Work of Construction of new sump pump house at residential colony at 132 kv S/s Majra, Dehradun

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth, 1.5 m in width as well as 10sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as 2.6.1 All kind of soil

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shaps and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) DSR-ITEM NO- 6.4.2

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering – All work up to plinth level : (DSR 4.1.3) 1:2:4 (1cement : 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size)

Steel reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete upto plinth level (DSR 5.22.1) Mild steel and medium tensile steel bars

Reinforced cement concrete work in proportion 1:1.5:3 (1cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) inwalls (any thickness), including attached pilasters, buttress, plinth and string courses, fillets, slabs, lintels, columns, pillars, abutments, posts and struts etc. upto floor five level excluding cost of centering, shuttering, finishing and reinforcement (DSR-5.2.2)

15 mm cement plaster on rough side of single or half brick wall of mix : (DSR 13.5.1) 1:4 (1cement : 4 coarse sand)

Providing and fixing of GI pipes of 100 mm heavy class including all fittings like couplings bend, Tee, elbows, flanges etc welding/threaded joints and laying under ground under 1 mtr depth including 4mm thick bituman sheet wrapping coating as required including excavation of soil and back filling with proper arrangement (PTCUL schedule)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete for fixing of motor with pump at sump house including fixing the same providing of all labour and T&P DSR 10.2

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, parking shade balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.10.26.1

Supply and fixing of 12.5 HP sludge/sewage pump 100 mm suction and 100mm delivery Kirloskar/Crompton/ABB and equivalent make as approved by engineer in charge including drilling cutting holes and proper alinment wiring up to control panels with all cost of material and T&P required for proper completion of work. (PTCUL shedule)

Supply and fixing of 3 phase motor starter(pump controller) suitable for 12.5 HP dewatering pump. (Market rate)

Work of providing and lying of 6mm submersible copper 4 core cable including providing PVC pipe, and connect to starter including complition of all work and providing of all labour and T&P (ptcul shedule)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc.DSR-ITEM NO.-9.48.2

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. (40 mm thick with 20mm nominal size stone aggregate).(DSR-11.3.1)

Providing corrugated G.S. sheet roofing including vertical / curvedsurface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpetwashers filled with white lead, including a coat of approved steelprimer and two coats of approved paint on overlapping of sheetscomplete (up to any pitch in horizontal/ vertical or curved surfaces),excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.(DSR12.1.1 )0.63 mm thick with zinc coating not less than 275 gm/m²

m/s star power solutions

Mamtainfra Power

M/s Singhal and Co