SPECIAL REPAIR TO BLDG NO. P-18 MES OFFICE AND ADDN/ALTR TO GROUND AND FIRST FLOOR OF BLDG NO. P-21 AT NAVAL BASE OKHA UNDER GE NAVY PORBANDAR

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, such as sunken floor, roof padding etc complete all as specified and directed.

M&L for plain cement conctete 1:2:4 type B1, using 20mm graded stone aggregate as in padding on roof using integral water proofing compound @ 2% by weight of cement, finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and directed. (WPC will be measured and paid separately).

M&L for applying roof treatment on top of accessible roof with APP modified membrane (minimum 3 mm thick) weight not less than 3.00 Kg/sqm and reinforced with non-woven polyster reinforcement/mat (centre core) with thermal insulation with plain polythene finish on upper side of membrane, laid by torch application method with overlaps 150 mm on length side and 100 mm on the width side as per manufacturer’s instructions over a coat of approved cold applied bituminous oil based primer (IS-3384) @ 300 gm/sqm complete all as specified and as directed by Engineer-in-Charge.

Supply only integral water proofing compound complete all as specfied and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for 50mm thick cement concrete 1:3:6 type C2, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

Dismantling of asbestos cement (corrugated, semi corrugated, etc) sheets in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F mild steel rolled section Fe-410-W(Gde E-250), quality 'A' as in post, main and cross beams, rafters, purlins connected to common rafters fixed with angle iron clips or other connecting plates complete all as specified and directed.

Taking down chowkats or frame of steel window/ ventilator n exc 1.5 Sqm each (without taking off shutters from the frames) complete as specified and directed.

Taking down shutters of description exc 1 sqm and not exc 2 sqm each complete all as specified and directed.

Taking down chowkats or frame of any descrip tion exc 1.5 Sqm each and n.exc 4 Sqm (without taking off shutters from the frames) complete as specified and directed.

M&L for anodised aluminium frame/shutters for doors, windows ventilators with one or more rebates with powder coating min thickness 50 microns including joining cleat for fixing etc. complete all as specified.

S&F 4mm thick Sheet glass, ordinary quality with and including neoprene beadings in square nexc 0.5 sq.m in each pane with Solar control film 25 micron reflective type sticked to glass panes as per manufacturers instructions complete all as specified and directed.

S&F 3mm thick Figured glass, pin head type and glazing in squares n exc 0.5 sq.m in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to wooden door Shutters/aluminium sliding shutters complete all as specified and directed.

S&F Door closer hydraulically regulated of aluminium (extruded section) body, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F Mortice lock of mild steel, vertical type of size 75mm with duplicate key for door complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 250mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 150mm size, aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F aluminium, anodised barrel tower bolt of extruded section and fixed 200 mm of size complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

Taking down aluminium decogrill of any size and any type complete all as specified and directed.

S&F aluminium grill with and including suitable aluminium anodised frame F/H section as requird manufactured by M/S Decogrill as per design No DG- 102 5.5x5 mm thick complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of old wooden surface of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old steel surface of any description exc. 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F in repairs 20mm dia,stainless steel, fancy type, tubular curtain rod fix on decorative brackets with decorative globe at both ends complete all as specified and directed.

S&F in repair statinless steel bracket for curtain rod of 25mm dia for fixing in walls etc complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L Non-skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc. set & jointed in net cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed

M&L for coloured glazed ceramic tiles of size350x250x7mm/450 x 350 x 7mm thick on vertical surface such as skirting/dado, set and jointed in net cement slurry and pointed in colour cement to match ver 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm but including 600 x 600mm size in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm but including 600 x 600mm size as in dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for exterior ceramic cool roof tiles 300x300x8mm, white, square edged, used for heat insulation and acid resistance and having solar reflective index value above 90 complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness laid, bedded and pointed in any mortar complete all as specified and directed.

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M & L Marble (Baroda/ Udaipur green) 20mm thick machine cut as in flooring & skirting, including 20mm thick screed bed in CM 1:4, jointed and pointed with grey cement slurry and pointing with white cement (1:3) using marble dust with admixture of pigment to match with shade cutting and polishing etc complete all as specified and directed.

M&L for rounding to edges of stone slabs two edge full round,such as in steps,cooking platform and other similar situation complete all as specified and directed.

S&F in repairs false ceiling at any height, 600x600mm grid with Armstrong 'Prelude XL 32' grid system and 16mm thick mineral fibre acoustic tile 'RH-99 classic lite' with suspension system complete all as specified as per manufacturer's instruction ccomplete all as specified and directed.

M&L for designer ceiling made out of plaster of paris properly cut and fixed, including smooth finishing of edges and also provision for electrical arrangements complete all as specified and directed.

S&F 4mm thick PVC sheet fillet of width 35mm for wall panelling including fixing to wall to make PVC frame as per specification and as directed complete all as specified and directed.

S&F solid panel PVC wall lining consisting of 4mm thick wood grain printed PVC sheet (approved colour and shade) inclusive of solvent cement and fixing to PVC frame as per specifications and as per manufactuerers recommendations complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar all as specified and as directed by Engr-in-Charge.

M&L for walling of Porbandar stone masonry well bonded and solidly hearted built in CM 1:6 complete all as specified and directed.

Taking down cement or cement lime plaster, any description on stone walls etc incl raking out joints hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for rendering 10mm thick cement plaster 1:6 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in (1:3) cm on fair faces of ceiling complete all as specified and directed.

M&L for rendering 15mm thick cement plaster 1:4 on stone masonry surface or surface other than fair face of brickwork surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or un-plastered surfaces and applying three coats of white wash on ceilings complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces and applying one coat of white wash on ceilings complete all as specified and directed.

M&L for preparing old plastered or un-plastered walls surfaces and applying one coats of white wash on walls complete all as specified and directed.

M&L for preparing of new plastered or un-plastered surfaces and applying two coats of oil bound distemper over a coat of primer over and including wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old plastered or un-plastered surfaces and applying two coats of oil bound distemper over a coat of primer over and including wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of antifungal exterior emulsion paint over a coat of wall care putty and resin primer (100% acrylic) as per approved design complete all as specified and directed by Engineer-in-Charge.

M&L complete removal of existing treatment of wall and preparation of old plastered or Un plastered surfaces of wall and applying two coats of antifungal exterior emulsion paint over a coat of wall care putty and resin primer (100% acrylic) as per approved design complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight -210 Gms) complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of capacity 500 Litres (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR-Part-I including disconnecting and removal of old U/S PVC tank complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

S&F Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc pipes incl cutting/chases of walls etc 15mm including fitting (such as elbow, tee, reducers, couplers short pieces, connection uion etc) whatever required as per dmanufacturer's instruction fixed on wall /ceiling complete all as specified and directed.

S&F Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc pipes incl cutting/chases of walls etc 20mm including fitting (such as elbow, tee, reducers, couplers short pieces, connection uion etc) whatever required as per dmanufacturer's instruction fixed on wall /ceiling complete all as specified and directed.

S&F 32mm bore, low density polyethelene pipe(LDPE) of pressure rating 6Kgf/Sqcm fixed to wall, ceilings or in floors etc complete all as specified and directed.

Dismantling of cast iron , SGSW, PVC or reinforced concrete drain pipes jointed in neat cement mortar and taking out of trenches if required.

S&F 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors/ walls complete all as specified and directed.

S&F 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches or in floors/walls complete all as specified and directed.

S&F PVC (SWR) bends of any radius with oval and access door of 75mm dia complete all as specified and directed.

S&F PVC (SWR) bends of any radius with oval and access door of 110mm dia complete all as specified and directed.

S&F PVC (SWR) vent cowl of 110mm dia complete all as specified and directed.

S&F PVC (SWR) Floor/ Nahani trap with grating of diameter of outlet 75mm including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed.

S&F in repairs 8mm dia brass chromium plated health faucet(Hand shower) with 01 metre long flexible tube and wall hook complete all as specified and directed.

S&F in repair vitreous china table top wash basin, white, flat back of size 550mm x 400mm including grouted in cement mortar 1:2 on Granite top supported on RCC slab complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

Supply only Pillar cock 310mm long extended body cast copper alloy with capstan head, chromium plated, fancy type screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (wall hanging two piece pattern) including 'P' or "S" trap, and seat cover with complete all as specified and directed.

S & F in repairs white glazed earthen ware vitreous china wash hand basin of size 550x400mm with and including CI brackets, 32mm bore brass CP waste coupling Inlet/ outlet, PVC flexible pipe, 600mm size for 15 mm bore pipe with brass nut and washers etc complete all as specified and directed.

S&F in repairs vitreous china squatting pan, 'Orissa’ pattern, white of size 580mm x 440mm with integral foot rest, P or S trap (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repairs vitreous chinaware EWC pedestal type closet with white seat & cover with flat bottom with hinging device complete all as specified and directed.

S&F in repairs 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc complete all as specified and directed.

S&F in repairs 15mm brass chromium plated fancy type bib cock with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs 15mm stop valves, fancy type brass chromium plated for iron pipe or for unions and fixed to 15mm bore pipe, complete all as specified and directed.

Supply only 15mm pillar taps, brass chromium plated fancy type with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe or for union and fixed to 15mm bore pipe, complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repairs brass chromium plated, tubular towel rail 20mm dia, D type, 60 cm long between flange complete all as specified and directed.

S&F in repair kitchen sink without drainage board made of stainless steel 1mm thick including supply and fixing 32mm CP waste coupling, plug, washer, 32 mm bore and 60cm long PVC waste pipe including cantilever brackets made of mild steel duly painted with two coats of synthetic enamel paint over a coat of red oxide primer, cutting for and pinning in ends of brackets to errecting stand into wall having bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long complete all as specified and directed.

S&F in repairs chromium plated over head shower 100mm dia round shape single flow (ABS Body chrome plated with Gray face plate) with rubit cleaning system complete all as specified and directed by Engineer in Charge.

S&F in repairs Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed.

M & L stone kerb of roughly squared stones of size 20cmx30cm dressed so that the maximum depression from straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20 mm for the rest of surfaces, jointed in cement mortor 1:6 and struck flush, including embedding stones in the ground to depths indicating and tamping ground around stones and also removing any surplus spoils, etc complete all as specified and directed.

M&L for 60mm thick Machine pressed precast concrete interlocking paver with grey cement and pigment any shape including 25mm sand as screed bed and size conforming to IS 15658-2006, M-25 grade complete all as specified and directed.

M&L for cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) 75mm thick in sub base for interlocking paver blocks, etc complete all as specified and directed

M&L for preparation of new painted surfaces and applying two coat of synthetic enamel on brick, stone, concrete, asbestos cement or plaster surface all as specifed and directed.

Repairing the damp wall by removing the existing putty till plaster level from skirting to the affected aea covering an additional 0.30m distance across all sides of affected area. The smart care hydroloc is applied on plaster by brush ensuring the material goes inside the pores / intersites. The first coat (no dilution) is applied with a forced coverage of 3.7-4.2 Sqm/L area from skirting to the affected area, covering an additional 0.30m distance across all sides of affected area. Allow it to dry for 6-8 hrs. The 2nd coat (no dilution) applied with coverage of 3.7-4.2 Sqm/L perpendicular to first coat. Allow it to dry for 6-8 hrs. After it has dried, water proofing putty is applied. Now the surface is prepared by sand paper to receive the colour over it complete all as specified and directed by Engineer-n-Charge. Note:- Asian Paint smart care Hydroloc Product code 1A76.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, such as manholes cover etc complete all as specified and directed.

S&F mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, inclding cranking, bendiing spirally for hooping for columns, hooking ends and biinding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc for manholes,septic tanks,wells etc not exceeding 10 sqm on plan and not exceeding 1.5m in depth and getting out Hard dense of soil complete all as specified and directed.

Returning, filling in, including, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed stoneware, AC or reinforced concrete), set in cement mortar for 200mm bore of pipe complete all as specified and directed.

M&L Concrete bed to drain pipes 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) including packing under, and haunching against the side of pipes after they are laid and tested for 200mm internal dia of pipe complete all as specified and directed.

M&L for reinforced concrete pipe of 200mm bore of pipe, class NP-2, laid and jointed with collars complete all as specified and directed.

Cuting into existing manholes for connecting new drain making good to pipes and rendering, cutting out existing benching forming branch channel 1/2 round 3/4 section in cement conrete 1:2:4 type B1 smooth finished for 200mm bore pipe complete all as specified and directed.

M&L Rendering 15 mm thick in CM 1:6 on surfaces or surface other than fair face of brick-work or on one side of lathing of stone masionary or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 12 mm thick modified polymer ready mix plaster to Concrete surfaces wall finished even and fair with 3 % of weight of cement WPC, complete all as specified and as directed.

M&L peparation of new surfaces of walls soffits, facia roof and like positions and applying two coat of Exterior weather proof acrylic based paint over a coat of self primer (100% acrylic) etc complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying 1 coat of wall care white putty, 1-2mm thick and further applying 2 coats of oil emulsion distemper over a coat of wall priming paint complete all as specified and as directed.

Preparation of old plastered or unplastered surfaces in walls soffits, facia roof and applying one coat of anti fungal weather proof acrylic based paint 100% acrylic complete all as specified and directed.

M & L for complete removal of existing treatment on walls and applying 1 coat of wall care putty,2mm thick and further applying two coat of oil bound distemper over one coat of primer paint complete all as specified and directed.

M&L for Preparation of old plastered/unplastered surfaces and applying one coat of white wash on ceiling complete all as specified and directed.

S&F 2nd class hardwood 20mm thick clean sawn eaves board fixed with nails or drilling/ screwing in any situation planed both sides and edges tongued (approved design) all as specified and directed by Engr-in-charge.

Removal of paint on steel/ wooden surfaces by applying of paint remover or grinding the surface and making the surface clean and smooth complete all as specified and directed.

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new/ rendered surface works with two or more coats complete all as specified and directed.

M&L for preparing of new wooden surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of Pink primer, as approved complete all as specified and as directed

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors including 15mm thick screed bed of CM 1:4 and pointed with grey cement and no pigment complete all as specified and directed.

M&L Plain Cement concrete 1:2:4 type B-2( 40 mm graded aggregate) 75mm thick as in plinth protection finished even and fair complete all as specified and directed.

S&F in repair 4.8 mm thick Sheet glass,ordinary quality pin headed type and glazing with Aluminium snap beading with rubber Neoprene packing in square exc 0.5 sq. m in each pane complete all as specified and directed.

S&F a layer of black film over glass panes so as to provide a non transparent / opaque finish complete all as specified and directed.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staples/ wooden beading complete all as specified and directed.

Taking down carefully aluminum/copper point wiring (light,fans,socket etc) complete incl battens and fittings such as switch, ceiling rose,light fittings, regulaters, socket etc and making good disturbed surface of wall/floor etc complete all as specified and directed.

M&L for point wring for one light / fan controlled by one switch with 1.5 sqmm nominal area) PVC insulated and PVC unsheathed multi stranded copper conductor cable FRLSH in and including concealed PVC conduit 20 mm dia medium duty ISI marked, including suitable new steel sunken boxes, modular frame and cover plate for fixing of modular switches as per required point in that board, flush to surface for one light point, fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 sqmm copper conductor cable FRLSH connected to common earth duly complete including cutting, chasing the surface and then making good the same in CM 1:6 complete all as specified and directed. (Note : Switches, Sockets etc shall be measured and paid for separately under appropriate items of Sch 'A'

Ditto all as per Item No. 126.00 above but One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sq.mm size complete all as specified and directed.

Ditto all as per Item No. 126.00 above but 5 amps socket outlet on same board board complete all as specified and directed.

Ditto all as per Item No. 126.00 above but One 3 pin socket outlet, 5 Amps,independent borad complete all as specified and directed.

Ditto all as per Item No. 126.00 above but One 3 pin socket outlet with 2.5 sqmm cable for 15 amps switch socket combination outlet on independent board complete all as specified and directed.

Ditto all as per Item No. 126.00 above but one AC Point with 4 sq mm PVC unseathed (FRLS) wire along with 4 sq mm green colour wire as earth contuinity conductor connected to common earth dolly complete all as specified and directed. Note : Seprate circuit of individual point will be drawn from the DB directly for AC Point complete all as specified and as directed.

Supply and Repair/Replacement of Modular switch 1 way 6 Amps, 1 modules 230 volts complete all as specified and directed.

Supply and Repair/Replacement of Modular switch 1 way 16 Amps, 1 modules 230 volts Complete all as specified and directed.

Supply and Repair/Replacement of Modular socket 6A, 2/3 pin combined, 2 modules 230 volts complete all as specified and directed.

Supply and Repair/Replacement of Modular socket 6A/16A, 2/3 pin combined, 2 modules 230 volts complee all as specified and directed.

Supply and Repair/Replacement of five step fan Modular regulator 2 module 230 volts complete all as specified and directed.

M/L and Repair/Replacement for Sub main wiring power/circuit using PVC insulated unsheathed FRLS, stranded copper conductor cable 2 Single core of size 6 Sqmm, earth continuity conductor of size 6 Sqmm to be drawn through in and including PVC conduit concealed in walls/roof/floors complete all as specified and directed. Notes:- (i)Two wires of 6 sqmm and one wire of 6 sqmm & PVC conduit shall be measured as one unit.

M/L and Repair/Replacement for Sub main wiring power/circuit using PVC insulated unsheathed FRLS, stranded copper conductor cable 2 Single core of size 4 Sqmm, earth continuity conductor of size 4 Sqmm to be drawn through in and including PVC conduit concealed in walls/roof/floors complete all as specified and directed. Notes:- (i)Two wires of 4 sqmm and one wire of 4 sqmm & PVC conduit shall be measured as one unit.

Supply and Repair/Replacement of ceiling rose surface backelite 65x50 mm having 3 terminal complete all as specified and directed.

Supply and Repair/Replacement of SPN Sheet metal enclosures with plug and socket with Top and MCB SP 20 Amps including taking down the same complete all as specified and directed.

M&L for taking down and refixing for after Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and as directed.

M&L For breaking the existing wall to make hole for exhaust fan and making good to the disturbed surface of wall complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

Supply and Repair/Replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and Repair/Replacement of LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and Repair/Replacement of Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and Repair/Replacement of Building street light fitting Endura pearl 30W LED lamp new genaration energy saving & environmental friendly long life made up of pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening separate driver compartment with IP65 protection and impect resistance of IK07,with suitable of GI pipe (light grade) bracket and clamps, nut bolts are fixed on wall/post and all as required complete all as specified and directed.

Supply and Repair/Replacement of bell push 6 Amps, 1 modules 230 volts complete all as specified and directed.

Supply and Repair/Replacement of call bell Multi musical type complete all as specified and directed.

Supply and Repair/Replacement of MCB DB Single pole and neutral 12 way double door complete all as specified and directed.

Supply and Repair/Replacement of TP&N distribution board with double door vertical type TPN DB made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating,suitable for MCCB for capacity 100Amp, 16 KA, Incomer 4 ways 415 Volts made up of CRCA sheet with busbar rating 200 Amps Adjustable thermal (70% to 100%) & Fixed magnetic setting type including grouting in the wall, cutting & chasing etc complete all as specified and directed.

Supply and Repair/Replacement of MCB rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SP of 5Amp -32Amp current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and Repair/Replacement of MCB rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN of 63Amp current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and Repair/Replacement of MCCB four pole 415 volts 50 Hz , 63Amps, with rupturing capacity 16 KA complete all as specified and directed.

Supply & Fixing Wall mounted fan white in colour 400mm sweep, 3 in number complete all as specified and directed.

Material and labour for taking out window / split type Air conditioner 1.0Ton / 1.5Ton capacity of any make from its original location, removing the dust from body with blower, cleaning the condenser and cooling coil by using water and caustic soda, painting the base tray with one coat of black enamel paint checking all the connections including functioning of metal clad socket/ DP switch function of relay capacitors overload protector thermostat fan motor blade fan blower drum etc. oiling/ greasing of fan motor checking serviceability and refixing it in its original place including testing commissioning for 1.5/2.0 Ton of AC of any make complete all as specified and directed.

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of 2 TR capacity complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5.0 KVA complete all as specified and directed.

M & L of earthing complete with galvanized steel earth plate electrode of size 600 x 600 x 6 mm thick buried directly in ground to a depth not less than 2.25 mtr below the normal ground level with top edge of earth plate not less than 1.50 mtr below the normal ground level and connected to galvanised earth lead wire 4.0mm dia by means of nut, bolt & washer and protected by 40mm dia GI pipe light grade and watering pipe of 20mm dia GI pipes light grade and connected to earth test point including necessary excavation, earth work, PCC chamber (1:3:6) type C-1 and 40 mm thick RCC pit cover in RCC (1:2:4) type B-1 using 6 mm dia MS round bars @ 150 mm C/C both ways all as shown in electrical plate No. 3 of SSR Part-I complete all as specified and directed.

Supply, laying and testing of in repairs cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and directed.

M & L for sand cushioning for LT cable laid in trenches using screened sand of approved quality as per SSR Part-I complete all as specified and directed.

S & F unreinforced pre-cast concrete cable covers class LV types 2 flat size 250mm x 150mm x 40mm including removal of old covers complete all as specified and directed.

Supply and laying/jointing GI Pipe mideum grade 40mm dia with all fittings laid/fixed on wall/pole or under road/PCC crossing and complete all as specified and directed.

Making connection of PP-R distribution branch with PP-R main of size 50-75mm dia by providing and fixing tee including cutting and making fusion joint etc complete all as specified and directed.

Supply Repair/Replacement Laying and Testing of 3-layer PP-R (Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings and making connection fixed complete to walls, ceilings floors or laid in trenches etc 50 mm dia laid in trenches complete all as specified and directed.

Supply Repair/Replacement Laying and Testing of 3-layer PP-R (Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings and making connection fixed complete to walls, ceilings floors or laid in trenches etc 32 mm dia laid in trenches complete all as specified and directed.

S&F in repair/Replacement of 50 mm dia 3-layer PP-R (Polypropylene random copolymer) Gate valves (brass insert) as per requirement of the site complete all as specified and as directed.

S&F in repair/Replacement of 32 mm dia 3-layer PP-R (Polypropylene random copolymer) Gate valves (brass insert) as per requirement of the site complete all as specified and as directed.

JAY BHARAT METAL SUPPLIERS

SURESH ELECTRICALS

K K Construction Co

BABUBHAI BHIMABHAI PANDAVADRA

SHREEJI ENTERPRISE

Harsh Infrastructure

OM ENTERPRISE