NEW FURNITURE OF PROVN OF OTM ACCN FOR DIV ENGR REGT (PHASE ONE OF TWO PHASES ) AT AHMEDABAD CANTT UNDER GE (A) AHMEDABAD

BATH MAT PVC (FD/E6/MAP/07) The Bath Mat PVC shall be made up of 5mm thick PPCP material .The size of the bath mat shall be 400mm Lx300mm Wx250mmH.The bath mat shall have centre leg of dia 25mm.The four legs shall be in arc shape and of size 10mmx100mm.The top of the bath mat shall have 3mmx10mm thick stiffener moulded along with the seat in single piece underneath. The weight of the bath mat shall not be less than 1.3 kgs. Make-AMKO or Cello.

BOOK CASE OPEN LARGE GLAZED (FD-356) Overall size shall be 960X760X350 mm First Class Teak Wood free from knots and cracks shall be used with moisture content permissible as per ISI 287-1973 All Wood Work and teak veneered surface shall be malamine polished except where paniting is indicated in drg. 19 mm thick Prelaminated MDF board to be used as per drg. The other side of MDF Should be painted witha coat of oil paint over a coat of primer as a balancing coat.

CHAIR DINING (FD-279) Overall size shall be 440mm long, 440mm wide and 890mm high. Front legs shall be of teak wood and 35mmx55mm in section and 460mm high. Rear legs shall be of teak wood 35mmx55mm in section and 890mm high. Front legs shall be joined withrear legs by teak wood seat frame which shall be of 30mmx55mm in section and made to shape as shown on drawing. 20mmx200 teak wood stiffeners shall be provided on sides joining front and rear legs at 100mm from bottom of seat frame. Two back rails of teak wood 20mmx45mm in section made to shape out of 30mmx45mm teak wood shall be profided between the rear legs as back rest. Front and side rails of seat shall be of 30mmx55mm. Came sja;; be pf {re,oer spr Sjaj bramd. Cane shall be 2mm wide and 0.4mm thick half round gola type weighing not less than 6gms per ten running meter. Caning shall be done in Godgrej pattern. 25mm dia and 25mm high PVC shoes shall be provided to bottom of all legs. All wood surfaces exposed to view when placed in position shall be malamine polished

CHAIR DRAFTSMAN (FD-204) DIMENSION:-Overall size shall be 470mm wide ,445mm deep and 1040mm high. DESCRIPTION:-Timber shall be seasoned teak wood Ist Quality.Front legs shall be 50x50mm at top and 40x40mm at bottom .Rear legs shall be 95x50mm .The seat of the chair shall be woven in godrej pattern with 2mm wide o.25mm thick best quality cane. . All Diamensions, shape and size shall be followed as per drg. All joints, fixing shallbe done in accordance with standard specifications. Rest all as shown on drg. FINISH:-All wooden expose surfaces shall be malamine polished two coats after preparation of surfaces

CHAIR EASY (FD-229) DIMENSION: Overall size shall be 510 mm long, 575mm wide and 720mm high . DESCRIPTION:- All wood shall be first class teak (MP). Front legs shall be 30mmx55mm in section and 355mm high up to seat level. Rear legs shall be of 30mmx55mm in section and 300mm high up to seat level and slanting 50mm away from vertical. Front, back and side rails of seat shall be out of 30mmx55mm in section and made to shape as shown on drawing. front, back and side rails shall join the front and rear legs at 355mm high and 300mm high in rear Teak wood arm rests shall be provided at 150mm above seat level and shall be of 30mmx55mm in section as shown on drawing. Back rest shall be made of frame consisting of top horizontal rail of 30mmx100mm in section out of 60mmx100mm teak wood made to shape as shown on drawing and lower horizontal rail of back rest shall be of 30mmx100mm in section joined together by vertical side rails of 30mmx25mm in section teak wood to form the frame |Caning shall be done with plastic cane of 2mm wide and 0.4mm thick half round gola type weighing not less than 6gms in ten running meters. Caning shall be done in Godrej pattern. PVC shoes 25mmx25mm shall be provided at the bottom of all legs. FINISH:- All wood surfaces exposed to view when placed in position shall be given high gloss Malamine polish with lacquer finish.

CHAIR EASY WITH CUSHION (FD-358) DIMENSION:Overall size shall be 510mm long, 545mm wide and 710mm high. DESCRIPTION:Timber shall be seasoned teak wood(MP) Ist Quality. Front legs shall be of size 70mmx25mm in section 520 mm high and rear legs shall be of section 70 mm x25 mm in section slanting 185 mm horizontally in the height of 490 mm . The front and rear rails shall be provided below the seat joining front legs and rear legs .Front legs shall be 510 mm apart and rear legs shall be 480 mm apart . The top of front legs shall have wooden arms rest of 65 mm x25 mm in section and 610 mm madfe to shape as shown on drg. The legs shall be joined by side rails 70 mm x 25 mm in section teak wood. The bottom frame of seat shall be of 55 mm x 20 mm in section over which 3/4 mm thick plywood commercial shall be fixed. 75 mm thick foam cushion of 32 density with upholster with leathersied rexine of approved shade and texture as directed by BSO/ GE.Hard rubber/ PVC shoes of 25 mm dia 25 mm high shall be provided to the bottom of legs with screws FINISH:All wooden surfaces shall be polished with two coats of melamine polish with spray machine after preparation of surfaces.

CHAIR FOR TABLE CARD (FD-353) Overall size shall be 440mm long, 430mm wide and 890mm high. All wood shall be of first class hard wood teak(mp). Front legs shall be of 30mmx55mm in section form bottom to top of legs and 460mm high up to seat level. Rear two legs shall be of 30mmx55mm in section form bottom to top of legs and top rounded as shown on drawing. The legs at seat level shall be joined together with 30mmx65mm in section front, sides and rear rails made to shape as shown on drawing. The rails shall inserted in the groove of legs by 15mm. Two sides stiffeners 25mmx20mm in section shall be provided at 100mm high from bottom of legs joining front and rear legs in the sides. oNe stiffener of 25mmx20mm section shall be provided in the middle of short stiffeners joining shhort stiffeners. Two horizontal back rests 45mmx15mm in section, one at 25mm from top of legs and other at 45mm from botom of the top horizontal rails shall be provided out of 45mmx35mm wood made slightly in curved shape. Caning shall be done with 2mm wide and 0.4mm thick cane of shah or premier brand cane weighing not less than 6gms per ten running metre. The weaving shall be done Godrej pattern. Hard rubber/PVC rings 25mm dia and 25mm high shall be screwed to the bottom of all legs. All wood surfaces exposed to view when placed in position shall be Malamine polished with high gloss finish.

FORME WITH BACK (FD-78) DIMENSION:Over all size shall be of 1800X510X900MM. DESCRIPTION:wooden seat shall be of teak wood in one piece and of size 1800mm long 255mm wide and 25 mm thick bolted to frame with 3 mm dia GI nut bolt and washers.Steel frame shall be 1500mm long in such a way that teak wood seat shall project 150mm from frame on each side .Back rest shall be of teak wood and 1800mm long,150mm wide and 19mm thick .The back rest shall be 1800mm long the width is 300mm at bottom and 255 mm at top of wooden plank.Legs shall be 25mm MS tube of wall thickness 1.6mm. Steel frame shall be provided with 25mm square MS tube 16 gauge .All Dimensions, shape and size shall be followed as per drg. FINISH: All wooden expose surfaces shall be Malamine polished two coats after preparation of surfaces and steel portion shall be painted with synthetic enamel black paint

HAT STAND (FD-233) Hat Stand (Small):- Overall size shall be 1000mm long and 710mm high. All wood shall be of teak wood (mp). Top and bottom horizontal rails and two vertical sides shall form the frame of 50mmx20mm in section for the Hat stand. The top and bottom horizontal rails shall be joined by intermediate vertical stiffeners of 50mmx20mm in section at 288mm from inside of right hand side of vertical frame. On the left hand side of Hat Stand, two horizontal stiffeners, 50mmx20mm in section shall be provided. The top stiffener shall be at 160mm from bottom of top horizontal frame to the center of the top stffener. The bottom stiffener shall be at 200mm from bottom of horizontal frame to the center of bottom stiffener. On right hand side of Hat Stand. one horizontal stiffener. 50mmx20mm in section shall be provide. The Frame of Hat Stand shall be provided with 4mm thick teak ply (one side teak face). The back of Hat Stand shall provided with 4mm thick commercial plywood. A mirror of 440mm high and 300mm wide with 5.5mm thickness of Atul, Modiguard or Golden fish, free from all distorition and defects shall be provided on right hand side of Hat Stand with 10mmx12mm in section teak wood beads al-around the mirrorl Teak ply 4mm thick shall not be provided at places coveed by 5.5mm thick mirror irrespective of what is shown on drawing, four brass pegs of 75mm wide and 120mm high of shape as approved by Engineer-in-charge. 35mm wide and 6mm thick teak wood edging shall be provided al-round the Hat Stand. Two key plates of mild steel sheet 3mm thick flat iron with key holes as shown on drawing shall be provided to two top corners at the back of Hat Stand as directed by Engineer-in-charge. All wood and teak ply surfaces exposed to view when placed in position shall be Malamine polished with high gloss fininsh. All steel surfaces shall be painted with two coats of black paint over a coat of primer after preparation of surfaces Brass pegs shall have shining surfaces and remain untreated irrespective of what is shown on drawing.