CA NO CWE/FZR-43/2019-20 SPECIAL REPAIRS TO BLDG NO P-23 (MD ACCN) AT CG COMPLEX GE LUDHIANA

Amount

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc, complete all as specified.

M&L for Rendering 10 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L Rendering 5 mm thick in cement mortar (1:3) on ceiling concrete surfaces finished even and smooth without using extra cement, complete all as specified.

M&L Preparation of newly plastered surfaces and applying two coats of oil bound distemper, over a coat of 3mm wall care putty, and a coat of primer, complete all as specified and as directed.

M&L Preparation of new plastered surfaces of walls etc and applying two coats of cement base paint over a coat of primer, complete all as specified.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash, complete all as specified.

M&L Preparation of old decorated plastered or unplastered surfaces by brooming down with steel wire brush, scarping down smoke soot, mould,moss and efflorescent salts and trading oil, greasy spots and applying two coat of white wash on walls including cornices, pillasters etc, complete all as specified and as directed.

M&L Preparation of old decorated plastered or unplastered surfaces and applying two coats of white wash on ceiling including cornices, pillasters etc complete all as specified and as directed.

M&L Complete removal of existing treatment and preparation of old plastered surfaces of walls after applying two coats of cement base paint over a coat of primer, complete all as specified.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified.

Demolition of un-reinforced cement concrete of any description and in any position, complete all as specified.

M&L for cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in Beam/roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified.

M&L for 25mm thick Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in sub base of flooring, complete all as specified.

M&L for Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in 50mm thick plinth protection, surfaces finished even and fair without using extra cement, including provision of construction joints, complete all as specified and directed

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) complete all as specified.

M&L for kota stone slabs, 20mm to 25mm thick, machine cut as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including screed bed of 15 mm thick in cement mortar (1:6) including rubbing, cutting and polishing (mirror finish) complete all as specified.

M&L for kota stone slabs, 20 to 25 mm thick, machine cut as in shelf, skirting,steps,dado,pillars etc, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including rendering coat of 10 mm thick in cement mortar (1:4) including rubbing, cutting and polishing, complete all as specified.

M&L for Glazed ceramic tiles, coloured (colour & shade as approved), of size 450x300x7 mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over & including 10 mm thick backing coat in cement mortar (1:4), complete all as specified.

M&L for Non skid Ceramic coloured (colour and shade as approved) tiles, any shape, 7mm to 8 mm thick area of each tile exc 0.06 sqm and not exc 0.11 sqm as in flooring, set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles laid over & including 15 mm thick screed in cement mortar (1:6), complete all as specified.

M&L for Non skid Ceramic coloured (colour and shade as approved) tiles,any shape, 7mm to 8 mm thick area of each tile exc. 0.11 sqm and not exc 0.18 sqm as in flooring set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles laid over & including 15 mm thick screed in cement mortar (1:6), complete all as specified.

Dismantling of stone slabs and tiles of any description or thickness in floor, aprons, etc laid and bedded and pointed in any surfaces, complete all as specified and directed.

M&L for granite (of any type) work 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & laid over including 15 mm thick screed bed in cement mortar (1:4), complete all as specified.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius, complete all as specified.

Demolition of un-reinforced cement concrete exc 15 cm thick above ground floors for sunken flooring, complete all as specified.

M&L PCC (1:5:10) type E2 (using 40mm graded aggregate) in filling under sunken floor portion, complete all as specified and as directed

M&L for 15 mm thick screed in cement mortar (1:3) admixed with with WPC complast x 421 IC @ 130 ml per bag of cement including a bonding coat of Nito bond AR cement slurry, complete all as specified.

M&L for applying two coats of approved liquid water proofing chemical coating on the entire sunken portion, complete all as specified and directed

S&F 32mm dia GI pipe medium grade 450mm long beveled cut at both ends etc complete all as specified.

Cutting hole into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement 1:2:4 type B1 as required area not exc 150cm complete all as specified.

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass including roots, vegetation, complete all as specified.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified.

M&L Plain Cement concrete, 20 mm thick (1:2:4), type B-1 using 20mm graded stone aggregate as in roof padding chamfered on edges, incl necessary sloping on roof including form work complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:3) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L for APP based Polymer modified bituminous membrane with sand witched polythene film/non woven polyster reinforcement/polymeric water proofing membrane 3Kg/sqm shall be laid over entire roof surface and on verticle surface up to grooves (or as per manufacturers recommendation) with over laps of 100mm. The over lap shall be sealed by flames or as per manufacturer instruction. Hot blown bitumen grade 85/25 @1.2kg/Sqm applied over the membrane should be compatible with membrane all as recommendation manufacturers and all as specified and directed.

S&F 40 mm thick brick tiles laid over a layer of 25mm thick mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement and including 15 mm thick screed in cement mortar (1:6), complete all as specified.

All as per item No 38 herein before but using old brick tiles retrieved from dismantling (Item No 33 hereinbefore) including cleaning and removal of mortar from tiles, complete all as specified.

M&L for Flush pointing to roof in cement mortar (1:3) including racking out joints brick,complete all as specified.

S&F in repairs 100mm dia PTMT grating with waste hole (Minimum weight 40gms) fixed over trap with cement, complete all as specified.

Taking up or down existing steel water tubing, 15 mm bore alongwith connections fixed/laid in any situation, complete all as specified

Taking up or down existing steel water tubing, 20 mm bore alongwith connections fixed/laid in any situation, complete all as specified.

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceiling, complete all as specified.

S&F Galvanised iron steel water tubing, 20 mm bore, medium grade with all fittings and fixed to walls and ceiling, complete all as specified.

S&F in repair 15 mm bore bib tap of, chromium plated, screwed down, high pressure with crutch or butter fly handle, complete all as specified.

S&F in repair 15 mm bore stop valves of cast copper alloy, screwed down, high pressure with crutch or butterfly handle, complete all as specified.

S&F in repair 20 mm bore stop valves of cast copper alloy, screwed down, high pressure with crutch or butterfly handle, complete all as specified.

S&F in repair 15 mm bore stop valves of cast copper alloy, screwed down, high pressure with crutch or butterfly handle,but fancy type chromium plated with long shank and concealed type complete all as specified.

S&F in repair Vitreous china white squatting pan orrissa pattern of size 580mm x 440mm with connecting flush pipe and 100 mm bore cast iron ‘P’ & 'S' trap with complete all as specified.

S&F in repairs PVC connection 15mm size with brass nuts on both ends, 300mm long, complete all as specified.

S&F in repair 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings, complete all as specified.

S&F in repair 20mm bore ball valve high pressure PTMT with epoxy coated aluminium rod and polythene float and fly nut complete, screwed for iron pipe , complete all as specified.

S&F in repair Brass chromium plated shower roses with or without swivel joints,with shower arm 15 mm dia,195 mm long with bend of 45 degree with flange of CP brass, including fixing to steel pipe or union, complete all as specified.

S&F in repair, 1mm thick stainless steel sink, plugs, washers, PVC waste pipe, union, including cast iron cantilever brackets connecting union etc , overall size of sink 495mmx420mm, bowl size 410mmx330mmx160mm complete all as specified.

S&F in repair, tublar Towel Rail 60cm long 'D' type between flanges of chromium plated 20mm dia fixed to walls, complete all as specified.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts,making good jambs with plaster in CM(1:4) to match with existing finish, complete all as specified.

All as per item No 58 herein before but size exceeding 1.5 Square metre and not exceeding 4 Square metre each and refixing in the same opening.

Taking down door shutter of any description, exc 1 Sqm but not exceeding 2 sqm each, complete all as specified.

M&L for resecuring or easing & adjusting without taking down of shutters of any description of exc 1 sqm and n.exc 2sqm each, complete all as specified.

M&L Mild Steel Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing, complete all as specified.

S&F Factory made, 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 9 mm thick B.W.P. commercial ply or 12mm thick BWR grade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.24(a) of MES Schedule Part-I section-8 complete all as specified.

S&F Factory made 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass/gauge etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified.

M&L Factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and treated with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and treated with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work, complete all as specified.

S&F Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified .

S&F 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube, complete all as specified in MES Schedule Part-I (2009), including making good jambs in CM (1:4) with finishes to match with existing, complete all as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site ,complete all as per specification in MES Schedule Part-I (2009) & drawing.

S&F 250 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts,four on bolts plate and two on staple plate, complete all as specified.

S&F Mild steel butt hinge, 100mm long, medium weight, cold rolled fixed with steel screws or welded to steel frame where required complete all as specified.

S&F 200mm mild steel tower bolts, stove enameled black with bright bolt all as specified.

S&F 125mm mild steel pressed handles oval type stove enameled black all as specified.

M&L Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

M&L Preparation of old treated wooden surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified.

S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified.

S&F 300 mm Mild steel helical door spring including roller and roller plate complete all as specified.

S&F 25mm thick Flush shutters, solid core construction ,with block board core and plywood face panels , with decorative face veneer on both sides for CB shutter complete all as specified.

S&F Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified.

S&F in repair curtain rod MS 25mm dia (outer dia) having thickness 0.63 mm, PVC powder coated colour/pattern, including plastic finial of 28mm bore, decorative type suitable for curtain rod, with mild steel prepainted side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws best quality to suit the curtain rod and fixed to the curtain rod, with suitable adhesive, complete all as specified.

Dismantling CI pipe alongwith fittings of 50/75/100mm bore, below or above ground level or laid in floors, jointed in cement mortar and taking out complete all as specified.

S&F CI bend (any radius) with ducks foot or heel rest of 100mm bore complete all as specified.

S&F 100mm CI sand cast iron Branch pieces, single T (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified.

S&F 100mm CI floor trap with grating including jointing to waste pipe fixed in cement concrete type B1 type (1:2:4) complete all as specified.

M&L for 110 mm PVC (SWR) gully trap, plain with grating including jointing with solvent cement, complete all as specified.

S&F in repairs 75 mm dia spun cast iron soil, waste and vent pipe, sand cast, in any length with or without ears with cement joints fixed to walls with and including suitable clamps, complete all as specified.

S&F in repair, 75 mm bore, cast iron bend (any radius), diminishing pieces or tapers (larger bore measured) with oval access cement joints, complete all as specified.

S&F in repair 75 mm CI sand cast branch pieces single (equal or unequal),ordinary or inverted(spigot or socket type) or with parallel branches, complete all as specified.

S&F in repair 75 mm CI sand cast branch pieces double (equal or unequal),ordinary or inverted(spigot or socket type) or with parallel branches, complete all as specified.

S&F 100mm cast iron sanitary connection socket to fit WC outlet,complete all as specified.

S&F 100mm cast iron sanitary connection short -connections upto 300mm complete all as specified.

Disconnecting existing tanks, 500 litres capacity rotational moulded setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified.

Demolition and breaking up drain pipes of 150mm dia of pipe(Salt glazed stone ware, AC or Reinforced concrete) set in cement mortar complete all as specified.

S&F in repairs 110 mm bore PVC (SWR) Rain water pipes single socket in any length with rubber ring joints fixed to wall complete all as specified.

S&F in repairs 110 mm bore PVC (SWR) bends/shoe and provided with access door any radius fixed to walls including distance pieces and stack clamps, including making good around complete all as specified.

S& F 18-19 mm thick block board exterior grade 1 commercial type fixed as in shelves of cup board, complete all as specified.

M&L 2nd class Soft wood fillets, sectional area exc 13 sqcm but n. exc.23 sqcm, rectangular in section, wrought finished, fixed with PVC rawl plug & steel screw, complete all as specified.

Demolition of reinforced cement concrete in any position, complete all as specified.

M&L pre-cast cement concrete B1 (1:2:4) cover slab for manhole etc using 20mm graded stone aggregate, set in cement 1:4. Complete all as specified.

S&F Mild steel TMT bars 10 mm dia and over as in reinforcement cut to length bent to shape required including cranking, hooking at ends and binding with mild steel wire (annealed) not less than 0.9mm dia FE-500/550 confirming to IS-1786-1985 all as specified.

S&F in repairs 100 mm dia cast iron soil, waste and vent pipe, sand cast, in any length with or without ears with cement joints fixed to walls with and including suitable clamps, complete all as specified.

Taking down carefully existing copper/alumimium point wiring for light/fan/socket out let points complete with fitting and fixtures, battens, wire etc and making good the disturbed surfaces of walls and ceilings, complete all as specified.

Taking down carefully old unserviceable sub main wiring and making good disturbed sufaces and matching with existing complete all as directed and specified.

M&L Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia )duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed,stranded (Green colour) connected to common earth dolly complete all as specified for following:- (a) One light/fan/bell/exhaust point controlled by one single pole one way switch.

(b) One light point controlled by one switch 5 Amps two way.

(c) One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board .

(d) One 3 pin 5 Amp socket outlet point controlled by one switch on same board.

M & L for point wiring with PVC (FRLS) unsheathed, fire resistance, stranded copper conductor of size 2.5 sqmm (nominal cross sectional area ) single core cable in and including rigid non metalic PVC conduit 20 mm dia or higher size "medium " grade ISI marked concealed (surface only on roof & colomns) complete with all accessories/fittings and MS box thickness not less than 1.2 mm covered with 3 mm thick plastic laminated hard glassy surface sheet cover concealed in wall with screws & washers including unsheathed single core PVC (FRLS) insulated cable green in colour 2.5 sqmm stranded copper conductor as earth wire and connecting to earth dolly, for one three /six pin 15/16 amps power socket controlled by one 15/16 amps switch complete all as specified & directed by Engineer in Charge.

Supply and fixing 20 Watt LED lighting fixture (4 Ft) with trimline is a robust high performance batten and LED luminaire comprises of extruded channel in thermally conductive material and high translucent serrated milky white diffuser is used to get glare free and smooth light distribution and connection from ceiling rose to connector complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engr in Charge.

Supply and fixing 10 Watt LED lighting fixture with trimline is a robust high performance batten and LED luminaire comprises of extruded channel in thermally conductive material and high translucent serrated milky white diffuser is used to get glare free and smooth light distribution and connection from ceiling rose to connector complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engr in Charge.

Supply and fixing 5 Watt LED lighting fixture with trimline is a robust high performance batten and LED luminaire comprises of extruded channel in thermally conductive material and high translucent serrated milky white diffuser is used to get glare free and smooth light distribution and connection from ceiling rose to connector complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engr in Charge.

Supply and fix LED Bulk Head fitting 10 watt with pressure die cast aluminium housing for multiple application IP 65 protected complete all as specified and directed by Engr in Charge.

Supply and fix LED security light fittng 25 watt made up of pressure die cast housing with toughened glass and high power LEDs with option secodary optic with IP 66 protection for building security purpose with bracket made of GI pipe light grade 40mm dia 1.2 mtr long bend to shape as required and fixing with two nos MS clamp of size 40x6mm complete all as specified and directed by Engr in Charge.

S&F Switch, piano, flush type, single pole one way, 5 Amps, ISI marked,complete all as specified.

S&F Switch, piano, flush type, single pole two way, 5 Amps, ISI marked,complete all as specified.

S&F Socket outlet,2 in 1, 5 pin, 5 Amp, piano flush type,ISI marked, complete all as specified.

S&F Socket outlet 2 in 1, 6 pin,5 Amp and 15 Amp, piano flush type, ISI marked, complete all as specified.

S&F Switch piano flush button type 15 Amps, single pole, one way,ISI marked, complete all as specified.

S&F Ceiling rose, surface type, backelite 65mmx50mm, 3 terminals complete all as specified.

S&F bell Ding Dong AC 230 volts, single pole, complete all as specified.

S&F bell push Switch, 6 Amps, 1 module, ISI marked, complete all as specified.

S&F in repairs stepped type electronic fan regulator for ceiling fan 1200/1400mm size, 230 volts, 6 Amps, complete all as specified.

S&F in repairs for sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS 2x4 Sqmm single core 650/1100 V, drawn through & including rigid PVC non metallic concealed conduit 25 mm dia including continuous earth wire of size 1x4sqmm, PVC insulated and unsheathed cable copper stranded conductor (green colour) complete all as specified. NOTE:- Two runs of cable, 1 run of earth wire & one run of PVC conduit shall be measured as one length.

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades to store, complete all as specified.

M&L for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc, complete all as specified.

M&L for refixing of ceiling fan at the existing sites and connected with three core PVC flexible cable from ceiling rose to fan, complete all a specified.

S&F Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet,powder coated, SPN DB with 200 Amps rated bus bar, 8 way, FP-42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of MCCBs duly concealed wall, factory made,including making good distrubbed surfaces with matching colour, complete all as specified.

S&F in repairs MCB, SPN, 63 Amps, 240 volts 10 KA duly ISI marked, complete all as specified.

S&F in repairs MCB, single pole, 240 Volt, 16 to 32 Amps, 10 KA complete all as specified.

JAY ANN CONSTRUCTION COMPANY

MEHAT ENTERPRISES

AGNIHOTRI CONSTRUCTIONS