes, base and cover plate : Supplying and fixing following size/modules , GI box alongwith modular base & cover plate for modular switches in recess etc. as required. Makes : Make of Accessories :Legrand/MK/Schneider/Panasonic Make of Wires : Finolex/Lapp/Helucable/Panasonic/RR

1 or 2 module ( 75mm x 75mm)

3 Module (100mmX75mm)

4 Module ( 125mm x 75mm)

S/F power plug point modular type accessories: Supplying and fixing on exisitng GI Box modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 & 5/6 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc as required.

Make of Accessories : Make of Accessories :Legrand/MK/Schneider/Panasonic S/F Modular type switch/socket : Supplying and fixing following modular switch / socket on th existing modular plate & switch box including connections but excluding modular plate etc. as required Make of Accessories : Make of Accessories :Legrand/MK/Schneider/Panasonic

5/6Amp Switch

3 pin 5/6 Amp socket outlet

Telephone socket outlet

S/F modular type electronic fan regulator: Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc., as required. Fan Regulator shall conform to IS11037 Make of Accessories : Make of Accessories :Legrand/MK/Schneider/Panasonic

S/F modular type blanking plate: Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. ITC fluorescent fitting directly on surface :

Installation, Testing and commissioning of pre-wired, fluorescent fitting of all types complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5sqmm FR PVC insulated , copper conductor, single core cable and earthing etc. as required.ITC Ceiling Fan :

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. ITC exhaust fan upto 450mm sweep:

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep Fixing louvers/shutters for exhaust fan:

Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Telephone wiring in existing conduit: Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair Makes of Cat 6 cable : AT&T/Legrand/HP

S/F 'C' series , SP MCB: Supplying and fixing 5 amps to 32 amps 10kA rating, 240 Volts, 'C" series, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole Makes : Schneider(Acti-9)/Legrand (DX3)/ Siemens(Betagard-5SL)

S/F 'B' Series, SP MCB blanking plate Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

P/F M.V. danger notice plate : Providing and fixing M.V. danger notice plate of 200mm x 150mm , made of mild steel, at least 2 mm thick , and viterous enamelled white on both sides, and with inscription in single red colour on front side as required.

P/F HT danger notice plate : Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

upto 35sq.mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

upto 35sq.mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

upto 35sq.mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct/wiremesh cable tray as required.

upto 35sq.mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Submain Wiring in existing conduit: Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit/Cable Tray as required. Makes Finolex/Lapp/RRKabel/Panasonic

4 X 10 sq.mm +2 X 10 sq.mm earth wire

4 x 6 sq.mm +2 X 6 sq.mm earth wire

Supply of following LED lighting fixtures of Philips/Trilux/GE/Wipro makes

38W( Maximum) 4ft LED Surface Mounted light fixture 4000 lumens having minimum system lumen efficiency of 100 Lumens per watt equivalent to Endura LED BN108C of Philips 6500K, L70 40000hrs, pf >0.95, THD<10%, Voltage Input range 140-270V, with short circuit and overvoltage cut off

10W LED Endura Bulkhead IP66 WT202W of Philips

Supply of Wall / Ceiling Fans 230V 50Hz celing fan with double ball bearing with low power consumption of following sweeps: Bajaj/Usha/Khaitan/Havells

1200mm Ceiling Fan

Supply of following sizes of heavy duty exhaust fan as per approved makes : Bajaj/Usha/Khaitan/Havells/Polycab 450mm Sweep

Supply, Installation, Testing and commissioning of following capacity Storage Water Heater of 5 Star Rating including fixing of set of stainless steel pipes , fixing of bolts in the walls etc. Makes : Racold/Bajaj 35 Ltr

Supply, Installation, Testing and commissioning of Floor Mounted Low Voltage panel IP52 suitable for operation on 433V 3 Phase, 50Hz supply, enclosure made of 2.0mm thick CRCA sheet steel material Aluminium bus bar with following switchgears and metering. Necessary arrangement be made for termination of incoming cable and outgoing cables. Contractor to get the G.A. drawings approved before execution.Make of Panel(Shall have CPRI Test Certificate) : ETE Electrogear(Derabassi)/Acubb/BPS/Tricolite/Adlec Incomer : 1000A 4pole Air Circuit Breaker with microprocessor based communicable release, intergrated metering LCD display showing, V,A,kVA,kW, p.f., kVAR, harmonics readings with suitable set of CTsIcs=Icu=36kA - 1 Nos Busbar : 1200A Aluminium TPN Bus bar supported on DMC insulators Outgoings : 630A 4pole MCCB Ics=Icu=36kA - 5 Nos All MCCBs shall be have overload adjustable setting 64-100%, with microprocessor release. MCCB's shall be integrated with digital lcd energy metering unit having realtime current, voltage, power , energy , suitable set of CTs and shall be installed with Rotary Operating machanism. Phase Indication LED Lamps for all incomers and outgoings to be provided. ON Off Trip Indication LED Lamps to be provided for all incomer and outgoings. Mechanical and Electrical interlocking to be provided for all incomersas required as per scheme. Make of MCCB/MCB : Schneider(NSX), Siemens(3VL), Legrand

Supply, Installation, Testing and commissioning of Floor Mounted Low Voltage panel IP52 suitable for operation on 433V 3 Phase, 50Hz supply, enclosure made of 2.0mm thick CRCA sheet steel material Aluminium bus bar with following switchgears and metering. Necessary arrangement be made for termination of incoming cable and outgoing cables. Contractor to get the G.A. drawings approved before execution.Make of Panel (Shall have CPRI Test Certificate) : ETE Electrogear(Derabassi)/Acubb/BPS/Tricolite/Adlec Incomer : 250A 4pole MCCB with intergrated metering LCD display showing, V,A,kVA,kW, p.f., kVAR, harmonics readings with suitable set of CTs, Ics=Icu=36kA - 1 Nos Busbar : 300A Aluminium TPN Bus bar supported on DMC insulators Outgoings : 100A 4pole MCCB Ics=Icu=25kA - 6 Nos All MCCBs with Electronic Release and Phase Indication LED Lamps for all incomers and outgoings to be provided. ON Off Trip Indication LED Lamps to be provided for all incomer and outgoings. Mechanical and Electrical interlocking to be provided for all incomersas required as per scheme. Make of MCCB/MCB : Schneider(NSX), Siemens(3VL), Legrand

Supply , Installation, Testing and commissioning of Automatic Power Factor Correction Panel Indoor type in IP52 protection, floor standing, fabricated of 2mm thick CRCA sheet , duly powder coated . The panel shall be suitable for operation on 415 Volts , 50Hz, 3 phase system with TPN Aluminium Bar , The Capacitors and Switchgears shall be arranged in a modular arrangement duly comprmentalised. Panel shall be complete with earthing arrangement , markings, single line diagram and shall comprise of the following Switchgears and capacitors, refer technical specifications of tender documents for detailed specs.:Make of Panel : ETE Electrogear(Derabassi)/Acubb/BPS/Tricolite/Adlec Incomer : 400A 4 pole MCCB Ics=Icu= 36kA - 1 no. One Set of Indications using LED type indicators Busbar : Shall be of TPN Alluminium rated for 500Amps with heat shrinkable sleeves and mounted on DMC supports Outgoing : 63Amps 3pole MCCB 25kA - 12 no. Capacitor Switching Duty Contactors of following ratings 10KVAR - 12Nos Heavy Duty Resin Filled Capacitors 3 Phase shall have following configuration 10kVAR x 12 APFC Relay of 12 stage shall be used Material Used shall be of list of makes enclosed Shop Drawings to be got approved before manufacturing

Supply & Installation of Wire mesh Hot Dip Galvanised Cable Tray of following sizes including couplers, earthing `Mounting brackets or any other accessories for mounting of cable trays on exisiting steel structure to be erected by the contractor specifically for mounting of cable trays as shown in layout drawings. All accessories required to install cable tray shall be included in the cost of cable tray .

400mm x 50mm

200mm x 50mm

150mm x 50mm

Supply of 1.1kV grade , XLPE insulated, Aluminium conductor, Heavy Duty , Armoured cables of following ratings as per IS : 7098 Part-1 with latest amendments. Makes : Finolex/Havells/General

3.5C x 400sqmm

3.5C x 300sqmm

3.5C x 240sqmm

3.5C x 150sqmm

3.5C x 120sqmm

3.5C x 95sqmm

3.5C x 50sqmm

3.5C x 35sqmm

3.5C x 25sqmm

4C x 16sqmm

Supply, Installation of ABC type Fire extinguishers 6kg , wall mounted of approved makes Safex/Ceasefire/

Supply and laying of Fire Retardant 2.5mm Insulation Mat of Class B 11kV class manufactured as per IS 15652:2006 duly tested by CPRI. Test certificate to be provided by the manufacturer/contractor.Dimension of mat shall be 1000mmx2000mm each

Supply, installation, testing & Commissioning of long life maintenance free Ring Earthing System consisting of UL Listed 1No copper coated 14.2 mm dia Solid steel Rods shall be made of high tensile low carbon steel rod, with molecular bonded with 99.9% electrolytic copper coating of 250 mircon min, minimum length of the earth rod shall be 3 meters . The rod shall be surrounded by Earth Enhancement compound Procem , that has to produce low resistance of an earth termination system and it should not danger to persons and the surroundings 12.5 kg or sufficient quantities required as per the conditions. Heavy duty Fibre Glass Reinforced Under floor earth inspection should have dimension of 250 mmX 150 mm X 130 mm . Flush Mounted, removable and of the earth pit should be able to withstand 5000 Kg. The systems has to be conforming to IEC 60364, IEC 62561, IEC 62305, IS 2309 & IS 3043. Make OBO/Furse/KLK

Supply , Installation of indoor equipotential bonding rail equivalent to 1801VDE of OBO betterman including connections to earth conductors

Supply , Installation of outdoor equipotential bonding rail equivalent to 1801VDE of OBO betterman including connections to earth conductors

Supply and laying 5052 DIN 30x3 flat conductor of size 30mmx3mm , galvanised steel having weight of 70.65kg/100m in ground/at surface.

Supply and laying of 8mm round conductor aluminium RD 8 ALU of OBO

Supply, Installation Testing and commisisoning of following rating 75 kVA UPF ( 3Ph-3Ph ) true online modular UPS with 25kVA Power Modules and SMF batteries providing a time backup of 30 Minutes. Disconnector ( Quanta/Exide makes) for battery protection MS rack, interlinks DC cable from UPS to batteries. UPS shall be supplied with external 75VA Galvanic Isolation transformer (3 Phase in - 3 Phase out). The UPS modules shall be redundant and hot swappable without disruption of supply from other working modules. UPS shall have inbuilt protections against short circuit, undervoltage, overvoltage, surge protection, loss of neutral. Modular UPS enclosure shall be able to accomodate modules upto maximum of 150 KVA for future expansion. Makes :GE/Numeric/APC/Emerson/Eaton/Fuji

Supply, Installation Testing and commissioning of 900/910 KVA DG Set consisting of A. Diesel engine - 16 cylinders, liquid cooled, turbocharged with after cooler, developing 1086 hp @ 1500 RPM, V type, 4 valve per cylinder, electric start, compression ignition, 4 stroke engine designed to run continuously at 1500 RPM confirming to rime rating ISO-3046 standard with an overload capacity of 10 % for one hour in every 12 hrs of operation. Diesel Engine shall conform to latest applicable CPCB norms. The diesel engine shall comprise of Air filter, Lube oil cooler assembly with accessories, Exhaust air manifold, Exhaust Silencer, Expansion bellow, Fuel filter, Lube oil filter, Exhaust gas Turbocharger with after cooler, Radiator with pusher type fan, with fan guard, coolant pump, 24 V (2 x 12 V) electrical starting system with starter motor and battery charging alternator, Common Rail Direct Ignition design for fuel with Electronic Governing & Isochoronus capability, Engine mounting supports, Engine control panel – Microprocessor based Controller, Engine Safeties , Alarms and Trips, K Cool super plus corrosion inhibitor coolant for cooling, Engine Operator/Maintenance & Spare parts CD, Engine Warranty Certificate, Engine test certificate Alternator - 900 / 910 KVA, 415 Volts, 3 Phase, 4 wire, 0.8 p.f. (lag), 50Hz, 1500RPM, in accordance with IS 4722 as per following specifications- Salient poles type, Single bearing, Brushless type, suitable for direct coupling to engine, shall be guaranteed to deliver required output at the ambient temperature condition, suitable for an over‐load of 10% for 1 hour in every 12 hour of operation, Voltage Regulation to be provided with fast response thyristor type electronic automatic voltage regulator, which can holds output voltage within desired limits. (+/‐ 1%)., Excitation: Self excited‐self regulated, Alternator shall be suitable for taking rated load immediately after machine reaches rated voltage and speed , shall be equipped with AREP (Auxiliary regulation Exciting Principle) winding to give performance equivalent to PMG as standard scope of supply, suiitable for direct coupling with Engine and mounted on common fabricated sheet metal base frame, enclosure shall be SPDP IP – 23 degree of protection, Air Cooled type with radial fan mounted on Rotor and Insulation class H as defined in IS – 4722. MS Base Frame suitable for mounting of the offered engine and alternator, fuel tank of capacity 990 litres complete fuel gauge, inlet/outlet connections, drains plug, etc., 2 No. 12 Volts DC Battery of suitable capacity with leads, 1 Set of AVM Pads fitted in Base Frame, All above accessories shall be housed in acoustic enclosure. Makes : Engine : Cummins/Caterpillar/Kirloskar/Ashok Leyland Alternator : Leroy Somer/Kirloskar/Crompton/AVK

Providing Exhaust Stack for 900 kVA DG Set for extended exhaust upto top of building (of appx 25-30m height or as per CPCB Norms ) including steel work, Exhaust Pipe of suitable size, concrete foundation work etc complete job. Contractor shall get the general drawing approved before starting the work.

Supply, Installation , Testing and commissioning of of Floor Mounted Low Voltage panel (DG Set AMF panel outdoor duty IP55) suitable for operation on 433V 3 Phase, 50Hz supply, enclosure made of 3.15/2.0mm thick CRCA sheet steel material Copper bus bar with following switchgears and metering. Necessary arrangement be made for termination of incoming cable and outgoing cables. Contractor to get the G.A. drawings approved before execution.Make of Panel (Shall have CPRI Test Certificate) : : ETE Electrogear(Derabassi)/Acubb/BPS/Tricolite/Adlec/IEC Incomer/Outgoing : 1600A 4P Air Circuit Breaker with microprossor based release Ics=Icu=Icw=50kA, integrated with Digital LCD/LED metering unit , set of suitable CTs - 1No. 2500A 4P Air Circuit Breaker with microprossor based release Ics=Icu=Icw=50kA, integrated with Digital Lcd/led metering unit , set of suitable CTs - 1No. Automatic transfer controller microrocessor based , programmable at site to automatically changeover the supply from Mains source to DG set supply in case Mains power failure. The controller shall communicate with DG set controller in DG Set . The control cable from DG set controller to DG Set Auto Mains Failure panel shall be in scope of this item. UPS of required rating shall be installed in the Panel for control supply. Mechanical and Electrical interlocking to be provided for all incomers as required as per scheme.

Supply of 11m Long 410 SP 56 Swaged tubular pole as per IS 2713

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 10m upto 12m

Supply and laying of Stranded Compact Circular Aluminium Conductor, Conductor Screen With Extruded Semi Conducting Compound , XLPE Insulated, Insulation screening With Extruded Semi Conducting Compound In Combination With Copper Tape, Al Round Wire Armoured And Overall PVC Sheathed Cable Conforming to IS 7098 / (Part-II) 1985 With The Latest Amendments.11kV cable 3Cx120 sqmm Aluminium armoured XLPE insulated cable as per IS 7098 as required at site

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2C x10sqmm

4C x 16sqmm

3.5cx25 sqmm

3.5cx35 sqmm

3.5cx50sqmm

3.5cx70sqmm

3.5cx95sqmm

3.5cx120sqmm

3.5cx150sqmm

3.5cx240sqmm

3.5cx300sqmm

3.5cx400sqmm

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :120 sqmm

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 120 sqmm

R.B.Chopra Freighters Pvt. Ltd.