REPAIRS TO ROOFING, CEILING, WALL PANELLING AND JOINERY IN ARMY BUILDINGS AT SHARIFABAD UNDER AGE (I) CIF (K) AT SHALATENG GARRISON.

Amount

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering, complete all as specified.

0.63 mm thick, galvanized, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roofs,walls etc with grade of zinc coating 275 grams per square metre complete all as specified.

0.80 mm thick plain , galvanised , mild steel sheeting , in ridges, hips, valley gutters, drip and straight flashing ( length and girth as fixed ) with grade of zinc coating 275 grams per square metre complete all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated profile steel sheet 0.50mm thick of colour as approved by AGE(I), having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by AGE(I), having tensile strength of 550 Mpa as in roof covering/cladding to ridges, valley gutters etc. fixed with self tapping screws complete all as specified.

2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with 'L'' or ''J '' type bolts including necessary bitumen washers as in roof, wall etc , complete all as specified.

Preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete primer complete including preparing new zinc (or galvanized) surfaces to receive painting by coating with mordant solution including washing and cleaning etc., complete all as specified.

Dismantling structural steel work ,wrought iron or mild steel work but excluding frame work of any description not otherwise provided for , complete all as specified.

Rolled mild steel work in main and cross beams, hip and jack rafters; purlins where connected to comman rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, conforming to Fe-410-0 or Fe-310-0, complete all as specified & directed.

Steel tubular /Square section roof trusses ( framed) trusses, sun shades , purlins and fastening including distance pieces etc. with special shaped washers etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 all as specified and directed by Engineer-in-Charge.

Dismantling wall and ceiling board (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified.

8mm thick laminated wooden wall panelling interlocking type fixed with nails to timber frame work complete all as specified and as directed by Engineer-in-Charge. Note : The pattern and colour of panelling shall be approved by AGE (I) and contractor shall not have any claim whatsoever on this account.

Providing and fixing of false ceiling at any height of 595 x 595 x 9 mm thick Gypsum ceiling tiles fixed to anodised aluminium snap grid frame work for false ceiling, securely fixed to the structural soffit by approved hangers at 1200mm maximum centres. Hangers of (GI wire 4mm dia) to be fixed by approved roof plug, level adjustment and screws etc., complete all as specified and directed by Engr-in-Charge.

Dismantling timber scantling 40 Sq cm and over in section in any position, framed work, complete all as specified and directed by Engr-in-Charge.

2nd class soft wood (Kail) as in scantling, clean sawn timber, fixed in framed work, complete all as specified.

Plain fillets of 2nd class soft wood (Kail), square, rectangular or triangular in section, wrought, secured with nails or brads of sectional area exc 6 & not exc 13 sq.cm, complete all as specified & directed.

Plain fillets of 2nd class soft wood, square, rectangular or triangular in section, bullnosed, splayed, chamfered or rounded on one edge or face, secured with nails or brads of sectional area exc 13 & not exc 25 sq.cm, complete all as specified & directed.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area n.exc 1.5 Sqm each including cutting holes for taking out hold fasts, dismantling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n.exc 4 Sqm each including cutting holes for taking out hold fasts, dismantling brick work (holes cut and any other damages to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified.

Taking down shutters of any description not exceeding 1 square metre each complete all as specified.

Taking down shutters of any description exceeding 1 square metre not exceeding 2 square metre each complete all as specified.

2nd class hard wood (Hollock/Sal/Kalasiris) plain, solid straight chowkats,and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints supplied and fixed complete, all as specified and as directed.

30mm thick flush shutter solid core construction, with particle board core and plywood face panels , commercial type on both side and fitted to chowkats, complete all as specified and directed.

Factory made, 35 mm thick 2nd class soft wood (Kail) glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part -I. section 8, clause 8.24(a) for doors etc are provided with stiles and rails, complete all as specified.

Factory made, 30mm thick, 2nd class soft wood (kail), glazed and skeleton shutters for windows/ventilators, open rebated and prepared to receive glass or gauge etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, size of members of shutters as specified in clause 8.24 (b) of SSR Part-I, fitted to chowkat, are provided with stiles and rails, complete all as specified.

Factory made, 30 mm thick 2nd class soft wood (Kail) glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, sizes of members of shutters as specified in SSR Part -I. section 8, clause 8.24(a) for windows, ventilators etc are provided with stiles and rails, complete all as specified.

Anodised aluminium powder coating (Thickness of powder coating not less than 50 microns) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

Anodised aluminium powder coating (Thickness of powder coating not less than 50 microns) door shutters, aluminium section weighing 0.55kg/m including 5mm thick sheet glass and necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 No's in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified.

Anodised powder coated of any colour aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including 5mm thick sheet glass and necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

Anodised aluminium two track sliding windows of medium grade section weighing 0.55Kg/RM (each panel n. exc. 0.6 x 1.2m size) including necessary jointing cleats, glazing clips, rubber gasket, aluminium snap beading, screws, aluminium frame and fittings including 5mm thick sheet glass handle 2 Nos in each window, hinges all as manufacturer's instructions, complete all as specified.

Butt hinges, medium weight, cold rolled, mild steel 100 mm long (ISI marked), complete all as specified.

Butt hinges, medium weight, cold rolled, mild steel 50 mm long (ISI marked), complete all as specified.

Extruded aluminium alloy handle, fabricated type, anodised, 150 mm long (ISI marked), complete all as specified.

Extruded aluminium alloy handle, fabricated type, anodised, 100 mm long (ISI marked), complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 200 mm long (ISI marked), complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 150 mm long (ISI marked), complete all as specified.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or excluded sections and fixing bolts and sliding bolts of excluded sections or cast aluminum alloy and fixed, 300 mm long, complete all as specified.

Ist class soft wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified.

300mm ordinary rat tail rod pattern door spring including roller and roller plate of mild steel, complete all as specified.

Mild steel galvanised wire cloth 0.40mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks, wire staples or beading etc, complete all as specified.

Preparation of new or previously untreated wood or wood based surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified.

Preparation of old painted wooden or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified. Note:- Credit schedule has been given separately under tender documents and shall be adjusted in general summary by the deptt. for arriving at net contract sum.

M/s GHULAM HASSAN MIR

M/S SHIMAR STAR GLACIER

M/S Wani Associates