PROVN OF SENTRY POST AND GUARD ROOM WITH TOILET, BATHROOM AND TWO UNINAL POINTS NEAR MAIN GATE OF LANCER LINE II RWA UNDER AGE B/R-I OF AT ARMY AREA JODHPUR

Surface excavation n.exc. 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in any type of soil/rock complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed.

Removing excavated materials (soils) to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.50 above the starting point complete all as specified and directed.

M&L for Anti Termite treatment treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as directed.

M&L for Anti Termite treatment treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and directed.

M&L for Anti Termite treatment treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including wateringas required complete all as specified and directed.

M&L for hardcore of broken stone of gauges n.exc. 63mm, deposited spread and leveled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete and sub base of floor complete all as specified and directed.

M&L for Reinforced cement concrete (M-25 Design Mix) as Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. .

M&L for Reinforced cement concrete (M-25 Design Mix) as Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for Reinforced cement concrete (M-25 Design Mix) as Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for Reinforced cement concrete (M-25 Design Mix) as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L flat fair finished formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L flat fair finished formwork of sides of pillars, posts, struts, piers, columns etc square or rectangular or polygonal rough surfaces of concrete complete all as specified and directed.

M&L for flat fair finished formwork to sides and soffits of floor or roof beams, beam haunchings, columns, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.complete all as specified and directed

M&L flat fair finished formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick flat fair finished surfaces of concrete complete all as specified and directed. .

M&L for rough finished suface of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per item No. 21 specified here-in-above, but 6 to 10mm dia bars complete all as specified and directed.

All as per item No. 21 specified here-in-above, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for Squared rubble walling Jodhpur type, regular coursed, well bonded, bedded and solidly hearted, built in CM 1:6 curved on plan to a mean radius n exc 6m complete all as specified and as directed

M&L for providing precast cement concrete solid building blocks 1:2:4 Type B1 (Using 20 mm graded stone aggregates) or slabs 10cm thick with plain or interlocking joints setting in mortar built in CM (1:4) as in walls complete all as specified and directed.

Supply only integral water proofing compound all as in specified & directed.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on faces other than fair faces of brick work or concrete surfaces using water proofing compound as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on ceiling surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D2 (using graded stone aggregate) as in sub base to floor, incl well compacting & laid to levels etc, complete all as specified and directed.

M&L Machine cut Kota stone slab 20-25mm thick as in flooring laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing over and including 20 mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L Machine cut Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing over and including 15 mm thick backing coat in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including M&L for 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L Glazed coloured ceramic tiles of size 450x350x7/ 350x 250x 7 to 8 mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/ coloured cement to match with existing work over and including 10mm thick backing coat in CM 1:4 to receive dado/skirting complete all as specified & directed.

M & L 20 mm thick machine cut one side polished black granite in kitchen plate form and windows cill, set and jointed including 20 mm thick screed bed in cement mortar 1:3, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing, polishing and moulding complete all as specified and directed.

M&L 50mm thick sand stone slabs in sunshades, chajjas, shelves, cills, landings cover slabs on manholes stones templates etc n exc 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4 thickness including necessary cutting and chiselling complete all as specified and directed.

M&L 75 mm thick PCC 1 : 3 : 6, type C1, (by using 20mm graded stone aggregate) for plinth protection finishing even and smooth without using extra cement, Including expansion joint every three metre and change in direction and joint to be filled with sealing compound Gde A complete all as specified and directed.

M&L for providing PCC 1:2:4 type B0 (using 12.5mm graded stone agg) as in roof padding laid to a minimum consolidated thickness of 50mm to provide a finished slope 1:30 complete all as specified & directed.

M&L for 15 mm thick cement screed bed with CM 1:4 over roof surfaces mixed with water proofing compound as per manufacturee instructions and finishing the surface even and smooth complete all as specified and directed. (Note: - WPC shall be measured and paid separately).

M&L for roof treatment with UV stable single component fibre reinforced elastomeric liquid applied water proofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must. Note : - 1.The authorized applicator of manufacturer shall be approved by GE.

S&F as in repairs for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 mm thick bent to shape incl two coats of synthetic enamel paint on internal surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all specified and directed.

S&F pressed steel frames for doors with one or more rebates including necessary fixing lugs lugs, hinges, lock strike plates etc completed size of frame 125x60mm made out of 1.25mm MS sheets complete all as specified & directed.

S&F for Flush shutters 35 mm thick, solid core construction and plywood face is covered with decorative face with sunmica / veneer with lipping frame edging to match with mortice lock and handle complete all as specified and directed.

M&L gauzed shutter shall be made out of angle iron 35x35x5mm, 25x25x5mm and 1.5mm thick as shown on drawing. The frame for shutter shall be of pressed steel and 10mm Square bars grill complete with fly proof wire mesh having 0.63mm nominal dia wire and 1.4mm average with aperture and 250mm M S sliding bolt , 150mm MS tower bolts and Aluminium 200mm Handle including two coats of synthetic enamel paint over a coat of red oxide all specified and directed by Engr-in -charge.

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Providing & Fixing Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

M&L for PCC 1:2:4 type B1 Mix using 20mm graded stone aggregate as in hold fast iron fixing, coping, chamfered edges including necessary form work complete all as specified and directed.

S&F for MS hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; and similar small articles conforming to Fe-290 Gde-E-165 with welding and necessary item complete all as specified and directed.

S&F of stainless steel butt hinges 100 mm size for WPC door complete all as specified and directed.

S&F Butt hinges, 100 mm long of stainless steel complete all as specified & directed.

S&F Extruded aluminium alloy handles, fabricated type, anodised size of handle 150 mm complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section and fixed length of bolt 150 mm complete all as specified and directed.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 300mm mild steel, ordinary rat rail rod pattern springs including roller and roller plate as in repairs complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality, and glazing with oil putty/beading in square not exceeding 0.50sqm each pane complete all as specified & directed.

S&F 3mm thick figured glass, pin headed, and glazing with oil putty/beading in square not exceeding 0.50sqm each pane complete all as specified & directed.

S&F galvanized mild steel wire cloth with 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified & directed.

M&L Steel window box type using ERW 'P' section comprising double frame for gauged and glazed skeleton shutter jointed internally with flat iron 40x3mm complete including hinges, handle tower bolts stops, lugs etc all as shown on drawing Note (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit (ii) Unit rate quoted against this item shall also include the iron mangeryas shown on drgs (iii) Guard bars glazing & wire mesh shall be measured & paid for separately.

S&F steel windows or ventilators fixed type, complete all as specified & directed.

S&F mild steel framed work such as grills, gratings guard bar etc with ends of bars shouldered and/ or riveted etc completed all as specified.

S&F Wash Basins,Vitreous China, white, flat back, size 550 x 400mm including brackets and cutting for and pinning in ends of brackets or erecting stand including 15mm bore pillar tap cast copper alloy chromium plated fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe fixed with CP Waste coupling 32mm and waste pipe complete all as specified and directed.

S&F vitreous china squatting pan of ‘Orrisa pattern’ size 580x440mm, white with, integral foot rest including replacement of ‘P’ or ‘S’ trap, lime concrete bedding and making good floor complete all as specified and directed.

S&F vitreous china urinal half stall type with including providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified.

S&F PVC low level flushing cistern of 10 ltrs capacity, ISI Marked, white, symphonic action type with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm bore, suitable for low level cistern complete all as specified & directed.

S&F angular stop valve, 15 mm bore, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.

S&F 15 mm bore long body bib cock with wall flange and aerator, brass chromium plated with fancy type and screwed down to 15 mm bore GI tubing or for brass ferrule complete all as specified and directed.

S&F 15mm bore, GI tubing, medium grade, with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

S&F 20mm bore, GI tubing, medium grade, with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

S&F PVC connections 15mm dia and 450mm long suitable for screwing with 15mm bore iron pipe including PTMT nuts complete all as specified & directed.

S&F 15mm bore pillar taps, fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified & directed.

M&L 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed suitable for Urinals complete all as specified and directed.

S&F PVC waste pipes of 40/32mm bore suitable for wash hand basins/sinks complete all as specified & directed.

S&F chromium plated steel grating 125x125 mm square as reqd at site complete all as specified and directed.

S&F for 110 mm bore PVC floor traps plain with grating and 300 mm long outlet including jointing with cement concrete type B-1 1:2:4 complete all as specified & directed.

M&L (SWR) gully trap 125/110mm setting and jointing with solvent cement complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with aluminium alloy brackets and gaurd and railing 60cm long complete all as specified

S&F Brass chromium plated tubular towel rail 20 mm outer dia `D’ type, 60 cm long between flanges with and including chromium plated brass screws and plastic rawl plugs/cleats, complete all as specified and directed.

S&F decorative type curtain rod stainless steel finish with pipe 22 to 25 mm dia with best quality knob metal with double fitting type including stainless steel brackets (trade pattern) fixed to walls complete with two nos decorative stainless steel knobs (fincals round type with mirror optic finish) at each end , sample as approved by GE, complete all as specified and as directed

S&F Hat and coat hooks, solid body of Brass Choromium plated, 175mm to 250mm long and fixed in repairs complete all as specified & directed..

S&F Shower rose size 125mm brass with shower arms chromium plated including fixing to steel pipe or union complete all as specified & directed.

S&F PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified & directed.

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.

S&F PVC bends 110mm bore, any radius complete all as specified & directed.

S&F PVC (SWR), junction single, (Single T) equal or unequal 110 mm bore complete all as specified & directed.

S&F 75mm dia PVC pipe (SWR) single socketed in any length with rubber ring joint, fixed in walls complete all as specified & directed.

S&F PVC (SWR) bends with access door of radius 75mm dia complete all as specified & directed.

S&F PVC (SWR) vent cowl bore of pipe 75 mm complete all as specified & directed.

M&L for Cement concrete 1:3:6 type C2, as in surface channels and drains (using 40mm graded stone aggregate) complete all as specified & directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete

M&L preparation of new or previously untreated wooden surfaces of any description, not other wise described over 10cm width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified & directed.

M&L preparation of new plastered surfaces of walls with Birla /JK wall care putty and applying two coats of Oil bound distemper over a coat of alkali resistant primer to match the existing surfaces as required, complete all as specified & directed.

M&L preparation of new plastered surfaces of walls etc and applying two coats of Plastic emulsion paint (weather coat) over a coat of primer paint plaster complete all as specified & directed.

M&L for 100mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base to floor, incl well compacting & laid to levels etc, complete all as specified and directed.

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for two coat of synthetic enamel paint over a coat of priming surfaces on new concrete surface including preparation of surface complete all as specified and directed.

M&L for connecting 40 mm bore GI pipe from existing water supply line including necessary excavation, clamping making holes to existing pipe line complete all as specified and directed.

M&L for Galvanised pipe medium grade 40 mm bore laid in trenches /fixed in wall with all fitting complete

S&F 20mm bore Ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F 40mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 40 mm bore and fixed

S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore and fixed

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks double layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F for 500 Ltrs capacity of tank rotational moulded polythene water storage tanks (cylindrical vertical with closed top hoisted and fixed in position white/ coloured including tank led cover with fixing arrangement inlet/outlet/over flow checknut etc complete all as specified and directed.

M&L for 100 thick PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in water tank platform over roof top finished even and smooth complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in copings, bed plates, plinth courses, parapets and the like including weathering, slightly rounded or chamfered angles and throating including use and waste of necessary form work etc complete all as specified and directed.

Providing precast RCC type C1 using 20mm graded aggregate as in cover slab for man hloes set in CM 1:6 complete all as specified and directed.

M&L for cutting to bituminous road for laying of RCC hume pipe any dia & making good as per road specification and as per direction complete all as specified and directed.

Supply and laying in trenches, aligning and jointed for DWC HDPE pipe ID 150/172 mm, SN-8 laid in trenches complete with coller fixed and jointed rubber ring and couplers and tested completed all as directed.

M & L for PCC 1:3:6 type D2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150/172 mm bore complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains required dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) 1:2:4 type B1 smooth finished & reforming benching as reqd complete all as specified and directed.

M&L for modular point wiring complete with 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FRLS cable (RYBN) 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit 20mm dia with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FR-LSH cable (Green) 1100 Volts grade as earth continuity wire connected to earth dolly and including modular sunken galvanized terminal boxes of same make of switch/ socket/ regulator with sleek and curvy cover plates, for mounting of modular switches, sockets, fan regulators complete for the following :- (a) One light/fan/bell point controlled by one, one way switch.

All as per Sr. item No.114.00 here-in-above, but suitable for One socket outlet 3 pin 6 amps on the same board controlled by one no 5 Amp switch.

All as per Sr. item No.114.00 here-in-above, but suitable for One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

All as per Sr. item No.114.00 here-in-above, but with using 2.5 Sq mm single core multistanded copper conductor cable for 3 pin 16 Amp socket outlet on independent board.

S&F modular switch 1 way 6 Amp, 1 module complete all as specified and directed.

S&F modular switch 1 way 16 Amp, 1 module complete all as specified and directed.

S&F modular socket 6 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F modular socket 6 Amp/16 Amp, 6 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 230 Volts AC with polycarbonate body complete all as specified and directed.

S&F LED light fitting 1 X 20 watt 220 V AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed.

S&F LED lamp 9W complete all as specified and directed by the Engineer-in-Charge.

S&F LED street Light fitting 35 Watts 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with dirver lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including GI pipe 40 mm bracket of 1.5 m in lenght including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable, complete all as specified and as directed.

S&F ceiling fan complete with blades, down rods electronic modular regulator and accessories, 230 V 1200 mm sweep Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed

Supply,testing and installation in replacement electric storage geyser of capacity 25 Ltrs, BEE 5 star rating, 230Volts, AC, 50Hz, comprising of heating element 2000 watt, storage type steel body with copper tank, puff insulation,both power indicating LED lamp and heating indicating LED lamp neccasry suitable 3 core copper cable,suitable plug top, inlcluding supply and fixing of inlet and out let connection to geyser with steel grip,chromium plated PVC connection of 862mm in length - 02 Nos (one for inlet GI pipe and other one for outlet connection) suitable to connect inlet GI pipe 15mm dia and out let GI pipe 15mm dia (out let PVC connection should be capable to withstand the designed temparature of Geyser) and geyser shall be fixed on wall surface with wall mount bracket and 10 cm anchor bolts as required inclduing all necessary plumbling works and civil works complete all as directed and as specified.

Supply & fixing as MCB DB SPN (double door) 8 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall incl dismantling of old UNSV DB all as specified and as directed.

Supply & fixing as MCB DB SPN (double door) 4 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall incl dismantling of old UNSV DB all as specified and as directed.

S&F MCB, B Curve type, 10KA, 6 to 32 Amp, 240 Volts single pole with overload and short circuit protection, complete all as directed.

S&F MCB, B Curve type, 10KA, 63 Amp, 240 volts SPN with overload and short circuit protection, complete all as directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60 x x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal/hard/dense ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion . Note : Rates are deemed to be included for necessary earth work , earth pit with RCC cover of size 300X300 x25 mm etc complete

S&F Heavy duty Exhaust fan 300mm sweep, 900 RPM, including louvers with cutting chases on brick wall and grouting with nut bolts, voltage 230 V, 50 Hz, Copper winding complete all as specified and directed.

S&F wall fan 3 blade AC single Phase 400 mm sweep 230 V ISI Marked complete all as specified and directed.

Supply and installation desert cooler electric driven (single Phase), three speed having nominal air flow capaicty 5000 CFM per hour, with propeller ISI cooler fan motor copper winding single phase fitted with/ having aluminium blade of mild steel galvanized iron sheet and water tank made out of 18 SWG, having capacity 40 Ltr minimum including three louvers iwth wood pad, flexible PVC distrubution pipes and 3 way junction complete all as specified and directed. Note:- 1. Three speed switch ISI marked rotary type for propeller fan and one way switch pump with separate control. The switches shall have marking off Low- medium and high. 2. Float valve on water supply connection shall be deemed to be included in unit rate quoted. 3. Rate are deemed to included in the quoted rate for sutiable size of cooler stand.

Note:- The contract sum shall be arrived after deducting amount of sch of credit from the quoted amount.