E Tender 11/EDC(K)/2025-26

Supply Item

E-CLAMP FOR 11kV

Holding Clamp for SP-33 without N/B

Bracing Clamp Bottom SP-55 with N/B

PG CLAMP 95-25 SQ.mm.

EARTH WIRE CLAMP FOR SP-55 WITH N/B

PP & CLAMP WITH N&B ST POLE SP-55

STAY CLAMP FOR SP-33 WITH NUT & BOLT

PG CLAMP ALU ALLOY DOG TO DOG

STAY CLAMP FOR ST POLE WITH NUT BOLT

SUSPENSION CLAMP

MS CLAMP WITH N&B FOR DISTRIBUTION BOX

DEAD END CLAMP FOR AB CABLE

HT Stay Insulator

DIST. BOX WITH N&B ABCABLE 3PH-8WAY

Piercing Connector 120-25sqmm

NUT and Bolt 100 X 20 MM

BRACING CLAMP TOP WITH N&B SP-55

LT ACB OUT DOOR 400A

MCCB DISTRIBUTION BOX-400KVA

AL CRIMPING TYPE LUGS 25 SQ.mm

AL CRIMPING TYPE LUGS 400 SQ. mm

Electrification Works

Chemical Earthing:Earthing of distribution transformer including digging of pit of size 2.5 Mtr depth and make hole of size 150 mm. Placing of earthing electrode (to be supplied by contractor as per drawing No. A) as drawing B, connecting the same with G.I. Strip (to be supplied by contractor ) of size 35x6 mm as per drawing C for a minimum lenght 6 m. treatment of soil with highly condctive substance as per IS 30343 complete in all respect, result of earthing resistance to be recroded in M.B. before and after installation of earthing. The earth resistance after earthing should be less than 1 Ohm.

Earthing of support with M.S. Earth rod of 2.5 meter long by hammaring of M.S. Rod to proper depth and connecting the earth electrode with the helpof G.I. wire as per construction manual.

Fabrication of M.S. Channel Angle iron after cutting in required sizes with drilling of holes upto good finish for top channel, bracing and special type bracket etc. as per RESSPO schedule and local approved drawing.

Excavation of earth for Stay pit of size 0.6x0.6x1.2mtr in all type of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work

Fixing , tightening and nozzaling of LT Stay with pole and stay rod on required tension as per drawing / RESSPO manual.

Fixing , tightening and nozzaling of 11 KV Stay with pole and stay rod on required tension as per drawing / RESSPO manual.

Grouting of Stay in size 0.6x0.6x0.3 in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement,sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO Manual.

Excavation of earth for pole pit of size 0.9x0.6x1/6 of full length of pole for erection of pole in all type of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work

Erection of Single SP-33 pole in proper level and alignment alongwith fixing of all accessories, like top channel & clamps as per RESSPO construction Manual.

Erection of Single SP-55 pole in proper level and alignment alongwith fixing of all accessories, like top channel & clamps as per RESSPO construction Manual.

Erection of SP-55 Double pole in proper level and alignment alongwith fixing of all accessories, like top channel, X-bracing & clamps as per RESSPO construction Manual.

Grouting of pole in size 0.45x0.45x1/9 of the support in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement,sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO construction Manual.

Muffing of poles size 0.45 cm x 0.60 cm radious with cc 1:3:6 (1 cement : 3 coarse sand : 6 graded stone 10mm nominal size) block size 45cm height from ground level including cost of cement, stone and sand etc.

Painting of SP-33 poles with angle and channel and all steel part by one coat of Rod Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

Painting of SP-55 poles with angle and channel and all steel part by one coat of Rod Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

LAYING OF LT SERVICE CABLE(OVERHEAD)

LAYING OF LT PVC CABLES(UPTO 150 SQMM)

EXCAVATION OF EARTH FOR DTR PLINTH

CEMENT CONCRETING WORK DTR PLINTH

BRICK WORK IN 1:4 RATIO DTR PLINTH

RCC WORK OF DTR PLINTH.

CEMENT PLASTER ON DTR PLINTH

FENCING OF DTR

Installation of new 250 KVA Tranformer on plinth structure and fixing of channel / angle etc. and making all connections of Ht and LT side and its complete commissioning.

Mounting & Fixing of TPMO on double pole structures including making of connections complete work

Mounting & Fixing of Fuse sets on double pole structures including making of connections complete work

Mounting and Fixing of Lightning arrestor set (3 Nos.) on double pole structure including making all connections by G.I. strip size 35x6 mm to earth point complete work (excluding cost of G.I.Strip)

ERECTION OF BRACKET IN 11 KV LINE

Laying, Spreading, Stringing and sagging of HT Line in 3 phase (3 Phase 4 wire) of ACSR Dog Conductor as phase wire with G.I. earth wire complete including fixing of all accessories in 3 Nos. conductor in parallel with binding and jumpering as per profile and profile and sagging chart.

GUARDING OF LT/11 KV LINE

T-OFF CONNECTION COMPLETE 11 KV LINE

Providing and fixing of Danger Board and number plate complete by providing clamps of M.S. Flat 50x6 mm and Nuts & Bolts, danger Boards of M.S. Sheet 2 mm Thick 11''x7'' size (Including cost of all material)

LAYING OF AB CABLE OF SIZE 120 SQMM

MAKING OF SECTION POLE

Cartage of SP-33 Poles from store centre to construction site with loading, unloading at both points. (loading, unloading pluse carriage per pole) and proper stacking. 0 to 20 KM

Cartage of SP-55 Poles from store centre to construction site with loading, unloading at both points. (loading, unloading pluse carriage per pole) and proper stacking. 0 to 20 KM

Cartage of other material (other than poles) by vehicle fro Store Center to nearest construction site Store including loading and unloading at both ends. 0 to 20 KM

Cartage of the 250 KVA capacity transformers from store center to construction site with loading and unloading at both points. (Loading, unloading plus carriage of T/F) 0 to 20 KM

Erection of LT ACB 800 A CT with panel

Digging of Pit through Hammer at CC, DAM

INSTALLATION OF ACB LT DISTRIBUTION BOX

HIMALAYA BUILDCON (BID ID -395309)

PERFECT ELECTRICALS AND ENGINEERS (BID ID -395421)