PROVN FOR PARKING SHED POL STORE AT BUILDING P 19 FOR SQNS AND PROVN OF CERTAIN MINOR WORKS AT SU AND OTHER SITES AT AF STN JODHPUR UNDER GE AF JODHPUR

Amount

M&L for excavating in post holes (or similar holes) each n. exc. 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n.exc. 50 m and making good surface in soft /loose soil complete all as specified & directed .

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concreting complete all as specified and directed

M&L for PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in foundation filling and mass concreting complete all as specified and directed.

M&L for mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS1161-1979 grade St.-240 complete all as specified and directed.

S&F rolled mild steel work in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe-410W Gde E-250 quality 'A' complete all as specified and as directed.

S&F plates (plain or chequered) channels, square cut or notched ordinary or counter sunk) forming holes, without any attachment confirming to Fe-410W Gde E-250 quality 'A' complete all as specified and as directed.

M&L for preparation of newly or previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise, described and applying two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and as directed.

S&F pre-painted galvalume GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

M&L for removing excavated material to a distance exc. 250 m but n. exc. 500 m and depositing where directed complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base to floor finished fair and even all as specified and directed.

M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified & directed .

M&L for providing precast cement concrete block or slab 150 mm thick 1:2:4 type B1 using 20 mm graded stone aggegate with plain or interlocking joints as directed, set in CM 1:6 kerbing/edge block to hard standing/footpath including necessary formwork complete all as specified & directed .

S&F Welded steel wire fabric not exc. 4 kg per sqm fixed to wood or steel members complete all as specified and directed.

S&F complete FIRE ALARM PANEL non addresseble type (Conventional type) 4 zone suitable for automatic fire detection & alarm system including battery 12 V,7 AH - 02 Nos complete all as specified & directed.

S&F manual call point conventional type all as specified and directed.

M&L for 1.5 sqmm 2 core FRLS multistranded copper conductor cable drawn through and including stove enamelled steel conduit 20 mm dia fixed on wall/ceiling with all accessories including fixing accessories complete all as specified & directed.

Supply and fixing of Response Indicator (RI) suitable for Automatic Fire Detection & Alarm System complete all as specified & directed.

Supply and fixing of conventional type Photo Electric Smoke and Heat Detector combination suitable for Automatic Fire Detection & Alarm System complete all as specified & directed.

S&F Fire Alarm Sounders / Sirens Electronic type horizontal single stage continous normal operation for atleast 50 minutes with sound level 65 DB to 120 DB measured at 1.5 Mtr with sound output variation of + 5 DB 500 Mtrs range complete all as specified and directed.

Material & labour for sub main wiring with two runs of 1.5 Sqmm FRLS cable multistranded copper conductors 1100 volt grade IS- 694 marked drawn through and including surface steel conduit pipe medium grade ISI marked (not less than 20 mm dia) along with fittings and all accessories on wall/ ceiling surface and including one run of 1.5 sqmm FRLS cable multistranded copper conductors 1100 volt grade IS- 694 as earth continuity conductor complete including taking down existing sub main wiring all as specified and directed by Engineer in charge. Note : Two runs of main wire and one run of earth wire & one run of steel conduit shall be measured and paid as one length.

Supply, installation, testing & commissioning of hi wall split units indoor/outdoor BEE 5 star rated (evaporator & condenser shall be of copper), copper tubing of required size for proper installation and outdoor unit stand complete with cordless remote control unit and with inbuilt air ioniser and plasma filter for better indoor air quality of capacity 1.5 TR 230 volt AC supply complete all as specified & directed.

Supply & fixing voltage stabilizer for automatic operation,single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy + 2.5 % and of capacity 3 KVA complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil all as specified and directed.

M&L for Pre-cast cement concrete 1:3:6 type C1 (20MM graded aggregate)block masonry with solid blocks, exc. 10 cm in width and setting in mortar1:6 complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work, vertical or to batter including flat & fair finished surfaces complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finsihed surfaces of concrete complete all as specified and directed.

M&L for formwok to sides and soffits of floor or roof beams, beam haunchings, gridesrs, bressummers, lintels, cantilevers, shelves includings supports, overhangs, etc, also splays b/w floor and beams etc complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thck (Horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roffs and sides of RCC/PCC bands in walls, horizontal or slping, and similar work all exceeding 20 CM wide complete all as specified and directed.

M&L for formwork to chullah hoods, Chajjas, troughs and similar items including edges complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT bars 6 mm to 8 mm dia in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for RCC M-25 Design Mix (using 20mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 Design Mix (using 20mm graded stone aggregate) in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC M-25 Design Mix (using 20mm graded stone aggregate) in beams, cantilevers, bressummers, over 1.5M span complete all as specified and directed.

M&L for RCC M-25 Design Mix (using 20mm graded stone aggregate) in Chajja complete all as specified and directed.

M&L for RCC M-25 Design Mix (using 20mm graded stone aggregate) in slab supported on walls, beams and columns in fllors, roofs, laandings, balconnies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and directed.

Removing excavated material exc. 1.50 km but n exc.5 km and and depositing where directed

M&L for hardcore of gauge n exc.50 m and depositing spread and levelled in layers n exc15 CM thick watered and rammed to a true surface complete all as specifed and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc 15 cm thick sprad, levelled and rammed including watering complete all as specified and directed.

M&L for Damp proof course 40 MM thick in cement mortor 1:2:4 type B-0 ( using 12.5mm graded stone aggregate) to horizontal or vertical surfaces including necessary formwork all as specified and directed.

M&L for Rendering 15mm thick on Concrete/Block masonry surfaces in CM (1:4) including finished surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 15mm thick on Concrete/Block masonry surfaces in CM (1:6) including finished surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 5 MM thick in CM 1:3 on fair concrete surfaces in ceiling finshed even and smooth without using extra cement complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Deport Tinted) with silicon additives @ 1.43 Litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 liter/10 Sqm over new Surfaces complete all as specified and directed.

M&L for preparing undecorated newly plastered surfaces of ceiling and applying three coat of white wash complete all as specifed and directed.

M&L for Preparing undecorted newly plastered surfaces of wall and applying two coat of fire proof water base emulsion paint (white or tinted) as per approved shade/coloured on walls complete all as specifed and directed. Note:- Qouted rated shall be deemed to be included for work in building/structure of any height.

M&L for Framed work such as grills, gratings, and hung as gates including pintle hingses, stops, hand-made sliding bolts, etc with ends of bars shouldered and/or riveted, or forged in to spikes, framed guard bars,barred iron doors, laddres, framed blausters, walk ways, railings, Frame work of water tanks and similar work conforming to Fe-410-W(Gde-E-250) quality B complete all as specifed and directed.

S&F Mild Steel, plain, black sheet 1.25 mm thick in steel gates and similar work, cut ot size holes punched including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams including bending or turning up, mitred angles, etc as required complete all as specifed and directed.

S&F Mild Steel sliding door bolt 375mm long, plate type,stove enamelled black , with bright bolt not less than 12mm dia and including minimum of 6 bolts and nuts,four on bolt plate and two on staple plate and fixed complete all as specified and directed.

M&L for 10 MM thick rendering in cement mortor 1:3 mixed with water proofing compound @ 3% by weight of cement, on existing concrete surfaces on roof finshing surfaces even and smooth with out using extra cement complete all as specified and directed.

M&L for preparing new surfaces or foof and applying two coats of Polyurethane (PU) acrylic based water proofing liquid compound over and including a coat of diluted elastomeric self primer and reinforcement fabric sheet as per manufacturer's instruction to stop leakage/seepage from roof/wall complete all as specified and directd by the Engineer -in-Charge.

M&L for 75 MM thick plain cement concrete 1:3:6 type C1 (using 20 mm graded stone aggregate) as in plinth protection laid in panels including necessary formwork, finished even and smooth without using extra cememt complete all as specified and directed

Supply and fixing LED light fitting 2x16 Watt flame proof, CMRI certified recommended for gas/ vapour group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed.

S & F Flame proof weather proof DB SPN DB 8 way MCB DB complete all as specified and directed.

Supply and fix Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and directed.

S & F MCB SP, 6 to 32 Amp, 10 KA, 'Ç'series complete all as specified and directed.

S & F MCB SPN, 6 to 32 Amp, 10 KA, 'B'series complete all as specified and directed.

Supply and fix flame proof exhaust fan, 300 mm sweep (12") ,0.25 HP motor,1440 RPM,1120 CFM, single phase complete all as specified and directed.

Supply, laying , testing and conmmissioning cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with conductor of size 16 sq mm 2 core stranded aluminium complete all as specified and directed.

M & L for Earthing complete with galvanised steel earth plate electrode 60X60cmX 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, precast RCC 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM (Weight not less than4.00 Kg/Square metre) with PCC frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm mmbore midium grade GI protection pipe, test point etc complete all as specified and directed. Note:- (i) Item includes the cost of 7.5 metre GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5 metre GI earth lead.

Removal of excavated material to distance 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point in soil complete all as specified and directed by Engineer-in-Charge.

Material & labour for sand cushioning for LT cable with tibba sand one layer of 80mm thickness before laying of cable and other layer of 150 mm thickness after laying of cable and punning down to 180mm to provide a required cover complete all as specified and directed by the Engineer-in-Charge. Note- Punned thickness only shall be measured and paid.

Supply and laying of 40 to 50mm thick rough dressed jodhpur type stone cover 25 to 30 cm wide and not less than 50cm in length for under protection of cable all as specified and directed by the Engineer-in-Charge.

D DEV COMPANY

Keystone Constructionare