8166/GE/SMB/T-14/2026-27 REPAIR MAINTENANCE OF WATER SUPPLY PIPE LINE MOTOR PUMPS AND LOWERING LIFTING OF SUBMERSIBLE PUMPS DOSING PUMPS AND CONNECTED WORKS AT GE SAMBA AT AP I AP II PAREL LINE BHIM LINE MES COLONY UNDER GE SAMBA

All as per item No 1 above but of size 200/150mm dia

All as per item No 1 above but of size 80/100mm dia

All as per item No 2 above but of size 100/80 mm dia

All as per item No 2 above but of size 40/50mm dia

All as per item No 2 above but of size 15/20/25mm dia

M&L for repair rusted /damaged portion of acoustic enclosure by replacing the ms sheet , change of hinges ,door locks , door catch of DG set of any capacity/size of complete including painting of DG Set sspray painting machines with one quote of synthetic enamel paint matching to exisitng colour duly scraping out old rusted surfaces complete all as specified and directed.

M & L in replacement D I (Ductile iron pipes with spigot and socket ends Class 'K'-7, 250mm dia including all fitting ie, bend of any type ,tee , reducer etc laid in trenches, complete all as specifed and directed.

M & L in replacement D I (Ductile iron) pipes with spigot and socket ends Class 'K'-7, 200mm dia including all fitting ie, bend of any type ,tee , reducer etc laid in trenches,complete all as specifed and directed.

M & L in replacement D I (Ductile iron) pipes with spigot and socket ends Class 'K'-7, 150mm dia including all fitting ie, bend of any type ,tee , reducer etclaid in trenches,complete all as specifed and directed.

M&L for painting of LT Panel board after repairing the old rustusted / damaged portion of the panel board by replacing the ms sheet , change of hinges ,door locks , door catch of any type and size by spray painting machine with one coat of synthetic enamel paint matching to existing colour duly scraping out old rusted surfaces complete all as specified and directed.

M&L for PCC 1:2:4 type C1 (using 20 mm graded granite stone aggregate) as in coping, including necessary form work complete for supprot pillar for resting pipe in the location excavation not possible all as specified and directed

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep soft/loose soil getting out for laying of pipe CI/GI etc of any size, complete all as specifed and directed.

Returning filling in including spreading leveling watering and well ramming in layers not exc 25cm complete all as specifed and directed.

Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point, complete all as specifed and directed.

CI/GI special fittings as per IS for spigot and socketed pipes for water mains / branches lines such as bends (any type radious and angle ) tapers any type (straight, bend,increasing,decreasing,or double socket etc) tee pices,single branch ,Y juntion, double branch,cross(all socket ,socket and spigot) collers,caps & plugs, including connecting pieces one end flanged and other socket or spigot and bell mouth pices suitable for run lead joint, run lead up to 150 mm bore complete all as specified and directed.

M&L for drain out water/dewatering the tank with portable submersible pump from Over Head Reservior (OHR) of capacity 0.50 Lakh Gallons at 21 mtr height from ground and cleaning of wall, ceiling and floor by high pressure water jet and remove the sludge / mud thoroughly, clean inner surface of the tank and wash out by flushing with clean water and drain out.Treatement of inside tank by exposing UV radiation to kill further suspended or floating bacteria, if any complete all as directed by Engr-in-Charge.

All as per item No. 14 here in before but capacity 0.20 lakh Gallons at 21 mtr height

All as per item No. 14 here in before but for semi/underground sump of capacity 1 lakh Gallons.

All as per item No.14 here in before but for semi/underground sump of capacity 0.5 lakh Gallons.

All as per item No. 14 here in before but for semi/underground sump of capacity 0.2 lakh Gallons.

S&F sluice valve cast iron body, double flanged and drilled, 80 mm bore as per IS- 14846, class PN-1.6, long body type with SS spindle etc with all fittings, jointing materials etc including taking down old unserviceable sluice valve complete all as specified.

All as per item No.15 here in above but 100 mm bore

All as per item No.15 here in above but 150 mm bore

All as per item No. 15 here in above but 200 mm bore

All as per item No. 15 here in above but 250 mm bore

S & F non return valve cast iron flanged both end installed on 80 mm dia CI pipes including taking down old unsv non return valve complete all as specified and approved by EIC.

All as per item No.16 here in above but 100 mm bore

All as per item No.16 here in above but 150 mm bore

All as per item No. 16 here in above but 200 mm bore

All as per item No. 16 here in above but 250 mm bore

M&L for preperation of outer surfaces of OHR of capacity 0.50 LG, height 17-25 mtr from ground including staging and connected items such as inlet, outlet, overflow pipes, sluice valves, NRV, Air valves, gate valves, MS other articles such as bracing/ brackets etc, ladders, grills, and all other connected items within the fencing of OHR and painting of OHR with two coats of exterior emulsion paint including staging and two coats of synthetic enamel paint to all the MS/CI/DI articles such as inlet/outlet, overflow pipes and connected valves brackets etc. Note:- Preperation includes rubbing, scrapping, filling of putty and repaire to minor cracks/ joints with cement plaster. Required T&P shall be contractor's own arrangement.

All as per item No. 17 here in before but capacity 0.20 lakh Gallons at 21 mtr height

All as per item No. 17 here in before but for semi/underground sump of capacity 1 lakh Gallons.

All as per item No.17 here in before but for semi/underground sump of capacity 0.5 lakh Gallons.

All as per item No. 17 here in before but for semi/underground sump of capacity 0.2 lakh Gallons.

M&L for construction of brick masonnary with full brick wall chamber size of 1200x1200x1200mm internal diemension with earth work on any type of soil , PCC M-10 type C-2 as in foundation , brick work in CM1:4, 15mm thick plaster in CM1:4 internaly and externally , flush pointed in same mortar as work proceeds , 75mm thick PCC coping all around (M-15 with 20mm aggregate ) , flooring shall 40mm thick PCC M-15 (Nominal Mix ) laid over 75mm thick hard core. Top cover shall be made out of 3mm thick MS sheet fixed in angle iron frame made out of angle iron size 40x40x6mm with two numbers of hinges on one side and locking arrangement at other side complete including painting with two coats of synthetic enamel paint over a coat of redoxide primer complete all as specified and directed including demolation of old existing Abandoned valve pits.

All as per item No. 18 here in above but size 1000x1000x1000 mm

All as per item No. 18 here in above but size 900x900x900 mm

All as per item No. 18 here in above but size 600x600x600 mm

M & L for removing vegitation, grass, scrubs,treaming of tree branches, creepers and bushes growing in pump houses area, sub station yardfrom inside /outside , around the pipe line poles/stays,drainge ,valve chamber, roof of pumphouse etc,along with fancing by mannually / mechanically and keep the pump house yard/ sub station yard neat and clean complete all as specified and as directed. Note :- Unit rate quoted deemed to include to keep the installation neat and clean through out the period of contract and each Job of cleaning /Pumps house installation will be measured and paid.

Cutting existing GI/CI water main pipe line 250/200mm bore of pipe in position for making branch connection (insertion of GI/cast iron Tee,ferrul joint ) including excavation and earth work complete all as apecified and directed. Note : GI/CI fittings such as tee, bends, collar, reducer etc joint and jointing material for fixing of cast iron fittings shall be measured and paid separately.

Cutting existing GI/CI water main pipe line 150/100/80mm bore of pipe in position for making branch connection (insertion of GI/cast iron Tee,ferrul joint ) including excavation and earth work complete all as apecified and directed. Note : GI/CI fittings such as tee, bends, collar, reducer etc joint and jointing material for fixing of cast iron fittings shall be measured and paid separately.

Designing, Supplying, Fixing, Installing, Testing and Commissoning of LT panel board INDOOR type feeder pillar duly febricated by CPRI approved manufacturer, of suitable size, metal clad, floor mounted vertical indoor cubical type made of not less than 2 mm thick CRCA sheet and (40x40x6) mm angle iron frame and supports, front opening type double door, protection class IP-54, duly powder coated after seven tank process, for fixing switches for LT 3 phase 450 Volts 50 C/s and key type locking arrangements with electrolytic grade Aluminium bus bar of 200 Amps capacity of four poles, with all standerd switchgear and protection, internal wiring of adequate size with PVC insulated multi stranded copper conductor cable, fixing over PCC (1:2:4) type B-1 using 20 mm graded stone aggregate foundation, including complete all as specified and comprising and including of following:- (i) MCCB 4 Pole 25 KA, 440 Volts, 3 phase 4 wire125 Amps capacity with thermal magnetic release mechanism = 01 No (incomer). (ii) Air insulated PVC Sleeved Aluminium bus bar 200 Amps capacity with necessary colour coding in seperate steel sheet enclosure. = 04 Nos strip. (iii) MCCB 4 pole 16 KA, 440 Volts, 3 phase, 4 wire 63 Amps capacity with thermal magnetic release mechanism = 02 Nos (outgoing) (iv) MCCB 4 pole 16 KA, 440 Volts, 3 phase, 4 wire 40 Amps capacity with thermal magnetic release mechanism = 02 Nos (outgoing)

(v) Digital Electronic meter shows Amps /Voltage as per phase as per rated capcity of bus bar =05 Set. (vii) Neon indicator lamp Red/yellow/Blue colour = 04 Sets. (viii) Star delta starter with phase preventor for 25 HP motor -02 (ix) Star delta starter with phase preventor for10 to 15 HP motor -02 Note:- LT panel size should meet the requirement of housing all the switchgears and accessories, and panel shall be installed on PCC foundation and two Nos earth connection point at both side of the panel needs to be provided.

Designing, Supplying, Fixing, Installing, Testing and Commissoning of LT panel board INDOOR type feeder pillar duly febricated by CPRI approved manufacturer, of suitable size, metal clad, floor mounted vertical indoor cubical type made of not less than 2 mm thick CRCA sheet and (40x40x6) mm angle iron frame and supports, front opening type double door, protection class IP-54, duly powder coated after seven tank process, for fixing switches for LT 3 phase 450 Volts 50 C/s and key type locking arrangements with electrolytic grade Aluminium bus bar of 600 Amps capacity of four poles, with all standerd switchgear and protection, internal wiring of adequate size with PVC insulated multi stranded copper conductor cable, fixing over PCC (1:2:4) type B-1 using 20 mm graded stone aggregate foundation, including complete all as specified and comprising and including of following:- (i) MCCB 4 Pole 50 KA, 440 Volts, 3 phase 4 wire 400 Amps capacity with thermal magnetic release mechanism = 01 No (incomer). (ii) Air insulated PVC Sleeved Aluminium bus bar 600 Amps capacity with necessary colour coding in seperate steel sheet enclosure. = 04 Nos strip. (iii) MCCB 4 pole 16 KA, 440 Volts, 3 phase, 4 wire 80 to 100 Amps capacity with thermal magnetic release mechanism = 04 Nos (outgoing) (iv) MCB 4 pole 10 KA, 230 Volts, 1 phase, 63 Amps

(v) Digital Electronic meter shows Amps /Voltage as per phase as per rated capcity of bus bar . - 05 Set (vii) Neon indicator lamp Red/yellow/Blue colour = 04 Sets. (viii) Star delta starter with phase preventor for 40 HP motor -04 Note:- LT panel size should meet the requirement of housing all the switchgears and accessories, and panel shall be installed on PCC foundation and two Nos earth connection point at both side of the panel needs to be provided.

S & F foot valve valve cast iron flanged both end installed on 80 mm dia CI pipes including taking down old unsv non return valve complete all as specified and approved by EIC.

All as per item No.26 here in above but 100 mm bore

All as per item No.26 here in above but 150 mm bore

All as per item No. 26 here in above but 200 mm bore

M&L in repair 15 MM thick plaster in one layer in CM 1:4 on concerete /Fair faces of brick surface ,with surface finished fair & even for valve chamber complete all as specified and directed

S&F MS work for as in doors of angles or other section with gusset plate rails ,bracesetc. Complete drilled for fixing of steel doors etc.to be prepared for valve chamber cover & Frame.

M&L for painting of various coloured old/New CI/GI pipe line of various sizes,motor and pumps , at Pump houses with syentheic enamel paint after removing/ scratching old painted surface incl preparation of surface complete all as specified and directed .

Supply and installing of size 150mm x50mmx6mm thick of perforated painted with powder coated MS cable tray with perforation not more than 17.5 % in convinient section ,joined with connectors suspended from ceiling with ms suspenders, nuts bolts , fixed on wall /floor all as specified and directed .

M&L for fabrication, erection, testing, and commissioning of glow sign board of size 8'x3'x6" made of GI sheet 24 gauge, aluminium channel/angle as beading, 2 mm poly carbonated sheet, 40 mm polyvinyl sheet with computerised letter cutting, including three nos 4'x20 watt LED light fitting and fixtures with suitable wiring, lettering as under & fixing a logo of core of Engrs of suitable size as directed including grouting with angle iron frame on RCC slab etc complete and all as directed:- MILITARY ENGINEERING SERVICES PH - 07 MES COLONY GE SAMBA, J & K MILITARY ENGINEERING SERVICES OLD BOOSTER PUMP HOUSE GE SAMBA, J & K MILITARY ENGINEERING SERVICES PUMP HOUSE NO -09 CHOPRA LINE GE SAMBA, J & K

M&L for fxing in repair alluminim thimble of cable of size 50 sqmm to 95 sqmm

M&L for painting of various coloured old/New CI/GI pipe line of various sizes,motor and pumps , Pressure filter tanks at swimming pool of syentheic enamel paint after removing/ scratching old painted surface incl preparation of surface complete all as specified and directed .

M & L for Isolate/de-energize the supply to the LT Panel Board/feeder pillar box of different rating capacities, 415 Volts/230 Volts, opening the doors/covers of the cubicle enclosure for carrying out the servicing/maintenance/repairs of the Panel Board, switch gear, metering including carrying controle wiring with new cable PVC insulated, stranded copper conductor 2.5 sqmm incl new copper lugs and nuts, bolts, washers complete all as specified and directed etc and re-fixing the same in place after repairs including testing and commissioning of the panel board :- (i) Cleaning the inside switch gear chambers for removing dust, carbon and rusted surfaces including cleaning with blower and apply insulating varnish. (ii) Check the condition of the insulators including cleaning for and replacement of insulators if required. (iii) Tightening up of all bus bar connections, cable connections, replace bolt, nuts wherever required.

S&F in repair MCCB , 4 pole, 250 Amps, 36 kA, 415 Volts, 50 Hz, AC and taking out existing old unserviceable MCCB including electric connection & testing complete all as specified and as directed.

All as per item No. 35 here in before but 200 Amps 25 KA

All as per item No.35 here in before but 160 Amps 16 KA

All as per item No. 35here in before but 125 Amps 16 KA

M&L for supply and lay in trenches GI tubing medium grade with necessary fittings such as bend, tee,elbow etc complete of size 15 mm bore including taking down old unserviceable GI tubing complete all as specified and directed by EIC.

All as per item No. 36 here in above but 20 mm bore

All as per item No. 36 here in above but 25 mm bore

All as per item No. 36 here in above but 40 mm bore

All as per item No. 36 here in above but 50 mm bore

All as per item No. 36 here in above but 80 mm bore

All as per item No. 36 here in above but 100 mm bore

All as per item No. 36 here in above but 150 mm bore

Supply and fix in repair of gun metal gate valve with crutch or butterfly handle screwed both end for iron pipe of 15 mm bore including old unserviceable gate valve complete all as specified and directed by EIC.

All as per item No. 37 here in above but 20 mm bore

All as per item No. 37 here in above but 25 mm bore

All as per item No. 37 here in above but 40 mm bore

All as per item No. 37 here in above but 50 mm bore

S & F PVC sheated multistranded copper conducter cable size 35 sqmm single core 1100 Volts for connection from MCCB Motor starter ,Motor connection to be made with cable terminal lugs ,complete all as specified and directed.

All as per item No 38 but of size 70 Sqmm.

Supply & Fixing Star delta starter with safety control i.e single phase prevenetor, thermal over load relay , low voltage coil,analylog meter having by pass capacity switch , star detla delay timer suitable for 75 HP MU-G75 FASD centrifugal pump including taking down existing starter, complete all as specified and directed.

All as per item No 39 above but suitable for 10 to 15 HP submersible pump ,model MU-G30 FASD i

All as per item No 39 above but suitable for 20 to 25 HP submersible pump ,model MU-G50 FASD.

Labour only for lifting /taking up of defective submersible pumping set of capacity 10HP to 25 from deep borewell and dismantling of connected rising main i.e. non return valve, bend etc from delivery of pump set, lifting of column pipe of size up 100mm dia mm dia fixed with pumping set, unscrewing of column pipes from socket / flange cutting of welded strip unscrewing of cable holding clamps and disconnecting of submersible cable joint complete all as directed by EIC.

Labour only for lowering of submersible pumping set of capacity 10HP to 25 after repair and testing in deep bore well not less than 90 mtr below the ground level including lowering of column pipe size 150 mm dia by screwing with socket/flange welding or fixing MS strips, fixing of cable clamps etc up to the maximum depth of 150 mtr all as directed by EIC. Note: (iii) Contractor shall caution his staff during execution to take maximum precaution while lifting/lowering the pump set at site. In case any accident/injuries occurs the department will not held responsible for any miss happening due to negligence on their (workers) parts. Contractor shall be held totally responsible and all penalty /damages on this account shall be born by the contractor.

M&L in repair for overhauling of submersible motor 10 HP to 25 HP AC 3 phase by dismantling , opening into parts cutting of burnt winding, cleaning of slots, balancing of rotor, cleaning polishing and rewinding with same gauge of PVC insulated copper wire & testing all as specified & directed by Engr-in-Charge. Note : Spare parts shall be measured & paid separately

Supply only Thrust plate suitable for 10 HP to 25 HP submersible motor as per existing type and size.

Supply only Thrust pad suitable for 10 HP to 25 HP submersible motor as per existing type and size.

Supply only Bearing bush lower suitable for 10 HP to 25 HP submersible motor as per existing type and size.

Supply only Bearing bush upper suitable for 10 HP to 25 HP submersible motor as per existing type and size.

M&L in repair for overhauling of submersible pump of 5 to 9 stage not less than 1500 LPM, dismantling the pump, repair/ overhauling complete and reassembling after repair, transportation back to pump house including replacing the parts: Note: Spare parts will be measured and paid separately

Supply only Impeller bronze suitable for 5 to 9 stage submersible pump as per existing type and size.

Supply only Stage sleeve suitable for 5 to 9 stage submersible pump as per existing type and size.

Supply only Neck ring suitable for 5 to 9 stage submersible pump as per existing type and size.

Supply only Running bush suitable for 5 to 9 stage submersible pump as per existing type and size.

Supply only Sand guard suitable for 5 to 9 stage submersible pump as per existing type and size. Note : All repair work and spare parts from item No 40 to 50 shall be carried out from authorized dealer /approved firms as approved by the EIC and submit purchase voucher in this regard

Supply and fixed in repair Submersible cable PVC insulated, multi stranded, copper conductor 3 core, 35 sq mm flat, 1100 volt grade completed all as specified , Make :- Finolex /Plaza / Asian cable

S&F of Cable jointing kit ( compound ) suitable for submersible cable of size up to 50 sqmm 3 core, Make :- (Denson/M.seal)

S & F in replacement dosing system containg the pump of capacity 6LPH @4 bar -PP-single RPMphase 230volts ,Agitator -low speed -worm gear box with motor capacity 0.5HP RPM 100 ,1440 RPM ,3 phase 415 volts Make of motor : CG , wetted part of motor /agitator in SS -304 ,,height of -550mm ,shaft dia 22mm ,impeeler -propeller ,impeller dia 180mm including 100ltr LDPE tank with monting stand for fixing the completed syatemincluding foot valve cum stainer , injection valve all as specified and directed .

M & L for complete checking of Starter Panel/Pump Sets, cleaning and servicing, tighting the nut bolts, cable joints, checking of conntactors, relays, aluminium/cu lugs, and rectified the minor defects to make it serviceable condition including replacement of unserviceable spares and testing complete all as specified and as directed by Engr In Charge

Note:- The contract sum shall be arrived at after deduction of amount of Sch of credit.

Please Enable Macros to View BoQ information