Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L-1₹12.4 CrAccepted-AOC | ₹12.4 Cr | L-1 | Accepted-AOC Being lowest |
| 2 | L-2₹12.4 CrRejected-AOC | ₹12.4 Cr | L-2 | Rejected-AOC Not found lowest |
| 3 | L-3₹13.1 CrRejected-Finance | ₹13.1 Cr | L-3 | Rejected-Finance Not found lowest |
| 4 | L-4₹13.6 CrRejected-Finance | ₹13.6 Cr | L-4 | Rejected-Finance Not found lowest |
| 5 | L-5₹15.7 CrRejected-Finance | ₹15.7 Cr | L-5 | Rejected-Finance Not found lowest |
Tender Value
₹13.2 Cr
EMD Value
₹23.2 L
Closing Date
8 Dec 2021, 10:30 amClosed
Executive Engineer
O/O Executive Engineer Sunder Nagar Division HPPWD Sundenagar, Distt. Mandi (HP)
SH C/o building portion water supply and sanitary installation RWHS and site development.
2021_PWD_54056_1
PW-SNR-CB-E-Tender/20-9707-13 dt. 24.11.2021
Open Tender
Civil Works - Buildings
730 days
Sundernagar
As per bid document
14 documents required · 14 mandatory
₹5,000
EE Sundernagar
₹23.2 L
1 Apr 2022
29 Nov 2021
8 Dec 2021
29 Nov 2021
8 Dec 2021
29 Nov 2021
Amount
Cutting in earth work all kinds of soils and disposal of excavated earth upto a lead of any metres such as pick work , jumper work, pick work,pick jumper blasting work, blasting work in soft and hard rock conglomrate rock or saturated soil and its intermediate classification of soil including chiseling/ wedging out of rocks (where blasting is prohibited) and pumping or bailing out of watering/ dewatering upto any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.
Excavation in foundation trenches etc. in earth work in all kinds of soils such as pick work , jumper work, pick work,pick jumper blasting work, blasting work in soft and hard rock conglomrate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing out of watering/dewatering upto any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.
Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:3:6 (one cement : three coarse sand) : six graded stone aggregate) 20 mm ( twenty millimetre nominal size including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing weep holes in brick masonry/ stone masonry plain reinforced concrete retaining/ breast wall with 100mm( one hundred millimetre) dia PVC pipe extending through the full with of the structure with slop of 1 (V):20(H) towards drawing face complete as per drawing and technical specification including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Back filling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 including carriage of material within all leads and lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately). All works upto plinth level including carriage of materials with in all leads, lifts and other incidentals
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level complete including cost of binding wire up to any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.With material conforming to Grade-I (size range 75 mm to 0.075 mm)( seventy five millietre to zero point zero seventy five millimetre ) having CBR Value-30 including carriage of materials with in all leads, lifts and other incidentals.
Stone masonry in cement mortar for sub structure complete as per drawing and technical specification clause 702,704, 1202 and 1204 in Cement mortar 1:4(one Cement : four sand) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying reinforced cement concrete 1:1.5:3 (one cement : one and half Sand :three graded stone aggregate 20mm ( twenty millimetre ) nominal size mechanically mixed and vibrated to give an smooth and even surface including centring and shuttering etc upto all level but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .
Reinforced cement concrete work in walls (any thickness),1:1.5:3 (one cement : one point five coarse sand) : three graded stone aggregate 20 mm( twenty millimetre ) nominal size)including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (one cement : three coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20 mm( twenty millimetre ) nominal size)including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying Flooring laid over cement concrete bedding complete as per drawing and Technical specifications clause 1303 including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm ( six hundred millimete ) with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8 including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Drainage spout complete as per drawing and technical specification including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Supplying and filling in plinth with sand under floors,including watering, ramming, consolidating and dressingcomplete.S upplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressingcomplete. including carriage of materials with in all leads, lifts and other incidentals..
Stone soling/boulder filling dry hand packed in under floor as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
CONCRETE WORK: Providing and laying in position cement concrete 1:5:10 (one cement : five coarse sand): ten graded stone aggregate 40 mm ( forty millimetre ) nominal size of specified grade) excluding the cost of centering and shuttering including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying in position cement concrete 1:4:8 (one Cement : four coarse sand : eight graded stone aggregate 40 mm( forty millimetre ) nominal size of specified grade excluding the cost of centering and shuttering as per direction of Engineer - in - charge .
Providing and laying damp-proof course 40mm ( forty millimetre thick with cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 12.5mm ( twelve point five millimetre ) nominal size including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing & applying a coat of residual petroleum bitumen of grade of VG-10(ten) of approved quality using 1.7 kg ( one point seven kilo grame ) per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oilincluding carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Making plinth protection 50mm thick of cement concrete 1:3:6 (one cement : three coarse sand : six graded stone aggregate 20 mm( twenty millimetre ) nominal size over 75mm( seventy five millimetre ) thick bed of dry brick ballast 40 mm ( forty milimetre ) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm ( fifteen x twenty two centimetre ) in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size and 7.5cm ( seven point five centimetre ) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
FORM WORK & RCC WORK: Centering and shuttering including strutting, propping etc. and removal of form work for:-
Foundation, footing basis of columns etc. and mass concrete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Beams, cantilever, girders and lintels sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels in any depth in all height from floor including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Stair cases with sloping or stepped soffits excluding landing including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Edges of slabs and breaks in floors and walls in any width including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Encasing Rolled Steel Sections in beams and columns with machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability including centring and shuttering complete but excluding cost of reinforcement as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.
Providing, fabricating, transporting, assembling and erection in position of Steel members for steel columns, beams using built up section plate, girders, etc., Yield strength 410 MPa as per latest IS code to the required profile & shape as called for as per the drawing & specifications. This item also includes the shear connectors/ studs & fusion weld to the top of horizontal member. This item also includes preparation of shop drawings & their approval, necessary templates, adequate temporary supports, scaffolding & staging, all cutting, grinding, sliding & all labour, tools, plants & equipment & operations etc. required to complete the job as per drawing and specification. Every precaution to be taken to prevent rusting of sections. This item also includes all test on materials & welded fabricated parts as per specification & direction of Engineer-in-Charge. Temporary bolts & nuts (grade EN 8) to be used during assembling & shall be removed before site erection. All site erection bolts shall be HSFG type only. The item to include cost of sand blasting on materials, application of primer & various coats of internal & external painting in fabrication shop & final application on site including all touch up works after erection as per technical specification and as per direction of Engineer - in - charge .
The scope of work for this item includes: a) Design & fabrication of any additional temporary structure including all type of lifting brackets, supporting brackets, which will be required for transportation & erection in position/ launching of fabrication part or complete element in position .
b) Making provision & arrangement for required opening/inserts for fixing light fixtures and funning cable conduits.
c) All incidentials, labour, equipment & plants required to execute & complete the job from fabrication to erection at final position as per drawing , specification .
d) Cleaning and removing of all spoil, temporary arrangement for casting of deck slab.
e) All safety measures required to execute and complete the work.
g) The provision of temporary bearing/sand jacks for supporting steel members during erection.
h) Provision of Stability during erection against wind load or any other type of loading on structural steel members during erection.
Providing and fixing in positioning of high strength structural bolts (Property class 8.8/10.9 as per IS:1367 and product grade ‘C’ as per IS:1363) confirming to IS:3757 and high strength structural hardened and tempered nuts (Property class ‘8’/10 as per IS:1367) confirming to IS:6623 with hardened and tempered washers as per IS 6649 etc., up to and inclusive of 39 mm ( thirty nine millimetre ) diameter and 300 mm( three hundred millimetre ) long including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works above plinth level up to Floor-any Level
BRICK WORK Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor any level in all shapes and sizes including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor any level. Cement mortar 1:3 (one cement : three coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm /300 mm ( one hundred fifty / two hundred thiorty / three hundred millimetre ) thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
STONE WORK Coursed rubble masonry (second sort) with hard stone in foundation & plinth with :Cement mortar 1:6 (one cement : six coarse sand) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
MARBLE AND GRANITE STONE Providing and fixing specified wood frame work consisting of battens 50x25mm ( fifty x twenty five millimetre ) fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete :Second Class Deodar wood including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing 18 mm ( eighteen millimetre ) thick gang saw cut,mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills,facias and similar locations of required size, approved shade, colour and texture laid over 20 mm ( twenty millimtre) thick base cement mortar 1:4 (one cement : four coarse sand), joints treated with white cement, mixed with matching pigment,epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc .complete at all levels: Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble :Area of slab over 0.50 sqm including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed surface, with necessary fixing arrangement and screws etc. complete :12 mm ( twelve millimetre ) thick including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Decorative first class kiln seasoned teak wood beading out of 25x12mm ( twemty five x twelve millimetre ) section with wood screws in ceiling and linning/panelling including mitring at junctions and to be polished including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Decorative first class kiln seasoned teak wood cornice out of 75x60mm (seventy five x sixty millimetre )section with wood screws in ceiling and linning/panelling including mitring at junctions and to be polished including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
WOOD AND P.V.C. WORK: Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm ( four millimetre ) thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 35 mm ( thirty five millimetre ) thick including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3(three) ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm ( thirty five millimetre ) thick including ISI marked Stainless Steel butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals.
Extra for providing lipping with 2nd class teak wood battens 25 mm ( twenty five millimetre )minimum depth on all edges of flush door shutters (over all area of door shutter to be measured) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Extra for providing vision panel not exceeding 0.1 sqm( zero point one square metre ) in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Pre-laminated flat pressed 3( three) layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately) 18 mm ( eighteen millimetre ) thick including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing 18 mm ( eighteen mellimetre ) thick, 150 mm ( one hundred fifty millimetre ) wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm( six millimetre ) coir veneer board, nickle plated M.S. Pipe 20 mm ( twenty millimetre) dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm ( twenty five x three millimetre ) M.S. Flat 10 cm ( ten centimetre ) long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm ( one hundred x forty x forty millimetre ) on both inner side of pelmet and rawl plugs 75 mm ( seventy five millimetre ) long etc. all complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing M.S. grills of required pattern inframes of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing 40x5 mm ( forty x five millimetre) flat iron hold fast 40 cm long including fixing to frame with 10 mm( ten millimete ) diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm ( thirty x ten x fifteen centimetre ) 1:3:6 mix (one cement : three coarse sand : six graded stone aggregate 20mm ( twenty millimetre) nominal size) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing 150mm (one hundred fifty millimeter) oxidized M.S. single acting spring hinges with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. .
Providing and fixing M.S sliding door bolt of approved quality with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .
Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
200x10mm (Two hundred x ten millimeter)
150x10mm (One hundred fifty x ten millimeter)
100x10mm (One hundred x ten millimeter)
Providing and fixing M.S. handles of approved quality with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.
125 mm (One hundred x twenty five millimeter)
100 mm (One hundred millimeter)
75 mm (seventy five millimeter)
Providing and fixing bright finished brass 100mm.(One hundred millimeter) Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. .
Providing and fixing 115mm (one hundred fifteen millimeter) bright finished brass heaps and stapples (safety type) with necessary screws etc complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing 19mm ( nineteen millimetre ) thick water proof termite resistant ply wood of Uniply/ Greenply or Century Ply including shelves and shutters.The back side of cup boar/cabinet shall be 8mm thick MDF as per detail in drawing .All internal surface of Cup board shall be laminated with 1mm mica of approved shade, including piano hinges and magnetic catcher with in all accessories etc. complete as per detailed drawing as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc.complete :300x16 mm ( three hundred x sixteen millimetre ) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing aluminium tower bolts, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :300x10 mm ( three hundred x ten millimetre ) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm ( three hundred twenty five millimetre ) including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. Complete: Single rubber stopper including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm ( fifty x fifty x one point six millimetre) hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm ( sixty centimetre ) centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm ( eight millimetre ) dia, 75 mm ( seventy five millimetre) long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing 8mm( eight millimetre) thick Action tesa clip in prelaminated wooden flooring (H.D.F) with poly sheet & thermocoal sheet with door profile and side moulding locks with all fittings ,etc. complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.
Providing ,supplying and fixing HPL Pannels of approved brand and manufacture on aluminium extruded tubuiar and other aluminium sections including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. ( The Aluminium frame work as for /NCL frame work IGUs shal be paid for separately) including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in?charge . (Cost of SS ball bearing hinges is excluded including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing 60 mm ( sixty millimetre ) thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of directions of Engineer - in charge (panelling to be paid for separatelt) including carriage of materials with in all leads, lifts and other incidentals.
STEEL WORK Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in positiobn and applying a priming coat of red lead paint as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm ( twenty seven point five centimetre ) long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.: 80x1.25 mm ( eighty x one point twenty five millimetre ) M.S. laths with 1.25 mm (one point twenty five millimetre ) thick top cover including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing ball bearing for rolling shutters including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Extra for providing mechanical device chain and crank operation for operating rolling shutters : Exceeding 10.00 sqm( ten square metre ) and upto 16.80 sqm ( sixteen point eighty square metre ) in the area including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing mild steel round holding down bolts with nuts and washer plates complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 40x40x5 mm, ( forty x forty x five millimetre ) joints mitred and welded by angle iron 40x40x5 mm (forty x forty x five millimetre ) or 35x 5 mm or ( thirty five x five millimetre ) flat pieces to the existing T iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing M.S. Channel door,window,clerestory window frame manufactured from M.S. section ISLC 40x75mm ( fortyx seventy five millimetre ) & M.S flat 40x12mm ( forty x twelve millimetre ) in combination welded together to make one frame including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 50X25 mm ( fifty x twenty five millimetre ) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including bright finished or black enamelled mild steel butt hinges 100x58x1.90 mm ( one hundred x fifty eight x one point ninety millimetre ) with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface with in all leads and lifts as directed by Engineer-in- Charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing staircase railing and similar works, including applying priming coat of approved steel primer.M.S. tube including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Decorative first class kiln seasoned teak wood Hand rail out of 75x60mm ( seventy five x sixty millimetre) section with wood screws in staircase including mitring at junctions and to be polished including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing M.S. BP Sheet1.66 mm(One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete as per direction of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.
FLOORING Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm ( forty millimetre ) thick with 20 mm ( twenty millimetre ) nominal size stone aggregate. including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying full body Vitrified tiles out of single piece riser 20X150cm ( twenty x one hundred fifty centimetre ) with anti skid pattern matt finish in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm( twelve millimetre) thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm ( three . three kilogram / square metre ) including grouting the joint with white cement & matching pigments etc. complete including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying Ceramic glazed floor tiles of size 300x300 mm ( three hundred x three hundred millimetre ) (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm ( twenty millimetre ) thick cement mortar 1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm ( three . three kilogram / square metre ) including pointing the joints with white cement and matching pigment etc., complete including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying Full Body vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm( twenty millimetre ) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete: Size of Tile 600x600 mm ( six hundred x six hundred millimetre ) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying Full Body Vitrified tiles in different sizes (thickness to be specified by manufacturer), with waterabsorption less than 0.08 % and conforming to I.S.15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm ( twelve millimetre ) thick bed of cement mortar 1:3 (one cement: three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete Size of Tile 600x600 mm ( six hundred x six hundred millimetre ) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying full body vitrified floor tiles out of single piece tread 30X150 cm ( thirty x one hundred fifty centimetre) with anti skid pattern (with matt finish)of approved shade of jhonson/kajaria/AGL/RAK or equavalent, (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm ( twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm ( eighteen millimetre ) thick stone slab over 20 mm ( twenty millimetre) (average) thick base of cement mortar 1:4 (one cement : four coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent including carriage of materials with in all leads, lifts and other incidentals.
Providing And fixing glazed Digital tiles 300x600 x 8 mm ( three hundred x six hundred x eight millimetre ) thick of approved Shade and manufacturer in skirting risers of steps and dado 12 mm ( twelve millimetre) thick cement mortar 1:3(one cement :three sand) and jointed with cement slurry as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and Fixing 10mm wall/partitions of Interior Grade High Pressure Laminate 6mm/8mm/10mm ( six /eight / ten millimetre ) thick upto 2.1 cm ( two poin one centimetre) hight with fire resistant chimical resistant,boiling water resistant,envoirnment frendly green DNA with no uria content to be installed with stainless steelfittings,of GREENLAM/MERINO complete as per drawings. specification and direction of the Engineer in Charge including carriage of materials with in all leads, lifts and other incidentals.
ROOFING Providing and fixing 15 cm ( fifteen centimetre ) wide, 45 cm ( forty five centimetre ) overall semi?circular plain G.S. sheet gutter with iron brackets 40x3mm ( forty x three millimetre ) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete :0.80 mm ( zero point eighty millimetre ) thick with zinc coating not less than 275 gm/m² ( two hundred seventy five gram per square metre) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately :6 mm ( six millimetre) thick Cement fiber board as per IS:14862 including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( ten millimetre ) gap for thermal expansion, (i) Single socketed pipes.110 mm ( one hundred ten millimetre ) diameter including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigidmoulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm ( ten millimetre) gap for thermal expansion. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Bend 87.5° 110mm ( one hundred ten millimetre) bend
Shoe 110mm ( one hundred ten millimetre)
Providing and fixing sandwich puff roofing with top skin of 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.
Providing and fixing 0.62 mm ( zero point sixty two millimetre ) thick plain prepainted steel sheet roofing, with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 ( twenty) microns over 5(five) microns primer coating to back coat of polyster of 5(five) microns over 5(five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals.
Providing and fixing prepainted sandwich puff ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.
Providing and fixing valley 90 cm ( ninety centimetre ) overall 0.60mm (zero point sixty millimetre ) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm ( six millimetre ) dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge.
Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( zero point fifty millimetre ) (+0.05 %) total coated thickness, Zinc coating 120 ( one hundred twenty ) grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Flashings/ Aprons.( Upto 600 mm) ( six hundred millimetre ) including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing, supplying and installation of Microcell Polycarbonate 20mm thick (minimum). UV protected panel system which shall be uniform in colour with an integral microcell core. They should be manufactured with vertical standing seam with standing seam height of 10 to 20 mm ( ten to twenty millimetre) at both sides of the panel. Panels shall be fixed on MS/trusses, purlins with continuous structural aluminium double wall I-profile spacer together with snap-on connector. These connectors to interlock the panel shall have to 2-4 tooth grip-lock locking mechanism to ensure maximum uplift capability and shall pass a pull-out load of minimum 4000 N (4kN) when tested as per ISO 6892:1998 and IS 1608:2005. Panel shall be with additional End-Cap/ aluminium U-profile (mill finish) for ends including glass wool 100 mm. ( one hundred millimetre ) including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm ( six hundred x six hundred millimetre ) module which includes providing and fixing 'C' wall angle of size 20x30x20 mm ( twenty x thirty x twenty millimetre ) made of 0.5 mm ( zero point five millimetre ) thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm ( three hundred millimetre ) center to centre, suspending the main C carrier of size 10x38x10 mm ( ten x thirty eight x ten millimetre ) made of G.I steel 0.7 mm( zero point seven millimetre ) thick from the soffit with help of soffit cleat 37x27x25x1.6 mm ( thirty seven x twenty seven x twenty five x one point six millimetre ) rawl plugs of size 38x12 mm( thirty eight x twelve millimetre ) and C carrier suspension clip and main carrier bracket at 1000 mm ( one thousand millimetre ) c/c. Inverted triangle shaped Spring Tee having height of 24 mm ( twenty four millimetre ) and width of 34 mm ( thirty four millimetre ) made of Gl steel 0.45 mm ( zero point forty five millimetre ) thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm ( six hundred millimetre ) centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm ( six hundred x six hundred and zero point five millimetre ) thick with 25 mm ( twenty five millimetre ) height, made of G I sheet having galvanizing of 100 gms/ sqm( one hundred gram per square metre ) (both sides inclusive) and electro statically polyester powder coated of thickness 60( sixty) microns (minimum), including factory painted after bending. including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Acoustic Wood wool Perforated Desigener tiles in combination with calcium sillicate tile Ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm ( one hundred twenty gram per square metre ) (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm ( twenty five millimetre ) wide x 1.6 mm ( one point six millimetre) thick with flanges of 27 mm ( twenty seven millimetre) and 37mm,( thirty seven millimetre) at 1200 mm( one thousand two hundred millimetre ) centre to centre, one flange som fixed to the ceiling with dash fastener 12.5 mm ( twelve point five millimetre )dia x 50mm ( fifty millimetre ) long with Omm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm( twenty five x ten x zero point five millimetre ) of required length with nuts & bolts of required size all complete as per drawings, specification and direction of the Engineer in Chargeincluding carriage of materials within all leads, lifts and other incidentals.
Providing and fixing Wooden perforated accoustical panel over 50mm ( fifty millimetre ) thick absorb wool insulation in combination with stretch fabric aphony Fibrette 600X600 mm( six hundred x six hundred millimetre ) of approved shade tiles false Ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm( twenty five millimetre ) wide x 1.6 mm ( one point six millimetre ) thick with flanges of 27 mm and 37mm, ( twenty seven and thirty seven millimete ) at 1200 ( one thousand two hundred ) min centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm ( twelve point five millimetre ) dia x 50mm( fifty millimetre ) long with 6mm ( six millimetre ) dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm ( twenty five x ten x zero point fifty millimetre ) of required length with nuts & bolts of required size all complete as per drawings. specification and direction of the Engineer in Charge.
Providing and fixing 120X60X12 mm ( one hundred twenty x sixty x twelve millimetre ) thick ply finished with 4mm (four millimetre) vaneer of delux prolad/Himalian with Rai wood borders, laid over absorb wool 50mm ( fifty millimetre ) thick insulation, polished in natural approvd shade false Ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm ( one hundred twenty gram per square metre ) (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm ( twenty five millimetre ) wide x 1.6 mm ( one point six millimetre ) thick with flanges of 27 mm( twenty seven millimetre ) and 37mm( thirty seven millimetre ) at 1200 ( one thousand two hundred ) min centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm ( twelve point five millimetre dia x 50mm ( fifty millimetre ) long with 6mm ( six millimetre ) dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm ( twenty five x ten x zero point fifty millimetre ) of required length with nuts & bolts of required size all complete as per drawings. specification and direction of the Engineer in Charge including carriage of materials within all leads, lifts and other incidentals.
Providing and fixing of Wooden slats of approved shade 2440mm x128mm x 16mm( two thousand four hundred forty x one hundred twenty eight x sixteen millimetre) made MDF backed with acoustical fleece to be installed with 15mm GI and Lock in Clips on the back of tongue and groove system to be installed with 2400x50mm( two thousand four hundred x fifty millimetre ( web flenges 15 and 50mm ( fifteen and fifty millimetre ) fully with backing of 50mm ( fifty millimetre) thick absorb wool/insulation knurled hot depped galavanised steel with 120 GSM Zink coating of Prolad/ Himalayan/ Armstrong. The high grade MDF panels shall be melamine laminate of size 2440mm x128mm x 18mm( two thousand four hundred forty x one hundred twenty eight x eighteen millimetre) with 2mm ( two millimetre) groove at 14mm ( fourteen millimetre) pitch, Tongue and Groove edges for seamless mounting having density of 800kg/m3(base panel confirming to IS 12406 and laminated panel confirming to IS 14587). The back of the panels are perforated with a nonwoven fabric covering of 0.2mm ( zero point two millimetre ) for providing Sound absorption via the acoustic impedance method. Panel is fixed by using GI Framework 2400mm x 50mm x 0.50mm ( two thousand four hundred x fifty x zero point fifty millimetre) spaced at 600mmx600 ( six hundred x six hundred millimetre) c/c & 16 mm ( sixteen millimetre) WPC framework spaced at 400mm ( four hundred millimetre ) centers with suitable brackets and the system is backline with 50 mm ( fifty millimetre) Rockwool insulation@48kg density and along with all accessories or Screw the aluminum extruded profile for channeled woodworks provided by manufacture over the lowest and second wooden batten at an on- center distance of 600mm ( six hundred millimetre) Install the first set of wooden panels by inserting the clips for border channeled woodworks and insert the groove of the panel into the projecting flange of the aluminum clip. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing clips for inside channeled woodworks into the next keel till the actual height is achieved. Use clips for border channeled woodworks to finish off the installation. MAKE: PROLAD/ ECOPHONE/ HERADESIGN including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and Fixing Fabric Acoustical Panels in combination with wood fiber cement composite slats 20mm ( twenty millimetre ) thick with colours of approved shade size 2400x50mm ( two thousand four hundred x fifty millimetre ) web Flenges 15mm( fifteen millimetre ) and 50mm ( fifty millimetre ) fully with backing of 50mm( fifty millimetre ) thick absorb wool/insulation above of Himalayan/ Prolad/Armstrong or its Equivalent. Including required framework complete in all respect. The Grid should be 24 mm(twenty four millimetre ) wide T sections i.e. the Main Runner 3000mm( three thousand millimetre ) in web height of 32 mm( thirty two millimetre ), 1200 mm & 600 mm( one thousand two hundred millimetre & six hundred millimetre ) Cross Tees in web height of 26mm(twenty six millimetre ) to comprise main runner spaced at 1200mm ( one thousand two hundred millimetre ) centers securely fixed to the structural soffit using suspension system at 1200mm( one thousand two hundred millimetre ) maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm ( four hundred fifty millimetre) from the adjacent wall. Flush fitting 1200mm ( one thousand two hundred millimetre ) long cross tees to be interlocked between main runners at 600mm( six hundred millimetre ) centre to form 1200 x 600 mm ( one thousand two hundred x six hundred millimetre) module. Cut cross tees longer than 600mmsix hundred millimetre) require independent support. 600 x 600mm (six hundred x six hundred millimetre)module to be formed by fitting 600mm (six hundred millimetre) long flush fitting cross tees centrally between the 1200 mm ( one thousand two hundred millimetre ) cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, ( three thousand x nineteen x nineteen millimetre ) secured to walls at 450 mm( four hundred fifty millimetre) maximum centers and as per the drawing and the work complete in all respects to the satisfaction of Engineer in-charge. MAKE: ERADESIGN/PROLAD/ECOPHON including carriage of materials within all leads, lifts and other incidentals.
FINISHING 15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/ concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.
15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/ concrete/ stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.
6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Finishing walls with 100% ( one hundred) Premium acrylic emulsion paint having VOC less than 50( fifty) gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additivesNew work (Two or more coats applied @ 1.43( one point forty three) litre/ 10 sqm (ten square metre ) Over and including priming coat of exterior primer applied @ 0.90( zero point ninety ) litre/10 sqm.( ten square metre including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm ( ten square metre ) of approved brand and manufacture including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Applying priming coat With ready mixed pink or Grey primer of approved brand and anufacture on wood work (hard and soft wood) including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming pant brushing red leadred oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.
Providing and applying white cement based putty of average thickness 1 mm,( one millimetre ) of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour:Two coats including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Brass hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.
250mm (Two hundred fifty millimeter)
200mm(Two hundred millimeter)
Providing and laying 60mm( sixty millimitre) thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm ( fifty millimetre ) thick compacted bed of coarse sand, filling the jointswith line sand etc. all complete as per the direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals.
Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm ( three hundred x three hundred x nine point eight millimetre ) having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm( twenty millimetre ) thick base of cement mortar 1:4 (one cement : four coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.
Providing and placing in position 100 mm (one hundred millimetre ) thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm ( eight millimtre ) dia TMT bars of Fe 500 grade @ maximum 100mm ( one hundred millimetre) cement concrete on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm( one point six millimetre ) thick , 100 mm ( one hundred millimetre) wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2(two) Nos. 12 mm ( twelve millimetre) dia bar for hooks etc including cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.
ALUMINIUM WORK Providing and fixing double glazed hermetically sealed glazing in aluminium/steel windows, ventilators and partition etc. with 6 mm ( six millietre) thick clear float glass both side, having 12 mm( twelve millimetre) air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in?charge complete including carriage of materials within all leads, lifts and other incidentals.
NEW TECHNOLOGIES AND MATERIALS Providing and fixing roofing consist of 0.8 mm( zero point eight millimetre ) thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3mm( three millimetre) laid at 100x100 mm ( one hundred x one hundred millimetre ) grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately) including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANNEL : Providing and Fixing Structural Glazing fabricated from Roll formed sections made of Pre-painted Steel / Powder coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 ( one hundred twenty)Gm/Sqm) with total coated thickness of 0.72mm( zero point seventy two millimetre ) . The glass holding section made of 304( three hundred four ) grade stainless steel of 0.58mm ( zero point fifty eight millimetre ) thick. Galvanized steel sections are to be sued as stiffeners inside the colour coated steel/powder coated sections as per the design requirement. Design calculations are made of suit wind pressures as given in IS 875 including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Paint Specifications: Coated sections should be with Primer coat with epoxy primer of 5 – 7 microns thick, finish painted with a polyester paint of 12-16 ( twelve to sixteen) microns thick and back coated with Alkyd backer of 5-7 ( five to seven) microns or powder coated with pure polyester powder up to 50-60 ( fifty to sixty ) microns thick
Dimensions of Sections: The vertical section should be of 50mm x100mm x 0.72mm, 33mm x 58mm x 0.72mm for frame horizontal section, stiffener section should be 48mm x 98mm x 1mm, cover profiles sections should be of 20mm x 58mm x 0.58mm, Glass holding section should be of 37mm x 37mm & 37mm x 18mm.
Fixing Details: Brackets made of CRCA powder coated/Electroplated should be used to connect vertical to horizontal, vertical to slab, to fix verticals at top & bottom as per site requirement. Gasket made of Ethyl Propylene Diamine Monomer. Natural cure, with Good U.V. Resistance Silicon to be used. Wall fixing of sections to concrete/masonry wall should be with self-expanding cap & screws.
Providing, assembling and supplying vision glass panels (IGUS) comprising of hermetically-sealed 6-12- 6 mm( six - twelve- six millimetre) insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, ofapproved colour and shade with reflective soft coating on surface #2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm ( twelve millimetre) wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as sqm directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor."(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No. )"For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant)provided and fixed in position, shall be measured in sqm."(i) Coloured tinted float glass 6mm( six millimetre ) thick substrate with reflective soft coating on face # 2, + 12mm ( twelve millimetre) Airgap + 6mm Heat Strengthened clear Glass of lapproved make having pronerties as visible Light transmittance (VLT) including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and Fixing Top Hung shutters in Structural Glazing fabricated from Roll formed sections made of Pre-painted Steel / Powder coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 ( one hundred twenty) Gm/Sqm) with total coated thickness of 0.72mm ( zero point seventy two millimetre ) . The glass holding section made of 304 grade stainless steel of 0.58mm( zero point fifty eight millimetre) thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel/powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875. Primer coat with epoxy primer of 5-7 microns thick and back coated with Alkyd backer of 5-7 ( five to seven ) microns or powder coated with pure polyester powder up to 50-60 ( fifty to sixty) microns thick. The outer frame should be of 20mm x 58mm x 0.58mm, ( twenty x fifty eight x zero point fifty eight millimetre) Shutter section should be of 58mm x 33mm x 0.72 mm ( fifty eight x thirty three xzero point seventy two millimetre), stiffener section should be 55mm x 31mm x 1mm( fifty five x thirty one x one millimetre) EARL Bihari Hinges – 2 (two)Nos for each shutter and Aluminum Stays – 2 Nos. for each shutter, Aluminum Handle – 1 no. for each shutter including carriage of materials within all leads, lifts and other incidentals as per direction of Engineer - in - charge .
W.S & S.I Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth upto any leads and lifts disposted earth to be leveled and neatly dressed, Pipes, cables etc. exceeding 80 mm( eighty millimetre) dia but not exceeding 300 mm( three hundred millimetre ) dia as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
20mm (Twenty Millimetre) nominal bore
25 mm (Twenty Five Millimetre) nominal bore
Providing and fixing Polyethelene-Aluminium Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, ( eighty degree centigrad) including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00( one metre) spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge including carriage of materials with in all leads, lifts and other incidentals.
Concealed work, including cutting chases and making good the wall etc
1216 (16 mm( sixteen millimetre ) OD pipe
Providing and fixing 25 mm (Twenty Five Millimetre) nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete 25 to 40 mm (Twenty Five to forty Millimetre)nominal bore including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Constructing masonry Chamber 30x30x50 cm( thirty x thirty x fifty centimetre ) inside, in brick work in cement mortar 1:4 (one cement :four coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm ( one hundred x one hundred x seventy five millimetre ) (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (one cement : two coarse sand :four graded stone aggregate 20 mm ( twenty millimetre ) nominal size), including necessary excavation, foundation concrete 1:5:10 ( one cement : five fine sand : ten graded stone aggregate 40mm( forty millimetre ) nominal size ) and inside plastering with cement mortar 1:3 (one cement : three coarse sand) 12mm ( twelve millimetre ) thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 ( seven point five) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing white vitreous china Angel C8915 wall mounting water closet of size 455x355x355 mm ( four hundred fifty five x three hundred fifty five x three hundred fifty five millimetre) of approved shape including seat cover, and cistern fittings, nuts,bolts and gasket etc of Perryware , Cera,Jaquar, Hindware or equivelent complete as per direction Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing white vitreous china CURSE SET WC cat No. S1021114P extended wall mounting water closet of size 780x370x810 mm( seven hundred eighty x three hundred seventyx eight hundrd ten millimetre) of approved shape including providing & fixing white vitreous china cistern Cat No. S1060106 with dual flush fitting, of flushing capacity 3 litre/ 6(six) litre (adjustable to 4(four) litre/ 8 (eight) litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc of Perryware , Cera,Jaquar, Hindware or equivelent complete as per direction Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing viterous China CASCADE NXT C0207 Wall Hung Closet (540x365x395mm ) ( five hundred forty x three hundred sixty five x three hundred ninety five millimetre) White Shade Wall hung WC with soft close seat cover, hinges, accessories set of /Jaquar or equivalent complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Single piece slim concealed cistern with floor mounting frame installation kit and S-type Drain pipe conection set for wall hung WC (without flush control Plate) JCS-WHT-2400FS of Jaquar or equivalent including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Flushing Plate Control palate vignette prime (JCP-CHR-812415) Jaquar or equavalent including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing vitreous China Flat back urinal ASTUTE C 0586 ASTUTE water less Urinal 345 x365x 655mm ( three hundred forty five x three hundred sixty five x six hundred fifty five millimetre) In White Shadeof Perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same and carriage of materials within all leads and lifts :- Of Superior quality as per direction of Engineer-Charge.
Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm( forty millimetre ) C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm( six hundred x four hundred fifty x two hundred millimetre ) including carriage of materials with in all leads, lifts and other incidentals. as per direction of Engineer - in - charge .
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm( forty millimetre) , including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm( five hundred ten x one thousand forty millimetre) bowl depth 250mm ( two hundred fifty) including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing viterous China wash basin C8863 505x405x155mm five hundred five x four hundred five x one hundred fifty five millimetre) Basin (half Pedestal) In White Shade of Perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same and carriage of materials within all leads and lifts :- Of Superior quality as per direction of Engineer-Charge including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing viterous China wash basin CRUSE SET CAT NO S2040101 Wash Basin 510 x 400mm ( five hundred ten x four hundred millimetre ) and pedestal cat no. S2090101 of perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same and carriage of materials within all leads and lifts :- Of Superior quality as per direction of Engineer-Charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing viterous China wash basin CASCADE NXT C0404 Basin With Half Pedastal C0379 In White Shade of Perryware /jaquar/ Hindware/ Cera or equivalent including cutting holes & making good the same and carriage of materials within all leads and lifts :- Of Superior quality as per direction of Engineer-Charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing 600x450 mm ( six hundred x four hundred fifty millimetre ) beveled edge mirror of superior glass (of approved quality) complete with 6 mm ( six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.: 600 mm ( six hundred millietre) long towel rail with total length of 645 mm, ( six hundred forty five millietre) width 78 mm (seventy eight millietre) and effective height of 88 mm, ( eighty eight millietre) weighing not less than 190 ( one hundred ninety) gms. including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing 600x120x5 mm ( six hundred x one hundred twenty x five milimetre ) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm ( forty millimetre ) long screws, rawl plugs etc., complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing toilet paper holder C P Brass as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals..
Providing and fixing PTMT liquid soap container 109 mm( one hundred nine millimetre) wide, 125 mm ( one hundred twenty five millimetre) high and 112 mm ( one hundred twelve millimetre) distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.( one hundred five gram ) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing PTMT soap Dish Holder having length of 138mm ( one hundred thirty eight millimetre) breadth 102mm, height of 75mm ( seventy five millimetre) with concealed fitting arrangements, weighing not less than 106 gms. ( one hundred six gram) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing Division plate for urinals: 600mmx300mm ( six hundred x three hundred millimetre) size of Hindware or equivalent make as per direction of Engingeer-in-charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing 15 mm ( fifteen millimetre) nominal bore C.P. brass bib cock of approved quality conforming to IS:8931 : including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing 15 mm ( fifteen millimetre) nominal bore brass stop cock of approved quality including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing 115 mm ( one hundred fifteen millimetre ) nominal bore, 86 mm ( eighty six millimetre) long, weighing not less than 88( eighty eight) gms PTMT concealed stop cock with flange of Jaguar and approved quality and colour as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing 15 mm ( fifteen millimetre) nominal bore plasticised PVC connection pipe with brass unions including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing C.P. Brass waste, and plug for glazed ware sinks, basins, etc. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug, brass chain and studs 32mm (thirty two millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals..
Providng and fixing gun metal gate valve with C.I. Wheel of approved quality (screwed end) of 25 mm ( twenty five millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.
Providing and fixing 15mm ( fifteen millimetre) nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.(tank of 1000( one thousand) Litres capacity)including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing 110 mm X 90 mm( one hundred ten x nineety millimetre) PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. including carriage of materials with in all leads, lifts and other incidentals. as per direction of Engineer - in - charge .
Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals
110 mm dia (one hundred ten millimetre ) dia
150 mm dia(one hundred fifty millimetre ) dia
Providing and fixing 15 mm( fifteen millimetre) nominal bore brass ferrule with C.I. mouth coverincluding boring and tapping the main as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .
Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete / including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .
Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC door bend with oval access door insertion rubber washer 3 mm Three millimetre) thick bolts and nuts ISI market complete including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals
Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC Collar ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals
Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals
Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals
Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC ‘P’ or ‘S’ trap for water closet (squatting pan ) ISI marked including jointing the trap with pan and PVC pipe with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals
Providing and fixing 8 mm( eight millimetre) dia C.P. / S.S. Jet with flexible tube upto any metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .
Providing and fixing U- Shaped wall mounted rail with hinges 600 x 100mm( six hundred x one hundred millimetre) Cat No. B2210107 and Wall Mounted Grab Bar 600mm ( six hundred millimetre ) Long CAT No. B2210106 jaquar or equivalent Superior quality as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (one cement : two fine sand) including testing of joints etc. complete :150 mm( one hundred fifty millimetre) dia. R.C.C. pipe including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and laying cement concrete 1:5:10 (one cement : five coarse sand : ten graded stone aggregate 40 mm ( forty millimetre ) nominal size) all-round S.W. pipes including bed concrete as per standard design :150 mm( one hundred fifty millimetre ) diameter S.W. pipe including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg ( four point fifty kilograme) and frame to be not less than 2.70 kg ( two point seven kilograme) as per standard design including carriage of materials with in all leads, lifts and other incidentals .
Constructing brick masonry circular type manhole 0.91 m ( zero point ninety one metre) internal dia at bottom and 0.56m( zero point fifty six metre) dia at top in cement mortar 1:4 (one cement : four coarse sand), inside cement plaster 12 mm( twelve millimetre thick with cement mortar 1:3 (one cement : three coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (one cement : three coarse sand : six graded stone aggregate 40 mm( forty millimetre) nominal size), and making necessary channel in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm( twenty millimetre) nominal size) finished with a floating coat of neat cement, all complete as per standard design :
0.91 m ( zero point ninety one metre) deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm( five hundred sixty millimetre) internal diameter con- forming to I.S. 12592, total weight of cover and frame to be not less than 182 kg .( one hundred eighty two kilogram ) fixed in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm ( twenty millimetre) nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm ( twelve millimetre) thick cement plaster at the external surface shall be paid for separately) as per direction of Engineer - in - charge .
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete 25 to 40 mm ( twenty five to forty millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer - in - charge .
Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately) including carriage of materials with in all leads, lifts and other incidentals .
Supplying and fixing C.I. cover without frame for manholes 455x610 mm ( four hundred fifty five x six hundred ten millimetre) rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg ( twenty three kilograme) including carriage of materials within all leads, lifts and other incidentals.
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm ( five centimetre to twenty centimetre) in recharge pit, in the required thickness, including carriage of materials within all leads, lifts and other incidentals.
S G Constructions
unipro
NARESH KUMAR TULI
Suket Construction Co. Pvt. Ltd.
KDN Infrastructure Pvt. Ltd.
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid