Turnkey Contract for Survey Design Supply Installation Testing Commissioning of the Work of Undergrounding Strengthening of HT and LT Electrical Network on Arterial Roads of Dehradun Town EDC Urban South division

SCHEDULE A1 : 33 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES

POWER CABLES AND ACCESSORIES

19/33 KV (E) grade, Al conductor, Tr-XLPE insulated, Cu tape screened, armoured, PVC sheathed power cable : 3-core/ 400 Sqmm (Colour of Outer sheeth of Cable shall be different from 11 KV & LT cable as specified by UPCL)

Termination kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR / heat-shrinkable type including screen and armour earth kits, all accessories and lugs.

33 KV Premoulded screen connector suitable for 36 KV RMU for rating 1Rx3Cx400 sq.mm. as per RMU OEM recommendation

B-Class medium duty GI pipe 150 mm - as per IS 1239 including coupling

33 KV 630A 25 kA/1 sec Outdoor Motorized SF6 insulated Ring Main Unit with 3 nos. VCB Module as incoming/ outgoing (VVV) including auxiliary power transformer, SCADA compatible and with suitable provisions with to connect with FRTU.

Concrete route marker for HT cable having emboss " DANGER UPCL 33 KV CABLE BELOW" and directional arrows

SUPPLY OF MATERIAL FOR CABLE JOINT PITS / INSPECTION CHAMBERS (64 Nos)

Straight through jointing kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated , screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

Galvanised M.S. Channel 125x65x6 mm. (for frabrication of lid support mesh structure)

Duct sealing material / kit for duct dia 160 mm, sealing length upto 15 cm with expanding polyurethane filler or other sealant material suitable for PVC / HDPE sheathed cables .

SUPPLY OF MATERIAL FOR OVERHEAD GRANTRY AT SUBSTATION

Supply of material for Cable riser at OH structure/Gantry (10 Nos)

Galvanised M.S. Channel 100x50x6 mm.

Galvanised MS Angle 65x65x6 mm.

33 KV Polymer Pin Insulator with GI pin

GI clamps and cable cleat of suitable size for clamping HDPE pipe of OD 160 mm. for holding HT cable on 33 KV Gantry & Line isolator

GI E Clamp for 33 KV Pin insulator

33kV, 10kA Lightning Arrester, distribution class with earth lead disconnector

GI Earthing Strip 50X6MM (for earting HT cables and RMUs)

Tinned Copper braid of size 50x6x1000 mm. with end lugs (for earthing of HT cable and RMU)

Supply of material for New Terminal Gantry at SUB-STATION (02 Nos)

R.S. Joist 175x85 (Grade E250-A, IS:2062)

R.S. Joist 175x85 for top (Grade E250-A, IS:2062)

Galvanized M.S. Angle 50x50x6 mm.

Galvanized M.S. Channel 100x50x6 mm (for LA)

33 KV Disc Insulator 70 KN, B & S Type

Disc fitting for Dog 70 KN

33kV, 10kA Lightning Arrester, Station class with all accessories and mounting hardware

Chrome plated M.S. bolt & nut with washers.

Stone pad 300x300x75 mm.

MS plate 225x225x8 mm thick

SUPPLY OF MATERIAL FOR 33KV BAY CONSTRUCTION OR UPGRADATION (01 No)

Supply of material for Line isolator (for 01 Bay + 01 addl line isolators)

Line Isolator, 800A, 33KV, triple pole single throw manually operated

Galvanized M.S. Channel 125x65x6 mm

Galvanized M.S. Angle 75x75x8 mm

Galvanized MS Angle 50x50x6 mm.

Galvanized M.S. flat 50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for Bus Isolator

Bus Isolator, 800A, 33KV, Triple pole, single throw, manually operated

Galvanized M.S. Channel 125x65x6 mm

Galvanized M.S. Angle 75x75x8 mm

Galvanized M.S. Angle 50x50x6 mm.

Galvanized M.S. flat 50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for 33KV VCB

33 KV, 1250A, 3 Phase outdoor type VCB, 24 V DC including GI mounting stand

Supply of material for Sets of Outdoor CT

33 KV Single Phase, Multi Core CT, Outdoor type, CTR 600-300/1-1-1 A

Junction box for CT

Galvanized M.S. Channel 125x65x6 mm

Galvanized M.S. Angle 75x75x8mm

Galvanized M.S. Plate 400x400x8 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for Bus Bar Gantry Structure

R.S. Joist 175x85x6 mm. (Grade E250-A, IS:2062)

R.S. Joist 175x85x6 mm. for top (Grade E250-A, IS:2062)

Galvanized M.S. Angle 50x50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for Sets of outdoor PT

33KV/√3 / 110V /√3 ,Single Phase, Outdoor type PT

Junction box with GI clamp for PT

Galvanized M.S. Channel 100x50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Galvanized M.S. Plate 400x400x8 mm.

Supply of material for busbars and connectors at busbar gantry

ACSR Panther conductor

ACSR Dog conductor

33 KV Post Insulator (If required)

33 KV Disc Insulator 70 KN, B & S Type

Disc fitting for Dog 70 KN

Wedge connector Panther to Panther

Wedge connector Panther to Dog

Connectors suitable for Panther

1. For LA suitable for panther

2. For Isolators suitable for panther

3. For CT/PT suitable for panther

4. For PI suitable for panther

5. For VCB suitable for panther

Supply of material for 33 KV R&C feeder panels

33 KV Relay & Control Panel for 33 KV Single Feeder 24 V DC ( with numeric relay, static TVM and communication port for SCADA)

Galvanized M.S. Channel 100x50x6 mm.

Supply of material for Control Cabling & Trench

LT Armoured Control Cable

10C x 2.5 Sq. mm.

4C x 4 Sq. mm.

2C x 4 Sq. mm.

Galvanized M.S. Angle 50x50x6 mm (for cable trench)

Galvanized M.S. Angle 40x40x5 mm. for cable trench covers

MS Bar, 10 mm

Perforated GI cable tray for control cable

(i) 400 x 75 x 2 mm (WxHxT)

(ii) 200 x 50 x 2 mm (WxHxT)

(iii) 100 x 50 x 2 mm width (WxHxT)

Supply of material for Special Earthing as per IS 3043-1987 with Soil treatment by highly conductive material (for earthing at Terminal Gantry and RMUs) (18 Nos)

GI pipe size 2500 mm x 80 mm dia x 4 mm thick

Galvanized earth electrode of size 2575 x 20 mm

Epoxy insulator for earthing strip, 150 mm length x 72 mm withstanding voltage of 28 KV rms

Highly conductive chemical around electrode - Earth Enhancing Compound

Highly conductive substances for treatment of soil - Earth Enhancing Compound and additional ground resistance improvement chemicals (if required for special or difficult locations).

GI strip 50 x 6 mm (1.7 kg /mtr.- 6 mtr. long for connecting RMU body / with earth electrode)

Sundry items (Chrome plated M.S. bolt & nut with washers Grease, Bitumen, Paint etc.)

Supply of cable fault locator and Test Van (01 No)

Cable Fault Location and Test Van including all equipment and portable instruments as per specification.

MANDATORY SPARE PARTS

Termination kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including screen and armour earth kits, all accessories and lugs).

33 KV Premoulded screen connector suitable for 36 KV RMU for rating 1Rx3Cx400 sq.mm. as per RMU OEM recommendation

Straight through jointing kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

33 KV bushing with O ring for indoor termination kit of RMU

SCHEDULE A2 : NEW 11 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES

POWER CABLES AND ACCESSORIES

6.35/11 KV (E) grade, Al conductor, TR-XLPE insulated, Cu tape screened, armoured, PVC sheathed power cable : 3-core/ 300 sqmm (Colour of Outer sheeth of Cable shall be different from 33 KV & LT cable as specified by UPCL)

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type including screen and armour earth kits, all accessories and lugs) as per RMU/CSS OEM recommendation

6.35/11 KV (E) grade, Al conductor, TR-XLPE insulated, Cu tape screened, armoured, PVC sheathed power cable : 3-core/ 50 Sqmm

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type includingscreen and armour earth kits, all accessories and lug) as per RMU/CSS OEM recommendation.

11 KV VCB FDR PANEL 350 MVA 400-200/5-5 A, 24 V DC SCADA compatible suitable to connect with FRTU (including adapter panel as reqd. for extension of existing bus panel )

Concrete route marker for HT cable having emboss "DANGER UPCL 11 KV CABLE BELOW" and directional arrows

B-Class Medium duty GI pipe as IS 1239, 150 mm. including coupling

11 KV 630A 21kA/3 sec Outdoor motorised extendible type SF6 insulated Ring Main Unit with 2 No. Load Break Switch as incomer & Outgoing and 1 nos. VCB Module as outgoings for DTR (CCV) with auxiliary power module and suitable to connect with FRTU including FPIs.

SUPPLY OF MATERIAL FOR CABLE JOINT PITS / INSPECTION CHAMBERS (212 Nos)

Straight through jointing kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated , screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

Galvanised M.S. Channel 125x65x6 mm. (for lid support mesh structure)

Duct sealing material / kit for duct dia 160 mm, sealing length upto 15 cm with expanding polyurethane filler or other sealant material suitable for PVC / HDPE sheathed cables .

SUPPLY OF MATERIAL FOR CABLE RISER AT EXISTING OH GANTRY AT SUBSTATION (26 Nos)

Galvanised M.S. Channel 100x50x6 mm.

Galvanised MS Angle 65x65x6 mm.

11 KV Polymer Pin Insulator with pin

GI clamps and cable cleat of suitable size for clamping GI pipe on cable riser

GI E Clamp with chrome plated nut & bolt with washer for 11 KV Pin insulator

9kV, 10kA Lightening Arrester, distribution type class with earth lead disconnector

GI Earthing Strip 50X6MM

Tinned Copper braid of size 50x6x1000 mm. with end lugs for earthing of HT cable

SUPPLY OF MATERIAL FOR IN / OUT CABLE RISER AT EXISTING DTR (166 Nos)

Galvanised M.S. Angle iron 50x50x6 mm (for cable support 2.24 mtr ln)

B-Class Medium duty GI pipe as IS 1239, 150 mm. including coupling

GI Clamps for S.T. Pole with Packing Piece

SUPPLY OF MATERIALS FOR NEW TERMINATION POLE STRUCTURE AT SUBSTATION (For new 11 kV Feeder Panels - 02 No)

Bottom Portion Hot Dip Galvanized S.T. Pole SP-23, 8.5 mtr. Long

Galvanized M.S. Channel 100x50x6 mm (for top channel & dropper channel & TPMO handle)

Galvanized M.S. Angle 75x75x8 mm (for TPMO & Fuse set 2.24 mtr. )

Galvanized M.S. Angle 50x50x6 mm (for cable support 2.24 mtr. )

11 KV TPMO Switch - 630 A complete

MS Earthing rod 20x2500mm

GI Wire 6 SWG

9kV, 10kA Lightening Arrester, distribution type class with earth lead disconnector

GI strip 35x6 mm. fo earthing of LA

11 KV Polymer pin insulator with pin

GI M.S. bolt & nut with washers off size

GI Clamps for S.T. Pole with Packing Piece

GI Clamp of required size with Packing Piece for holding cable supporting angle, cable & TPMO handle

Name plate of feeder with GI clamp

11 KV Danger board with GI clamp

Stone Pad 300x300x75

GI pipe 5" dia, 3mtr long

Supply of material for Special Earthing as per IS 3043-1987 with Soil treatment by highly conductive material (for earthing at Terminal Gantry, DTR terminations and RMUs ) (286 Nos)

GI pipe size 2500 mm x 80 mm dia x 4 mm thick

Galvanized earth electrode of size 2575 x 20 mm

Epoxy Insulator (for earthing strip) 150 mm length x 72 mm withstanding voltage of 28 KV rms

Highly conductive chemical around electrode - Earth Enhancing Compound

Highly conductive substances for treatment of soil - Earth Enhancing Compound and additional ground resistance improvement chemicals (if required for special or difficult locations).

GI strip 50 x 6 mm (1.7 kg /mtr.) 6 mtr. long for connecting transformer / RMU body / neutral with earth electrode

Sundry items (Chrome plated M.S. bolt & nut with washers Grease, Bitumen, Paint etc.)

Extensible Functional Units for 11 KV RMU

11 KV Extendible VCB functional unit for RMU with interconnecting bus bar

11 KV Extendible Load break switch (LBS) functional unit for RMU with interconnecting bus bar

MANDATORY SPARE PARTS

Straight through jointing kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated , screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type including screen and armour earth kits, all accessories and lugs) as per RMU/CSS OEM recommendation

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type includingscreen and armour earth kits, all accessories and lug) as per RMU/CSS OEM recommendation.

11 KV bushing with O ring for indoor termination kit of RMU

9 kg SF6 gas cylinder with SF6 gas refilling kit for RMU

SCHEDULE A3 : LT UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES

POWER CABLES AND ACCESSORIES

1.1 KV Grade XLPE Al. Conductor, PVC Sheathed, Armoured Cable 4C x 400 sq. mm. (for main LT cable) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor,PVC Sheathed, Armoured Cable 4C x 240 sq. mm. (for main LT cable) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor, PVC Sheathed, Armoured Cable 4C x 120 sq. mm. (for main LT cable) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor, FRLS, PVC Sheathed, Armoured Cable 4x95 sq.mm. (for load 26-75 KW) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor, FRLS, PVC Sheathed, Armoured Cable 4x16 sq.mm. (for load 5-25 KW)

1.1 KV Grade XLPE Al. Conductor, FRLS, PVC Sheathed, Armoured Cable 2x10 sq.mm. (for load upto 4 KW)

LT cable termination kit for LT XLPE armoured Cable 4Cx400 sq.mm.

LT cable termination kit for LT XLPE armoured Cable 4Cx240 sq.mm.

LT cabletermination kit for LT XLPE armoured Cable 4Cx120 sq.mm.

LT cable termination kit for LT XLPE armoured Cable 4x95 sq.mm.

Straight Through Joint Outdoor Type for LT XLPE Insulated, Armoured Cable 4Cx 400 sq. mm.

Straight Through Joint Outdoor Type for LT XLPE Insulated, Armoured Cable 4Cx 240 sq. mm.

Straight Through Joint Outdoor Type for LT XLPE Insulated, Armoured Cable 4Cx 120 sq. mm.

Long barrel Al Lugs - 400 sq. mm.

Long barrel Al Lugs - 240 sq. mm.

Long barrel Al Lugs - 120 sq. mm.

Long barrel Al Lugs - 95 sq. mm.

Long barrel Al Lugs - 16 sq. mm.

Long barrel Al Lugs - 10 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 400 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 240 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 120 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 95 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 16 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 10 sq. mm.

Tinned Copper braid of size 50x6x1000 mm. with end lugs

Concrete route marker for LT cable having emboss "DANGER UPCL LT CABLE BELOW" and directional arrows

Polycarbonate boxes for consumer energy meter 1-phase

Polycarbonate boxes for consumer energy meter 3-phase

LT PRMC (Pilferage Resistant Metering Cubical) with CTs for connecting with CT operated static energy meter,( CT accuracy class 1, ratios 50-150/5 A) for load connections 26-75 KW (excluding supply of energy meter)

B-Class GI pipe as IS 1239 - 150 mm with coupling

GI Holding clamp for B-Class Heavy duty GI pipe as IS 1239, 150 mm. on ST/ rail/PCC pole

LT metering cubical with 160 A 3-ph main bus bar & with 10 no. metering cubicals to install three phase meters with locking provision and associated mounting structure (excluding supply of energy meters)

SUPPLY OF MATERIAL FOR PROVIDING LIGHTENING ARRESTER ON DTR POLE (83 Nos)

9kV, 10kA Lightening Arrester distribution class with earth lead disconnector

GI Earthing strip 35x6 mm

SUPPLY OF MATERIAL FOR BUS ISOLATOR ON DTR POLE (83 Nos)

Galvanised MS Channel 100x50x6 mm.

11 KV Bus Isolator 400 A

GI Clamp with packing piece for SP-55 with Chrome plated M.S. bolt & nut with washers.

SUPPLY OF MATERIAL FOR PROVIDING 11 KV FUSE SET (HORN GAP) ON DTR POLE (83 Nos)

11 KV Polymer pin insulator with pin

Galvanised MS Channel 100x50x6 mm.

GI Clamp with packing piece for SP-55 with Chrome plated M.S. bolt & nut with washers.

SUPPLY OF MATERIAL FOR 1000 KVA CSS (20 Nos)

11/0.433 KV 1000 KVA Compact Secondary Substation complete with (a) dry type distribution transformer (b) 12 kV SCADA compatible motorized RMU with 2 Nos 630A LBS , 630 A VCB, 01 No FPI (c) LV switchgear consisting of 2000A, 4P microprocessor based ACB and 04 Nos 630 A microprocessor controlled MCCB (d) IP54 outdoor enclosure and all accesories / protections as per specification

SUPPLY OF MATERIAL FOR LT PROTECTION OF 400 KVA 11/0.4 KV DTR (08 Nos)

LT XLPE FRLS Cable 1Cx630 sq.mm.

LT ACB 800 A including microprocessor release IPR, Manual drawout type (3 pole with NCT as per IS 13947-2 & IEC 69047-2) with panel (IP 54 protection level) with provision of DTR metering with 600/5A CTs, DLMS compliant energy meter with GPRS communication module and mounting structure as per specification

SUPPLY OF MATERIAL FOR LT PROTECTION OF 250/160 KVA 11/0.4 KV DTR (52 Nos)

LT XLPE FRLS Cable 1Cx400 sq.mm

LT ACB 800 A including microprocessor release IPR, Manual drawout type (3 pole with NCT as per IS 13947-2 & IEC 69047-2) with panel (IP 54 protection level) with provision of DTR metering with 400/5A CTs, DLMS compliant energy meter with GPRS communication module and mounting structure as per specification

SUPPLY OF MATERIAL FOR LT PROTECTION OF 100/63/25 KVA 11/0.4 KV DTR (23 Nos)

LT XLPE FRLS Cable 1Cx240 sq.mm

LT MCCB 250 A with provision of DTR metering with 200/5A CTs, DLMS compliant energy meter with GPRS communication module and mounting structure as per specification with enclosure IP 54

SUPPLY OF MATERIAL FOR LT FEEDER PILLAR BOXES

Outdoor type fully enclosed weather proof (IP54) Feeder Pillar having 400 Amps MCCB as incomer and 2 no. 250 A MCCB as outgoing, as per specifications. Type-A with mounting structure of minimum hieght of 750mm above ground level as per UPCL approved drawing.

Outdoor type fully enclosed weather proof (IP54) Feeder Pillar having 400 A bus bar as incomer and 3 no.160 A MCCB as outgoing, as per specifications. Type-B with mounting structure of minimum hieght of 750mm above ground level as per UPCL approved drawing.

Outdoor 400 Amp. 3 Phase LT bus bar type fully enclosed weather proof (IP54) Feeder Pillar having 400 Amps Al. bus bar as per specifications. Type-C with mounting structure of minimum hieght of 750mm above ground level as per UPCL approved drawing.

SUPPLY OF MATERIAL FOR SPECIAL EARTHING AS PER IS 3043-1987 WITH SOIL TREATMENT BY HIGHLY CONDUCTIVE MATERIAL (349 Nos)

GI pipe size 2500 mm x80 mm dia x 4 mm thick

Galvanized earth electrode of size 2575 x 20 mm

Epoxy Insulator (for earthing strip) 150 mm length x 72 mm withstanding voltage of 28 KV rms

Highly conductive chemical around electrode - Earth Enhancing Compound

Highly conductive substances for treatment of soil - Earth Enhancing Compound and additional ground resistance improvement chemicals

GI strip 50 x 6 mm (1.7 kg /mtr.) 6 mtr. long for connecting transformer body / neutral with earth electrode

Sundry items (Chrome plated M.S. bolt & nut with washers, Grease, Bitumen, Paint etc.)

SUPPLY OF MATERIAL FOR EARTHING WITH EARTH ROD FOR DTR PROTECTION CUBICALS AND LT FEEDER PILLARS (2852 Nos)

Earthing rod 20x2500 mm.

GI wire 6 SWG

Description of Work / Item(s)

Amount

SCHEDULE A1 : 33 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES

POWER CABLES AND ACCESSORIES

19/33 KV (E) grade, Al conductor, Tr-XLPE insulated, Cu tape screened, armoured, PVC sheathed power cable : 3-core/ 400 Sqmm (Colour of Outer sheeth of Cable shall be different from 11 KV & LT cable as specified by UPCL)

Termination kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR / heat-shrinkable type including screen and armour earth kits, all accessories and lugs.

33 KV Premoulded screen connector suitable for 36 KV RMU for rating 1Rx3Cx400 sq.mm. as per RMU OEM recommendation

B-Class medium duty GI pipe 150 mm - as per IS 1239 including coupling

33 KV 630A 25 kA/1 sec Outdoor Motorized SF6 insulated Ring Main Unit with 3 nos. VCB Module as incoming/ outgoing (VVV) including auxiliary power transformer, SCADA compatible and with suitable provisions with to connect with FRTU.

Concrete route marker for HT cable having emboss " DANGER UPCL 33 KV CABLE BELOW" and directional arrows

SUPPLY OF MATERIAL FOR CABLE JOINT PITS / INSPECTION CHAMBERS (64 Nos)

Straight through jointing kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated , screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

Galvanised M.S. Channel 125x65x6 mm. (for frabrication of lid support mesh structure)

Duct sealing material / kit for duct dia 160 mm, sealing length upto 15 cm with expanding polyurethane filler or other sealant material suitable for PVC / HDPE sheathed cables .

SUPPLY OF MATERIAL FOR OVERHEAD GRANTRY AT SUBSTATION

Supply of material for Cable riser at OH structure/Gantry (10 Nos )

Galvanised M.S. Channel 100x50x6 mm.

Galvanised MS Angle 65x65x6 mm.

33 KV Polymer Pin Insulator with GI pin

GI clamps and cable cleat of suitable size for clamping HDPE pipe of OD 160 mm. for holding HT cable on 33 KV Gantry & Line isolator

GI E Clamp for 33 KV Pin insulator

33kV, 10kA Lightning Arrester, distribution class with earth lead disconnector

GI Earthing Strip 50X6MM (for earting HT cables and RMUs)

Tinned Copper braid of size 50x6x1000 mm. with end lugs (for earthing of HT cable and RMU)

Supply of material for New Terminal Gantry at SUB-STATION (02 Nos)

R.S. Joist 175x85 (Grade E250-A, IS:2062)

R.S. Joist 175x85 for top (Grade E250-A, IS:2062)

Galvanized M.S. Angle 50x50x6 mm.

Galvanized M.S. Channel 100x50x6 mm (for LA)

33 KV Disc Insulator 70 KN, B & S Type

Disc fitting for Dog 70 KN

33kV, 10kA Lightning Arrester, Station class with all accessories and mounting hardware

Chrome plated M.S. bolt & nut with washers.

Stone pad 300x300x75 mm.

MS plate 225x225x8 mm thick

SUPPLY OF MATERIAL FOR 33KV BAY CONSTRUCTION OR UPGRADATION (01 No)

Supply of material for Line isolator (for 01 Bay + 01 addl line isolators)

Line Isolator, 800A, 33KV, triple pole single throw manually operated

Galvanized M.S. Channel 125x65x6 mm

Galvanized M.S. Angle 75x75x8 mm

Galvanized MS Angle 50x50x6 mm.

Galvanized M.S. flat 50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for Bus Isolator

Bus Isolator, 800A, 33KV, Triple pole, single throw, manually operated

Galvanized M.S. Channel 125x65x6 mm

Galvanized M.S. Angle 75x75x8 mm

Galvanized M.S. Angle 50x50x6 mm.

Galvanized M.S. flat 50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for 33KV VCB

33 KV, 1250A, 3 Phase outdoor type VCB, 24 V DC including GI mounting stand

Supply of material for Sets of Outdoor CT

33 KV Single Phase, Multi Core CT, Outdoor type, CTR 600-300/1-1-1 A

Junction box for CT

Galvanized M.S. Channel 125x65x6 mm

Galvanized M.S. Angle 75x75x8mm

Galvanized M.S. Plate 400x400x8 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for Bus Bar Gantry Structure

R.S. Joist 175x85x6 mm. (Grade E250-A, IS:2062)

R.S. Joist 175x85x6 mm. for top (Grade E250-A, IS:2062)

Galvanized M.S. Angle 50x50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for Sets of outdoor PT

33KV/√3 / 110V /√3 ,Single Phase, Outdoor type PT

Junction box with GI clamp for PT

Galvanized M.S. Channel 100x50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Galvanized M.S. Plate 400x400x8 mm.

Supply of material for busbars and connectors at busbar gantry

ACSR Panther conductor

ACSR Dog conductor

33 KV Post Insulator (If required)

33 KV Disc Insulator 70 KN, B & S Type

Disc fitting for Dog 70 KN

Wedge connector Panther to Panther

Wedge connector Panther to Dog

Connectors suitable for Panther

1. For LA suitable for panther

2. For Isolators suitable for panther

3. For CT/PT suitable for panther

4. For PI suitable for panther

5. For VCB suitable for panther

Supply of material for 33 KV R&C feeder panels

33 KV Relay & Control Panel for 33 KV Single Feeder 24 V DC ( with numeric relay, static TVM and communication port for SCADA)

Galvanized M.S. Channel 100x50x6 mm.

Supply of material for Control Cabling & Trench

LT Armoured Control Cable

10C x 2.5 Sq. mm.

4C x 4 Sq. mm.

2C x 4 Sq. mm.

Galvanized M.S. Angle 50x50x6 mm (for cable trench)

Galvanized M.S. Angle 40x40x5 mm. for cable trench covers

MS Bar, 10 mm

Perforated GI cable tray for control cable

(i) 400 x 75 x 2 mm (WxHxT)

(ii) 200 x 50 x 2 mm (WxHxT)

(iii) 100 x 50 x 2 mm width (WxHxT)

Supply of material for Special Earthing as per IS 3043-1987 with Soil treatment by highly conductive material (for earthing at Terminal Gantry and RMUs) (18 Nos)

GI pipe size 2500 mm x 80 mm dia x 4 mm thick

Galvanized earth electrode of size 2575 x 20 mm

Epoxy insulator for earthing strip, 150 mm length x 72 mm withstanding voltage of 28 KV rms

Highly conductive chemical around electrode - Earth Enhancing Compound

Highly conductive substances for treatment of soil - Earth Enhancing Compound and additional ground resistance improvement chemicals (if required for special or difficult locations).

GI strip 50 x 6 mm (1.7 kg /mtr.- 6 mtr. long for connecting RMU body / with earth electrode)

Sundry items (Chrome plated M.S. bolt & nut with washers Grease, Bitumen, Paint etc.)

Supply of cable fault locator and Test Van (01 No)

Cable Fault Location and Test Van including all equipment and portable instruments as per specification.

MANDATORY SPARE PARTS

Termination kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including screen and armour earth kits, all accessories and lugs).

33 KV Premoulded screen connector suitable for 36 KV RMU for rating 1Rx3Cx400 sq.mm. as per RMU OEM recommendation

Straight through jointing kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

33 KV bushing with O ring for indoor termination kit of RMU

SCHEDULE A2 : NEW 11 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES

POWER CABLES AND ACCESSORIES

6.35/11 KV (E) grade, Al conductor, TR-XLPE insulated, Cu tape screened, armoured, PVC sheathed power cable : 3-core/ 300 sqmm (Colour of Outer sheeth of Cable shall be different from 33 KV & LT cable as specified by UPCL)

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type including screen and armour earth kits, all accessories and lugs) as per RMU/CSS OEM recommendation

6.35/11 KV (E) grade, Al conductor, TR-XLPE insulated, Cu tape screened, armoured, PVC sheathed power cable : 3-core/ 50 Sqmm

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type includingscreen and armour earth kits, all accessories and lug) as per RMU/CSS OEM recommendation.

11 KV VCB FDR PANEL 350 MVA 400-200/5-5 A, 24 V DC SCADA compatible suitable to connect with FRTU (including adapter panel as reqd. for extension of existing bus panel )

Concrete route marker for HT cable having emboss "DANGER UPCL 11 KV CABLE BELOW" and directional arrows

B-Class Medium duty GI pipe as IS 1239, 150 mm. including coupling

11 KV 630A 21kA/3 sec Outdoor motorised extendible type SF6 insulated Ring Main Unit with 2 No. Load Break Switch as incomer & Outgoing and 1 nos. VCB Module as outgoings for DTR (CCV) with auxiliary power module and suitable to connect with FRTU including FPIs.

SUPPLY OF MATERIAL FOR CABLE JOINT PITS / INSPECTION CHAMBERS (212 Nos)

Straight through jointing kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated , screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

Galvanised M.S. Channel 125x65x6 mm. (for lid support mesh structure)

Duct sealing material / kit for duct dia 160 mm, sealing length upto 15 cm with expanding polyurethane filler or other sealant material suitable for PVC / HDPE sheathed cables .

SUPPLY OF MATERIAL FOR CABLE RISER AT EXISTING OH GANTRY AT SUBSTATION (26 Nos)

Galvanised M.S. Channel 100x50x6 mm.

Galvanised MS Angle 65x65x6 mm.

11 KV Polymer Pin Insulator with pin

GI clamps and cable cleat of suitable size for clamping GI pipe on cable riser

GI E Clamp with chrome plated nut & bolt with washer for 11 KV Pin insulator

9kV, 10kA Lightening Arrester, distribution type class with earth lead disconnector

GI Earthing Strip 50X6MM

Tinned Copper braid of size 50x6x1000 mm. with end lugs for earthing of HT cable

SUPPLY OF MATERIAL FOR IN / OUT CABLE RISER AT EXISTING DTR (166 Nos)

Galvanised M.S. Angle iron 50x50x6 mm (for cable support 2.24 mtr ln)

B-Class Medium duty GI pipe as IS 1239, 150 mm. including coupling

GI Clamps for S.T. Pole with Packing Piece

SUPPLY OF MATERIALS FOR NEW TERMINATION POLE STRUCTURE AT SUBSTATION (For new 11 kV Feeder Panels - 02 No)

Bottom Portion Hot Dip Galvanized S.T. Pole SP-23, 8.5 mtr. Long

Galvanized M.S. Channel 100x50x6 mm (for top channel & dropper channel & TPMO handle)

Galvanized M.S. Angle 75x75x8 mm (for TPMO & Fuse set 2.24 mtr. )

Galvanized M.S. Angle 50x50x6 mm (for cable support 2.24 mtr. )

11 KV TPMO Switch - 630 A complete

MS Earthing rod 20x2500mm

GI Wire 6 SWG

11kV, 10kA Lightening Arrester, distribution type class with earth lead disconnector

GI strip 35x6 mm. fo earthing of LA

11 KV Polymer pin insulator with pin

GI M.S. bolt & nut with washers off size

GI Clamps for S.T. Pole with Packing Piece

GI Clamp of required size with Packing Piece for holding cable supporting angle, cable & TPMO handle

Name plate of feeder with GI clamp

11 KV Danger board with GI clamp

Stone Pad 300x300x75

GI pipe 5" dia, 3mtr long

Supply of material for Special Earthing as per IS 3043-1987 with Soil treatment by highly conductive material (for earthing at Terminal Gantry, DTR terminations and RMUs ) (286 Nos)

GI pipe size 2500 mm x 80 mm dia x 4 mm thick

Galvanized earth electrode of size 2575 x 20 mm

Epoxy Insulator (for earthing strip) 150 mm length x 72 mm withstanding voltage of 28 KV rms

Highly conductive chemical around electrode - Earth Enhancing Compound

Highly conductive substances for treatment of soil - Earth Enhancing Compound and additional ground resistance improvement chemicals (if required for special or difficult locations).

GI strip 50 x 6 mm (1.7 kg /mtr.) 6 mtr. long for connecting transformer / RMU body / neutral with earth electrode

Sundry items (Chrome plated M.S. bolt & nut with washers Grease, Bitumen, Paint etc.)

Extensible Functional Units for 11 KV RMU

11 KV Extendible VCB functional unit for RMU with interconnecting bus bar

11 KV Extendible Load break switch (LBS) functional unit for RMU with interconnecting bus bar

MANDATORY SPARE PARTS

Straight through jointing kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated , screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type including screen and armour earth kits, all accessories and lugs) as per RMU/CSS OEM recommendation

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type includingscreen and armour earth kits, all accessories and lug) as per RMU/CSS OEM recommendation.

11 KV bushing with O ring for indoor termination kit of RMU

9 kg SF6 gas cylinder with SF6 gas refilling kit for RMU

SCHEDULE A3 : LT UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES

POWER CABLES AND ACCESSORIES

1.1 KV Grade XLPE Al. Conductor, PVC Sheathed, Armoured Cable 4C x 400 sq. mm. (for main LT cable) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor,PVC Sheathed, Armoured Cable 4C x 240 sq. mm. (for main LT cable) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor, PVC Sheathed, Armoured Cable 4C x 120 sq. mm. (for main LT cable) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor, FRLS, PVC Sheathed, Armoured Cable 4x95 sq.mm. (for load 26-75 KW) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor, FRLS, PVC Sheathed, Armoured Cable 4x16 sq.mm. (for load 5-25 KW)

1.1 KV Grade XLPE Al. Conductor, FRLS, PVC Sheathed, Armoured Cable 2x10 sq.mm. (for load upto 4 KW)

LT cable termination kit for LT XLPE armoured Cable 4Cx400 sq.mm.

LT cable termination kit for LT XLPE armoured Cable 4Cx240 sq.mm.

LT cabletermination kit for LT XLPE armoured Cable 4Cx120 sq.mm.

LT cable termination kit for LT XLPE armoured Cable 4x95 sq.mm.

Straight Through Joint Outdoor Type for LT XLPE Insulated, Armoured Cable 4Cx 400 sq. mm.

Straight Through Joint Outdoor Type for LT XLPE Insulated, Armoured Cable 4Cx 240 sq. mm.

Straight Through Joint Outdoor Type for LT XLPE Insulated, Armoured Cable 4Cx 120 sq. mm.

Long barrel Al Lugs - 400 sq. mm.

Long barrel Al Lugs - 240 sq. mm.

Long barrel Al Lugs - 120 sq. mm.

Long barrel Al Lugs - 95 sq. mm.

Long barrel Al Lugs - 16 sq. mm.

Long barrel Al Lugs - 10 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 400 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 240 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 120 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 95 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 16 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 10 sq. mm.

Tinned Copper braid of size 50x6x1000 mm. with end lugs

Concrete route marker for LT cable having emboss "DANGER UPCL LT CABLE BELOW" and directional arrows

Polycarbonate boxes for consumer energy meter 1-phase

Polycarbonate boxes for consumer energy meter 3-phase

LT PRMC (Pilferage Resistant Metering Cubical) with CTs for connecting with CT operated static energy meter,( CT accuracy class 1, ratios 50-150/5 A) for load connections 26-75 KW (excluding supply of energy meter)

B-Class GI pipe as IS 1239 - 150 mm with coupling

GI Holding clamp for B-Class Heavy duty GI pipe as IS 1239, 150 mm. on ST/ rail/PCC pole

LT metering cubical with 160 A 3-ph main bus bar & with 10 no. metering cubicals to install three phase meters with locking provision and associated mounting structure (excluding supply of energy meters)

SUPPLY OF MATERIAL FOR PROVIDING LIGHTENING ARRESTOR ON DTR POLE (83 Nos)

9kV, 10kA Lightening Arrester distribution class with earth lead disconnector

GI Earthing strip 35x6 mm

SUPPLY OF MATERIAL FOR BUS ISOLATOR ON DTR POLE (83 Nos)

Galvanised MS Channel 100x50x6 mm.

11 KV Bus Isolator 400 A

GI Clamp with packing piece for SP-55 with Chrome plated M.S. bolt & nut with washers.

SUPPLY OF MATERIAL FOR PROVIDING 11 KV FUSE SET (HORN GAP) ON DTR POLE (83 Nos)

11 KV Polymer pin insulator with pin

Galvanised MS Channel 100x50x6 mm.

GI Clamp with packing piece for SP-55 with Chrome plated M.S. bolt & nut with washers.

SUPPLY OF MATERIAL FOR 1000 KVA CSS (20 Nos)

11/0.433 KV 1000 KVA Compact Secondary Substation complete with (a) dry type distribution transformer (b) 12 kV SCADA compatible motorized RMU with 2 Nos 630A LBS , 630 A VCB, 01 No FPI (c) LV switchgear consisting of 2000A, 4P microprocessor based ACB and 04 Nos 630 A microprocessor controlled MCCB (d) IP54 outdoor enclosure and all accesories / protections as per specification

SUPPLY OF MATERIAL FOR LT PROTECTION OF 400 KVA 11/0.4 KV DTR (08 Nos)

LT XLPE FRLS Cable 1Cx630 sq.mm.

LT ACB 800 A including microprocessor release IPR, Manual drawout type (3 pole with NCT as per IS 13947-2 & IEC 69047-2) with panel (IP 54 protection level) with provision of DTR metering with 600/5A CTs, DLMS compliant energy meter with GPRS communication module and mounting structure as per specification

SUPPLY OF MATERIAL FOR LT PROTECTION OF 250/160 KVA 11/0.4 KV DTR (52 Nos)

LT XLPE FRLS Cable 1Cx400 sq.mm

LT ACB 800 A including microprocessor release IPR, Manual drawout type (3 pole with NCT as per IS 13947-2 & IEC 69047-2) with panel (IP 54 protection level) with provision of DTR metering with 400/5A CTs, DLMS compliant energy meter with GPRS communication module and mounting structure as per specification

SUPPLY OF MATERIAL FOR LT PROTECTION OF 100/63/25 KVA 11/0.4 KV DTR (23 Nos)

LT XLPE FRLS Cable 1Cx240 sq.mm

LT MCCB 250 A with provision of DTR metering with 200/5A CTs, DLMS compliant energy meter with GPRS communication module and mounting structure as per specification with enclosure IP 54

SUPPLY OF MATERIAL FOR LT FEEDER PILLAR BOXES

Outdoor type fully enclosed weather proof (IP54) Feeder Pillar having 400 Amps MCCB as incomer and 2 no. 250 A MCCB as outgoing, as per specifications. Type-A with mounting structure of minimum hieght of 750mm above ground level as per UPCL approved drawing.

Outdoor type fully enclosed weather proof (IP54) Feeder Pillar having 400 A bus bar as incomer and 3 no.160 A MCCB as outgoing, as per specifications. Type-B with mounting structure of minimum hieght of 750mm above ground level as per UPCL approved drawing.

Outdoor 400 Amp. 3 Phase LT bus bar type fully enclosed weather proof (IP54) Feeder Pillar having 400 Amps Al. bus bar as per specifications. Type-C with mounting structure of minimum hieght of 750mm above ground level as per UPCL approved drawing.

SUPPLY OF MATERIAL FOR SPECIAL EARTHING AS PER IS 3043-1987 WITH SOIL TREATMENT BY HIGHLY CONDUCTIVE MATERIAL (349 Nos)

GI pipe size 2500 mm x80 mm dia x 4 mm thick

Galvanized earth electrode of size 2575 x 20 mm

Epoxy Insulator (for earthing strip) 150 mm length x 72 mm withstanding voltage of 28 KV rms

Highly conductive chemical around electrode - Earth Enhancing Compound

Highly conductive substances for treatment of soil - Earth Enhancing Compound and additional ground resistance improvement chemicals

GI strip 50 x 6 mm (1.7 kg /mtr.) 6 mtr. long for connecting transformer body / neutral with earth electrode

Sundry items (Chrome plated M.S. bolt & nut with washers, Grease, Bitumen, Paint etc.)

SUPPLY OF MATERIAL FOR EARTHING WITH EARTH ROD FOR DTR PROTECTION CUBICALS AND LT FEEDER PILLARS (2852 Nos)

Earthing rod 20x2500 mm.

GI wire 6 SWG

Description of Work / Item(s)

Amount

Design Services for 33 kV,11kV & LT Underground Cable Lines (Schedules A1, A2 and A3)

Survey and design works for all 33 kV, 11 kV and LV underground lines as per scope of works, technical specifications and bid documents (section 6) including the following; (a) Preperation of preliminary cable route plan and maps as per scope of works. (b) Ground Penetrating Radar (GPR) survey of existing underground networks / installations of all utilities along the proposed line routes such as water, gas, sewage, communication etc. GPR Survey report and associated drawings shall be submitted in soft and hard copy before execution of work. (c) Detailed route survey , line design and preparation of georeferenced survey maps / drawings with final route plan for installation of underground cables and other facilities such as RMUs, DTRs, Compact substations, feeder pillars (LT), consumer indexing and locations for cable joints. (d) Preparation of updated schedules of quantities / BOQs for each subproject, construction drawings and maps. (e) preparation of final as-built drawings /georeferenced maps with all necessary details as required for O&M works upon completion of construction works. (f) Survey maps and associated drawings shall be submitted in soft and hard copy both before and after execution of work.

Description of Work / Item(s)

Amount

SCHEDULE A1 : 33 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES

POWER CABLES AND ACCESSORIES

19/33 KV (E) grade, Al conductor, Tr-XLPE insulated, Cu tape screened, armoured, PVC sheathed power cable : 3-core/ 400 Sqmm (Colour of Outer sheeth of Cable shall be different from 11 KV & LT cable as specified by UPCL)

Termination kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR / heat-shrinkable type including screen and armour earth kits, all accessories and lugs.

33 KV Premoulded screen connector suitable for 36 KV RMU for rating 1Rx3Cx400 sq.mm. as per RMU OEM recommendation

B-Class medium duty GI pipe 150 mm - as per IS 1239 including coupling

33 KV 630A 25 kA/1 sec Outdoor Motorized SF6 insulated Ring Main Unit with 3 nos. VCB Module as incoming/ outgoing (VVV) including auxiliary power transformer, SCADA compatible and with suitable provisions with to connect with FRTU.

Concrete route marker for HT cable having emboss " DANGER UPCL 33 KV CABLE BELOW" and directional arrows

SUPPLY OF MATERIAL FOR CABLE JOINT PITS / INSPECTION CHAMBERS (64 Nos)

Straight through jointing kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated , screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

Galvanised M.S. Channel 125x65x6 mm. (for frabrication of lid support mesh structure)

Duct sealing material / kit for duct dia 160 mm, sealing length upto 15 cm with expanding polyurethane filler or other sealant material suitable for PVC / HDPE sheathed cables .

SUPPLY OF MATERIAL FOR OVERHEAD GRANTRY AT SUBSTATION

Supply of material for Cable riser at OH structure/Gantry (10 Nos )

Galvanised M.S. Channel 100x50x6 mm.

Galvanised MS Angle 65x65x6 mm.

33 KV Polymer Pin Insulator with GI pin

GI clamps and cable cleat of suitable size for clamping HDPE pipe of OD 160 mm. for holding HT cable on 33 KV Gantry & Line isolator

GI E Clamp for 33 KV Pin insulator

33kV, 10kA Lightning Arrester, distribution class with earth lead disconnector

GI Earthing Strip 50X6MM (for earting HT cables and RMUs)

Tinned Copper braid of size 50x6x1000 mm. with end lugs (for earthing of HT cable and RMU)

Supply of material for New Terminal Gantry at SUB-STATION (02 Nos)

R.S. Joist 175x85 (Grade E250-A, IS:2062)

R.S. Joist 175x85 for top (Grade E250-A, IS:2062)

Galvanized M.S. Angle 50x50x6 mm.

Galvanized M.S. Channel 100x50x6 mm (for LA)

33 KV Disc Insulator 70 KN, B & S Type

Disc fitting for Dog 70 KN

33kV, 10kA Lightning Arrester, Station class with all accessories and mounting hardware

Chrome plated M.S. bolt & nut with washers.

Stone pad 300x300x75 mm.

MS plate 225x225x8 mm thick

SUPPLY OF MATERIAL FOR 33KV BAY CONSTRUCTION OR UPGRADATION (01 No)

Supply of material for Line isolator (for 01 Bay + 01 addl line isolators)

Line Isolator, 800A, 33KV, triple pole single throw manually operated

Galvanized M.S. Channel 125x65x6 mm

Galvanized M.S. Angle 75x75x8 mm

Galvanized MS Angle 50x50x6 mm.

Galvanized M.S. flat 50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for Bus Isolator

Bus Isolator, 800A, 33KV, Triple pole, single throw, manually operated

Galvanized M.S. Channel 125x65x6 mm

Galvanized M.S. Angle 75x75x8 mm

Galvanized M.S. Angle 50x50x6 mm.

Galvanized M.S. flat 50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for 33KV VCB

33 KV, 1250A, 3 Phase outdoor type VCB, 24 V DC including GI mounting stand

Supply of material for Sets of Outdoor CT

33 KV Single Phase, Multi Core CT, Outdoor type, CTR 600-300/1-1-1 A

Junction box for CT

Galvanized M.S. Channel 125x65x6 mm

Galvanized M.S. Angle 75x75x8mm

Galvanized M.S. Plate 400x400x8 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for Bus Bar Gantry Structure

R.S. Joist 175x85x6 mm. (Grade E250-A, IS:2062)

R.S. Joist 175x85x6 mm. for top (Grade E250-A, IS:2062)

Galvanized M.S. Angle 50x50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Supply of material for Sets of outdoor PT

33KV/√3 / 110V /√3 ,Single Phase, Outdoor type PT

Junction box with GI clamp for PT

Galvanized M.S. Channel 100x50x6 mm.

Chrome plated M.S. bolt & nut with washers.

Galvanized M.S. Plate 400x400x8 mm.

Supply of material for busbars and connectors at busbar gantry

ACSR Panther conductor

ACSR Dog conductor

33 KV Post Insulator (If required)

33 KV Disc Insulator 70 KN, B & S Type

Disc fitting for Dog 70 KN

Wedge connector Panther to Panther

Wedge connector Panther to Dog

Connectors suitable for Panther

1. For LA suitable for panther

2. For Isolators suitable for panther

3. For CT/PT suitable for panther

4. For PI suitable for panther

5. For VCB suitable for panther

Supply of material for 33 KV R&C feeder panels

33 KV Relay & Control Panel for 33 KV Single Feeder 24 V DC ( with numeric relay, static TVM and communication port for SCADA)

Galvanized M.S. Channel 100x50x6 mm.

Supply of material for Control Cabling & Trench

LT Armoured Control Cable

10C x 2.5 Sq. mm.

4C x 4 Sq. mm.

2C x 4 Sq. mm.

Galvanized M.S. Angle 50x50x6 mm (for cable trench)

Galvanized M.S. Angle 40x40x5 mm. for cable trench covers

MS Bar, 10 mm

Perforated GI cable tray for control cable

(i) 400 x 75 x 2 mm (WxHxT)

(ii) 200 x 50 x 2 mm (WxHxT)

(iii) 100 x 50 x 2 mm width (WxHxT)

Supply of material for Special Earthing as per IS 3043-1987 with Soil treatment by highly conductive material (for earthing at Terminal Gantry and RMUs) (18 Nos)

GI pipe size 2500 mm x 80 mm dia x 4 mm thick

Galvanized earth electrode of size 2575 x 20 mm

Epoxy insulator for earthing strip, 150 mm length x 72 mm withstanding voltage of 28 KV rms

Highly conductive chemical around electrode - Earth Enhancing Compound

Highly conductive substances for treatment of soil - Earth Enhancing Compound and additional ground resistance improvement chemicals (if required for special or difficult locations).

GI strip 50 x 6 mm (1.7 kg /mtr.- 6 mtr. long for connecting RMU body / with earth electrode)

Sundry items (Chrome plated M.S. bolt & nut with washers Grease, Bitumen, Paint etc.)

Supply of cable fault locator and Test Van (01 No)

Cable Fault Location and Test Van including all equipment and portable instruments as per specification.

MANDATORY SPARE PARTS

Termination kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including screen and armour earth kits, all accessories and lugs).

33 KV Premoulded screen connector suitable for 36 KV RMU for rating 1Rx3Cx400 sq.mm. as per RMU OEM recommendation

Straight through jointing kit for 33 KV Grade, 3-core, 400 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

33 KV bushing with O ring for indoor termination kit of RMU

SCHEDULE A2 : NEW 11 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES

POWER CABLES AND ACCESSORIES

6.35/11 KV (E) grade, Al conductor, TR-XLPE insulated, Cu tape screened, armoured, PVC sheathed power cable : 3-core/ 300 sqmm (Colour of Outer sheeth of Cable shall be different from 33 KV & LT cable as specified by UPCL)

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type including screen and armour earth kits, all accessories and lugs) as per RMU/CSS OEM recommendation

6.35/11 KV (E) grade, Al conductor, TR-XLPE insulated, Cu tape screened, armoured, PVC sheathed power cable : 3-core/ 50 Sqmm

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type includingscreen and armour earth kits, all accessories and lug) as per RMU/CSS OEM recommendation.

11 KV VCB FDR PANEL 350 MVA 400-200/5-5 A, 24 V DC SCADA compatible suitable to connect with FRTU (including adapter panel as reqd. for extension of existing bus panel )

Concrete route marker for HT cable having emboss "DANGER UPCL 11 KV CABLE BELOW" and directional arrows

B-Class Medium duty GI pipe as IS 1239, 150 mm. including coupling

11 KV 630A 21kA/3 sec Outdoor motorised extendible type SF6 insulated Ring Main Unit with 2 No. Load Break Switch as incomer & Outgoing and 1 nos. VCB Module as outgoings for DTR (CCV) with auxiliary power module and suitable to connect with FRTU including FPIs.

SUPPLY OF MATERIAL FOR CABLE JOINT PITS / INSPECTION CHAMBERS (212 Nos)

Straight through jointing kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated , screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

Galvanised M.S. Channel 125x65x6 mm. (for lid support mesh structure)

Duct sealing material / kit for duct dia 160 mm, sealing length upto 15 cm with expanding polyurethane filler or other sealant material suitable for PVC / HDPE sheathed cables .

SUPPLY OF MATERIAL FOR CABLE RISER AT EXISTING OH GANTRY AT SUBSTATION (26 Nos)

Galvanised M.S. Channel 100x50x6 mm.

Galvanised MS Angle 65x65x6 mm.

11 KV Polymer Pin Insulator with pin

GI clamps and cable cleat of suitable size for clamping GI pipe on cable riser

GI E Clamp with chrome plated nut & bolt with washer for 11 KV Pin insulator

9kV, 10kA Lightening Arrester, distribution type class with earth lead disconnector

GI Earthing Strip 50X6MM

Tinned Copper braid of size 50x6x1000 mm. with end lugs for earthing of HT cable

SUPPLY OF MATERIAL FOR IN / OUT CABLE RISER AT EXISTING DTR (166 Nos)

Galvanised M.S. Angle iron 50x50x6 mm (for cable support 2.24 mtr ln)

B-Class Medium duty GI pipe as IS 1239, 150 mm. including coupling

GI Clamps for S.T. Pole with Packing Piece

SUPPLY OF MATERIALS FOR NEW TERMINATION POLE STRUCTURE AT SUBSTATION (For new 11 kV Feeder Panels - 02 No)

Bottom Portion Hot Dip Galvanized S.T. Pole SP-23, 8.5 mtr. Long

Galvanized M.S. Channel 100x50x6 mm (for top channel & dropper channel & TPMO handle)

Galvanized M.S. Angle 75x75x8 mm (for TPMO & Fuse set 2.24 mtr. )

Galvanized M.S. Angle 50x50x6 mm (for cable support 2.24 mtr. )

11 KV TPMO Switch - 630 A complete

MS Earthing rod 20x2500mm

GI Wire 6 SWG

9kV, 10kA Lightening Arrester, distribution type class with earth lead disconnector

GI strip 35x6 mm. fo earthing of LA

11 KV Polymer pin insulator with pin

GI M.S. bolt & nut with washers off size

GI Clamps for S.T. Pole with Packing Piece

GI Clamp of required size with Packing Piece for holding cable supporting angle, cable & TPMO handle

Name plate of feeder with GI clamp

11 KV Danger board with GI clamp

Stone Pad 300x300x75

GI pipe 5" dia, 3mtr long

Supply of material for Special Earthing as per IS 3043-1987 with Soil treatment by highly conductive material (for earthing at Terminal Gantry, DTR terminations and RMUs ) (286 Nos)

GI pipe size 2500 mm x 80 mm dia x 4 mm thick

Galvanized earth electrode of size 2575 x 20 mm

Epoxy Insulator (for earthing strip) 150 mm length x 72 mm withstanding voltage of 28 KV rms

Highly conductive chemical around electrode - Earth Enhancing Compound

Highly conductive substances for treatment of soil - Earth Enhancing Compound and additional ground resistance improvement chemicals (if required for special or difficult locations).

GI strip 50 x 6 mm (1.7 kg /mtr.) 6 mtr. long for connecting transformer / RMU body / neutral with earth electrode

Sundry items (Chrome plated M.S. bolt & nut with washers Grease, Bitumen, Paint etc.)

Extensible Functional Units for 11 KV RMU

11 KV Extendible manual VCB functional unit for RMU with interconnecting bus bar

11 KV Extendible manual Load break switch (LBS) functional unit for RMU with interconnecting bus bar

MANDATORY SPARE PARTS

Straight through jointing kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated , screened, armoured, PVC sheathed power cable, heat-shrink type including termite proofing SS mesh and all accessories

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 300 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type including screen and armour earth kits, all accessories and lugs) as per RMU/CSS OEM recommendation

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, OUTDOOR (Heat-shrinkable type including including screen and armour earth kits, all accessories and lugs).

Termination kit for 11 KV Grade, 3-core, 50 Sq.mm, Al conductor, XLPE insulated, screened, armoured, PVC sheathed power cable, INDOOR (Heat-shrinkable type includingscreen and armour earth kits, all accessories and lug) as per RMU/CSS OEM recommendation.

11 KV bushing with O ring for indoor termination kit of RMU

9 kg SF6 gas cylinder with SF6 gas refilling kit for RMU

SCHEDULE A3 : LT UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES

POWER CABLES AND ACCESSORIES

1.1 KV Grade XLPE Al. Conductor, PVC Sheathed, Armoured Cable 4C x 400 sq. mm. (for main LT cable) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor,PVC Sheathed, Armoured Cable 4C x 240 sq. mm. (for main LT cable) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor, PVC Sheathed, Armoured Cable 4C x 120 sq. mm. (for main LT cable) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor, FRLS, PVC Sheathed, Armoured Cable 4x95 sq.mm. (for load 26-75 KW) (Colour of Outer sheeth of Cable shall be different from 33 KV & 11 KV cable as specified by UPCL)

1.1 KV Grade XLPE Al. Conductor, FRLS, PVC Sheathed, Armoured Cable 4x16 sq.mm. (for load 5-25 KW)

1.1 KV Grade XLPE Al. Conductor, FRLS, PVC Sheathed, Armoured Cable 2x10 sq.mm. (for load upto 4 KW)

LT cable termination kit for LT XLPE armoured Cable 4Cx400 sq.mm.

LT cable termination kit for LT XLPE armoured Cable 4Cx240 sq.mm.

LT cabletermination kit for LT XLPE armoured Cable 4Cx120 sq.mm.

LT cable termination kit for LT XLPE armoured Cable 4x95 sq.mm.

Straight Through Joint Outdoor Type for LT XLPE Insulated, Armoured Cable 4Cx 400 sq. mm.

Straight Through Joint Outdoor Type for LT XLPE Insulated, Armoured Cable 4Cx 240 sq. mm.

Straight Through Joint Outdoor Type for LT XLPE Insulated, Armoured Cable 4Cx 120 sq. mm.

Long barrel Al Lugs - 400 sq. mm.

Long barrel Al Lugs - 240 sq. mm.

Long barrel Al Lugs - 120 sq. mm.

Long barrel Al Lugs - 95 sq. mm.

Long barrel Al Lugs - 16 sq. mm.

Long barrel Al Lugs - 10 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 400 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 240 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 120 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 95 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 16 sq. mm.

Double compression Glands for LT XLPE Insulated, Armoured Cable, 10 sq. mm.

Tinned Copper braid of size 50x6x1000 mm. with end lugs

Concrete route marker for LT cable having emboss "DANGER UPCL LT CABLE BELOW" and directional arrows

Polycarbonate boxes for consumer energy meter 1-phase

Polycarbonate boxes for consumer energy meter 3-phase

LT PRMC (Pilferage Resistant Metering Cubical) with CTs for connecting with CT operated static energy meter,( CT accuracy class 1, ratios 50-150/5 A) for load connections 26-75 KW (excluding supply of energy meter)

B-Class medium duty GI pipe 150 mm - as per IS 1239 including coupling

GI Holding clamp for B-Class Heavy duty GI pipe as IS 1239, 150 mm. on ST/ rail/PCC pole

LT metering cubical with 160 A 3-ph main bus bar & with 10 no. metering cubicals to install three phase meters with locking provision and associated mounting structure (excluding supply of energy meters)

SUPPLY OF MATERIAL FOR PROVIDING LIGHTENING ARRESTOR ON DTR POLE (83 Nos)

9kV, 10kA Lightening Arrester distribution class with earth lead disconnector

GI Earthing strip 35x6 mm

SUPPLY OF MATERIAL FOR BUS ISOLATOR ON DTR POLE (83 Nos)

Galvanised MS Channel 100x50x6 mm.

11 KV Bus Isolator 400 A

GI Clamp with packing piece for SP-55 with Chrome plated M.S. bolt & nut with washers.

SUPPLY OF MATERIAL FOR PROVIDING 11 KV FUSE SET (HORN GAP) ON DTR POLE (83 Nos)

11 KV Polymer pin insulator with pin

Galvanised MS Channel 100x50x6 mm.

GI Clamp with packing piece for SP-55 with Chrome plated M.S. bolt & nut with washers.

SUPPLY OF MATERIAL FOR 1000 KVA CSS (20 Nos)

11/0.433 KV 1000 KVA Compact Secondary Substation complete with (a) dry type distribution transformer (b) 12 kV SCADA compatible motorized RMU with 2 Nos 630A LBS , 630 A VCB, 01 No FPI (c) LV switchgear consisting of 2000A, 4P microprocessor based ACB and 04 Nos 630 A microprocessor controlled MCCB (d) IP54 outdoor enclosure and all accesories / protections as per specification

SUPPLY OF MATERIAL FOR LT PROTECTION OF 400 KVA 11/0.4 KV DTR (08 Nos)

LT XLPE FRLS Cable 1Cx630 sq.mm.

LT ACB 800 A including microprocessor release IPR, Manual drawout type (3 pole with NCT as per IS 13947-2 & IEC 69047-2) with panel (IP 54 protection level) with provision of DTR metering with 600/5A CTs, DLMS compliant energy meter with GPRS communication module and mounting structure as per specification

SUPPLY OF MATERIAL FOR LT PROTECTION OF 250/160 KVA 11/0.4 KV DTR (52 Nos)

LT XLPE FRLS Cable 1Cx400 sq.mm

LT ACB 800 A including microprocessor release IPR, Manual drawout type (3 pole with NCT as per IS 13947-2 & IEC 69047-2) with panel (IP 54 protection level) with provision of DTR metering with 400/5A CTs, DLMS compliant energy meter with GPRS communication module and mounting structure as per specification

SUPPLY OF MATERIAL FOR LT PROTECTION OF 100/63/25 KVA 11/0.4 KV DTR (23 Nos)

LT XLPE FRLS Cable 1Cx240 sq.mm

LT MCCB 250 A with provision of DTR metering with 200/5A CTs, DLMS compliant energy meter with GPRS communication module and mounting structure as per specification with enclosure IP 54

SUPPLY OF MATERIAL FOR LT FEEDER PILLAR BOXES

Outdoor type fully enclosed weather proof (IP54) Feeder Pillar having 400 Amps MCCB as incomer and 2 no. 250 A MCCB as outgoing, as per specifications. Type-A with mounting structure of minimum hieght of 750mm above ground level as per UPCL approved drawing.

Outdoor type fully enclosed weather proof (IP54) Feeder Pillar having 400 A bus bar as incomer and 3 no.160 A MCCB as outgoing, as per specifications. Type-B with mounting structure of minimum hieght of 750mm above ground level as per UPCL approved drawing.

Outdoor 400 Amp. 3 Phase LT bus bar type fully enclosed weather proof (IP54) Feeder Pillar having 400 Amps Al. bus bar as per specifications. Type-C with mounting structure of minimum hieght of 750mm above ground level as per UPCL approved drawing.

SUPPLY OF MATERIAL FOR SPECIAL EARTHING AS PER IS 3043-1987 WITH SOIL TREATMENT BY HIGHLY CONDUCTIVE MATERIAL (349 Nos)

GI pipe size 2500 mm x80 mm dia x 4 mm thick

Galvanized earth electrode of size 2575 x 20 mm

Epoxy Insulator (for earthing strip) 150 mm length x 72 mm withstanding voltage of 28 KV rms

Highly conductive chemical around electrode - Earth Enhancing Compound

Highly conductive substances for treatment of soil - Earth Enhancing Compound and additional ground resistance improvement chemicals

GI strip 50 x 6 mm (1.7 kg /mtr.) 6 mtr. long for connecting transformer body / neutral with earth electrode

Sundry items (Chrome plated M.S. bolt & nut with washers, Grease, Bitumen, Paint etc.)

SUPPLY OF MATERIAL FOR EARTHING WITH EARTH ROD FOR DTR PROTECTION CUBICALS AND LT FEEDER PILLARS (2852 Nos)

Earthing rod 20x2500 mm.

GI wire 6 SWG

Provisional Sum 1: Payments for approvals and permits for road cutting, construction and restoration works and associated charges payable to PWD, Nagar Nigam, NH etc for all 33 KV , 11kV & LT underground lines (To be paid as per actuals)

Provisional Sum 2: Payments for statutory clearances and approvals for execution of all works including clearances from Regulator/Electrical Inspector, Environmental and other concerned statutory authorities for construction, commissioning and operation of the facilities (To be paid as per actuals)

Monthly Operational Cost of fault locator & test van with driver and technician for 3 years

Description of Work / Item(s)

Amount

SCHEDULE A1 : 33 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES - CIVIL WORKS

For Cable Joints pits /termination chambers (64 Nos.)

Design & construction of joint pit / inspection chamber for 33 KV cables : conforming to specifications / guidelines of PWD Uttarakhand and approval including supply of civil materials, reinstatement of road / footpath surface as per PWD Uttarakhand requirements. (Estimated quantities are for max dimensions upto 3000 mm (w) x 3000 mm (l) x (h) 1200 mm whereas actual dimensions subject to space availability and approvals).

i) Excavation of earth in mixed soil

ii) Brick work 1:4

iii) MS bar 12 mm.

Fabrication of lid support mesh structure for Joint Pits using Galvanised M.S. Channel 125x65x6 mm. (85 kg per each lid)

For Ring main Unit (04 Nos)

Design & construction of 33 KV RMU foundation / footings conforming to Manufacturer's recommendation and UPCL / PWD Uttarakhand approval, including supply of civil materials.

i) Excavation of earth in mixed soil

iii) Brick work 1:4

iv) Cement plaster 1:4

Civil works for 33KV Bay equipments

For Terminal Gantry (02 No)

Fabrication of T.G. Structure (1972 Kg ) complete as per approved drawing.

Excavation of earth in mixed soil for foundation

Cement concreating in 1:3:6

Cement Plaster 1:4, on top & side walls

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

For Line isolator (02 Nos)

Fabrication of mounting structure (329 Kg ) as per approved drawing

Excavation of earth in mixed soil

Cement concreting in 1:3:6 ratio

Cement Plaster 1:4, on top & side walls

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

For Bus isolator (01 No)

Fabrication of mounting structure (329 Kg ) as per approved drawing

Excavation of earth in mixed soil

Cement concreting in 1:3:6 ratio

Cement Plaster 1:4, on top & side walls

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

For Vaccum Circuit Breaker (01 No)

Excavation of earth in mixed soil for foundation of CB stand

Grouting of CB stand with C.C. in 1:3:6 ratio

Cement Plaster 1:4, on top & side walls

For Current Transformer Set (01 Set)

Fabrication of mounting structure (163 Kg) as per approved drawing

Excavation of earth in mixed soil

Grouting of structure with C.C. in 1:3:6 ratio

Cement Plaster 1:4, on top & side walls

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

For Bus bar gantry (01 No)

Fabrication of gantry (818 Kg) for 33 KV bay including supports, busbars, insulators and connections complete.as per approved drawing.

Excavation of earth in mixed soil

Cement concreting in 1:3:6 ratio

Cement Plaster 1:4, on top & side walls

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

For Potential transformer set on Bus Gantry (01 Set)

Fabrication of mounting structure (77 Kg) as per approved drawing

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

For LT Control cable

Fabrication of MS structures (30 Kg/m)

Making cable trench of size 0.5 mtr wide x 0.6 mtr. depth including fabrication, fixing of MS angle 50x50x6 mm size (excluding the cost of MS Angle/ MS bar) on side edge with all excavation, CC work, brick work, fixing of cable support angle one/two tier as required with stopper arrangement at 0.5 mtr gap throughout the length of the trench, making of cable trench covers with MS Bar welded mesh angle frame of MS angle 40x40x5 mm. / 40x40x6 mm. with lifting hooks, fixing of perforated tray complete as per drawing including cost of sand, cement, bricks, metal (gitti) etc.

SCHEDULE A2 : 11 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES - CIVIL WORKS

For Cable Joins pits /Inspection chambers (212Nos)

Design & construction of joint pit / inspection chamber for 33 KV cables : conforming to specifications / guidelines of PWD Uttarakhand and approval including supply of civil materials, reinstatement of road / footpath surface as per PWD Uttarakhand requirements. (Estimated quantities are for max dimensions upto 3000 mm (w) x 3000 mm (l) x (h) 1200 mm whereas actual dimensions subject to space availability and approvals).

i) Excavation of earth in mixed soil

iii) Brick work 1:4

v) MS bar 12 mm.

viii) CC 1:1.5:3

Fabrication of lid support mesh structure for Joint Pits using Galvanised M.S. Channel 125x65x6 mm. (85 kg per each lid)

For Ring Main Unit Foundations (117 Nos)

Design & construction of 11 KV RMU foundation / footings includimg supply of civil materials conforming to Manufacturer's recommendation and UPCL / PWD Uttarakhand approval.

i) Excavation of earth in mixed soil

iii) Brick work 1:4

iv) Cement plaster 1:4

Fabrication & erection of GI foundation (using GI Channel 100x50x6 mm & GI angle 65x65x6 mm) structure with minimum height of 750 mm above ground level for 11 KV RMU as per approved design for places where civil foundation is not feasible including supply of GI channel & angle etc. (To be used where civil foundation is not feasible.)

SCHEDULE A3 : LT UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES - CIVIL WORKS

For RCC foundation of 11/0.433 KV 1000 KVA Compact Secondary Substation (20 Nos)

Design and erection of RCC foundation for 11/0.433 KV 1000 KVA Compact Secondary Substation as per manufacturer recommendation and approved drawing by UPCL including supply of all civil materials, complete.

i) Excavation of earth in mixed soil

iii) Brick work 1:4

iv) Cement plaster 1:4

vi) Filling of earth

Design and erection of RCC foundation (0.3 mtr. x0.3 mtr. x0.75 mtr. X 4 no. footings) for feeder Piller Type-A as per manufacturer recommendation and approved drawing by UPCL including supply of civil materials, complete.

Design and erection of RCC foundation (0.3 mtr. x0.3 mtr. x0.75 mtr. x4 no. footings) for feeder Piller Type-B as per manufacturer recommendation and approved drawing by UPCL including supply of civil materials, complete.

Description of Work / Item(s)

Amount

SCHEDULE A1: 33 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES – ERECTION

Manual digging of cable trench upto 1 mtr wide and 1.2 mtr deep in mixed soil having soft & hard soil like stone and road cutting areas and rocky terrain, backfilling and removal of excess earth from site, soil compaction as per PWD Uttarakhand norms.

Supply and Laying of HDPE pipe (PN-6, PE-80 of outer dia size 160 mm.) with coupler, short and long bends in open cut trenches IS :7634 Part -2 for installation of power cables as per the code of practice for installation and maintenance of power cables as per IS 1255 :1983 or latest amendments.

Supply and Laying of HDPE pipe (PN-6, PE-80 of outer dia size 160 mm.) with coupler, short and long bends at 1.2 to 1.5 mtr. deep using Horizontal Directional Drill (HDD) method including excavation of HDD drill pits and back filling, removal of excess earth from site including earth compression for installation of power cables as per the code of practice for installation and maintenance of power cables as per IS 1255 :1983 or latest amendments.

Laying and installing of 33KV XLPE HT cable 3Cx400 sq mm in HDPE pipe (in above sl. no. 1.102) as per the code of practice for installation and maintenance of power cables as per IS 1255 :1983 or latest amendments using motorised mechanical cable pullers, rollers for cable support, Hydraulic jack for cable drum etc. including cable marking & tagging, termination of cable on terminal gantry or RMU and final testing of HT cable

Laying and installing of 33KV XLPE HT cable 3Cx400 sq mm for cable loop using conventional method including soft sand cushioning 75mm. below and above cable, brick/CC tile protection layer, warning tape including including cable marking & tagging, supply of all civil materials, labour & T&P as per IS 1255 :1983 or latest amendments.

Erection of RCC Cable Duct, 850 mm wide as per drawings includig supply of all materials, fabrication and civil works.

Erection, testing and commissioning of 33 KV cable terminations & Straight through joints

33KV XLPE cable termination 3x400sqmm (Outdoor)

33 KV Premoulded screen connector suitable for 36 KV RMU for rating 1Rx3Cx400 sq.mm. as per RMU OEM recommendation

33KV XLPE cable straight through joint 3x400 sqmm including application of termite proofing on joint, sealing of ducts on both sides of the pit.

Laying of B-Class GI pipe 150 mm OD and 33 KV 3C x 400 sqmm cables, as per IS 1239, at culverts , crossings, by side of bridges with support hangers, fastners , complete in all respects.

Laying of B-Class GI pipe 150 mm OD and 33 KV 3C x 400 sqmm cables, as per IS 1239, at Road crossing complete in all respects.

Erection, Testing and commissioning of 33KV 630A 25kA/1 sec Outdoor Motorised SF6 insulated SCADA compatible Ring Main Unit with 3 nos. VCB Module as incoming/ outgoing (VVV) including, auxiliary power transformer, Fault Passage Indicator, and with suitable provisions to connect with FRTU.

Erection of equipment for 33 KV Bays

Erection of T.G. with LA and all accessories.

Erection of Line isolator including structure complete by assembeling, fixing of operating handle, pins etc for smooth operation of the isolator with control wiring including all accesores for terminal connections, earthing, etc. complete.

Erection of Bus-Isolator complete by assembeling, fixing of operating handle, pins etc for smooth operation of the isolator with control wiring including all accesores for terminal connections, earthing, etc. complete.

Fixing and erection of Vacuum circuit breaker along with mounting structure with control wiring including all accesores for terminal connections, earthing, etc. complete.

Fixing and erection of one set of CTs along with mounting structure with control wiring including all accesores for terminal connections, earthing, etc. complete.

Erection of Bus Gantry

Fixing and erection of one set of PTs along with mounting structure with control wiring including all accesores for terminal connections, earthing, etc. complete.

Erection charges for drawing Bus-bar , fixing connectors, insulators & making connection in each equipment, main & auxilary bus bar.

Erection, testing & commissioning of 33 KV C&R panel on specific location on MS Channel & fixing of panels with nut & bolt incl. electrical connection of panels by control wiring complete with & CB etc.

Laying, spreading & jointing of LT control cable including providing proper ties, lugs, connectors, cable glands in cable trench and equipments.

Erection of Special Chemical earthing

Digging of pit of size 1.2 X 1.2 X 0.2 mtr. in all types of soil

Further digging of pit of size 2500mm x 150 mm dia in all types of soil by drilling with help of tools & tackles as per drawings.

Fixing and positioning of GI pipe of size 2500 mm long x 80 mm dia x 4 mm thick as per drawings.

Fixing and positioning of earth electrode of sixe 2575 x 20 mm in the GI pipe as per drawing

Filling of highly conductive material (Earth Enhancing Compound) between residual gap of earth electrode & pipe

Filling / applying highly conductive substance (Earth Enhancing Compound and Ground Resistance Improvement Agent for treatment of soil) between residual gap of pipe & soil.

Fixing of epoxy insulated cover providing on the top of GI pipe for proper disipating.

Fixing of GI strip for connecting cable screen / armour with earth electrode along with digging & filling of trench for GI strip

Welding and other sundry works

Earthing Connection

Erection of GI earth strip 50x6 mm for connection of cable earth/earth bus/ body earth point with the earthing link of earthpit

Erection of Tinned Copper braid of size 50x6x1000 mm. with end lugs for earthing of HT cable

Dismantling of existing OH Lines & Poles

Dismantling of HT lines for all types of ACSR overhead lines (including of ACSR conductor, guarding wires) as instructed, transportation to central store and handing over to UPCL along with submission of videography and single line diagram prior to dismantling of existing infrastructure.

Dismantling of HT Poles of SP/DP/FP structures with all its accessories of HT lines, including insulators, stays wire & rods, transportation to central store and handing over to UPCL

SCHEDULE A2 : 11 KV UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES – ERECTION

Manual digging of cable trench upto 1 mtr wide and 1.2 mtr deep in mixed soil having soft & hard soil like stone and road cutting areas and in rocky terrains, back filling and removal of excess earth from site, soil compaction and reinstatement of road / footpath surface as per PWD Uttarakhand requirements and making good as original, including supply of all civil construction materials.

Supply and laying of HDPE pipe (PN-6, PE 80 of size 160 mm. OD) with coupler, short and long bends in open cut trenches and Laying of 11KV XLPE HT cable 3Cx300 sq mm in HDPE pipe as per the code of practice for installation and maintenance of power cables as per IS 1255 :1983 or latest amendments using motorised mechanical cable pullers, rollers for cable support, Hydraulic jack for cable drum etc. including termination of cable on terminal gantry or RMU and final testing of HT cable

Supply and Laying of HDPE pipe (PN-6, PE 80 of size 160 mm. OD) 1.2 to 1.5 mtr. deep using Horizontal Directional Drill method including excavation of HDD drill pits and back filling, removal of excess earth from site including earth compression and making good as original and laying and installation of 11 KV XLPE HT cable 3Cx300 sq mm in HDPE pipe (160 mm dia PN-6, PE 80) as per the code of practice for installation and maintenance of power cables as per IS 1255 :1983 or latest amendments using motorised mechanical cable pullers, rollers for cable support, Hydraulic jack for cable drum etc. including termination of cable on terminal gantry or RMU and final testing of HT cable

Laying and installing, testing & commissioning of 11 KV XLPE HT cable 3Cx400 sq mm in HDPE pipe (in above sl. no. 2.102) as per the code of practice for installation and maintenance of power cables as per IS 1255 :1983 or latest amendments using motorised mechanical cable pullers, rollers for cable support, Hydraulic jack for cable drum etc. including cable marking & tagging, termination of cable on terminal gantry or RMU and final testing of HT cable in

Supply and Laying and installing, testing & commissioning of 11 KV XLPE HT cable 3Cx400 sq mm for cable loop using conventional method including soft sand cushioning 75mm. below and above cable, brick/CC tile protection layer, warning tape including including cable marking & tagging, supply of all civil materials, labour & T&P as per IS 1255 :1983 or latest amendments.

Erection, testing and commissioning of 11 KV cable terminations/ Straight through joints

11KV XLPE cable termination 3x300sqmm (Outdoor)

11KV XLPE cable termination 3x300sqmm (Indoor)

11KV XLPE cable straight through joint 3x300sqmm including application of termite proofing on joint, sealing of ducts on both sides of the pit.

11KV XLPE cable termination 3x50sqmm (Outdoor)

11KV XLPE cable termination 3x50sqmm (Indoor)

Laying of B-Class GI pipe 150 mm OD and 11 KV 3C x 300 sqmm cable as IS 1239 at culverts, crossings, by side of bridges with support hangers, fastners, complete in all respects.

Laying of B-Class GI pipe 150 mm OD and 11 KV 3C x 300 sqmm cable as IS 1239 at Road crossingcomplete in all respects.

Erection, Testing and commissioning of 11 KV 630A 21kA/3 sec Outdoor motorised extendible type SF6 insulated Ring Main Unit with 2 No. Load Break Switch as incomer & Outgoing and 1 nos. VCB Module as outgoings for DTR (CCV) with auxiliary power module and suitable to connect with FRTU including FPIs.

Erection, testing & commissioning of 11 KV Extendible manual VCB functional unit for RMU (VCB) with interconnecting bus bar

Erection, testing & commissioning of 11 KV Extendible manual Load break switch functional unit for RMU (LBS) with interconnecting bus bar

Erection, testing & commissioning of 11 KV VCB FDR PANEL at existing s/s including providing of copper bus bar for extending bus bars of existing 11 KV feeder panels, adapter panel (if required), control and protection wiring, terminal connections and all associated work.

Erection of lightnng arresters and all accessories for each 11 KV cable riser and connection at existing terminal poles structures at substations.

Erection of Termination pole structure for new 11 KV feeders

Excavation of earth 2x(.45x.45x1.575)

Cement concreting of Double pole 1:4:8, 2x(.45x.45x1.8)

Fabrication of channels & angles

Erection of Double pole structure complete with all fittings, accessories, lightning arresters, stays & accosories.

Painting of structure with one coat of red oxide paint and two coats of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Erection of Special Chemical earthing as per IS 3043-1987 with Soil treatment by highly conductive material

Digging of pit of size 1.2X1.2X0.2 mtr. in each Type of soil

Further digging of pit of size 2500mm x 150 mm dia in each Type of soil by drilling with help of tools & tackles as per drawings.

Fixing and positioning of GI pipe of size 2500 mm long x 80 mm dia x 4 mm thick as per drawings.

Fixing and positioning of earth electrode of sixe 2575 x 20 mm in the GI pipe as per drawing

Filling of highly conductive material (Earth Enhancing Compound) between residual gap of earth electrode & pipe

Filling / applying highly conductive substance (Earth Enhancing Compound and Ground Resistance Improvement Agent for treatment of soil) between residual gap of pipe & soil.

Fixing of epoxy insulated cover providing on the top of GI pipe for proper disipating.

Fixing of GI strip 50x 6 mm (1.7kg / mtr.) 6 mtr. long for connecting Cable Screen / Armour via Tinned Copper braid, DTR / RMU body with earth electrode along with digging & filling of trench for GI strip

Welding and other sundry works

Earthing

Erection of GI earth strip 50x6 mm for connection of cable earth/ body earth point with the earthing link of earthpit

Erection of Tinned Copper braid of size 50x6x1000 mm. with end lugs for earthing of HT cable

Dismantling of existing OH Lines & Poles

Dismantling of HT lines for all types of ACSR overhead lines (including of ACSR conductor, guarding wires & 60 no. (approx.) DTRs which are to be relpaced by CSS) and transportation to central store and handing over to UPCL along with submission of videography and single line diagram prior to dismantling of existing infrastructure.

Dismantling of HT Poles of SP/DP/FP structure with all its accessories including insulators, stays wire & rods, stays wire & rod and transportation to central store and handing over to UPCL along with submission of videography and single line diagram prior to dismantling of existing infrastructure. Not applicable for composite poles with 33 KV.

SCHEDULE A3 : LT UNDERGROUND CABLE LINES AND ASSOCIATED FACILITIES - ERECTION

Manual digging of cable trench upto 0.6 mtr wide and 1.2 mtr deep in mixed soil having soft & hard soil like stone and road cutting areas and rocky terrain, backfilling including warning tape and ramming of excavated earth in trench , removal of excess earth from site, soil compaction as per PWD Uttarakhand norms (for main LT cables from DTR to A & B Feeder Pillar)

Erection of LT XLPE Alu. Armoured Cable 4C x 400 sq. mm. in HDPE pipes including tagging of LT cable at both ends..

Erection of LT XLPE Alu. Armoured Cable 4C x 400 sq. mm. for cable loop & termination using conventional method including soft sand cushioning 75mm. below and above cable, brick/CC tile protection layer, warning tape including including cable marking & tagging, supply of all civil materials, labour & T&P as per IS 1255 :1983 or latest amendments.

Erection of LT XLPE Alu. Armoured Cable 4C x 240 sq. mm. in HDPE pipes including tagging of LT cable at both ends.

Erection of LT XLPE Alu. Armoured Cable 4C x 240 sq. mm. for cable loop & termination using conventional method including soft sand cushioning 75mm. below and above cable, brick/CC tile protection layer, warning tape including including cable marking & tagging, supply of all civil materials, labour & T&P as per IS 1255 :1983 or latest amendments.

Erection of LT XLPE Alu. Armoured Cable 4C x 120 sq. mm. in HDPE pipes including tagging of LT cable at both ends.

Erection of LT XLPE Alu. Armoured Cable 4C x 120 sq. mm. for cable loop & termination using conventional method including soft sand cushioning 75mm. below and above cable, brick/CC tile protection layer, warning tape including including cable marking & tagging, supply of all civil materials, labour & T&P as per IS 1255 :1983 or latest amendments.

Erection of LT XLPE Alu. Armoured Cable 4 x 95 sq.mm. (for load 26-75 KW) in HDPE pipes including tagging of LT cable at both ends.

Erection of LT XLPE Alu. Armoured Cable 4 x 95 sq.mm. (for load 26-75 KW) for cable loop & termination using conventional method including soft sand cushioning 75mm. below and above cable, brick/CC tile protection layer, warning tape including including cable marking & tagging, supply of all civil materials, labour & T&P as per IS 1255 :1983 or latest amendments.

Erection of LT XLPE Alu. Armoured Cable 4 x 16 sq.mm. (for load 5-25 KW) in HDPE pipes including tagging of LT cable at both ends

Erection of LT XLPE Alu. Armoured Cable 2 x 10 sq.mm. (for load upto 4 KW) inside HDPE pipes including tagging of LT cable at both

Erection of LT cable termination kit for LT XLPE armoured Cable 4C x 400 sq.mm.

Erection of LT cable termination kit for LT XLPE armoured Cable 4C x 240 sq.mm.

Erection of LT cable termination kit for LT XLPE armoured Cable 4C x 120 sq.mm.

Erection of LT cable termination kit for LT XLPE armoured Cable 4C x 95 sq.mm.

Erection of Straight Through Joint LT Outdoor Type 4C x 400 sq. mm.

Erection of Straight Through Joint LT Outdoor Type 4C x 240 sq. mm.

Erection of Straight Through Joint LT Outdoor Type 4C x 120 sq. mm.

Erection of 400 sq. mm. Long barrel Al Lugs for 4Cx 400 sqmm cable

Erection of 240 sq. mm. LT Long barrel Al Lugs for 4C x 240 sqmm cable

Erection of 120 sq. mm. Long barrel Al Lugs for 4C x 120 sqmm cable

Erection of 95 sq. mm. Long barrel Al Lugs

Erection of 16 sq. mm. Long barrel Al Lugs

Erection of 10 sq. mm. Long barrel Al Lugs

Erection of double compression Al LT Glands for 400 sq. mm.. Cable

Erection of double compression Al LT Glands for 240 sq. mm.. Cable

Erection of double compression Al LT Glands for 120 sq. mm. Cable.

Erection of double compression Al LT Glands for 95 sq. mm. Cable.

Erection of double compression Al LT Glands for 16 sq. mm. Cable.

Erection of double compression Al LT Glands for 10 sq. mm. Cable.

Erection of Copper braid/bond for earthing of size 50x6x1000 mm. (for earthing of main LT cable)

Supply and Erection of 160 mm. HDPE Pipe with coupler, short and long bends including providing & fixing of cleats for HDPE pipe wherever required

Supply and Erection of 110 mm. HDPE Pipe with coupler, short and long bends including providing & fixing of cleats for HDPE pipe wherever required

Supply and Erection of 50 mm. HDPE Pipe with coupler, short and long bends including providing & fixing of cleats for HDPE pipe wherever required

Erection of Concrete route marker for LT cable

Erection of Polycarbonate box for meter including dismantling of damaged / replaceable meter box for 1 Phase meter

Erection of Polycarbonate box for meter including dismantling of damaged / replaceable meter box for 3 Phase meter

Erection of LT PRMC including instrument wiring, for connecting with load 26-75 KW including dismantling of damaged LT PRMC including providing of all misc. material for erection work of PRMC

Manual digging of cable trench upto 0.6 mtr wide and 0.6 mtr deep in mixed soil having soft & hard soil like stone and road cutting areas and rocky terrain, back filling and ramming of excavated earth in trench after laying of required number of HDPE pipes as per UPCL instructions, removal of excess earth from site, soil compaction as per PWD Uttarakhand norms (for service connections cables)

Providing consumer service connection for load upto 4 kw at consumer premises with proper connections including mounting of meter and tagging of consumer service connectin number at both ends.

Providing consumer service connection for load upto 5-25 kw at consumer premises with proper connections including mounting of meter and tagging of consumer service connectin number at both ends.

Providing consumer service connection for load upto 26-75 kw at consumer premises with proper connections including mounting of meter with metering cubical and tagging of consumer service connectin number at both ends

Erection of LT metering cubical of 160 A capacity 3-ph main bus bar with locking provision & 10 nos meter cubicals to install three phase meters with associated mounting structure complete foundation work as per UPCL instructions.

Laying of B-Class GI pipe 150 mm at culverts , crossings, by side of bridges with support hangers, fastners , complete in all respects.

Laying of B-Class GI pipe 150 mm at Road crossing complete in all respects.

Termination of LT main cable on STP/PCC/Rail pole using holding clamp complete work for connecting overhead LT line.

Erection of one set of 9 KV 10 KA Lightening Arresters on DP structure and all works and connections complete.

Erection of Bus Isolator on DP structure including fabrication charges, all works and connections complete.

Erection of HT fuse Set (Horn Gap) on DP structure including all works and connections complete.

Erection of LT protection panels with LT ACB and mounting structure including CC works (0.3 mtr. x0.3 mtr. x0.75 mtr. x4 no.), as per UPCL specification in existing 400/250/160 KVA DTR installations including removal of and handing over to UPCL any existing / unserviceable equipment, and all works and connections complete.

Erection of LT protection panels with LT MCCB , as per UPCL specification in existing 100, 63 and 25 KVA DTR installations including removal of and handing over to UPCL any existing / unserviceable equipment, and all works and connections complete.

Erection of 11/0.433 KV, 1000kVA Compact Secondary Substation (CSS) including all works, connections and earthing, complete.

Erection of feeder Piller Type-A with mounting structure as per UPCL approved drawing, including all works and connections complete.

Erection of feeder Piller Type-B with mounting structure as per UPCL approved drawing, including all works and connections complete.

Erection of feeder Piller Type-C with mounting structure as per UPCL approved drawing, including all works and connections complete.

Erection of Special Chemical earthing

Digging of pit of size 1.2X1.2X0.2 mtr. in each Type of soil

Further digging of pit of size 2500mm x 150 mm dia in each Type of soil by drilling with help of tools & tackles as per drawings.

Fixing and positioning of GI pipe of size 2500 mm long x 80 mm dia x 4 mm thick as per drawings.

Fixing and positioning of earth electrode of sixe 2575 x 20 mm in the GI pipe as per drawing

Filling of highly conductive material (Earth Enhancing Compound) between residual gap of earth electrode & pipe

Filling / applying highly conductive substance (Earth Enhancing Compound and Ground Resistance Improvement Agent for treatment of soil) between residual gap of pipe & soil.

Fixing of epoxy insulated cover providing on the top of GI pipe for proper disipating.

Fixing of GI strip for connecting T/F body /neutral/cable with earth electrode along with digging & filling of trench for GI strip

Welding and other sundry works

Erection of Earthing with earth rod 20x2500 mm.

Erection and Earthing of support with M.S. Earth rod of 2.5 meter long including excavation of pit and digging of M.S. Rod to proper depth and connecting the earth electrode with the help of G.I. wire as per UPCL instructions.

Dismantling of existing OH Lines & Poles

Dismantling of LT lines for all types of ACSR / AAC / ABC overhead lines and transportation to central store and handing over to UPCL along with submission of videography and single line diagram prior to dismantling of existing infrastructure.

Dismantling of ST Poles of SP/DP/FP structure with all its accessories, including insulators, stays wire & rod and transportation to central store and handing over to UPCL along with submission of videography and single line diagram prior to dismantling of existing infrastructure. Not applicable for composite poles with 11 KV & 33 KV

Dismantling of PCC Poles removal of debris to suitable place and clearing of site along with submission of videography and single line diagram prior to dismantling of existing infrastructure.

Description of Work / Item(s)

Amount

Total Price CIP in EUR (Schedule 1)

Total Price CIP in USD (Schedule 1)

Total Price CIP in JPY (Schedule 1)

Total Price of Import Duty in INR (Schedule 1)

Total Price EXW in INR (Schedule-2)

Total Price of Design Services in INR ( Schedule-3)

Total Price of Incidental Expenses in INR( Schedule-4A)

Total Price of Civil Works in INR(Schedule - 4B)

Total Price of Erection including Testing and Commissioning in INR(Schedule - 4C)

Capital Electech Pvt Ltd

KEI Industries Limited

Capital Electech Pvt Ltd

Capital Electech Pvt Ltd

KEI Industries Limited

Capital Electech Pvt Ltd

KEI Industries Limited

US Dollar

European Euro

Japanese Yen

US Dollar

European Euro

Japanese Yen

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

US Dollar

European Euro

Japanese Yen

CLP-HDPE-160

RSJ-TP-A

RSJ-6-TP

WC-PTP

WC-PTD

C-CTPT-P

C-VCB-P

RCP-SF-NSC

SNDR-ITM-1

CFL-TV

SF6-RMU-11

CLP-GIP-1

CLP11-STP-1

GI-SWG-1

GI-E-LA

CLP11-STP-2

CLP-HCSA-TPMO

SNDR-ITM-2

SF6-KIT

XLPE-LT-400

XLPE-LT-240

XLPE-LT-120

XLPE-LT-95

XLPE-LT-16

XLPE-LT-10

LT-CTK-400

LT-CTK-240

LT-CTK-120

LT-CTKB-95

STJ-XLPE-400

STJ-XLPE-240

STJ-XLPE-120

LT-AIL-400

LT-AIL-240

LT-AIL-120

LT-AIL-95

LT-AIL-16

LT-AIL-10

DCG-XLPE-400

DCG-XLPE-240

DCG-XLPE-120

DCG-XLPE-95

DCG-XLPE-16

DCG-XLPE-10

CRM-HT-3

PCB-CEM1

PCB-CEM3

LT-PRMC

HCLP-BC-GIP

CLP-LT1

CLP-LT2

XLPE-LT1C-630

XLPE-LT1C-400

XLPE-LT1C-240

LT-MCCB-250

FDRP-A

FDRP-B

FDRP-C

SNDR-ITM-3

GI-SWG-2

RSJ-TP-A

RSJ-6-TP

CLP11-STP-2

SNDR-ITM-2

CRM-HT-3

CLP-LT2

SNDR-ITM-3

GI-SWG-2