Welcome maint to OMQ at domestic area and Repairs to joinery work in certain bldgs at domestic area under AGE BR-II, GE (AF) No 02 Jodhpur

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

M&L for dismantling floor heart or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises and com[plete all as specified.

Taking down chowkats or frame with shutter (without taking off shutters from the frames) n exc 1.5 Sqm complete all as specified and as directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frames) exc 1.5 Sqm and n exc 4.00 sqm each of any description incl making good the disturbed surfaces complete all as spd and as directed.

Taking down shutters of any description exc 1 sqm & n exc 2 sqm each and refixing in Same opening after doing suitable repairing hinges etc or as directed by Engr-In-charge

Material and labour for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling courses laid and compacted in slope in floor complete all as specified and as directed.

M&L for light coloured Vitrified Ceramic tiles 9-10 mm thick area of each tiles not less than 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:6.

All as per item No. 7.00 above but on vertical surfaces such as dados, skirtings and risers to steps, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone masonry surfaces.

M&L for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick in floors etc. (square/rectangular) area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6

M&L for glazed ceramic tiles, coloured, 350x250x7mm/450x350x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone masonry surfaces.

M&L for preparation of old plastered or unplastered surfaces of walls and applying one coat of white wash.

M&L for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash.

M&L for preparation of old surfaces (plastered or unplastered) of walls including removing/scrapping down existing surface where ever necessary and applying two coat of oil emulsion distemper white or approved tinted including removing existing nails, if any and filling the disturbed / surface, holes/voids with wall care putty/POP to achieve the smooth surface complete all as specified & directed.

M&L for preparationof old surfaces (plastered or unplastered) of walls including removing/scrapping down existing surface where ever necessary and applying one coat (finish coat) of oil emulsion distemper white or approved tinted including removing existing nails, if any and filling the disturbed / surface, holes/voids with wall care putty/POP to achieve the smooth surface complete all as specified & directed.

M&L for preparation of old painted wooden surface of any description not otherwise provided over 10 cm width or girth and applying one coats of synthetic enamel paint and complete.

M&L for preparation of old painted steel surface of any description not otherwise provided over 10 cm width or girth and applying one coats of synthetic enamel paint and complete.

Cleaning and removing all scale dirt etc. from water storage tanks and from mouth of circulating pipes etc. and writing the date of cleaning and next due date for cleaning of tank, capacity of tanks exc. 250 liters and not exc. 500 liters complete all as specified and as directed.

Cleaning and removing all scale dirt etc. from water storage tanks and from mouth of circulating pipes etc. and writing the date of cleaning and next due date for cleaning of tank, capacity of tanks exc. 500 liters and not exc. 1000 liters complete all as specified and as directed.

M&L for poviding and injecting chemical emulsion for post construction anti termite treatment along external wall where the apron is not proving using chemical emulsion at theart of 7.5 ltr per sqm of the vertical surface of the sub structure to a depth of 300mm including excavating channel along the wall and rodding etc complete all as specified and directed.

S&F in repairs, EWC vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device fixed complete all as specified.

S&F in repairs vitreous- China wash down water closet Squatting pan ( Orissa Pattern) size 580 x 440 mm including flush pipe , PVC P-trap and PCC for fixing complete all as specified and as directed.

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, complete all as specified.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mm.

S & F in repairs brass waste coupling of 32 mm dia for WHB all as specified and as directed

S & F PVC waste pipe 32mm bore of suitable length for WHB/Urinsl/sink complete all as specified and as directed

S&F in repair CP soap dish, fixed to plugs with chromium plated screws and all as specified.

S&F in repair CP tubular towel rail, 20 mm dia, D type, 60 cm long between flanges and all as specified

S&F in repair CP grating 100 mm dia all as specified and as directed.

S&F Single mirror bath room cabinet moulded body and frame (made of strong and fine quality A.B.S plastic) with hinged door (size 16"x12"6") white/ivory in colour.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long

S & F sinks with drainage boards made of stainless steel 1 mm thick kitchen or laboratory with plugs,washers and wastes,including bedding in cement mortar o to dwarf wall or including fixing cantilver brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm

Taking up or down steel tubing and connection including cleaning for refixing or removal to store yard of bore 15 mm.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store yard of bore 20 mm.

S & F 15 mm dia galvanized steel tubing, medium grade, with all fitting and fixed complete to walls celling or laid in floors all as specified and directed.

S & F 20 mm dia galvanized steel tubing, medium grade, with all fitting and fixed complete to walls celling or laid in floors all as specified and directed.

S&F in repair stop/gate valves/angle valves cast copper alloy CP fancy type screwed down high pressure with crutch or butterfly handle for 15mm bore.

S&F in repair 15mm bib taps cast copper alloy CP Fancy type with crutch or butterfly handle screwed down for iron pipe or for brass ferrule.

S&F in repair 15mm Pillar taps cast copper alloy, capstan heads CP Fancy type with crutch or butterfly handle screwed down for iron pipe or for brass ferrule.

S&F in repair Brass chromium plated shower rose 125mm size with arm

Dismantling of existing water tank (PVC/RCC/AC) exc 250 ltr but n exc 500 ltr capcity and removing from site complete as directed by Engr -in-charge.

S&F 500 ltr (ISI marked) capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl 20mm bore ball PTMT. valve high pressure with polythyne float and flynut complete in repair.

Dismantling of existing water tank (PVC/RCC/AC) exc 500 ltr but n exc 1000 ltr capcity and removing from site complete as directed by Engr -in-charge.

S&F 1000 ltr (ISI Marked) capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl 20mm bore ball PTMT. valve high pressure with polythyne float and flynut complete in repair.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of 100 mm dia and complete all as specified and directed by Engr-in-Charge.

S&F 75 mm bore UPVC (SWR) pipes type ‘A’, single socketed, in any length with rubber ring joints fixed to walls and complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) door bends 75mm dia with access door and complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR), junction single, (Single T) equal or unequal 75mm with acess door and complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) floor trap with garting of outlet dia 75mm incl jointing with solvent cement and complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints laid in trenches or in floors

S&F PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints fixed in walls and complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR), junction single, (Single T) with acess door 110 mm dia equal or unequal and complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) door bends 110 mm dia with acess door and complete all as specified and directed by Engr-in-Charge.

S&F 110 mm dia PVC WC connector with lip ring complete all as specified and directed by Engr-in-Charge.

Resecuring or easing & adjusting without taking down shutters of any description exc. 1 sqm but n. exc. 2 sqm each and complete all as specified and directed by Engr-in-Charge.

S& F in repairs for 18/19 mm thick prelaminated article board, interior grade, pelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work and complete all as specified and directed by Engr-in-Charge.

S&F in repairs 40 mm dia cupboard knobs of fixed with nut, screw and washer of mild steel, bright finished and complete all as specified and directed by Engr-in-Charge.

S&F in repairs continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps (when open) 30 mm and complete all as specified and directed by Engr-in-Charge.

S&F ball catches with 8mm dia steel ball and brass body and skirting plate including letting in and fixed and complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of old existing surfaces and two layer of wall care putty for smooth surface of wall complete all as specified & directed.

M&L for two coats of oil emulsion distemper , white or tinted, over a coat of chalk whiting smooth putty surfaces of walls all as directed.

S & F structural steel rolled section in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; complete confirming to FE-290(Gde E-165) also fastening and fixing complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

M&L for preparation of new steel surface of any description not otherwise provided over 10 cm width or girth and applying two coats of synthetic enamel paint and complete.

S&F extructed aluminium alloy handles, fabricated type,anodised of size 150mm.

S&F Aluminium anodised barrel tower bolt of extruded section 200mm size

S&F Butt hinges, medium weight cold rolled mild steel of size 100mm.

S&F in repairs extructed aluminium alloy handles, fabricated type,anodised of size 150mm.

S&F in repairs Aluminium anodised barrel tower bolt of extruded section 200mm size

S&F in repairs Butt hinges, medium weight cold rolled mild steel of size 100mm.

S&F in repairs stainless steel curatin rod , high strength MS pipe with powder coated extrusion having outer dia 28 mm including stainless steel fixing brackets all as directed by Engineer-in-Charge.

S&F in repairs Stainless Steel cap for curtain rod for 28mm dia curtain rod as directed by Engineer-in-Charge.

S&F in repairs stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stailess steel wire staples

Welding in repairs exc 2.5 cm & n exc 5 cm in length & thickness of metal n.exc 6 mm all as specified and directed by Engr-in-charge

S&F in repairs floor door stopper, with 150 mm long, of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor.

S&F in repairs 200 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F in solid rubber beading of 30 to 50 mm wide and 3 to 5 mm thick fixing at bottom to existing doors all as directed by Engineer-in-Charge.

S&F in repairs box type hinges of steel window/ventilator, 75/100 mm long including necessary fixing & welding work etc complete all as directed by Engr-in-charge.

S&F in repairs left/right MS handle of steel windows including welding(if required) & fixing complete all as directed by Engr-in-charge.

M&L for hacking out old broken glass (any thickness, size, quality or description) from metal frame glazed with putty including punching or drilling out old glazing pin/spring, clips and providing new ones.

S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty in square n.exc. 0.5 sqm in each paneand complete all as specified.

S&F in repairs for stailess steel kitchen plate rack size-31x30x10 inch , and complete all as directed by Engr-in-charge

S&F in repairs for center hole basin mixer without popup waste system and complete all as directed by Engr-in-charge

S&F in repairs for sink mixer with regular spout w/m and complete all as directed by Engr-in-charge

S&F in repairs for wall mixer with bend, and complete all as directed by Engr-in-charge

S&F in repairs brass chromium plated health faucet of 15 mm bore complete.

S&F in repairs 15 mm bore brass chromium plated two way bib cock two in one with angle cock including fixing to steel pipe or union.

S&F figured glass 4mm thick, pin head type and glazing with oil putty in square n. Exc 0.5 Sqm in each pane complete all as specified & as diretced

M&L for powder coated anodised aluminium frame for door window & ventilator with one or more rebates including joining cleat for fixing etc comlete all as specified.

S&F MS powder coated louvers with including arrangement of fixing glass pinhead as per size & louvers ventilator (Glass shall be measurement separately) complete all as specified and as diredcted.

S&F in repair Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device ,Seat and cover for pedestal pan and complete as directed by Engr-In-charge

Taking down shutter and Refixing in same opening of any description exc 1 sqm & n exc 2 sqm each and complete as directed by Engr-In-charge

Taking down shutters only of any description exc 1 sqm & n exc 2 sqm each and complete as directed by Engr-In-charge

Resecuring or easing & adjusting without taking down shutters of any description exc 2 sqm each complete all as specified and directed by Engr-in-Charge.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and directed by Engr-in-Charge.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars complete all as specified and directed by Engr-in-Charge.

S&F Pressed steel frames of size 125x60mm thickness 1.25mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified.

S&F Pressed steel frames of size 105x60mm thickness 1.25mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified.

M&L for plain cement concrete type B-1 (1:2:4) using 20mm graded cruhed stone agg as in seismic and other similar bands shelves coping bed plates hold fasts plinth courses filling in pressed steel frame and the like finished fair and even incl necessary from work complete all as specified & directed.

S&F framed work such as grills gratings etc with ends of bars shoulders and/or riveted or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings frame work of water tanks and similar works conforming to Fe 290 gde E-165 and complete as directed by Engr-In-charge

S&F 35 mm thick factory made, second class hard wood, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in-Charge.

M/L for Glazed and skeleton shutters of thickness 35mm of IInd class hard wood , open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of doors shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats note: Glazed or clothetc in panelsor sash square shall be measured seperately complete all as specified and directed by Engr-in-Charge.

S/F Flush shutters, 30 mm thick paticle board core construction, with block board core and plywood face panels, commercial type on both sides and complete as directed by Engr-In-charge

M&L for preparation of wooden surface of any description not otherwise provided over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer and complete all as specified and directed by Engr-in-Charge.

S&F Stainless steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed by Engr-in-Charge.

S&F Aluminium anodised barrel tower bolt of extruded section 150mm size complete all as specified and directed by Engr-in-Charge.

S&F in repairs Aluminium anodised barrel tower bolt of extruded section 150mm size complete all as specified and directed by Engr-in-Charge.

S&F in repair curtain rod, stainless steel, chromium plated with fixing brackets, stops, rollers etc of 25mm bore complete all as direcred by Engr-in -Charge.

S&F in repair stainless steel decorative end cap suitable for 25mm dia curtain rod as per approval by Engr-in-Charge.

S&F in repairs stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-in-Charge.

Welding in repairs exc 2.5 cm & n exc 5 cm in length & thickness of metal n.exc 6 mm all as specified and directed by Engr-in-charge

S&F in MS peg set with 3 to 5 hooks fixed to doors/wall with screws complete all as specified and directed by Engr-in-Charge.

S&F in repair MS 300 mm , ordinary rat tail rod pattern springs including rooler and roller plate complete all as specified.

S&F 40 mm dia cupboard knobs of fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed by Engr-in-Charge.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps (when open) 30 mm complete all as specified and directed by Engr-in-Charge.

S& F for 18/19 mm thick prelaminated article board, interior grade, pelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work and complete as directed by Engr-In-charge

M&L for second class hard wood plain fillets, of sectional area n. exc. 3 sqcm, rectangular or triangular in section, clean sawn, bull nosed, splayed, chamfered or rounded on one edge or face secured with nails or brads and complete as directed by Engr-In-charge

S&F rolled mild steel of grade Fe-290 (Grade E-165) in rolled section as in frames for doors/windows, framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc and complete as directed by Engr-In-charge

M&L 6mm plywood grade BWP type BB fixed with screw timber frame work and complete as directed by Engr-In-charge

Bansal Enterprises

JAMWAY MATA CONSTRUCTION COMPANY

psj build solutions and company