S&T work in Connection with -"Proposed New Block Station along with development of Goods Shed at Manklav Station."

Design, Manufacture & Supply of Electronic Interlocking (EI) System (with centralized arrangement) for 4 (FOUR) Line stations as per Signal Interlocking Plan in 'Hot Standby architecture'. EI system shall be provided to operate with dual VDU Control Terminal as per RDSO Specification No.RDSO/SPN/ 192/2019 Ver. 2 or latest and from RDSO approved source only. It mainly consist of Microprocessor Equipments, Interface Equipments, EI vendor specific Interfacing Relays , In-built event Logger, In-built Power Supply Equipments, Racks (Only Relay Rack/EI Rack), Indoor cables, Wires, Fuses , Fixtures, Mounting arrangements along with all accessories required to make complete EI system functional. Design of indoor EI system should be compatible as per outdoor interlocking requirement based on Signal Interlocking Plan & Selection Table of station/yard. This 1 item also includes supply of following :- (a) Supply of documents/manuals for EI system as per RDSO Specn.No. RDSO/SPN/192/2019 Ver. 2 or latest. (b) Supply & provision of protective devices like surge and lightning protection devices compatible to RE standards as recommended by OEM / RDSO. Note: It includes supply of all the material which is required to make complete EI system to be functional and as recommended by RDSO in Specn.No.RDSO/SPN/192/2019 Ver. 2 or latest. Design , manufacture & Suupply of EI system will be done by OEM after following all the guidelines/directives issued by RDSO from time to time.The Technical Requirements are attached with the tender document. Railway will supply RDSO approved type of relays with approved contact configuration only . In case of requirement of vendor specific relays/relays with non-RDSO approved contact configuration being supplied, the same shall be supplied by the tenderer and cost of required relays shall be included in the cost of EI (Electronic Interlocking) system and number & type of such relays shall be indicated separately. Inspection: RDSO Inspection charges: Borne by Railways Payment terms:100% after supply

Installation, wiring, testing and commissioning of EI System with 'Hot Standby' 2 architecture as supplied upto 6 (six) line station. It includes transportation of material from consignee's depot to the site, erection and grouting of EI Relay Racks, fixing and wiring of all the interfacing relays (Vital & Non-Vital), installation and wiring of Microprocessor equipments, interface equipments, power supply equipments and all other associated accessories to make complete EI system to be functional. Note: (i) Technical Requirements are attached with tender document (ii) Contractor has to arrange simulator/simulation testing panel for testing and commissioning by Selection Table and Square Sheet for each Signalling function.(iii) Installation, wiring, testing and commissioning of EI system will be done by OEM after following all the guidelines/directives issued by RDSO from time to time. Inspection: Consignee Inspection charges: None Payment terms: 100% after commissioning

Supply of work station note book as per Technical Specifications . It also includes 3 supply of Laser Printer (Only branded). The workstation should be capable of reconfiguring the system in case of any alteration in yard interlocking in future. Technical Specifications should be attached with the tender document by Tendering authority. Inspection: Consignee Inspection charges: None Payment terms: 100% after supply

Supply of Instruments and Tool Kits required for Trouble Shooting and repair of hardware and software for EI system should be supplied for stations . (This includes tools required for EI maintenance sorts of crimping, insertion, removal, general purpose tools like screw drivers, spanners, PCB extractor, temp. controlled soldering iron, wire cutter, nose pliers etc. & measuring instruments with carrying case/ holders/ cabinet for technicians/ J.E. for testing, Maintenance and repair at site). Each set comprises of the following :- * Crimping tool for all types of special cable 4 assembly used in EI system. * Insertion tool for all types of special cable assembly used in EI system. *Removal tool for all types of special cable assembly used in EI system. * Digital multimeter (Fluke 111 or better) * Steel cabinet/ Almira, Size: 1980mm height, 915 mm width and 485 mm depth (Godrej Make/Jalaram) of good quality to store tool, spare cards and documents. * Steel Book rack Size: 1850mm height, 900 mm width and 316 mm depth for keeping documents. (Godrej Make/Jalaram) * Clamp Earth Tester.(as per specs mentioned in tender document.) * Clamp Current Meter (fluke 362 or superior) Inspection: Consignee Inspection charges: None Payment terms: 100% after supply

Training of Technician/ Jr. Engineer for installation, Commissioning, Testing, Repairs & Troubleshooting of EI system. (Hard copies of training material/ course modules to be given to each participant). Inspection: Consignee Inspection charges: None Payment terms: 100% after execution

Design, preparation & supply of drawings in computer print copies and original tracing in AUTO CAD FORMAT for Electronic Interlocking at each station. After completion of the 6 work, the completion drawings incorporating completion details are to be supplied as per Technical Specifications given in tender document (upto 6 Line). The techinical specifications are as per ANNEXURE 1.13 of SOR. Inspection: Consignee Inspection charges: None Payment terms: 100% after execution

Training of Officers for installation, Commissioning, Testing, Repairs & Troubleshooting of EI system.(Hard copies of training material/ course modules to be given to each participant). Inspection: Consignee Inspection charges: None Payment terms: 100% after execution

Supply of embedded fanless PC based VDU control terminal as per RDSO spec. No. 8 RDSO/SPN/192/2019 Ver. 2 or latest & RDSO TAN No. - STS/E/TAN/3007 version 1 dated:02.11.12 . The size of VDU shall be minimum 42 inch. Note: (i) Technical requirements shall be mentioned in the tender document. (ii) One revolving chair should be supplied with control terminal. Inspection: RDSO Inspection charges: Borne by Railways Payment terms:100% after supply.

Installation, wiring, testing and commissioning of embedded fanless PC based VDU 9 control terminal as per RDSO spec. No. RDSO/SPN/192/2019 Ver. 2 or latest & RDSO TAN No. - STS/E/TAN/3007 version 1 dated:02.11.12 . Note: (i) Technical requirements shall be mentioned in the tender document by tendering authority. Inspection: Consignee Inspection charges: None Payment terms:100% after commissioning.

Supply of embedded fanless PC based Maintenance terminal as per RDSO spec. No. RDSO/SPN/192/2019 Ver. 2 or latest & RDSO TAN No. - STS/E/TAN/3007 version 1 dated:02.11.12 . 10 The size of VDU shall be minimum 42 inch. Note: (i) Technical requirements shall be mentioned in the tender document by tendering authority. (ii) One table of suitable size alongwith revolving chair should be supplied with Maintenance terminal. Inspection: RDSO Inspection charges: Borne by Railways Payment terms:100% after supply

Installation, wiring, testing and commissioning of embedded fanless PC based 11 Maintenance terminal as per RDSO spec. No. RDSO/SPN/192/2019 Ver. 2 or latest & RDSO TAN No. - STS/E/TAN/3007 version 1 dated:02.11.12 . Note: (i) Technical requirements shall be mentioned in the tender document. Inspection: Consignee Inspection charges: None Payment terms:100% after commissioning.

Preparation of SWR literature in english alongwith associated mid-section interlocked gate with all corrections as per approved SWRD & approved SIP. For this all technical corrections, 12 editing, grammatical correction etc. are to be carried out and one rough print to be given to railways for approval before printing, as required for final processing of CRS sanction. This also includes preparation of maintenance cards in format provided by Rly. Inspection: Consignee Inspection charges: None Payment terms:100% after execution.

Translation of Station Working Rules from english to hindi and framing out in DIGLOT 13 form (or similar software )as per extant Rly practice. The required SWR in english will be provided by the contractor and has been covered separately in item no. 1.21 of Chapter 1 of this SOR. Inspection: Consignee Inspection charges: None Payment terms:100% after execution.

Making photocopies & binding of the SWR literature in English/hindi/Diglot form as per Railway practice. Inspection: Consignee Inspection charges: None Payment terms:100% after execution.

Supply of maintainer's furniture of godrej make or superior and each set consist of(i) 15 executive revolving bearing series low back-floating chair with normal arms cushioned chair-01 Nos. (ii) Executive table size 1650x900x728 mm with 3 drawers one side locker- 01 no .(iii) visitor chair seat & back cushion with high density foam with plastic pvc handle capsule type painted back-03 nos. Inspection: Consignee Inspection charges: None Payment terms:100% after supply.

Preparation and supply of laminated one set of all the completion plans including circuit diagrams and indoor as well as outdoor completion documents on standard 75-micron polyester film for station in Auto CAD. 6 (Six) sets xerox copies will also be provided for each of the 16 documents mentioned below: Cable Route Plan, Cable Core Chart, Location details plan for all the locations, Cable termination details, Signalling Plan, SWR Diagram, Wiring Diagrams, Selection table, Locking table, Contact analysis, Fuse and Tag Block analysis of Relay Rack, CT rack, Control cum Indication Panel/VDU Diagram, Power Panel Diagram, Track circuit plan, rack erection plan and Junction Box details etc. Inspection: Consignee Inspection charges: None Payment terms:100% after execution.

Addition/alteration in existing relay room wiring. It includes supply of PVC insulated indoor Railway signalling cable @ 40<45@Core/40-Core) of (1/0.6) sqmm as per RDSO Spec.No.IRS/S-76/89 (Amnd.2 or latest) for wiring between relay room and SM's/Panel room & Relay room to DP in SM office for block working. This also includes supply of PVC insulated jumper wires of multi strand 16/.2 mm, tinned in all colours as per RDSO Specn.No.IRS-S-76/89(Amnd.2 or latest). 17 This item will include bringing all the power supplies from power room to respective bus bars on relay racks by using 10/6 sqmm copper flexible wire as per instructions of engineer incharge. This will include wiring between control panel and relay room if required. All wiring will be done as per standard practice of North Western Railway with neat dressing & threading. The item includes supply & wiring of tag block, fuse with bases(G-Type and ND Type) and all other related material required for complete indoor wiring in relay room. Inspection: Consignee Inspection charges: None Payment terms:100% after commissioning.

Supply of Micro Processor based Data Logger System with 1280 digital and 32 analog inputs as per RDSO Spec. No. IRS (S) 99/2006 or latest with laser printer 22 ppm (Only branded HP/Brother/Canon). It includes supply of all the items required for complete indoor relay room wiring from data logger to relay rack tag blocks, drawing/extension of power supply upto Data Logger. It includes relay room door lock checking arrangement, commercial power supply monitoring 18 arrangement & monitoring of DG sets, ELD , IPS, UFSBI, BI ,interlinking and networking of Data logger. It also includes supply of leased line MODEM , suitable online UPS (minmum 6 hours backup) and other interfacing cards, if required for networking of Data Logger.This also includes supply of one no. composite computer and printer table (Godrej work station table or similar) for keeping processor module and one number Godrej operator chair Model PCH7001 or similar. Note: Total numbers of relays and other signalling functions/gears required to be wired as per list circulated vide RDSO Letter No.STS/E/Data logger dtd.12.09.2011 or latest guidelines. Inspection: RDSO Inspection charges: Borne by Railways Payment terms:100% after supply

Installation, wiring, testing & commissioning of Micro Processor based Data Logger System with 1280/ 4096 digital and 32 analog inputs as per RDSO Spec. No. IRS (S) 99/2006 or latest It cover complete indoor relay room wiring from data logger to relay rack tag blocks, drawing/extension of power supply upto Data Logger. It includes relay room door lock checking arrangement, commercial power supply monitoring arrangement & DG sets,ELD , IPS,UFSBI, BI interlinking and networking of Data logger. All material required for wiring, networking, power supply monitoring, door-locking arrangement etc will be supplied by contractor.. Note: Total numbers of relays and other signalling functions/gears required to be wired as per list circulated vide RDSO Letter No.STS/E/Data logger dtd.12.09.2011 or latest guidelines. Networking of data logger includes extraction of data report from test room. For networking, required communication channel(Quad/ OFC cable) will be arranged/provided by Rly in SM/ASM's room or in OFC Porta Cabin and it will be extended by contractor upto location of data logger by using CAT-5/6 telecom cable with proper casing and capping. The contractor will supply all the material like CAT-5/6 telecom cable, casing & capping, nuts, bolts etc. The final commissioning will be done after filling up of Pre- Commissioning checklist (circulated by RDSO) with the OEM representative. Inspection: Consignee, Inspection charges: None Payment terms:100% after commissioning

Supply of Failure Analysis System (FAS) as per Technical Specifications. The specification of FAS should be got approved from the Engineer in charge before supply. Note: The 20 Specification of FAS shall be as per technical specification given in contract Agreement or higher version as approved by Engineer In-Charge.(Technical specification shall be provided in tender documents.) Inspection: Consignee Inspection charges: Borne by Railways Payment terms:100% after supply

Installation, testing and commissioning of Failure Analysis System (FAS) as per Technical Specifications. The specification of FAS should be got approved from the Engineer in 21 charge before supply. Note: The Specification of FAS shall be as per technical specification given in contract Agreement or higher version as approved by Engineer In-Charge.(Technical specification shall be provided in tender documents.) Inspection: Consignee, Inspection charges: None Payment terms:100% after commissioning

Supply of 750 VA Off line UPS with battery backup 3 Hours for Failure Analysis System of reputed make of Emerson/APC or superior as per Engineer in-charge. Inspection: Consignee, Inspection charges: None Payment terms:100 % after supply.

Supply of Relay fail safe electronic time delay device with fixed timing (0 -120) 23 seconds and conforming to RDSO Specn.No.IRS:S-61/2000 with Amnd.1 or latest mounted on Q- series relay base & covered complete with connectors, retaining clip etc.The interlocking code for this unit shall be ""AFGKY"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Q-Series Neutral Line Relay (QN1 Type ), 12F/4B, 24V DC complete with 24 plug board(base plate), connectors and retaining clips etc and conforming to BRS- 930 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be ""ABCDE"". Inspection authority:- RDSO Inspection charges:- Bornee by Railways Payment Terms:- 100% after supply.

Supply of Q-Series Neutral Line Relay (QN1 Type ), 8F/8B, 24V DC complete with plug 25 board(base plate), connectors and retaining clips etc and conforming to BRS- 930 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be ""ABCDF"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Q-Series Twin Neutral Line Relay(QNN1 Type), 6F/2B, 24V DC complete 26 with plug board(base plate), connectors and retaining clips etc and conforming to BRS-960 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be ""ACDEK"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Q-Series Twin Neutral Line Relay(QNN1 Type), 4F/4B, 24V DC complete 27 with plug board(base plate), connectors and retaining clips etc and conforming to BRS-960 and RDSO Specn.No.IRS:S-34 & S-23 or latest. The interlocking code for this unit shall be ""ACEHJ"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Q-Series Magnetically Latched Neutral Line Relay (QL1 Type), 11F/4B,24V D C complete with plug board(base plate), connectors and retaining clips and conforming to BRS- 935A and RDSO Specn.No.IRS:S-34 & S-23 or latest.The interlocking code for this unit shall be ""ABDEG"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Q-Series LED ECR (Universal Type i.e.QECX-61), 4F/4B complete with plug 29 board(base plate), connectors, retaining clips etc and conforming to BRS:941A STS/E/RELAYS/AC LIT LED SIGNAL/09-2002 ,Amdt.-1and RDSO Specn.No.IRS:S-34 & S-23 or latest.The interlocking code for this unit shall be ""ABDHK"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Sealing wire used for sealing of signaling relays & equipments. Inspection authority:- Consignee Inspection charges:-None Payment Terms:- 100% after supply.

Supply of DC neutral line relay QNA1K , AC immune, DC neutral line 24V, 6F/6B 31 contacts, complete with plug board, retaining clip and connectors. Conforming to BRS:931A & RDSO letter no STs/E/Relays/UEA/PI dated 30.05.97Annexure II and IRS:S34 & IRS:S23 or latest.The interlocking code for this unit shall be ""CDEKY"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Q-Series Line Relay (QNA1 Type),AC immunized, 8F/8B, 24 V DC along with 32 plug board (base plate), connectors, retaining clips etc and conforming to BRS-931A and RDSO Specn.No.IRS:S@ 45"44@ S-23 and S-60 or latest. The interlocking code for this unit shall be ""ABDGH"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Q-Series Track Relay (QTA2 Type), AC immunized, 9 Ohms, 2F/1B along 33 with plug board (base plate), connectors, retaining clips etc and conforming to BRS:939A & 966(Appendix F2) or latest.The interlocking code for this unit shall be ""FGHKX"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Q-Series Neutral Line Relay(QSPA1 Type), 24V DC,8F/4B along with plug 34 board (base plate), connectors, retaining clips etc and conforming to BRS-933A and RDSO Specn.No.IRS:S@ 45"44@ S-23 & S 60 or latest.The interlocking code for this unit shall be ""ABDEJ"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of Key Lock Checking Relay (KLCR) working on 24V DC, AC Immunized with 35 different ward combinations and contact configuration 4F/4B with 2 extra ward plates and with case, RDSO spec no. RDSO/SPN/219/2016 ver 1.0 or latest, confirming to IRS S-23, S-34 & S@ 45<44@ IRS S:46. Inspection authority:- For bare relay -RDSO, for key lock housing- consignee Inspection charges:-Bornee by Railways Payment Terms:- 100% after supply.

Supply of Point Contactor relay AC immune, plug in type, style QBCA1 DC biased 36 contractor, (QBCA1 Type), 24 V DC, 2F(HD)2F-4B contacts , heavy duty metal to carbon front contacts and back contacts metal to carbon, complete with plug board, retaining clip & connectors, conforming to BRS- 943 and IRS:S-34 & S-23 or latest. The interlocking code ""DEHJX"". Inspection authority:- RDSO Inspection charges:- Borne by Railways Payment Terms:- 100% after supply.

Supply of PVC insulated multi strand, single core copper conductor of size 16/0.2 mm (0.5sqmm) as per IS 694:2010 and RDSO Specn.No.IRS:S-76/89 (Amnd-3) or latest. Each coil should 37 b e of 100/200/500 meters length. Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of 1 x 6 Sqmm (Red/Black/Green) multi strand copper power wire as per IS:694:2010 or latest, 84 conductor each dia 0.30 +/- 0.01 with insulation thickness of 0.8 mm and nominal conductor resistance of 3.3 ohms/km and test parameters as per RDSO Specn.No.IRS:S- 38 76/89(Amnd.3) or latest.Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways(ii) None Payment Terms: 100% on Supply

Supply of 1 x 16 Sqmm (Red/Black/Green) multi strand copper power wire as per IS:694:2010 or latest, 127 conductor each dia 0.40 +/- 0.01 with insulation thickness of 1.0 mm and nominal conductor resistance of 1.21 ohms/km and test parameters as per RDSO Specn.No.IRS:S- 39 76/89(Amnd.3) or latest.Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways(ii) None Payment Terms: 100% on Supply

Supply of 1 x 35 Sqmm (Red/Black/Green) multi strand copper power wire as per IS:694:2010 or latest, 277 conductor each dia 0.40 +/- 0.01 with insulation thickness of 1.2 mm and nominal conductor resistance of 0.554 ohms/km and test parameters as per RDSO Specn.No.IRS:S- 40 76/89(Amnd.3) or latest. Colour of the wire which is required will be specified by the Engineer incharge. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of wiring material in relay room for potential free relay contacts for digital & analog Inputs (1280 digital inputs and 32 analog inputs). It includes supply of PVC insulated indoor Railway Signalling cable (1/0.6 sqmm dia), 60-Core/40-Core/Single Core as per RDSO Specn.No.IRS:S-76/89(Amnd.3) or latest, PVC insulated jumper wires multi strand, tinned in all colours as per RDSO Specn.No. IRS: S-76/89 (Amnd.3) or latest. The item also includes supply & wiring of Modular disconnect terminals /Tag Blocks as per RDSO Specn.No.IRS:S-77/2006 (Rev.1) or 41 latest and RDSO Drg.No.SA-24751 or latest. The wiring for getting potential free contacts of relays for complete PI/RRI/EI installation including points, tracks, signals, panel, power supply, IPS, SSDAC,TLBI,LC Gates, crank handle control etc will be done by contractor. All material will be supplied by contractor except the relays. The Relays will be supplied by Railway. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Installation & commissioning

Supply of Cable Termination(CT) racks as per Drg.No.CSTE/NWR/ SOR/02 complete along with fitting arrangements and also with arrangement for fixing four 8-way terminal strips/ 42 Screw less terminals/ ARA terminals on each row having 16 such rows. Supply of 8 way terminal strips/ Screw less terminals / ARA terminals not covered under this item. Cable termination rack shall be Powder Coated. Inspection: (i) RITES if value of item in work more than 5 lakhs (ii) Consignee if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Installation of Cable Termination Racks Assembly complete including wall supports, 43 scaffolding and suitable grouting arrangements with installation of 8 way/ARA terminals /Screw less connectors, Tag blocks & other necessary accessories etc. The work shall be done as per approved plan, extant practice on N W R & the instruction of Rly engineer at site. Inspection: Consignee Inspection Charges: None Payment Terms: 100% on commissioning.

Supply of ARA Terminal Block (M-6) made of PBT/Poly Carbonate as per RDSO Specn.No.IRS:S-75/2006 (Rev.2) or latest and RDSO Drg.No. SA-23741A(Alt. 4) or latest. Inspection: RDSO. Inspection Charges: Borne by Railways. Payment Terms: 100% on supply.

Supply of Cartridge Fuse Block made of PBT and as per RDSO Drg. No. SA-23748 (Alt. 4) or latest and RDSO Specn.No.IRS:S-75/2006 (Rev.2) or latest. Inspection: RDSO. Inspection Charges: Borne by Railways. Payment Terms: 100% on supply.

Supply of indicating type fuse inserts with holder (material will be supplied only from approved vendors of RDSO). Inspection: Consignee Inspection Charges: Borne by Railways. Payment Terms: 100% on supply. 0.6 A

Supply of indicating type fuse inserts with holder (material will be supplied only from approved vendors of RDSO). Inspection: Consignee Inspection Charges: Borne by Railways. Payment Terms: 100% on supply. 1.6 A

Supply of indicating type fuse inserts without holder (material will be supplied only from approved vendors of RDSO). Inspection: Consignee Inspection Charges: Borne by Railways. Payment Terms: 100% on supply. 0.6 A

Supply of indicating type fuse inserts without holder (material will be supplied only from approved vendors of RDSO). Inspection: Consignee Inspection Charges: Borne by Railways. Payment Terms: 100% on supply. 1.6 A

Supply of round head type non-deteriorating type low voltage cartridge fuse as per 50 RDSO Specn.No.IRS:S-78/92 or latest and Capacity - 2/4/6/10A/16A/20A Amp. (material will be supplied only from approved vendors of RDSO). Inspection: Consignee Inspection Charges: Borne by Railways. Payment Terms: 100% on supply.

Supply of PVC insulated Railway Signaling multi-core Indoor Cable 60core (0.6mm 51 dia) conforming to IRS:76/89(Amd3) or latest. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply Per

Termination of Outdoor Cables (Main Cables /tail cables) at both ends in location 52 boxes, cable termination rack in relay room, station building, generator room etc. The item includes dressing of cables and wires with dressing threads as per standard practice. All material required for this item will be supplied by contractor. The outdoor cable shall be terminated in Relay Room, DG Room, ASM Room etc under supervision and instructions issued by Engg. incharge of the work. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution

Supply of Disconnect Terminal Block, Screw less type, as per RDSO Spec. No. RDSO/SPN/189/2004(Modular Terminal Blocks, Fuse Terminal Blocks &Miniature fuse link of international standard for Railway signaling) With latest amendments. Inspection: (i) RDSO/RITES if 53 value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply Supply of Disconnect Terminal Block, Screw less type, 4-wire front entry (Two in-put & Two out-put) The colour will be decided by Engineer - in - Charge. (Preferably In Blue, Red & Grey Colors in the ratio of 1:2:3)

Supply of Disconnect Terminal Block, Screw less type, as per RDSO Spec. No. RDSO/SPN/189/2004(Modular Terminal Blocks, Fuse Terminal Blocks &Miniature fuse link of 54 international standard for Railway signaling) With latest amendments. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply Supply of End plate for item 4.28(i) of Chapter 4 of revised SOR 2.5mm/0.091 in thick as per site requirement.

Supply of Disconnect Terminal Block, Screw less type, as per RDSO Spec. No. RDSO/SPN/189/2004(Modular Terminal Blocks, Fuse Terminal Blocks &Miniature fuse link of 55 international standard for Railway signaling) With latest amendments. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply Supply of End Stopper for item 4.28(i) of Chapter 4 of revised SOR 10mm/0.0394 in width as per site requirement.

Supply of Disconnect Terminal Block, Screw less type, as per RDSO Spec. No. RDSO/SPN/189/2004(Modular Terminal Blocks, Fuse Terminal Blocks &Miniature fuse link of international standard for Railway signaling) With latest amendments. Inspection: (i) RDSO/RITES if 56 value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply Supply of Carrier Rails for item 4.28(i) of Chapter 4 of revised SOR 35mm x 7.5mm, 1mm/0.039 in thickness un-slotted type as per site requirement.

Supply of Disconnect Terminal Block, Screw less type, as per RDSO Spec. No. RDSO/SPN/189/2004(Modular Terminal Blocks, Fuse Terminal Blocks &Miniature fuse link of international standard for Railway signaling) With latest amendments. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply Supply of Markers strip for item 4.28(i) of Chapter 4 of revised SOR

Supply of Fuse auto changeover system for Railway Signaling System as per RDSO/SPN/209/2012 rev.1 with latest amendments. One Automatic changeover Unit comprise 32 nos. of external Non Deteriorating Type or 'G' type fuses from 0.6 Amp to 4 Amp capacities which 58 are in signaling circuits. System shall have 8 cards with monitoring arrangement of 4 fuses in one card. Inspection:(i) RDSO/RITES: if value of item in work more than 5 lakhs (ii) Consignee: subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs or as per extant policy. Inspection charges:(i)Borne by Railways (ii) None Payment Terms: 100% after supply. (Per Unit should be read as Per Module)

Supply of Fuse auto changeover system for Railway Signaling System as per RDSO/SPN/209/2012 rev.1 with latest amendments. One Automatic changeover Unit comprise 24 nos. of external Non Deteriorating Type or 'G' type fuses from 4 Amp to 10 Amp capacities which are 59 in signaling circuits. System shall have 6 cards with monitoring arrangement of 4 fuses in one card. Inspection: (i) RDSO/RITES: if value of item in work more than 5 lakhs (ii) Consignee: subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs or as per extant policy. Inspection charges: (i)Borne by Railways (ii) None Payment Terms: 100% after supply. (Per Unit should be read as Per Module)

Installation wiring testing and commissioning of Fuse change over system (FACS). 60 This includes provision of common Buzzer & indication at ASM Room & ESM Duty Room and painting of fuse details. This also includes fabrication of frame for installation of FACS at Station/ LC gate where installation of relay racks not feasible. Inspection: Consignee Inspection charges: None Payment Terms: 100% on commissioning(Per Unit should be read as Per Module)

Installation, Wiring and testing of Integrated Power Supply System. This includes power distribution connection to bus bars and relay racks in the room with contractor's own wiring materials and fabrication and fixing of AC/DC power distribution board made on 10mm thick Phenolic hylam sheets or any standard make with connections suitable for 32 A. Wiring to be done considering site requirement, depending upon the load with suitable wires, lugs & glands as per 61 instructions of Engineer-in-charge. The work includes installation of Thermo flasher relay, ELD's, fixing & wiring of change over switch (program switch) for selection of DG set supply (DG1 & DG2) and wiring of change over switch (program switch) for selection of mains or DG supply. This item also includes supply & fixing of ladder along the wall for carrying power supply wires/cables from IPS room to Relay room/power room etc. Any masonry work required will be carried out by contactors own material. It includes transportation of IPS from consignee depot to work site/station/ LC gate. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution For Station

Supply of DC to DC Converter, 110V DC/24V DC, 10 Amp as per RDSO Specn.No.S- 96/2000 or latest. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% on Supply

Supply of Self Regulating Type Battery Charger,230V AC/110V DC, 60-100 Amps as per RDSO Specn.No.IRS:S-86/2000 (Amnd.4) or latest. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% on Supply

Supply of uncharged Low Maintenance Lead Acid (LMLA) secondary cell, shelf 64 mounting type conforming to RDSO Specn.No.IRS:S-88/2004 or latest with inter cell connectors, nuts and bolts etc. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply. 2V, 80 AH

Charging of Lead Acid Batteries with contractors own battery grade sulphuric acid and distilled water with minimum two charge - discharge cycles, installation of charged batteries in 65 groups & their connection & wiring. The work shall be done as per extant practice of N.W.Rly & instruction of Engineer-in-charge. Detailed measurements of initial charging shall be recorded jointly by contractor & Rly's site-in-charge. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution. 2V 80AH

Charging of Lead Acid Batteries with contractors own battery grade sulphuric acid 66 and distilled water with minimum two charge - discharge cycles, installation of charged batteries in groups & their connection & wiring. The work shall be done as per extant practice of N.W.Rly & instruction of Engineer-in-charge. Detailed measurements of initial charging shall be recorded jointly by contractor & Rly's site-in-charge. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution. 2V 300AH/ 500 AH

Supply of 4 stroke petrol driven, Kerosene operated portable Generator set self start, 67 2KVA capacity, and Petrol start kerosene run (Birla Yamaha /Honda). Original Manufacture Certificate to be Submitted. Note: - Contractor takes approval for Make/ Model No. from Engineer In-Charge before supply. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

Supply of Class 'C' Type lightening cum Surge protection safety device with visual 68 indication and potential free contacts output suitable for 110V AC application as per RDSO/SPN/172/2001 or latest. It also include transparent enclosed box. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

Supply of Class 'D' Type lightening cum Surge protection safety device with visual 69 indication and potential free contacts output suitable for 110V DC application as per RDSO/SPN/172/2001 or latest. It also include transparent enclosed box. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

Supply of Class 'D' Type lightening cum Surge protection safety device with visual 70 indication and potential free contacts output suitable for 24V DC application as per RDSO/SPN/172/2001 or latest. It also include transparent enclosed box. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

Supply of Transient Surge Suppressor Electronic Grade Surge protective device 71 (Surge) current Capacity 50 KA as per following Specifications: -1) Connection Type: Parallel, 2) Nominal discharge current: 3KA, 3) Response Time : <0.5 nanoseconds, 4) Status Indication: LEDs, Dry Contacts. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

Installation and commissioning of various classes of lightening cum surge protection 72 device as decided by site engineer. This include supply and fixing of any other material required to complete the installation & commissioning of lightening cum surge protection device. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution.

Supply of maintenance stand for relay room / battery room as per samples as per samples /drawings approved by the site engineer incharge. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after supply.

Supply of active lightening arrester of Class A for building protection as per standard NFC-17-102. It shall work on early streamer emission principle & shall be made of stainless steel with a T of 60 microseconds. Non resettable type counter shall also be supplied to count the number of lightening occurrences. It also includes supply of electrolytic copper tape of 25mmX2mm or better for connecting class A device to the earth pit. This include installation, testing and commissioning of Class A device on the top of the building. This device shall be installed at suitable height on the roof 74 of the building using a GI mast as per instructions of Railway engineer at Site. The device shall be connected to earth pit using a copper tape of 25mm x 2mm or better. This copper tape shall be run firmly only the site of the mast with the help of spacers. It shall also be ensured that the down conductor shall not touch the building throughout. the down conductor shall be connected to the earth electrode using exothermic welding. A counter shall be installed at appropriate space to count the number of occurrence. All the accessories like spacers, welding material etc. required for installation shall be arranged by the contractor. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning.

Supply of ELECTRIC POINT MACHINE 143 MM STROKE AC IMMUNITY 160V AC 75 COMPLETE WITH LOCK DETECTOR AND SLIDES FOR LOCK DETECTOR NON -TRILABLE TO OPERATE ON 110 V DC ROTARY LOCKING WITH CRANK HANDLE UNIVERSAL TPE AS PER RDSO SPECN. NO. IRS:S-24/2002 (AMND 1) RDSO DRG. NO S-10800 (ALT.5) WITH JUNCTION BOX TELESCOPIC. THE MOTOR WILL BE AS PER RDSO SPECN. NO. IRS: S-37/82 (AMND. 3) WITH RDSO DRG. NO. S-10910. This includes supply of Set of tools as per para20.1 & 20.2 of RDSO SPECN. NO. IRS:S-24/2002 (AMND 1) 20.1 The following set of tools in a suitable tool box shall be supplied along with every set of eight point machines or less. i). Hand operated square drive socket wrenches of 12.5 mm driving square (short type) as per IS: 7381 for M8, M10, M12 & M18 threads. (One 250 mm long 12.5 mm square extension bar as per IS: 7991 alongwith compatible Tee handle Square drive as per IS: 7975 suitable for above socket wrenches shall also be provided.) ii). Open jaw wrenches (spanners) for M10, M12, M20, M24 & M33 threads as per IS: 2028. iii). Adjustable wrench. iv). Screw driver 300 mm long. 20.2 Junction box and two numbers of telescopic pipes of approved type shall be supplied as an integral part of the point machine. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply.

Fixing, wiring, testing and commissioning of Electrical Point Machine on the extended sleepers at points as per std. practice and as per RDSO Drg No. SA 9151-52 or 9710 or 9161 or 10800 or 11000 as per section of rails used. Item includes fixing switch extension bracket, providing insulation for switch extension bracket, fixing ground connection, adjusting opening of the switches and adjusting the point machine with crank handle.The item also includes : (i)Complete material for installation like ground-connections, switch extension brackets, point insulation material, I pipes, wiring materials, various fixing nuts & bolts including castle nuts, spring washers (ii) All smithy & 76 fitting works required at site for complete installation. (iii) Installation of gauge tie plate & providing insulation for gauge tie plate (Insulation in William Stretcher Bar will be Provide by Railways). (iv) Wiring inside the point machine, insertion and termination of tail cable in point machine and junction boxes / location box /cable hut as per extent practice on NWR and the instruction of Railway Engineer at site. (v) Supply and fixing of suitable size GI pipes with flange for taking cable into point machine. Note ; The ground connections shall be suitable to the Point Machines as specified by Engineer-in-charge and shall be suitable to the point lay out i.e. 60 Kg. / 52 Kg / 90R as per yard layout. Electrical Point Machine and M-6 / Screw less terminals will be supplied by Railways / covered in Schedule separately Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning.

Supply of Point insulation Complete set as per RDSO/SPN/168/2005 for 1.Switch bracket'D' bracket insulation for IRS point machine - One set comprises of (a)Side plate LH to Drg.No.S-3266 - 1 No. (b) Side plate RH to Drg.No.S-3265 - 1 No. (c)Insulating bush to Drg.No.S-3199 - 4 Nos. (d) Insulating washer to Drg.No.S-8640 - 4 Nos., 2. Split-Stretcher bar 2.1 Insulation for Leading stretcher bars(BG) each set comprising of (a) Insulating plate for leading insulated stretcher bars BG as per RDSO Drg.No.T-10384 - 2 Nos. (b) Insulating bushing for leadingg insulated stretcher bars for BG as per RDSO Drg.No.T-10535- 4 Nos. (c) Insulating Washer for insulated stretcher bar BG as per RDSO drg.No.T-10371 - 6 Nos. 2.2 Insulation for following stretcher bars BG. Each set 77 comprising of: (a) Insulating side plate for insulated stretcher bars BG as per RDSO Drg.No.T-10367 - 3 No. (b) Insulating bushing for insulated stretcher bars BG as per RDSO Drg.No..T-10368 - 6 Nos. (c)Insulating washer for insulated stretcher bars BG as per RDSO Drg.No.T10371 - 12 Nos& 3. Gauge tie plates (52 Kg/60Kg as per site requirement) Insulation for (BG) complete with insulating bush and washer each set comprising of: (a) Insulating plate for insulated tie plate BG as per RDSO Drg.No.T- 10372-1 No. (b) Insulating bushing for insulated stretcher bar BG as per RDSO Drg.No.T10368 - 3 Nos. (c) Insulating Washer for insulated stretcher bar BG to IRS 40/84 as perRDSO drg.No.T-10371 - 6 Nos. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of Gauge Tie plate insulation as per RDSO/SPN/168/2005 as per RDSO drg No: T- 10372Alt2, T- 10368, T- 10371Alt2, T-15083/88/Alt2 & T-11690/Alt2 and as per RDSO/SPN/168/2005 with latest amendments as applicable. Gauge tie plates (52 Kg/60Kg as per site requirement) Insulation for (BG) complete with insulating bush and washer each set comprising of: 78 (a) Insulating plate for insulated tie plate BG as per RDSO Drg.No.T-10372-1 No. (b) Insulating bushing for insulated stretcher bar BG as per RDSO Drg.No.T10368 - 3 Nos. (c) Insulating Washer for insulated stretcher bar BG to IRS 40/84 as perRDSO drg.No.T-10371 - 6 Nos. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of Ground connections, complete set suitable for IRS type / approved point Machine for ordinary turnout with tongue attachment insulation and other insulation as per RDSO Drg. S/3361@ 47>47@ 63 (for IRS type point machine) or RDSO Drg No.SA-9151/52 (for Siemens point machine) with latest amendments. However the ground connection shall be procured only after confirmation from Railway engineer as per site condition /type of machine/turnout. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of Ground connections, complete set suitable for IRS type/approved point Machine for derail switch with tongue attachment insulation as per RDSO Drg. S/3361@ 47>47? 40@for IRS type point machine) or RDSO Drg No. SA 9151/52 (for Siemens point machine) with 80 latest amendments. However the ground connection shall be procured only after Confirmation from Railway engineer as per latest site condition /type of machine/turnout. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of William Stretcher Insulation Set (complete) as per RDSO/SPN/168/2005 with insulating bush and washer to suit point layout and conforming to RDSO Drg.No.T-10372 or latest, T- 10368 or latest and T-10371 or latest. 1.1 Insulation for Leading stretcher bars(BG) each set comprising of (a) Insulating plate for leading insulated stretcher bars BG as per RDSO Drg.No.T- 10384 - 2 Nos. (b) Insulating bushing for leadingg insulated stretcher bars for BG as per RDSO 81 Drg.No.T-10535- 4 Nos. (c) Insulating Washer for insulated stretcher bar BG as per RDSO drg.No.T- 10371 - 6 Nos. 1.2 Insulation for following stretcher bars BG. Each set comprising of: (a) Insulating side plate for insulated stretcher bars BG as per RDSO Drg.No.T-10367 - 3 No. (b) Insulating bushing for insulated stretcher bars BG as per RDSO Drg.No..T-10368 - 6 Nos. (c)Insulating washer for insulated stretcher bars BG as per RDSO Drg.No.T10371 - 12 Nos Inspection: (i) RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of Track feed Battery Charger as per RDSO Specn. No.IRS: S-89/2013 Ver.1.0 or latest. Charging Capacity Rating 10 Amps for Charging 80 AH Battery. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply.

Supply of Adjustable Track Feed Resistance 30 Ohms (Disc Type) as per RDSO Drg. No.SA-20161-66/M or latest. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply. Per Track

Fixing and wiring of DC track circuit equipments i.e. track feed charger, resistance, track relay, battery, B type choke etc., in the Apparatus Case and battery box as per standard 84 practice. Termination of tail cable on M 6 / Screw less terminals WAGO or FINOLEX or similar approved make teminals/ fuse blocks / HRC fuse. Item includes testing /commissioning of track circuit. Complete wiring material will be supplied by contractor. (Supply of Track feed battery charger, track feed battery, resistances & 'B' type choke & Track relays, ARA terminal/Modular terminals wago/phoenix contact type will be supplied by Railways / covered in Schedule separately). Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution. Per Track

Installation of DC track circuits covering all types of Track circuts including points zones also.The item includes provision of doubled continuity GI wire bonds on rail joints after drilling bond-hole of 7.0/7.2mm dia, skimming of fish plate, insertion of insulated block joint( if required), 85 fixing of TLJB (separate for positive & negative rails) with angle iron for track feed/jumper/track relay ends of track circuits and also for fixing jumper cables as per approved Track Circuit Plan, making rail connections through suitable insulated sleeves from TLJB at TF, jumper & TR end with GI wire, rail clips for fixing bond wire on the TLJB as per standard practice, termination of tail cables on TLJB terminals etc. TF/TR wiring shall be fixed on the suitable arrangement on PRC sleepers with the help of Hooks. In case Engineer at site desires that jumpering from TLJBs is to be done using signalling cable 2 coreX 2.5 sqmm , contractor shall provide the jumpering cable using 2 X 2.5 sqmm signalling cable.The signalling cable will be supplied by Railways. Hooks shall be provided on PRC sleepers with the help of suitable steel bracket. This item also includes fixing & supply of channel pins, Hooks etc. The item does not include includes supply of TLJB as per RDSO Drg.No.RST-11509 or latest as per technical specs Installation of of Track Lead Junction Box(TLJB) as per Drg.No.RST-11509 or latest made from FRP material including brass bolts and hylam board sheet with terminals etc. (a) Installation and commisssioning of TLJB complete with cover to be in black/red having approximate weight of 4.0 Kg with L-262mm W-212mm and H 90 mm and all the holes required for mounting on FRP stump (verticall two for each FRP angle) HDPE pipe , cable etc. (b) Installation and commisssioning of Each TLJB having two bakellite terminal block fitted horizontally : each bakellite terminal block shall have two nickel chrome plate M10 brass terminal, 50mm long.Alongwith each TLJB , nickel chrome plated brass links(two nos.0f adequate strength for vertical linking of the terminals to be wired and fixed properly. (c) Installation of HDPE pipe of size 32/35mm , 380 mm long alongwith two nuts for fixing on the TLJB hole . (d) Installation of the FRP stump for mounting the TLJB to be made of one meter long 30mm X30mmX 4mm angle(2 nos.) and 300mm long 30mm X30mmX 4mm angle(1 no.) fixed at 50 mm from the bottom using galvanised nuts and bolts.The TLJB and the angles for stump should be fixed in given holes on them for fixing using galvanised nuts and bolts . Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution.

Supply of Track Lead Junction Box(TLJB) as per Drg.No.RST-11509 or latest made from FRP material including brass bolts and hylam board sheet with terminals etc. The technical specifications are as follows: (a) TLJB complete with cover to be in black/red having approximate weight of 4.0 Kg with L-262mm W-212mm and H 90 mm and all the holes required for mounting on FRP stump (verticall two for each FRP angle) HDPE pipe , cable etc. (b) Each TLJB shall have two bakellite terminal block fitted horizontally : each bakellite terminal block shall have two nickel chrome plate M10 brass terminal, 50mm long.Alongwith each TLJB , nickel chrome plated brass 86 links(two nos.0f adequate strength for vertical linking of the terminals to be supplied. (c) HDPE pipe of size 32/35mm , 380 mm long alongwith two nuts for fixing on the TLJB hole . (d) The FRP stump for mounting the TLJB to be made of one meter long 30mm X30mmX 4mm angle(2 nos.) and 300mm long 30mm X30mmX 4mm angle(1 no.) fixed at 50 mm from the bottom using galvanised nuts and bolts.The TLJB and the agles for stump should come alongwith holes on them for fixing using galvanised nuts and bolts of adequate strength to be supplied alongwith TLJB drawing no. 11509. Inspection: (i) RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of B Type Choke as per RDSO Specn.No.IRS:S-65/83 (Amnd. 1) or latest. Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after supply.

Supply of Channel Pins MS (Galvanized) single groove, 7 mm suitable for 4mm dia bonding wire as per spec No IRS S 17 & RDSO Drg No. S-69/M. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

Supply of GI wire 8 SWG (4mm dia) suitable for track circuit rail bonding. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

Provision/Installation of bonding with GI wire 4mm dia ( 8 SWG) for track jumper & 90 fish plate joints bonds. This will include drilling of 7.0/7.1/7.2 mm dia holes in rails (4 Nos.) and provision of two jumpers for each bond, clipping of bonds etc. with contractors own tools as per instruction of Rly. Engineer at site. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Execution.

Supply of Hydrometer, Exide make or similar for measuring specific gravity of Battery Graded acid with mounting stand in location Boxes. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Supply.

Installation and commissioning of Central Evaluator of axle Counter, wiring from CT rack to Central Evaluator, installation and wiring of the reset box, LV box (if required) and associated power supply wiring. This includes supply of shielded cable of required conductor size for wiring 92 between CT rack to evaluator rack, all other wires, power supply cable and wiring materials. The power supply cable from power room to Central Evaluator should not be lass than 10 sq.mm PVC wire. Earthing as per OEM's guidelines & specification with their own material. This also includes painting and writing work on evaluator as per site requirement. NOTE: Installation/ programming/ configuration/ commissioning of Axle counter equipment to be carried out in accordance with latest guidelines issued by Railways/ RDSO preferably by Authorised representative of OEM. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning.

Installation of track device (double rail contact) including digging of trench, track crossing, laying of anti-rodent, anti-oxidant & non-flame propagating type Double Walled Corrugated (DWC) pipe as per IS- 14930 part- I or II or latest and all other accessories as per site requirement to 93 be for laying of transmitter and receiver cable. The item also includes installation of EJB / Track side Electronics including foundation & earthing as per OEM's guidelines and Technical requirement & specification. NOTE: Installation/ programming/ configuration/ commissioning of Axle counter equipment to be carried out in accordance with latest guidelines issued by Railways/RDSO preferably by Authorized representative of OEM. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Installation, testing and commissioning of SSBPAC(Digital) for Single Line/Double lineas per RDSO Specification No. RDSO/SPN/175/2005 Ver. 1 or latest alongwith station master block panel alonwith DTMF based Electronic Block Bell & Block Telephone equipment as per 94 specification No RDSO/SPN/191/2005(Ver. 0) or latest , Microprocessor Lighting & Surge protection Devices for power line 24 DC Class-C, Lighting & surge protection devices for DATA Line Class-D,EKT for Shunt Key as per Drg. no. SA-22601/Alt.4 & IRS: S-21/2001 and associated data cable including wired relay rack without relays.( Required relays for this item will be supplied by Railways) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after commissioning.

Supply of Automatic Media changeover Card for SSBPAC(D) which includes One Voice 95 Modem Circuit and One E1 Converter Circuit, for working on redundant channels for data transmission on OFC/Quad. Necessary Lightning & Surge protection devices for data lines need to be provided. Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after Supply.

Installation and commissioning of Automatic Media changeover Card for SSBPAC(D) 96 which includes One Voice Modem Circuit and One E1 Converter Circuit, for working on redundant channels for data transmission on OFC/Quad. Necessary Lightning & Surge protection devices for data lines need to be provided. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after commissioning.

Supply of hand operated track drilling machine for bonding hole. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Installation of LED signals lamps for auxiliary/subsidiary signals/main signals (i.e. 98 route, shunt , calling on, Red , Yellow, Green) as per instructions given by engineer incharge. The contractor will supply all materials required for installation. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning.

Supply of Colour Light Signal Complete. This includes: - (1). Post Tubular 140 mm Dia, as per IRS: S-6/81 or Latest & RDSO Drg. No. SA-24625 (Advance). (2). CI Base (As per IRS S-10 & RDSO Drg. No. 2011/M with latest assembly). (3). Number plate to Drawing No. S 23149 Alt.1 =1 No , Number plate clamps to Drawing No. S 23148 Alt.1 =2 no (4). Ladder Assembly, as per RDSO Drg. No. SA-23156, with Base, Ladder Guard rail (complete) to Drawing No. SA 23138 Alt.1(1No), Platform to Drawing No. SA 23134 Alt.1(1 No), Front Maintenance Platform, MS Supporting bracket to Support 99 Ladder.Ladder stay (small) to Drawing No. S 23159 Alt. 1 (2 Nos.) , Ladder stay (large) to Drawing No. S 23160 Alt. 1 (2 Nos.) , Ladder section to Drawing No. SA 23157 Alt. 1(1 Nos.)Stay clamp to Drawing No. SA 2062/M (2 no), Rail Clamp to Drawing No. S 2066/M (1 No.) (5). Signal Front Staging Complete Assembly for CLS Unit. (6). Signal back staging as per extent NWR Practice. Note: Note: Height of the Post shall be 5.5 Long. Inspection: (i)RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of Offset brackets for Main Signal, made of tubular steel, outer diameter 140 mm, thickness of pipe 4.5 mm. horizontal length of pipe 545 mm & vertical length of pipe 324 mm with fixing arrangement on Main Signal post as per Drawing No SW/554/G/R Inspection: (i)RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of Offset brackets for Shunt Signal, made of tubular steel, outer diameter 89 mm, thickness of pipe 4.5 mm. horizontal length of pipe 324 mm & vertical length of pipe 324 mm 101 with fixing arrangement on Shunt Signal post as per Drawing No SW/354/I Inspection: (i)RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Erection of CLS Post with base and signal unit on top or on OFFset Bracket, fixing of front and back staging, ladder and guards, signal name plates / boards if any with contractor's own brackets and fixing materials. This also includes erection of auxiliary signals like calling on, shunt 102 signal if any. The work shall be done as per instructions of Rly engineer at site. It also includes provision & fixing of maintenance platform as per design given by Engineer -In-Charge at site. The Item includes cutting of Signal post if required by Site In charge. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning. 2/3/4 aspect signal unit mounted on offset bracket with junction type route indicator 1/2/3/4/5/6 or multilamp lamp route indicators/Stencil type rout indicator mounted on signal post.

Erection of CLS Post with base and signal unit on top or on OFFset Bracket, fixing of front and back staging, ladder and guards, signal name plates / boards if any with contractor's own brackets and fixing materials. This also includes erection of auxiliary signals like calling on, shunt 103 signal if any. The work shall be done as per instructions of Rly engineer at site. It also includes provision & fixing of maintenance platform as per design given by Engineer -In-Charge at site. The Item includes cutting of Signal post if required by Site In charge. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning. 2/3/4 aspect signal unit mounted mounted directly on signal post.

Supply of Non Metallic (FRP) colour light signal housing multi unit type for railway signaling suitable for RE area TWO Aspects. Complete without lenses, lamps and signal transformer 104 as per RDSO DRG. No. SA 23001/A/M Adv. Alt- S and as per SPEC. No. RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP material as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest. Inspection: (i)RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of Non Metallic (FRP) colour light signal housing multi unit type for railway signaling suitable for RE area THREE Aspects. Complete without lenses, lamps and signal transformer as per RDSO DRG. No. SA 23001/A/M Adv. Alt- S and as per SPEC. No. 105 RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP material as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest. Inspection: (i)RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of Position Light Shunt Signal Unit Complete with Post(made of GI Pipe of 80 mm Diameter Medium Class IS Spec. No. IS: 1239 Pt. 1/1990, Base, Hood, Cover etc as per Drg. No. 106 SA-23840 suitable for LED Signal Lighting Unit.(Supply of LED Unit is not covered in this item) Inspection: (i)RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Erection of Position Light Shunt signal with Base, Post, Signal unit and fixing of Number Plates. The work shall be done as per instructions of Rly engineer at site. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning.

Supply of Position Light Shunt Signal Unit Complete, with offset bracket, hood, Cover etc as per Drg. No. SA-23840 suitable for LED Signal Lighting Unit.(Supply of LED Unit is not covered in this item)Inspection: (i)RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Erection of Position Light shunt signal on Offset bracket on main signal. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning.

Supply of Junction route indicator unit 3 ways (Without Lenses & Holder) as per Drg. No. RDSO SA 23403 suitable for LED Signal Lighting Unit & as IRS:S-66/84 amndt-1 or latest.(Supply 110 of LED Unit is not covered in this item) Inspection: (i)RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Fixing of Junction type Route Indication 1-Way/2-Way/3-Way/4-Way/5-Way/6-Way on the top of the signal post. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning.

Supply of Calling ON Signal Unit with Brackets & Fixing accessories. Calling On Signal 112 Unit shall conform to RDSO Drg no 24351(Adv) Alt1 suitable to LED Signal Lighting Unit. Inspection: (i)RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Fixing of Calling-on Signal/A-Sign/AG-Sign unit on signal post. The item includes fixing 113 of Co- On signal /'A' sign/ 'AG' sign unit on signal post with bracket, hood etc. Item includes supply of bracket & fixing materials etc. by the contactor. The item also includes termination of cables & wiring inside Co- On signal /'A' sign/ 'AG' sign unit as per standard practice. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning.

Supply of Different warning Boards / Calling on Board used for Railway Signalling 114 system as per RDSO Drg. No. SA2380 (Adv). This includes Painting and retro reflective arrangement should be as per SEM. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Fixing of Stop Board, Block section limit Board, Shunting Limit Board, goods warning 115 board , Calling on Board with contractors own material. This excludes supply of Stop Board / Block section limit Board / Goods warning board/Calling on board. The work shall be done as per instruction of Rly Engineer at site. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

Supply, Fabrication and fixing of Signal Number Plate( CSTE Drg No CSTE/6186) , 'A' Marker (Drg No. CSTE/6180), 'AG' Marker (Drg No. CSTE/6181), 'P' Marker (Drg No. CSTE/6182), 116 Arrow Marker (Drg No. CSTE/6183), 'G' Marker (Drg No. CSTE/6184), 'C' Marker (Drg No. CSTE/6185). marker disk on signals as per standard practice All material required for this work shall be supplied by Contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

Supply and fixing of protective screen of expanded metal 12 SWG of size 1200 x 1500 mm on signals as per std. practice in RE Area. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

Casting of CC Foundation for Signal Post in the ratio of 1:3:6 as per Drg.No.CSTE/NWR/SOR/21/A using standard size of foundation/galvanized holding down bolts 118 required for erection of colour light signal post. Item includes excavation, ramming of CC using vibrator, curing and plastering with 1:4 cement-sand mixture (aggregate will not exceed 3.8 cm). Aggregate, cement, sand and holding down bolts will be supplied by contractor. Any machines & tools, if required for execution of this item, will be arranged/provided by contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

Casting of C.C. Foundation for Position Light Shunt Signal/ Indicator/SPI as per Drg.No.CSTE/NWR/SOR/ 22 in ratio 1:3:6 by using standard size of galvanized holding 119 down/foundation bolts. Item includes excavation, ramming of CC using vibrator, curing and plastering with 1:4 cement sand mixture. Aggregate cement, sand and holding down bolts, will be supplied by contractor. Any machines and tools, if required for execution of this item, will be arranged/provided by contractor. Note: As per available site conditions, if sizes of foundations are required to be decreased/ increased and same has been approved/agreed by engineer incharge then variation in CC work will be calculated on volumetric basis as per rates of these items. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation. ."

Cement concrete work for miscellaneous items in ratio 1:3:6. Item includes 120 excavation, ramming of CC by using vibrator, curing and plastering with cement and sand mixture (aggregate will not exceed beyond 3.8 cm). The aggregate cement and sand will be supplied by contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.(Unit is per cubic meter)

Supply of Electrically Operated Lifting Barrier complete set suitable for 110VDC/24V DC (option to be specified in tender specifically of either 110 V DC or 24V DC)supply without hand generator back up & motorized boom locking arrangements as per RDSO Spec. SPN/208/2012 with latest amendment. One set consisting 02 Nos of Barriers of length 09.76 Mtrs. along with Spares & tool kit mentioned in RDSO Spec. SPN/208/2012 clause 10.1 & 10.2 as below 10.1 Following spares 121 shall be supplied alongwith each set (02 nos.) of Electric lifting barrier as per requirement of the purchaser i) GI boom - 1 no. complete. ii) Belt - 1 no. iii) Crank handle - 1 no. iv) Motor Contactor - 1 no. v) Motor protection MCB- 1 no. vi) Push button complete- 2 nos. vii) Limit switch - 3 nos. (1 lever type and 2 top roller type) viii) Fuses used - 2 sets 10.2 Tool kit consisting of standard sizes of wrinch/ spanner and Allen keys should also be supplied with each set (02 nos.) of Electric Lifting barrier. Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after Supply.

Supply of Yellow Retro reflective sheet for LC Boom prismatic grade reflective sheets of size 305 x 290 mm one set consist 18 pieces. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% on Supply

Supply of Dual Tone Bell /Buzzer with Flasher arrangement and 20 Watt horn working on 24 V DC/ 110 V AC for warning road users at LC gates. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply

Supply of (02) nos. electrical lifting barrier booms of 9.76 meter each as per DRG 124 RDSO/S 11600 . The material will be as per RDSO Specn.No.RDSO/SPN/208/2012/Ver.2.0 and Amendment 1 or latest. Inspection: Consignee subject to procurement from RDSO approved supplier. Inspection Charges: None. Payment Terms: 100% after Supply

Supply of Sliding type mechanical Boom barrier assembly 11 to 12 Meter Long, 125 movement drive mechanism, resetting & supporting stand suitable for Mechanical/Electrical level crossing gate as an emergency arrangements as per Drg. mentioned in the tender document. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply

Casting of CC foundations in the ratio of 1:3:6 for sliding boom as per Drg. Minimum 126 10 Nos of foundation per set shall be cast using standard size holding down bolts & nuts for erection. Item include excavation, ramming, curing and plastering 1:4 cement and sand mixture. Aggregate, cement, sand and holding down bolts & nuts to be supplied by the contactor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation

Supply of professional LED VDU monitor of display size 42 inch. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Office Chair make Godrej CH-7B or similar of reputed brand. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Steel Plain Almirah with 4 adjustable slavesSize: 1980mm height, 915 mm width and 485 mm depth.Make: Godrej Storewel Plain Large or Similar of reputed brand. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Microprocessor based Networkable Analogue Addressable up to 64 nodes 1 Loop Fire Alarm Control panel with LCD display, the panel should be equipped with sufficient nos. of loop as per RDSO Specification No. RDSO/SPN/217/2018 ver 2.0 or latest. Each loop shall have 130 capacity of 127 analogue addressable devices in 1 loop, the panel shall have sufficient nos. of programmable relay control for controlling AHU's, pressurisation fans, ventilation fans at fire pump room, monitoring of fire sprinkler & sealed lead acid batteries sufficient for 24 Hours normal working & then capable of operating the system for 24 Hours during Emergency conditions as required. The panel shall have provision of connectivity of BACNET/ MODBUS/ LONWOK/TCP-IP. The panel shall have dedicated RS232 serial port for direct PC or MODEM connection, optional remote printer as per RDSO Specification No. RDSO/SPN/217/2018 ver 2.0 or latest Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation ,Testing and Commissioning of Microprocessor based Networkable 131 Analogue Addressable up to 64 nodes 1 Loop Fire Alarm Control panel with LCD display, the panel should be equipped with sufficient nos. of loop as per RDSO Specification No. RDSO/SPN/217/2018 ver 2.0 or latest. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning.

Supply of Probe type bimetallic Heat Sensor/Fixed cum ROR 90 degree with required 132 module to be communicated with main fire Alarm Panel as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation ,Testing and Commissioning of Probe type bimetallic Heat Sensor/Fixed 133 cum ROR 90 degree with required module to be communicated with main fire Alarm Panel as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning

Supply of intelligent Analogue Addressable Multi-Sensor type smoke detector with inbuilt fault isolator and integral response indicator with 360 degree viewing angle. Detector shall 134 communicate 3 danger levels for differentiated alarm activation and high tolerance to dust, dirt, temperature fluctuations and air current. Detector should have unique address for communication and assigned through panel with mounting base as required with the protection category of IP 40. All items as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest. Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation, testing and commissioning of intelligent Analogue Addressable Multi- 135 Sensor type smoke detector with inbuilt fault isolator and integral response indicator with 360 degree viewing angle as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest. Inspection: Consignee Inspection Charges:Borne by Railways Payment Terms: 100% after commissioning

Supply of Analogue Addressable Manual Call Point with integral short circuit isolator, 136 Analogue addressable protocol having status LED for alarming & standby mode, Electronically addressed) as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation ,Testing and Commissioning of Analogue Addressable Manual Call Point 137 with integral short circuit isolator, Analogue addressable protocol having status LED for alarming & standby mode, Electronically addressed) as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning

Supply of UV/IR Type Flame detector with required module to communicate on main fire alarm panel as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest. Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation ,Testing and Commissioning of UV/IR Type Flame detector with required 139 module to communicate on main fire alarm panel as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning

Supply of Linear Heat Sensing (LHS) cable as per RDSO Specification No. RDSO/ SPN/ 140 217/ 2018 ver 2.0 or latest Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation of Linear Heat sensing (LHS) cable as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution.

Supply of LHS interface module as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest. Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation of LHS interface module as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution.

Supply of Air Sampling Type detector shall use LASER type. This type of detector shall use piping or tubing distribution network that shall run from the detector to the area as to be 144 protected. It should be supplied with required module & Power supply unit complete as a system with all accessories like pipes, Sampling points etc as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation ,Testing and Commissioning of Air Sampling Type detector (it shall use LASER type) as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning

Supply of intelligent Addressable Loop Powered Sounder cum beacon with base 146 inbuilt fault isolator with protection category of IP42 and duly approved as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation, testing and commissioning of intelligent Addressable Loop Powered 147 Sounder cum beacon with base inbuilt fault isolator with protection category of IP42 and duly approved as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: Consignee Inspection Charges:None Payment Terms: 100% after commissioning.

Supply of FRLS unarmoured/armouredcable(2Cx1.5 sq.mm) with all accessories for connection of all Fire Alarm devices as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation ,Testing and Commissioning of FRLS unarmoured/armouredcable(2Cx1.5 149 sq.mm) with all accessories for connection of all Fire Alarm devices as per RDSO Specification No. RDSO/ SPN/ 217/ 2018 ver 2.0 or latest Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning.

Supply of CO2 type fire extinguisher capacity 4.5 Kg capacity ISI Mark IS: 15683 150 operating temperature (-30) ° to (50) ° for class 13 B type of fire with 1 mtr. Hose pipe fitted with PVC bend horn complete in all respect. Inspection: (i) RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges:(i) Borne by Railways (ii) None Payment Terms: 100% after Supply.

Supply of Apparatus Case Single(Large) NE Rly Type as per Drg. No. CSTE/6088 fitted with two nos of E Type lock (ward No will be specified by Engineer-in Charge) as per RDSO Drg. No. SA 3376 and Key to Drg. No. 3377 as per RDSO drawing No. RDSO/S-11500. Note: This item includes 151 the supply of 2 Nos E Type Lock fitted on both doors, along with two Keys. Inspection: (i) RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee subject to procurement from RECOMMENDED LIST OF FIRMS FOR MECHANICAL SIGNALLING ITEMS if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges:(i) Borne by Railways (ii) None Payment Terms: 100% after Supply.

Installation of Apparatus Cases Single(Large) with 'E' type lock on CC foundation. This 152 includes filling of location foundations with river bed sand and plastering on top of the sand. Supply of 'E' Type lock has been covered in supply of Apparatus case separately. It covers fixing of lamp holder , switch and lamp etc. in Apparatus Case. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation.

Supply of Apparatus Case half (Medium) NE Rly Type as per Drg. No. CSTE/6088 fitted with two nos of E Type lock (ward No will be specified by Engineer-in Charge) as per RDSO Drg. No. 153 SA 3376 and Key to Drg. No. 3377 as per RDSO drawing No. RDSO/S-11507. Note: This item includes the supply of 2 Nos E Type Lock fitted on both doors, along with two Keys. Inspection: (i) RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee subject to procurement from RECOMMENDED LIST OF FIRMS FOR MECHANICAL SIGNALLING ITEMS if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges:(i) Borne by Railways (ii) None Payment Terms: 100% after Supply.

Installation of Apparatus Cases Half (Medium) with 'E' type lock on CC foundation. 154 This includes filling of location foundations with river bed sand and plastering on top of the sand. Supply of 'E' Type lock has been covered in supply of Apparatus case separately. It covers fixing of Location lamp holder , switch and lamp etc. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation.

Excavation and Casting of Apparatus Case foundation in ratio 1:3:6 with contractor's own materials including cement and galvanized anchor bolts of standard size. The required 155 scaffolding Ferma etc for Casting of foundation will have to be brought by the contractor at his own cost.The item also includes additional masonry work as well as earthwork if required on bank where there will be possibilities of foundation sinked, fallen or tilted. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation. Single (Large) Case Apparatus case / SS location box as per Drg No. CSTE/5074

Excavation and Casting of Apparatus Case foundation in ratio 1:3:6 with contractor's own materials including cement and galvanized anchor bolts of standard size. The required 156 scaffolding Ferma etc for Casting of foundation will have to be brought by the contractor at his own cost.The item also includes additional masonry work as well as earthwork if required on bank where there will be possibilities of foundation sinked, fallen or tilted. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation. Half (Medium) Case Apparatus case / SS location box as per Drg No CSTE/5074

Supply of Phenolic laminated Sheet, grade P3 in standard size of 1220 X 1220 x 20 157 mm as per spec. No IS 2036 of 1995 or latest. Test report of manufacture to be supplied. Inspection: (i) RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee Inspection Charges:(i) Borne by Railways (ii) None Payment Terms: 100% after Supply.

Supply of Phenolic laminated Sheet, grade P3 in standard size of 1220 X 1220 x 10 158 mm as per spec. No IS 2036 of 1995 or latest. Test report of manufacture to be supplied. Inspection: (i) RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee Inspection Charges:(i) Borne by Railways (ii) None Payment Terms: 100% after Supply.

Fabrication and fixing of phenolic laminated sheet of size 10/12/20 mm thick in 159 location box by providing all fixtures as per Railway Drawing including fixing of PVC coated string rods at the back side for cable support with contractor's own materials. The work shall be done as per instructions of Rly engineer at site. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation. Single Case (Large Case)

Fabrication and fixing of phenolic laminated sheet of size 10/12/20 mm thick in 160 location box by providing all fixtures as per Railway Drawing including fixing of PVC coated string rods at the back side for cable support with contractor's own materials. The work shall be done as per instructions of Rly engineer at site. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation. Half Case (Medium Case)

Fixing of ARA(M-6) Terminals /Screw less connectors / modular disconnect terminal 161 blocks and fuse blocks on phenolic laminated sheets and fixing by stainless steel/brass nuts & bolts. This includes provision of two additional holes on the board on either side for cable conductor entry. (Supply of all above terminals have been covered separately in Chapter 4 of SOR) Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation.

Supply of Round head type non deteriorating type low voltage cartridge fuse as per Spec No IRS/S/78/92 with latest amendments 2A/4A/6A capacity. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after supply.

Supply of Tic-tac Piano type Switches , 5A (ISI mark of reputed make) Inspection: Consignee Inspection Charges: None Payment Terms: 100% after supply

Supply of two pin Lamp holder Bakelite type for Apparatus Cases (ISI mark of reputed make) Inspection: Consignee Inspection Charges: None Payment Terms: 100% after supply

Fixing of KLCR relays in field in half location boxes if Gate lodge is not provided or at any other location as decided by engineer in charge. Item includes supply and fixing of MS sheet and wiring of KLCR relays, push buttons and LEDs for KLCR circuit. The KLCR relays, push buttons, LEDs 165 will be fixed on a MS sheet of min. 3mm in the half location box. The MS sheet will cover full length and breadth of the half location box and divided in two pieces of approx. 48cm x 46cm and 80cm x 46cm. The first piece to be fitted on top and will contain the KLCR relays, LEDs and push buttons. The second piece to be fitted below the first piece. (Supply of KLCR relays covered in separate item of SOR). Inspection: Consignee Inspection Charges: None Payment Terms: 100% after installation.

Supply of Medium class GI pipes 100 mm dia(4.5 mm thickness) as per IS 1239 ( Part 1 ) : 2004 with coupling on culverts bridges as per Drg.No.CSTE/NWR/SOR/06 to 12 or at any other 166 locations as decided by Site Engineer. It includes supply of all material required for fixing arrangement. Contractor will also supply flexible/corrugated HDPE pipe at the end of GI pipe to protect the cables from sharp edges and sudden bends. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Fixing of Medium class GI pipes 100 mm dia(4.5 mm thickness) as per IS 1239 ( Part 1 ) : 2004 with coupling on culverts bridges as per Drg.No.CSTE/NWR/SOR/06 to 12 or at any other 167 locations as decided by Site Engineer. It includes installation of all material required for fixing arrangement. Contractor will install flexible/corrugated HDPE pipe at the end of GI pipe along with any masonry work(if required) to protect the cables from sharp edges and sudden bends. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after installation.

Supply of Medium class GI pipes 50 mm dia(3.6 mm thickness) as per IS 1239 ( Part 1 168 ) : 2004 for use in ASM room and at any other location as decided by Site Engineer. It includes supply of all material required for fixing arrangement. At the ends of GI pipe, flexible/corrugated HDPE pipe will be provided by contractor to protect cables from sharp edges and sudden bends. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Fixing of Medium class GI pipes 50 mm dia(3.6 mm thickness) as per IS 1239 ( Part 1 ) : 2004 for use in ASM room and at any other location as decided by Site Engineer. It includes 169 installation of all material required for fixing arrangement. At the ends of GI pipe, flexible/corrugated HDPE pipe along with any masonory work(if required) will be provided by contractor to protect cables from sharp edges and sudden bends. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Installation.

Supplying and placing of one layer of standard size of B grade quality bricks of the 170 local make spreading on cables laid.(minimum size of brick 200mm X 100mm X 70mm) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Installation. Lengthwise (up to 2 cables).(Unit is per RM Running Meter)

Supplying and placing of one layer of standard size of B grade quality bricks of the 171 local make spreading on cables laid.(minimum size of brick 200mm X 100mm X 70mm) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Installation. widthwise ( more than 2 cables).(Unit is per RM Running Meter)

Supply of Double Walled Corrugated (DWC) HDPE Pipe/duct with associated collars etc. as per RDSO Specification No. RDSO/SPN/204/2011 or latest anti-rodent & anti-oxidant and non flame propagating type in 6 meters straight length and of size 120 mm outer dia,& 103.5 mm inner dia. (The manufacturers, suppliers must produce valid IS license and should be certified under ISO 9000 and shall submit copy of certificate). One of the following coupling arrangements should also 172 be supplied with each pipe as per the site requirement. 1) Suitable snap fit coupler with rubber O- Ring 2) Spacers 3) Tees 4) Bend, 5) End-cap (The total quantity of above items is equal to no. of pipes supplied.) DWC pipe shall be marked at every 1 mtr length in such a way that manufacturer's name, vendor name and year of manufacture can be easily identified. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply

Supply of Double Walled Corrugated (DWC) HDPE Pipe/duct with associated collars etc. as per RDSO Specification No. RDSO/SPN/204/2011 or latest anti-rodent & anti-oxidant and non flame propagating type in 6 meters straight length and of size 50 mm outer dia, & 38 mm inner dia. 173 (The manufacturers, suppliers must produce valid IS license and should be certified under ISO 9000 and shall submit copy of certificate). One of the following coupling arrangements should also be supplied with each pipe as per the site requirement. 1) Suitable snap fit coupler with rubber 'O-Ring 2) Spacers 3) Tees 4) Bend, 5) End-cap (The total quantity of above items is equal to no. of pipes supplied.) DWC pipe shall be marked at every 1 mtr length in such a way that manufacturer's name, vender name and year of manufacture can be easily identified. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply

Supply of Double Wall Corrugated (DWC)-HDPE pipe/duct of size 200 mm outer dia, & 175 mm inner dia. It includes supply of Double Wall Corrugated -HDPE pipe/duct as per RDSO Specn.No. RDSO/SPN/ 204/2011 (version 1.1) or latest and conforming to ISI Spec. No.IS:14930, Part- II. (The manufacturers, suppliers must produce valid IS license and should be certified under ISO 9000 and shall submit copy of certificate). One of the following coupling arrangements should also 174 be supplied with each pipe as per the site requirement. 1) Suitable snap fit coupler with rubber O- Ring 2) Spacers 3) Tees 4) Bend, 5) End-cap DWC pipe shall be marked at every 1 mtr length in such a way that manufacturer's name, vendor name and year of manufacture can be easily identified. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply

Supply of Half Round RCC pipes & collars of 300 mm outer dia & 250 mm internal dia (2 meter long) along with collars as per IS No. 458/2003 of NP type Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply of Half Round RCC pipes & collars of 150 mm internal dia (2 meter long) along with collars as per IS No. 458/2003 of NP type Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Laying of half round RCC pipe after laying the cables in the trenches. (Cable laying is covered separately) Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.(Unit is RM running meter)

Supply of Thermo shrink Universal Jointing kit for Quad Cable (for straight joints) as per RDSO spec IRS/TC-77/2012 revision 3 With latest Amd. Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply

Jointing of 4 / 6 quad /Signaling cable with Heat Shrinkable straight through Jointing Kit. All the material required for the work are to be arranged by contractor himself at his own cost 179 except Thermo shrinkable Joint Kit/Rapid Joint kit. After jointing the cable through test such as insulation test, continuity cable losses etc. to be carried out jointly with Railway Engineer. If any defect or any damage is observed during jointing, the contactor has to redo the joint free of cost. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

Horizontal direction drilling/boring without damage of surface road /track using Auger Machine(HDD machine). The bore shall be upto 200 mm dia & shall be done at the depth of minimum 1200 mm from the ground level. The ground level shall be considered ignoring the bank 180 height of the bank of the road. The length of the bore shall be minimum 4 Mtrs long. This include insertion of different dia DWC-HDPE pipe/ GI pipes coupling etc. as per direction of Engineer In charge. Note:- Pipe Supply is not covered under this item. Contactor shall provide all material required for boring and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Horizontal Drilling by using manual pushing method at minimum depth of 1.5 meter 181 below the formation level of earth as per decision of Engineer in charge .Pipe Supply is not covered under this item Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

Supply of RCC cable route marker engraved and painted on both side along the route at every 50 meter and route diversion as per Drg. No 4014/00/CC4 or latest/ Stone marker. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply

Transportation at site and Installation of RCC cable route marker engraved and 183 painted on both side along the route at every 50 meter and route diversion as per Drg. No 4014/00/CC4 or latest/ Stone marker. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

Excavation of cable trench as per cable route plan, 1.2 Mtr. deep and of 0.3 Mtr. to 0.6 Mtr. wide at bottom as per RDSO sketch No. SDO/CABLE LAYING/003 or latest alongside the track in normal (all type) soil/strata, conforming to distances as per cable route plan and refilling. This work includes clearing of route from bushes etc, covering of cable laid in trench by loose soil for a 184 layer of 50mm thickness approximately before covering by bricks. The work shall be done as per the extant practice on North Western Railway and instructions of Railway Engineer at site. In case 1.2m depth of trench is not achievable due to site conditions, specific approval of JA grade officer will be required for each site where trench depth of 1.2m is not possible. Without the approval of JA Grade officer, no payment for trenching will be made for trench depth less than 1.2m. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution( Unit is Cubic Meter)

Digging of cable trench 0.3 Mtrs. Deep and 0.3 Mtrs. Wide on Asphalted Platform / Road / Hard rocky area. Refilling with earth leveling of trenches & restoring the original surface of trenches.The sharp edges will be smoothened out in bottom of the chase and will be leveled properly. In hard rocky ground area , cables will be laid normally on layer of shifted earth of 0.05 mtrs thickness previously deposited at bottom of the trench and cables will be covered with layer of sand or shifted earth of 0.1 mtr thickness. In case sharp edges of rocky ground can not be protected 185 from shifted earth then GI/ CI /PVC /DWC/ HDPE pipes will be used, if numbers of cables is small.In case number of cables are large RCC duct will be used. In isolated cases, it can be given smooth surface by using either masonry bricks or cement concrete. A row of bricks shall then be placed length wise on the top and jointed with cement mortar and layer of concrete with cement plaster shall be provided on top of the same. Note: This item in hard rocky area will be operated only where normal depth i.e.l.2 mtr is not possible and it will be decided by site engineer/unit officer incharge of work. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution( Unit is Cubic Meter)

Digging of cable pit (min 2x2x1m) as per instruction of Site Engineer, supplying and 186 filling of sand before and after coiling the cables, covering top of the cable pit with stones and providing brick masonry on all four sides of the cable pit and plastering thereafter. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

Laying of S&T Cables of various cores/ pairs/ quads in trenches/ GI pipes/ RCC pipes/ DWC pipes/ Trunking. This also includes laying of cables in track crossings & road crossings. Item includes provision of labels of coloured plastic adhesive tapes or any other identifiable material on 187 each cable to give the cable number at each Gantry Post/hectometer post.(Cables will be meggered before and after its laying by contractor under supervision of Railway Representative and he will submit the meggering report of each testing). Length of the cable laid includes the length of the cable coiled for termination purposes. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution(unit is RM running meter)

Cement concrete work for miscellaneous items in the ratio 1 : 3 : 6 . Item includes 188 excavation, ramming, curing and plastering with cement & sand mixture (aggregate not exceeding 3.8 cm.) (Aggregate cement & sand to be supplied by the contractor). Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution(Unit is cubic meter)

Providing brick masonry in ratio 1:6 cement and mortar including plastering with 1:4 189 cement and sand mixture both sides, 20 mm thick each with contractor's owned class II bricks, including excavation, curing, grouting, bolting etc. wherever required. Bricks sand and cement to be supplied by the contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution(Unit is cubic meter)

Supply of Earth Leakage Detector (ELD) 12 Channels as per RDSO Specn.RDSO/SPN/256/2002 or latest. Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Wiring, installation, testing and commissioning of Earth Leakage Detector (ELD) 12 Channels as per RDSO Specn.RDSO/SPN/256/2002 or latest. This includes supply of fuse terminal strip for incoming power supply wires. On job training at site will be given by OEM engineer for installation and maintenance of ELD. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after commissioning.

Supply of basic material to construct unit maintenance free earth as per RDSO Specs. No RDSO/SPN/197/2008 or latest and conforming to RDSO Drg.No.SDO/ RDSO/E&B/001 dtd.19.09.08 . It consist of following: (a) Copper bonded steel electrode of 3.0 m long, 17.2 mm dia with copper bonding thickness of minimum macrons and UL listed and marked = 1 no. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. © Copper strip of 150x25x6 mm, to 192 terminate earth rod = 1 no. (d) Copper strip of 300x25x6 mm (MEEB) = 1 no. (e) Copper strip of 150x25x6mm (SEEB) = 1 no. (ii) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate.(minimum 10 meter) (iii) Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter ) (iv) Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting various equipments to SEEB (v) Supply of copper lug sleeve for 3/16 cable Inspection: RDSO Inspection Charges:Borne by Railways Payment Terms: 100% after Supply.

Installation of Unit Maintenance Free Earth as supplied under item no. 13.3 of Chapter 13 of SOR . It includes ( i ) Digging the earth to the required depth. (ii) Insertion of electrode. (iii) Filling of earth enhancing compound (Approx.30 Kg) (iv) Provision of exothermic weld connections to copper tape of 25 mm x 6 mm x 150 mm to the earth electrodes. All material tools and features required for weld will be arranged by contractor. (v) This also includes CC cover 1.5 ft x 1.5 ft. 1 ft wall thickness 2 inch with cover 3 inch thickness. Cables 35 Sq mm/ 16 Sq mm/10 sq mm for connecting earth to busbar, busbar to busbar and busbars to various equipments. Earth electrode of 17.20 mm dia and 3.00 meter long high tensile low carbon steel circular rods 193 molecularly bonded with copper and outer surface (minimum copper bonding thickness of 250 micrones to made requirement of under writer's laboratories (UL) 467-2007 or latest. Copper strips of 150 mm x 25 mm x 6 mm to be welded with each earth electrode, copper strips of 300 mm x 25 mm x 6 mm for main equip- potential busbar, copper strips of 150 mm x 25 mm x 6 mm sub equip- potential busbar in relay room, power room and panel room. GI strip 25 mm x 2 mm for ring formation of earth pits Earth enhancement material in bags for each Earth Electrode. Inspection chamber of site 300 mm x 300 mm x 300 mm (Inside dimension) of approximate 50 mm thick with pulling hooks to cover the earth pits. Note: The installation of this item shall be carried out by the contractor as per RDSO Specn.No.RDSO/SPN/ 197/2008 or latest and conforming to RDSO Drg.No.S DO/RDSO/E&B/001 or latest. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after execution and testing.

Provision of Ring Earth for EI system which includes supply of all componenents of earthing & bonding system like earth electrode, earth enhancement material, earth pit, equi- potential earth busbar, connecting cables and tape/strips and other associated accessories in accordance with RDSO Spec.No.RDSO/SPN /197/2008 or latest consisting minimum 8 Nos. of earth pits connected in a ring to achieve less than 1 Ohms earth resistance for connecting EI equipments, relay racks, panel, power equipments as per Signal Engineering Practice. Diagram of ring earth should be supplied to Railway for Approval before execution. All related material as recommended by RDSO in Specn. No.RDSO/SPN /197/2008 or latest, will be supplied by the contractor. basic material for one earth pit is given below: (a) Copper bonded steel electrode of 3.0 m long, 17.2 mm 194 dia with copper bonding thickness of minimum macrons and UL listed and marked = 1 no. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 nos. © Copper strip of 150x25x6 mm, to terminate earth rod = 1 no. (d) Copper strip of 300x25x6 mm (MEEB) = 1 no. (e) Copper strip of 150x25x6mm (SEEB) = 1 no. (f) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate.(minimum 10 meter) (g) Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter ) (h) Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting various equipments to SEEB (i) Supply of copper lug sleeve for 3/16 cable Note:Earthing arrangement for EI must be as per RDSO guidelines issued by RDSO vide RDSO TAN no. STS/E//TAN/3006 dated 02.11.2012 or latest. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Installation, testing and commissioning of Ring Earth for EI system which includes installation of all components of earthing & bonding system like earth electrode, earth enhancement material, earth pit, equi- potential earth busbar, connecting cables and tape/strips and other associated accessories in accordance with RDSO Spec.No.RDSO/SPN /197/2008 or latest consisting minimum 8 Nos. of earth pits connected in a ring to achieve less than 1 Ohms earth resistance for connecting EI equipments, relay racks, panel, power equipments as per Signal Engineering Practice. Diagram of ring earth should be supplied to Railway for Approval before execution. Installation of 195 one earth pit includes ( i ) Digging the earth to the required depth. (ii) Insertion of electrode. (iii) Filling of earth enhancing compound (Approx.30 Kg) (iv) Provision of exothermic weld connections to copper tape of 25 mm x 6 mm x 150 mm to the earth electrodes. All material tools and features required for weld will be arranged by contractor. (v) This also includes CC cover 1.5 ft x 1.5 ft. 1 ft wall thickness 2 inch with cover 3 inch thickness. Cables 35 Sq mm/ 16 Sq mm/10 sq mm for connecting earth to busbar, busbar to busbar and busbars to various equipments. Earth electrode of 17.20 mm dia and 3.00 meter long high tensile low carbon steel circular rods molecularly bonded with copper and outer surface (minimum copper bonding thickness of 250 microns to made requirement of under writer's laboratories (UL) 467-2007 or latest. Copper strips of 150 mm x 25 mm x 6 mm to be welded with each earth electrode, copper strips of 300 mm x 25 mm x 6 mm for main equip- potential busbar, copper strips of 150 mm x 25 mm x 6 mm sub equip-potential busbar in relay room, power room and panel room. GI strip 25 mm x 2 mm for ring formation of earth pits Earth enhancement material in bags for each Earth Electrode. Inspection chamber of site 300 mm x 300 mm x 300 mm (Inside dimension) of approximate 50 mm thick with pulling hooks to cover the earth pits. Note:Earthing arrangement for EI must be as per RDSO guidelines issued by RDSO vide RDSO TAN no. STS/E//TAN/3006 dated 02.11.2012 or latest. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after commissioning.

Supply of Digital Multimeter of Fluke 287 Industrial or superior True RMS with 196 temperature, Analog bar graph, Digital display, Backlight, 1000V AC/DC, measure up to 10A, 20A for up to 30 second . Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Professional AC/DC clamp meter 3 ¾ digit , true RMS measurement, For 197 Measurement of DC/AC currents up to 1000A, Voltage up to 600V, resistance up to 40 M and frequency up to 1 MHz with set of leads & carrying case. Model - DCM 39A or equivalent/ higher make Motwane/Stanlay/Fluke/Megger Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Handheld Digital Earth Clamp Tester for clamp on earth/ground resistance 198 measurement up to 1000 ohms. Accuracy 0.1 - 0.99 : 1%, 1 - 49 : 1.5% Also measure current leakage up to 20A. No spines required for measurement Model - DECT-2 or equivalent / higher version make Motwane/Stanlay/Fluke/Megger. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of electronic Cable route tracer/locator with underground cable and pipe 199 locating receiver and cable avoidance tool that provide location of armoured OFC , signalling and telecom , power cable etc. make : C Scope Stanley/3M Dynatel , model: DXL-4 DBG /2273M-iD 30 or superior. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Road Measuring Cycle, made of Aluminum with 05 digit counter, foldable with bag. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Digital Cable Insulation Tester for measurement of cable insulation resistance with auto range 0-500 V DC. Motwani or from any reputed make. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Transmission Measuring Set/Kit along with all accessories as per RDSO Specn.No.IRS: TC- 43/87 or latest. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Cable Fault Locater to localize the faults of underground cables. Aplab 203 make (Model No.3049) OR C Scope Stanley make( Model TS-90) or superior from any reputed make. It also includes supply of all accessories required to localize faults of underground cables. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of Digital Earth Resistance Tester for measurement of earth resistance with 3.5 digital LCD, 12.5 mm screen segment and Range -0.5 Ohms to 500 Ohms. WACO or from any repudiated make. Inspection: Consignee Inspection Charges:None Payment Terms: 100% after Supply.

Supply of seal plier as per sample got approved from site engineer incharge. Inspection:Consignee Inspection Charges: None Payment Terms: 100% after Supply

Supply of Vacuum Cleaner, Eureka Forbes or from any reputed make only as per specification given below:-Voltage-230V AC,50Hz, Input Power(IEC)-1000 Watt, Suction of the motor 206 1700 mm of water column , Airflow-30 litres/second, Dust collection capacity-61(dry), 81(wet), Variable power option-2 Speed, Blower function, Air filtraction-2 Stage, Hepa filter, Dust collection type-Washable dust bag, On board accessory storage. Inspection:Consignee Inspection Charges: None Payment Terms: 100% after Supply

Supply of Safety lock Godrej or Navtal make size as approved by site engineer. Inspection:Consignee Inspection Charges: None Payment Terms: 100% after Supply

Supply of hand cuff lock Godrej or Navtal make size as approved by site engineer. Inspection:Consignee Inspection Charges: None Payment Terms: 100% after Supply

Supply of Obstruction test piece 3mm/5mm as per sample approved by Engineer incharge. Inspection:Consignee Inspection Charges: None Payment Terms: 100% after Supply

Provision of Power supply arrangement, with contractors own Generating sets , 210 capacity 5 KVA or above as per requirement of Station Signalling load, for testing of Signalling system in the case of irregular Local power supply / under capacity AT,s supply system at station. Inspection:Consignee Inspection Charges: None Payment Terms: 100% after Execution(Unit is per DG set per day)

Complete painting and varnishing work at a station (3/4 Line). This includes painting of signal posts and fittings, apparatus cases, point machines, junction boxes, rail post etc. This also includes varnishing, letter writing on relays, terminal Nos., apparatus cases, point machine, Signal Nos. and other details as per Signal Engineering Manual and instructions of Engineer at site. The item includes painting of distances of main cable run from G.P nearest to cable run and painting of 211 distances of signals from nearest line on the signals base. At least two coats of paint is to be applied besides primary coating of red oxide. This includes supply of paints, varnishes and all other material required for complete painting work at a station. This includes painting on existing functional units also. The painting shall consist of initial red oxide / base paint followed by at least two coat of the paint as per standard painting scheme. This item also includes painting of interlocked gate attached to the station. Location box no. shall be painted on both sides. Inspection:Consignee Inspection Charges: None Payment Terms: 100% after Execution

Hiring of JCB machine(in good condition) for levelling and dressing ground/ dismantling structures including disposal of debris through dumpers etc with contractors labour , JCB 212 machine , machine operator, fuel etc. The contractor shall arrange for road permit for all the states for operation as per instructions of engineer incharge and vehicle shall not be more than 3 years old . Payment shall be made for actual working hrs at site. Inspection:Consignee Inspection Charges: None Payment Terms: 100% after Execution

Installation, wiring, testing and commissioning of Diesel Generator Set 20 KVA, Single Phase, 240V, 1500 RPM, 50 Hz, 30 BHP (minimum) mounted with air cooled double cylinder diesel engine with acoustic enclosure complete silent type DG sets confirming to RDSO Specn.No.IRS(S) 69/86 with latest. (CPCB Noise and Emission Complaint) Kirloskar make engine/alternator.This also 213 includes supply of standard AMF control panel, supply of 12V/120 AH battery set along with battery charger of suitable rating for charging the batteries to ensure self starting arrangement of DG sets. It also includes supply of start/stop buttons, Volt/Ampere/Frequency meters and 63 AMP MCB(minimum). Note: DG set will be procured from OEM or authorized dealer of OEM's with the warranty certificate of minimum 1 year. All masonry work required for installation of DG set will be done by contractor under supervision/instructions issued by site engineer incharge. Inspection: Consignee Inspection Charges: None Payment Terms: 100% after Commissioning

Supply & fixing of Crank Handle Box & SM's key box of size 450 mm x 250 mm x150 mm and made of 12 mm thick teakwood with a glass front, lock and sealing arrangement. All material like lock, teakwood, handles, hinges, glass sheet of 3 mm thick will be supplied by the contractor. Box will be polished and description will be written as per instructions of Engineer in charge. Inspection:Consignee Inspection Charges: None Payment Terms: 100 % after Execution

Supply & fixing of KLCR boxes & fixing of KLCR Relays in ASM office. It includes supply of any minor bracket, nuts, bolts, teakwood, sun mica, lock, drilling hole etc as directed by engineer 215 at site. It also includes supply and wiring of push buttons along with LEDs for KLCR circuit. Rly will supply only KLCR relays and contractor has to wire KLCR relays. It includes supply of all the related wiring material. Inspection:Consignee Inspection Charges: None Payment Terms: 100 % after Execution

Supply of UTP CAT-6 cable in a roll of 305 meter and make Siemen/ Systemax / Panduit/ Tyco/ Krone/ AMP. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply of 4/2 wire combined Portable Light Weight Emergency control telephones of metal body with 6-pin plug as per IRS-TC-75/99 (Amnd 4) or latest. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Supply of KRONE Punching tool, Krone or any reputed make only. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Supply of patch chord cable (10 meter long) with FC/PC connectors compatible with SDH equipments as per TEC Specn.No.GR/OFJ-02/01 May 2004 with latest Amendment. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Supply, preparation, splicing and installation of straight joint for 24 fibers along with 220 enclosures with heat shrinkable splice protection sleeve as per TEC Specn.G/OJC-02/01 March- 99 or latest. Splice losses in no case should be more than 0.1 dB. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution

Supply of managed SDH (STM-1 Add/Drop MUX and upgradeable to STM-4) fully wired for 2 X 63 MB and equipped for 21E1s and a Virtual Container (VC)-12 with STM-1(L1.1) aggregate interface including power supply, order wire, Ethernet card, sub rack, inbuilt DDF, installation material and all other accessories, manuals etc. as per TEC. Specification GR SDH 04/02, March 02 or with latest amendment. The contractor will supply all other accessories as mentioned in the above said TEC Specifications and system will have provision of different redundancy cards as per the TEC 221 Specifications. Note: It shall be possible to increase capacity from 21E1 to 63 E1s by adding / inserting tributary cards. This includes connecting all pig tails, optical patch cords etc. to the SDH equipment. This also includes connecting the SDH equipment with all cards to the 48V Bus including supply of wires and connectors. Termination of all E1s on DDF taking PVC cable over runway or a wall. At the terminal station, one port may be disabled if required as per instructions given by site engineer incharge. Inspection:(i) RDSO if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply.

Installation, wiring, testing & commissioning of managed SDH (STM-1 Add/Drop MUX and upgradeable to STM-4) fully wired for 2 X 63 MB and equipped for 21E1s and a Virtual Container (VC)-12 with STM-1(L1.1) aggregate interface including power supply, order wire, Ethernet card, sub rack, inbuilt DDF, installation material and all other accessories, manuals etc. as per TEC. Specification GR SDH 04/02, March 02 or with latest amendment. The contractor will install all other 222 accessories as mentioned in the above said TEC Specifications and system will have provision of different redundancy cards as per the TEC Specifications. Note: It shall be possible to increase capacity from 21E1 to 63 E1s by adding / inserting tributary cards. This includes connecting all pig tails, optical patch cords etc. to the SDH equipment. This also includes connecting the SDH equipment with all cards to the 48V Bus including supply of wires and connectors. Termination of all E1s on DDF taking PVC cable over runway or a wall. At the terminal station, one port may be disabled if required as per instructions given by site engineer incharge. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning.

Supply of 2 Mb Programmable Primary Digital drop insert multiplexer as per RDSO Specs. IRS TC- 68/2004 (Amnd.1) or latest with conference facility and other stipulation to tender documents and fully wired for 30 channel complete with power supply card, remote control, supervision facility and all other accessories, installation material, manuals etc. It should have facilities to accommodate data interface card in multi drop mode and should be able to support cards needed for video conferencing and ISDN. It shall support NMS installed at Test Room and may 223 operate local/remote location of entire section. It also includes submission of all technical documents, manuals and supply of all miscellaneous items which will be required for final testing and commissioning of system. The above MUX should be equipped with following circuits: - i) 2 wire/ 4 wire E&M VF circuits ( minimum 16 nos ckts) ii) Subscriber loop circuits ( minimum 4 nos ckts) iii) Exchange loop interface circuits (minimum 8 circuits ) iv) This also includes connecting all pigtails, optical patch cords etc to the SDH equipments. This also includes connection of SDH and primary MUX equipment with all interface cards to the 48V Bus including supply of wires and connectors termination of all evens on DDF taking PVC cable over runway or a wall and termination of VF interface circuit to the Krone type. Inspection:(i) RDSO if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply

Installation, wiring, testing and commissioning of 2 Mb Programmable Primary Digital drop insert multiplexer as per RDSO Specs. IRS TC- 68/2004 (Amnd.1) or latest with conference facility and other stipulation to tender documents and fully wired for 30 channel complete with power supply card, remote control, supervision facility and all other accessories, installation material, manuals etc. It should have facilities to accommodate data interface card in multi drop mode and should be able to support cards needed for video conferencing and ISDN. It shall support NMS installed at Test Room and may operate local/remote location of entire section. It also includes 224 submission of all technical documents, manuals and supply of all miscellaneous items which will be required for final testing and commissioning of system. The above MUX should be equipped with following circuits: - i) 2 wire/ 4 wire E&M VF circuits ( minimum 16 nos ckts) ii) Subscriber loop circuits ( minimum 4 nos ckts) iii) Exchange loop interface circuits (minimum 8 circuits ) iv) This also includes connecting all pigtails, optical patch cords etc to the SDH equipments. This also includes connection of SDH and primary MUX equipment with all interface cards to the 48V Bus including supply of wires and connectors termination of all evens on DDF taking PVC cable over runway or a wall and termination of VF interface circuit to the Krone type. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Commissioning.

Supply of Pre-lubricated HDPE duct, 40 mm OD, 33 ID as per RDSO specification No. RDSO/SPN/TC/45/2013 Rev. 2.0 or latest. The item also includes supply of all the accessories of HDPE 225 duct like end caps, collars, bends, couplers etc. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Laying of Pre-lubricated HDPE duct, 40 mm OD, 33 ID as per RDSO specification No. 226 RDSO/SPN/TC/45/2013 Rev. 2.0 or latest. The item also includes installation of all the accessories of HDPE duct like end caps, collars, bends, couplers etc. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Blowing/drawing of OFC cables in the HDPE duct along with all the protective work as per instructions of engineer incharge at site. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Construction of brick chamber of optical fibre cable straight through joint as per Drg. 228 No. CSTE/NWR/ SOR/23. It also includes supply and provision of all the material required for this item like bricks, sand, cement etc. The cement and sand should be in ratio 1:6. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Supply of SMPS based Battery Chargers as per RDSO Spec for Telecom use 48 volts, 25 Amps in 2+1 configuration modules of 25 Amps with ultimate expandable capacity 50 Amps, 229 automatic switching between the modules as per RDSO Spec No. RDSO/SPN/TC/23/1999 version 4 or latest along with two potential free contacts. Inspection: (i) RDSO if value of item in work more than 5 lakhs (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs as per extant instructions by Railway Board. Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% on Supply

Supply of 48Volt/200AH maintenance free VRLA Batteries duly charged as per IRS Spec. No. S-93/96(A) with amendments-1 or latest Inspection: RDSO Inspection Charges: Borne by Railways. Payment Terms: 100% after Supply.

Installation, wiring, testing & commissioning of 48Volt/200AH maintenance free VRLA Batteries duly charged as per IRS Spec. No. S-93/96(A) with amendments-1 or latest. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Supply of Universal 2/4 wire way station control Telephone with PSU as per RDSO spec. no. IRS: TC:82: 2005) (with Amd. 1 or latest) Inspection: RDSO Inspection Charges: Borne by Railways Payment Terms: 100% after Supply."

Video recording of trenching. It includes the man power and all required arrangement for video recording at site. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Execution.

Supply of 10 Pairs Krone type D.P. box as per Tech spec, make Hensel or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Fixing and wiring of 10 Pairs Krone type D.P. box as per Tech spec, make Hensel or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of 20 Pairs Krone type D.P. box as per Tech spec, make Hensel or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Fixing and wiring of 20 Pairs Krone type D.P. box as per Tech spec, make Hensel or superior. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of 19" covered rack of size 2035 X 600 X 600 mm (Approx) as per 238 Drg.No.CSTE NWR SOR 24. The rake shall be complete with all fittings for housing SDH equipments, PDMUX, DDF, MDF using krone modules and other accessories like cable and connectors, runway ladders, locking arrangement, completely wired and equipped with IPM for all equipped channels. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Installation and complete indoor wiring of 19" covered rack of size 2035 X 600 X 600 mm (Approx) as per Drg.No.CSTE NWR SOR 24. The rake shall be complete with all fittings for 239 housing SDH equipments, PDMUX, DDF, MDF using krone modules and other accessories like cable and connectors, runway ladders, locking arrangement, completely wired and equipped with IPM for all equipped channels. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of integrated Access Multiplexer 4U height/19" Rack mountable with 4 DTE 240 (1+1) protection E1 interfaces & V.21/V.23 Modules supporting 8 Interface of (2W/4W) in one module and one Telnet port balance 2 slots empty; unit to support both AC/DC power supply; Cable to be provided for one no for E&M interface; DC to AC adapter- 1 Nos; Make Fabio 4C/ 4E1/ DC Team Engineer. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.

Installation of integrated Access Multiplexer 4U height/19" Rack mountable with 4 241 DTE (1+1) protection E1 interfaces & V.21/V.23 Modules supporting 8 Interface of (2W/4W) in one module and one Telnet port balance 2 slots empty; unit to support both AC/DC power supply; Cable to be provided for one no for E&M interface; DC to AC adapter- 1 Nos; Make Fabio 4C/ 4E1/ DC Team Engineer. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of Electronic LC gate telephone system in 1+6 configuration with inbuilt voice recorder . It includes supply of 'surge protection and line connection unit /circuit' and centralised 242 power supply system with battery as per RDSO Spec no. RDSO/SPN/TC/51/2011Revision 3.0 amendment 1.0 or latest. Inspection: (i) RDSO/RITES if value of item in work more than 5 lakhs or as per extant policy (ii) Consignee subject to procurement from RDSO approved vendors if value of whole item in work less than 5 lakhs or as per extant policy Inspection Charges: (i)Borne by Railways (ii) None Payment Terms: 100% after Supply

Supply and provision of thermo-shrink splice filling jelly jointing kit as per RDSO Specn.No.RDSO/SPN/TC/57 2015 (Rev.1) Amnd.1 or latest suitable for PIJF cable for straight through joints. It includes supply of all the accessories as recommended by RDSO. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after Supply.

Painting of emergency post and sockets in sections as per instructions of the site 244 engineer in charge. This shall include all material, labour and transportation required for painting of emergency post and sockets in section. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Shifting and installation of control and other telecom equipments like control phone, 245 magneto phone, auto phone, VHF sets, VF Repeaters etc from old station building to new station building as per instructions of site engineer. All the material required for fixing and installation will be supplied by the contractor. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after execution.

Supply of Sine Wave output Voltage inverter of 2.0KVA capacity with minimum 180 Minutes backup, with having battery capacity VAH:8640 with trolley stand. Inspection: Consignee Inspection Charges: None. Payment Terms: 100% after supply.