Muziris Heritage Project - Development of Munakkal Beach at Azhikode Thrissur (SH Civil and Electrical works)

Amount

FOOT PATH, DRAINS, KERBS AND ALLIED

2.6.1 : Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

od96801/2020_2021 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 20 nominal size)

50.5.33.2 : Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.Note:- Cement content considered in this item is @ 330 kg/cum. Excess or less cement used as per design mix is payable or recoverable separately. All work above plinth level upto floor V level

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.22A.4 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Hot rolled deformed bars

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

16.69 : Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

16.91.1 : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 grade with approved colour, design& pattern.

od96811/2020_2021 : Filling in below paver block to line and level as directed by the Engineer-in Charge , including watering, ramming consolidating and dressing complete with available sand from site. (Rate derived from DSR item 2.27)

od96813/2020_2021 : Providing wall lining over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with required colour etc. complete as directed by Engineer- in-Charge<br>Leather finished Granite

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

19.7.3.2 : Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 120x 90 cm and 90 cm deep including C.I. cover with frame ( heavy duty ) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg ( weight of cover 108 kg and weight of frame 100 kg)With Sewer bricks conforming to IS: 4885

10.26.1 : Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

od115704/2020_2021 : Providing Benches in landscape area In RCC M20 grade concrete as per detailed drawing and including plastering with CM 1:6 , 6mm thick, Topping with leather finish granite 12mm thick in seating area and back support, painting with synthetic enamel paint in other visible portions etc. complete as directed by Engineer in charge.

ROOFING

12.48 : Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately)

od96802/2020_2021 : Providing and laying MP hip and ridge tiles with class AA Mangalore pattern tiles (COMTRUST) manufactured by M/s Common Wealth Trust Ltd., or equivalent including fixing with cement mortar 1:2 (1 cement : 2 coarse sand ) as directed by Engineer-in-Charge at all levels. <br><br>

od96805/2020_2021 : Providing & fixing on ceiling factory pressed clay decorative floral tile (under mangalore tile roof) of 320mm x 200 mm x 12mm and as per approved pattern on timber frame work complete including extra lowering charge and scaffolding charges as directed by Engineer-in-Charge.(Timber frame work to be paid separately).

LANDSCAPING

2.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

30.2.2 : Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.25 : Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m. lead complete (cattle manure measured in stacks will reduced by 8% for Payment).

30.2.8 : Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

30.2.28 : Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.

30.2.33 : Providing and fixing Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and even, watering with sprinkler

od96809/2020_2021 : Supply and stacking of konna / Cassia fistula (Amaltash) plant of height 120-135cm. in big poly bags of size 25 cm as per direction of the officer-in charge - landscaping works

od96810/2020_2021 : Providing of Areca palm plant, having ht. 1.50 m to 1.80 m with 6 to 8 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot / Plastic pot

od96812/2020_2021 : Supply and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara, Mohan, Scarlet Queen, Varigata, Glabra Formosa, Peruviana, Odissi, Partha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) plant of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge - landscaping works

od96814/2020_2021 : Supply and stacking of plant Arali / Nerium oleander variegated of height<br>60-75cm., multibranched in earthen pots of size 25 cm as per direction of<br>the officer-in-charge - landscaping works

od96815/2020_2021 : Supply and stacking of plant nandyarvattam / Tabernaemontana divaricata (Chandni double) of height 45-60 cm in earthen pots of size 20 cm as per direction of the officer-in-charge - landscaping works

od332432/2020_2021 : Supply and stacking of Ficus religiosa (Pepal) of plants height 150-165 cm. in big poly bags of plants size 30 cm as per direction of the officer-in-charge.

od332433/2020_2021 : Supply and stacking of Plumeria alba of plants height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

od96816/2020_2021 : Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable materials as per direction of officer in charge (excluding cast of plant & water ) Cost of plantation per trees plants

30.2.39.6 : Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, hedge, flower beds, foliages, creepers etc. including hoeing, weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide , lawn mover and brush cutter with fuel will be provided by the Department & other T & P material/articles shall be provided by the contractor.)and as per direction of officer in charge.Open spaces (3.00 Acre=One Mali)As per yard stick

MASONRY

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.6.1.1 : Solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

FLOORING WORK

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

od96803/2020_2021 : Supplying and fixing 40 mm thick two line dressed Saderhally grey granite stone of size 300x300mm over a layer of 6mm aggregate 75mm thick. The 20mm wide joints shall be filled with PCC 1:1.5:3 using 6mm aggregates and finished with ruled pointing using CM 1:3. The edges of granite shall be 10-15mm machine cut from top and bottom side and the rest area shall be dressed vertically .The rate shall include labour charges for granite fixing and cutting to size,stone dressing charges , cost and conveyance of all materials,lead, lift, etc. complete as per drawings and as directed the Engineer-in Charge at all levels.(The sample shall be approved by the Architect)

od96806/2020_2021 : Providing edge moulding to 18 mm double thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

FINISHING

13.8.2 : 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix:1: 4 ( 1 cement : 4 fine sand)

Guard Post

55.16 : Providing and fixing guard post<br>Providing and fixing guard post of size 200mmx200mm, 1400mm long, 800mm above ground level and 600mm below GL. casted in M20 Grade concrete reinforced with 4 nos of 8mm dia longitudinal bars and 6mm dia stirrups @ 100mm c/c, firmly fixed in position by means of foundation of size 0.5mx0.5mx0.7m in M15 grade concrete below ground level including painting 2 coats on exposed surface with synthetic enamel paint in alternate white & black band 20cm wide

Others

od97924/2020_2021 : Providing Sundial as directed by Engineer- in-Charge including lifting,conveyance and finishing etc.,

ELECTRICAL WORKS

od329897/2020_2021 : Fabrication, Supply, Installation, testing &amp; Commissioning of IP65 rated Lockable type energy Meter cubicle made out of 16 SWG CRCA sheet with view glass and consisting of following (Complete with all interconnections and powder coated painting - to be fixed outside the building) including Necessary Liasoning works for getting Electrical&lt;br&gt;Connection &amp; Other Approvals as required and directed by Engineer in charge &lt;br&gt;a. Separate chamber for 3-Ph energy meter, Cutouts etc.&lt;br&gt;b. 1 No. 63A FP Isolator &amp; 3 no of HRC Fuse with base

od331067/2020_2021 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415V, TPN MCCB distribution board of sheet steel, dust protected, duly powder painted inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB&apos;s (but without MCB&apos;s and incomer ) as required &bull; (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.).8 way (4 + 24), Double door

od331068/2020_2021 : Supply and fixing Following size FP MCCB with thermal magnetic protection unit, with O/L &amp; S/C protection in the existing VTPN DB, with all accessories and connections as required. 63A, 16kA MCCB

2.10.4 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole

od331075/2020_2021 : Supply and fixing of following FP 415V, isolators in IP65 rated sheet steel powder coated enclosure with door interlock and padlock facility on surface confirming to IEC 60947-3 complete with all accesories, connections, testing and commissioning etc as required and as instructed by engineer in charge also making good any damages made during installation.&lt;br&gt;32A FP Isolator with enclosure&lt;br&gt;

od325817/2020_2021 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armored Aluminium&lt;br&gt;conductor,A2XFY power cable confirming to IS 7098 (part 1) amended upto date. 4cx25sq.mm Al Cable

od325818/2020_2021 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armored Aluminium&lt;br&gt;conductor,A2XFY power cable confirming to IS 7098 (part 1) amended upto date 4cx16sq.mm Al&lt;br&gt;Cable&lt;br&gt;

od325832/2020_2021 : Supply of the following size 1.1kV grade XLPE insulated PVC sheathed, armored Aluminium&lt;br&gt;conductor,A2XFY power cable confirming to IS 7098 (part 1) amended upto date 4cx10sq.mm Al&lt;br&gt;Cable&lt;br&gt;

7.1.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm

7.5.1 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Upto 35 sq. mm

9.1.32 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

od325860/2020_2021 : Supply &amp; laying of HDPE pipe in all kind of soil 0.75 meter below ground level including excavation and refilling the trench as required

od325885/2020_2021 : Supply, installation, testing and commissioning of Decorative Column 3.0 metre height above the ground level made out of GI, tubular pole with 27 watts LED light, &lsquo;T&rsquo; washed and primered. (ASTM A123, with minimum average GI coating of 65&mu;m.), having two sections, bottom section of minimum 1000mm (L) x 140mm dia and the top section with minimum of 2000mm (L) x 76mm dia, in built junction looping box at bottom section with 32 A heavy duty 4 way connector for loop in &amp; loop out. The Embellishments are cast in iron and fitted to the column by grubs screw fitting. Design comply EN40 standard and basic wind speed 169 kmph. The embellishments shall be sealed to the column. The Pole Base plate should be with 250x250x12 mm. The column shall also be provided with flush door at the bottom with proper strengthening to the cut-out of the door opening. The column should be given with two coats of epoxy primer and above that it should be given with polyurethane UV resistant coating (painted with avg. DFT of 70&mu;m), marine grade coating. The complete system should be hot dipped Galvanised treated. The cost also inclusive of necessary RCC/PCC foundation as per the reccomendation of pole manufacturer.&lt;br&gt;Light fixture : Philips:BGP161/ Equivalent Wipro make&lt;br&gt;Pole Make : Autocast or Equivalent

od325912/2020_2021 : Earthing with G.I. earth pipe 3 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but with charcoal &amp; coke) as required.

90.16.1.3 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required

od329148/2020_2021 : Dismantling of existing defective lamps from the existing Poles and SITC of 36W LED Streetlight of approved make(Philips/Wipro/Equivalent) Similar to Luker Make model No:LS36 or equivalent with all connections and interconnections and control wirings with accessories as required.

Radhakrishnan M P

Bidder Name

T K UBAIDULLA, UBAID ASSOCIATES

Radhakrishnan M P