REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT INFRASTRUCTURE REFUSE TRNSFER STATION FOR MUNNICIPAL CORPORATION JUNAGADH

No. Description Quantity RATE Unit Amount

1 Excavation for foundation upto 1.5m depth including sorting

out and stacking of useful materials and disposing off the

excavated stuff upto 50Meter lead. (C) Hard Murrum

2 Box Cutting the road surface to proper slope and camber for

making a base for road work including removing the excavated

stuff and depositing on the road side slope as directed up to

3 Providing and laying cement concrete 1:3:6 (1-Cement : 3-

coarse sand : 6- hand broken stone aggregates 40mm nominal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth

4 Providing and laying controlled cement concrete M-250 for

RCC works including the cost machine mixing, vibrating,

scaffolding, incl. cost of form work / shuttering but excluding 98.76 4803.12 Cu.M. ₹

cost of reinforcement etc. complete up to plinth level for RCC

5 Providing and laying controlled cement concrete M-250 for

RCC works including the cost machine mixing, vibrating,

scaffolding, incl. cost of form work / shuttering but excluding 4.86 7939.24 Cu.M. ₹

cost of reinforcement etc. complete for RCC COLUMN

6 Providing and laying controlled cement concrete M-250 for

RCC works including the cost machine mixing, vibrating,

scaffolding, incl. cost of form work / shuttering but excluding 25.65 6388.41 Cu.M. ₹

cost of reinforcement etc. complete for BEAMS

7 Filling available excavated earth (excluding rock) in trenches

plinth, sides of foundations etc. in layers not exceeding 20cm.

In depth consolidating each disposited layer by 116.63 136.92 Cu.M. ₹

ramming and watering.

8 Carring out plinth treatment to post construction / existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with I.S.I

specification. Using Chlordene and Chiorpurfiles 20 EC. As

Per 6131_paret-II Consentration Weight one percent is 375.00 59.46 Smt. ₹

recommended i.e one litre 20 EC chemical emulsion with

liter give 1 % concrentration inclusive of one litre chemical

emulsion appication at the rate of 5 Litre chemical / Sqm of

surface is recommended as per I.S

9 Filling in plinth with sand under floors including watering

ramming, consolidating and dressing complete

10 Brickwork using common burnt clay building bricks having

crushing strength not less than 35kg./Sq.Cm. in Foundation

and Plinth in Cement Mortar 1:6 (1-Cement : 6 -fine sand) 25.12 4214.33 Cu.M. ₹

(B) Conventional

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

11 Vacuum Dewatered Flooring (VDF) consists of providing and

laying high-performance concrete flooring using a vacuum

dewatering process to remove excess water from freshly laid

concrete, resulting in a dense, durable, abrasion-resistant, and

smooth surface ideal for industrial floors, warehouses, parking

areas, and other heavy-traffic zones. The work includes surface

preparation, placement of specified-grade concrete, vibration,

application of vacuum dewatering through pumps and filter 375.00 869.61 Smt. ₹

mats, and finishing with power floats and trowels. VDF offers

superior strength, higher surface density, reduced cracking,

faster usability, and long service life; however, it involves

higher initial costs, requires skilled manpower, depends on

specialized equipment, and is primarily suitable for horizontal

12 Providing TMT Bar FE500D reinforcement for R.C.C. work

including bending, binding and placing in position complete

floor two level

13 20mm thick sand faced cement plaster on walls upto height

10metres above ground level consisting of 12mm thick

backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick 288.00 342.41 Smt. ₹

finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

14 Providing and fixing M.S. grills of required pattern to wooden

frames of windows etc. with M.S. flats at required spacings

and frame alround, square or round bars with round headed 1080.24 106.23 kg ₹

bolts and nuts or by screws

(A) Plain Grill.

15 Steel work, welded in built up sections framed work including

cutting, hoisting, fixing in position and applying a priming

coat of red lead paint. (A)In beams and joists, channels angles

Tees, flats, with connecting plates or angle cleats as in main 160.93 9108.48 Qtl. ₹

and cross beams. Hip and jack rafters, purlins conneted to

rafters and the like

16 Providing and fixing PUF insulated continueous sandwich

panels for walls of total thickness not less than 50 mm and

width 1.0 m made out from continue line method on automatic

plant. Shall have 0.5 mm thick pre coated GI Sheet on both

side of Polyurethane foam conforming to IS 12436 :1988. The

Procoated sheet shall be of minimum 240 mpa steel grade

conforming to IS 14246 :1995 and shall have zinc coating of

minimum 120gsm as per IS 277 : 1992 , 5-7 microns epoxy

primer on both side of the sheet and polyester top coat 15-18 476.00 3146.70 SQ.MT ₹

micron. The PPGI sheet shall have plastic protective guard film

of minimum 25 mocrons to avoid scratches during film

transportations. .the panels shall be vertically joined together

by tongue and groove joints. The PU foam shall be self

extinguishing fire retardant type having minimum density of

40 kg/cumt ( + , 2. kgs. ) including 0.25 mm thick craft paper

edging on both edges. The panels shall be fixed to the steel

frame structure with minimum 5 mm thick self tapping

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

17 Providing and fixing of end cap of roofing panel. The end cap

track shall be mace out of 0.5 mm thick pre coated GI sheet

suitable for 30 mm thick panel. The Precoated sheet shall be of

minimum 240 mpa steel grade conforming to IS 14246:

and shall have zinc coating of minimum 120 gsm as per IS

277:1992 , 5-7 microns epoxy primer on both side of the sheet 90.00 796.73 Rmt ₹

and polyster top coat 15-18 micron. the PPGI sheet shall have

plastic protective guard film of minimum 25 microns to avoid

scratches during transportations. The U track shall be fixed

with suitable POP rivet with wall and roof panels with suitable

POP rivet with wall and proof panels

18 Finishing wall with water proofing cement paint of on wall

surfaces (Two coats) to give an approved brand and

manufacture and of required shape even shade after thoroughly 288.00 60.31 Sqmt ₹

brushing the surface to remove all dirt and remains of loose

powered materials.

19 Wall painting (two coats) with plastic emulsion paint

ofapproved brand and manufacture on undecorated wallsurface

to give an even shade including throughly brushing the surface 288.00 82.85 Sqmt ₹

free from mortar droppings and other foreign matter and sand

papered smooth.

20 Applying priming coat over new steel and other metel surface

after and including preparing the surface by throughly

cleaning, oil,grease, dirt and other foreign matter and scoured

with brushes fine steel wood, scrapers and sand paper with

ready mixed priming paint

brushing red lead.

21 Painting two coats (excluding priming coat) on new steel and

other metal surface with enamel paint, brushing, interior to

give an even shade including cleaning the surface an even

shade including cleanicn the surface of all dirt, dust and other

22 Excavation for foundation including all safety provision using

site rails and stacking excavated stuff up to a lead of 90 mtr.

Cleaning the site etc. Completed.

In all sorts of soil and soft murrum

23 Providing and laying cement concrete 1:3:6 (M10) (1 Cement :

3 Coarse sand : 6 Hand Broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of formwork

in Foundation and Plinth

24 Providing and laying controlled cement concrete M.200 and

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (upto 10 ton)

a) For Footings

b) For Columns 6.52 4749.43 cum ₹

c) For Ground Beam 5.78 4644.03 cum ₹

d) For Coping at Top of Wall 1.93 4644.03 cum ₹

25 Providing TMT Bar FE 415 reinforcement for R.C.C. work

including bending, binding and placing in position complete 1045.20 77.29 Kg ₹

upto floor two level (more than 10 ton)

26 Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:6 (1‐ Cement : 6 ‐fine sand)(B) 38.51 4214.33 cum ₹

Conventional (upto 10 ton) extra for brickwork in

superstructure above floor to level

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

27 20 mm thick sand faced cement plaster on walls upto height

1.5 metres above ground level consisting of 12 mm thick

backing coat of C.M. 1:3 (1 cement : 3 sand ) and 8 mm thick 389.50 342.41 Sqmt ₹

finishing coat of C.M. 1:1 (1Cement : 1 Sand ) etc. complete.

28 Refilling including ramming, watering, consolidating disposal

of surplus stuff as directed within a radius of 3 kms 48.34 27.60 cum ₹

29 Finishing wall with water proofing cement paint of on wall

surfaces (Two coats) to give an approved brand and

manufacture and of required shape even shade after

thoroughly brushing the surface to remove all dirt and remains 389.50 66.99 Sqmt ₹

of loose powered materials. & Extra for every subsequent coat

of finishing with cement paint on ceiling and sloping

30 Providing and fixing 1.20 Metre high fencing with 2.0 Metre

long M.S. Angle posts 40mm x 40 mm x6 mm and oil painting

3 coats fixed at 2.5 Mt,C/c. with five Horizontan lines and two

diagonals of galvanised steel barbed wire weighting 9.38 Kg. 230.00 391.93 Rmt ₹

per 100 Metre, strained and fixed to posts with G.I,staples

including fixing the postsin ground with 0.5 M x 0.5.M x

M. block in C.C1:5:10 etc complete.

31 Demolition of Brick work and stone masonry including

stacking of serviceable materilas and disposal of unserviceable

materials with all lead and lift.(ii) In Cement Mortar.

32 Clearing and grubbing road land including uprooting rank

vegetation grass bushes,shrubs,sapling and trees girth upto

mm removal of stumps of trees cut earlier and disposal of 0.13 84255.99 Ha ₹

unserviceable materials(A) By manual means in area of light

33 Excavation for foundation upto 1.5 m depth including sorting

out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead.(A) Loose or soft soil

34 Supplying of graded stone aggregate of following sizes (for

W.B.M. Road)(2) Hand broken stone aggregate 40 mm to 63 195.30 306.78 cum ₹

35 Filling in foundation and plinth with murrum or

selected soil in layers of 20cm. thickness including 195.30 301.78 cum ₹

watering, ramming and consolidating etc. complete.

36 Spreading the stone aggregate for rolling and W.B.M.

including filling the interstices to required camber and gradient

(excluding spreading of Blindage)(ii) 40mm to 63mm size

aggreagates (H.B.)

37 Rolling and consolidation of W.B.M including filling

indepression which occur during the process, with power roller 195.30 22.75 sqm ₹

8 tonne to 12 tonne.

38 Providing and laying cement concrete 1:3:6 (1‐Cement : 3‐

coarse sand : 6‐ hand broken stone aggregates 40 mm nominal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth (upto 10 ton)

39 Providing and laying controlled cement concrete M.200 and

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work (A) Foundations, 156.24 4118.65 cum ₹

footings, Base of columns and Mass concrete

40 Providing and placing in position FE 500D bar reinforcement

for following items including cutting bending hooking and

tying complete as per detailed drawing.For well :- curb,

staining, cap and RCC Raft.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

41 Excavation for foundation for loose and soft soil including

sorting out and stacking of useful materials and disposing of

the excavated stuff up to 50 meter lead. a) From 0.0 to 1.5 m.

42 Filling with available excavated earth (excluding rock) in

trenches, plinth, sides of foundation in layers not exceeding

cm in depth consolidating each deposited layer by ramming

43 Providing and laying cement concrete 1:3:6 (1- Cement : 3-

coarse sand : 6- hand broken stone aggregates 40 mmnominal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth

44 Providing and laying controlled cement concrete M-250 for

RCC works including the cost machine mixing, vibrating,

scaffolding, incl. cost of form work (Ply wood only) / 2.18 4803.12 cum ₹

shuttering but excluding cost of reinforcement etc. complete up

to plinth level for RCC FOOTING

45 Providing and laying controlled cement concrete M-250 for

RCC works including the cost machine mixing, vibrating,

scaffolding, incl. cost of form work (Ply wood only) / 4.05 7939.24 cum ₹

shuttering but excluding cost of reinforcement etc. complete up

to floor 2 level for RCC COLUMN

46 Providing and laying controlled cement concrete M-250 for

RCC works including the cost machine mixing, vibrating,

scaffolding, incl. cost of form work (Ply wood only) / 5.83 6388.42 cum ₹

shuttering but excluding cost of reinforcement etc. complete up

to floor 2 level for BEAMS

47 Providing TMT Bar FE 500D reinforcement for R.C.C. work

including bending, binding and placing in position complete 1512.81 77.29 kg ₹

upto floor two leve (upto 10 ton)

48 20 mm thick sand faced cement plaster on walls upto height

metres above ground level consisting of 12mm thick backing

coat of C.M. 1:3 (1-cement : 3-sand) and 8 mm thick finishing 162.72 342.42 Sqmt ₹

coat of C.M. 1:1 (1-cement : 1 sand) etc. complete.

49 Finishing wall with weather proof exterior emulsion paint on

wall surface (two coats) to give an required shape even shade

after thoroughly brushing the surface to removal dirt, and

remains of loose powdered materials.etc complete

50 Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall surface

to give an even shade including throughly brushing the surface 162.72 82.86 Sqmt ₹

free from mortar droppings and other foreign matter and sand

papered smooth.

51 Providing and fixing M.S. grills of required pattern to wooden

frames of windows etc. with M.S. flats at required spacings

and frame alround, square or round bars with round headed

bolts and nuts or by screws (A) Plain Grill.

52 Applying priming coat of over new steel and other metal

surface after and including preparing the surface by thoroughly

cleaning, oil grease, dirt and other foreign mater and scoured

with brushes fine steel wool, scrapers and sand paper with

ready mixed priming paint brushing red lead.

53 Painting two coats (excluding priming coat) on new steel and

other metal surface with enamel paint, brusing interior to give

an even shade including cleaning the surface an even shade 126.00 92.21 smt ₹

including cleaning the surface of all dirt, dust and other foreign

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

54 Providing and fixing Village name boards as per standard

I.R.C. typedesign of steel plate including painting lettering etc.

complete with fixing in C.C. 1:4:8 block with necessary 64.00 3437.60 Each ₹

excavation.writing letter of figres on any surface with block

55 Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminium housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 4.00 3951.12 Nos ₹

lumens/watt . LED driver efficiency > 85 %.( fittings required

LM-79 & LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the

ranges shown.) (B) Flood Light (IP-65), Surge protection -

4KV integral and ,Light must have 440VAC line supply with

over-voltage protection. (iii) above 24 to 36 watts Cat-ll

including labour Cost.

56 Providing and fixing G.I. Rain water spout of 50mm dia. and

57 Anti-Termite System:Providing and laying of permanent piping

technology anti-termite treatment before flooring work by

installing LLDP (Low linear density polyethylene) tube of

mm O.D. & 6.4 mm 1.D. with inbuilt pressure compensation

chip every 30 cm interval in the tube, having working pressure

of 2 Kg/cm2 and release rate of 1.9 Itr/hour fixed by P-clips

and nails. The LLDP pipe shall be installed at the entire

periphery of the building and at internal network of building at

a depth of 20 to 200 mm under floor at every 2 to 3 mtr. c/c

distance (adjusted as per building layout ) & Ends of loop pass

through a PVC elbow of minimum 32 mm ID at junction box

of wall and floor level, entering into a steel reinforced grooved 9.00 134.33 smt ₹

flexible pipe of minimum 22 mm ID leading into junction box

and the loops shall terminate in junction boxes & test every

junction during injecting chemicals for termite control

treatment. The antitermite chemical Imidacloprid 30.5% SC

mix as per IS-6313 (part III) shall be injected by the pressure

pump diluted with water @ 10.5 ml/5 ltr of water at the rate of

2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall submit

approved line plan for piping system and junction boxes dully

approved by Engineer-in-Charge with bond of 5 year

warranty.(i)Anti Termite chemical injected area (Chemical

injecting incl. labour cost)

58 Excavation in all types of hard and soft soil such as murrum,

sand, clay, black cotton soil, kanker etc. and also in wet

condition if required removing, transporting and stacking of

useful materials and disposing off the excavated stuff with in

the estate lead.

From 0.0 to 1.5 m

59 Excavation in all types of hard and soft soil such as murrum,

sand, clay, black cotton soil, kanker etc. and also in wet

condition if required removing, transporting and stacking of

useful materials and disposing off the excavated stuff with in

the estate lead.

From 1.5 to 3.0 m

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

60 Filling available excavated earth (excluding rock) in

foundation & plinth in layers not exceeding 20 cm in depth

consolidating each deposited layer by ramming and watering.

61 Filling in plinth with sand under floors including watering

ramming, consolidating and dressing complete (upto 10 13.42 481.80 Cum ₹

62 Providing and laying cement concrete 1:3:6 (1- Cement : 4-

coarse sand : 6 stone aggregates 40 mm nominal size) and

curing complete excluding cost of formwork in (A) Foundation 5.65 3070.94 Cum ₹

and Plinth (upto 10 ton) A) FOR PLAIN CONCRETE

63 Providing and laying controlled cement concrete M-250 for

RCC works including the cost machine mixing, vibrating,

scaffolding, incl. cost of form work / shuttering but excluding 7.72 4676.06 Cum ₹

cost of reinforcement etc. complete up to plinth level for RCC

64 Providing and laying controlled cement concrete M-250 for

RCC works including the cost machine mixing, vibrating,

scaffolding, incl. cost of form work / shuttering but excluding 6.27 8579.76 Cum ₹

cost of reinforcement etc. complete up to floor 2 level for RCC

65 Providing and laying controlled cement concrete M-250 for

RCC works including the cost machine mixing, vibrating,

scaffolding, incl. cost of form work / shuttering but excluding 5.66 6805.96 Cum ₹

cost of reinforcement etc. complete up to floor 2 level for

66 Providing and laying controlled cement concrete M.250 and

curing complete including the cost of formwork but excluding

the cost of reinforcement for reinforced concrete work in RCC

67 Providing and laying controlled cement concrete M.250 and

curing complete including the cost of formwork but excluding

the cost of reinforcement for reinforced concrete work in RCC

68 Providing and laying controlled cement concrete M.250 and

curing complete including the cost of formwork but excluding

the cost of reinforcement for reinforced concrete work in RCC

69 Providing and laying controlled cement concrete M.250 and

curing complete including the cost of formwork but excluding

the cost of reinforcement for reinforced concrete work in RCC

70 Providing TMT Bar FE 500D reinforcement for R.C.C. work

including bending, binding and placing in position complete 3533.60 77.29 KG ₹

upto floor two level

71 Brick masonary in cement mortar (1:5) using common burnt

clay building bricks having crushing strength not less than

kg/cm2 including scaffolding, curing etc. complete for walls,

parapets, etc. at all levels.

72 Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of

6mm Mild steel round bars after every three course embedded 58.64 696.33 Sqm ₹

in Cement Mortar in foundation and plinth (B) Conventional

(upto 10 ton). in superstructure above plinth level upto all

73 Providing 10mm thick cement plaster in single coat on

brick/concrete walls for interior plastering upto floor two level

and finished even and smooth in (i)Cement mortar 1:3 (1- 54.81 171.71 Sqm ₹

cement:3-sand). plastering on ceilings and sofits of stairs

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

74 Providing 20 mm thick double coat mala cement plaster on

interior brick / concrete work for plastering comprising of base

coat of 12 mm thick cement plaster in cement mortar (1

Cement : 4 coarse sand) in rough finishing and 8 mm thick top 200.89 283.95 Sqm ₹

coat of cement mortar 1:2 (1 Cement : 2 Coarse sand) finished

with trovel including scaffolding curing etc. complete.

75 Providing and applying with two coats 20 mm thick sand faced

cement plaster at outside RCC / brick on work at any level

where specified consisting of 12 mm thick backing coat of 137.64 342.41 Sqm ₹

C.M. 1:3 (1 cement: 3 sand) and 8 mm thick finishing cost of

C.M. 1:1 (1 cement : 1 sand) etc. complete

76 White washing with lime on wall surfaces (two coats) to give

an even shade including thoroughly brooming the surface to

remove all dirt, dust, mortar drops and other foreign matter etc.

at all levels as directed.

77 Wall painting in three coats ( incl. priming coat of approved

make) with plastic emulsion paint of approved brand / make

preferably like Asian paint , Burger, Nerolac etc. on new

surface to give an even shade incl. thoroughly brushinq the 137.64 165.99 Sqm ₹

surface from to remove all dirt, and remains of loose powdered

materials.with birla or Asian acrylic lapy (putty) twocoats of

primer of approved brand.

78 Providing and fixing FRP frame size 125 X 65 mm and 35 mm

thick FRP shutter with wood grain raised panel design finish

shutter having extra reinforcement on sides and edges and in

GEL coat finish. The core of shutter is to be filled up with

injected fibre extingushing grade polyurathane foam done in

situ along with embedded wooden pieces for stiffening and 8.64 2019.98 Sqm ₹

also for taking hinges and fixtures. The whole FRP frame and

shutter is to be water proof, weatherproof, termite proof and

resistance to mild acid/ Alkali resistance including S.S. hinges

with necessary screws and alluminium fixtures and fastening.

79 Providing and fixing glazed louvered glass windows and

ventilators with teak wood frame 10cm. x 7cm. size including

3 coats of oil painting to wood work etc.complete. with 5.76 4434.35 Sqm ₹

wooden louvers plank 12mm thick (upto 10 ton)

80 Providing and laying white glazed tiles 6mm thick in flooring

treads of steps and landing laid on a bed of 12mm thick cement

mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush 31.35 868.55 Sqm ₹

pointing in white cement. (upto 10 ton)

81 Providing and laying coloured glazed tiles of the size 300 mm

x 200 mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting,

risers of steps and dedo on 10 mm. thick cement plaster 1:3 (1 92.09 1488.24 Sqm ₹

cement : 3 coarse sand) & jointed with white cement slurry.

82 Providing and laying broken chine mosaic flooring for terrace

using 12 mm to 20 mm broken pieces of glazed tiles to be laid

over cement mortar 1:3 to plain or slope and to be tempered to

bring mortar creme out upto surface using white cement 40.25 779.70 Sqm ₹

including rounding off junctions and extending them upto

cm along the wall,clearing with water and oxalic acid etc. as

83 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure polythene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type 60.00 280.23 Rmt. ₹

fittings, wall clipsetc. including making good the wall ceiling

and floor.(F) 75mm

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

84 Providing and fixing in position cowel went to pipes.(B) 75mm

85 Providing and fixing wsh down water closet (European type,

W.C. Pan) with integral P or S trap including jointing the trap

with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) 6.00 1356.81 Each ₹

(Seal and cover to be measured and paid for separately)(A)

vitreous China Pattern :(i) in white colour

86 Providing and fixing 100mm size P or S trap for water closet

squatting pan including jointing the trap with the pan and soil

pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)(A)

Vitreous China.

87 Providing and fixing in Cement Mortar 1:3 (1-Cement : 3-

coarse sand)a, pair of white vitreous China 250mm x 130mm x

30mm footrest to long pattern squatting pan water closet.

88 Providing and fixing 12.5 Litres low level flushing cistern with

a pair, of C.I. or Mild brackets, complete with fittings such as

lead valve less syphon, 15mm nom.nal size brass ball valve

with polythene float, C.P brass handle unions and couplings for

connections, with inlet, outlet and overflow pipes, 40mm dia. 6.00 2370.39 Each ₹

porcelain enamelled flush bend including cutting holes in walls

and making good the same connecting the flush bend with

cistern and closet (overflow pipe to be measured and paid for

separately)(A) Vitreous China (I) In white colour

89 Providing and fixing plastic seat and cover for wash down

water closer with C.P. brass hinges and rubber buffers. (B) 6.00 291.33 Rmt ₹

Black plastic seal and cover.

90 Providing and fixing washbasin with single hole for pillar tap

with C.I. or M.S. brackets painted white including sutting

holes and making good the same but excluding fittings.(A) 2.00 1684.95 Each ₹

Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm

size. (i) In white colour.

91 Providing and fixing C.P. brass waste for washbasin or sink.

92 Providing and fixing M.I. fisher union for washbasin or sink.

93 Providing and fixing 100mm sand cast iron grating for gully,

floor or Nahni trap.

94 Providing and fixing screw down bib taps of following size.(B)

Brass chromium plated screws down Bib Tap. (i) 15mm 6.00 186.83 Each ₹

95 Providing and fixing pillar tap, capstan head, screw down high

pressure with screws, shanks and back nuts. (i) 15mm dia. 4.00 308.73 Each ₹

96 Providing and fixing brass screw down stop tap.(A) 15mm dia.

97 Providing and fixing Gun metal check or non-return fullway

wheel valve.(C) 25mm dia.

98 Providing and fixing chromium plated brass half trun flush

cock of approved quality including fixing in pipe line etc. 2.00 263.77 Each ₹

complete.(ii) 25mm dia.

99 Providing and fixing Rubber plug for sink or wash basin. 4.00 17.15 Each ₹

100 Providing and fixing chromium plated, bottle trap with

necessary couplings of approved quality for wash basin.

101 Providing and fixing concealed center point to wall ceiling &

floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia. 6.00 170.36 Each ₹

nominal bore tube fittings and clamps including making good

the wall, ceiling and floor etc. complete.[A] 15 mm.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

102 Providing and fixing concealed center point to wall ceiling &

floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia. 60.00 253.82 Rmt. ₹

nominal bore tube fittings and clamps including making good

the wall, ceiling and floor etc. complete.[A] 25 mm

103 Providing laying and jointing in true line and level 32mm dia.

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings

make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two metre 60.00 119.09 Rmt. ₹

C/C or shall be concelled as directed including necessary

fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

104 Providing, laying and jointing in true line and level

diametre U.P.V.C (Type B) conforming to IS 13592-1992 with

one end plain and other end socketed with rubber ring, &

fittings conforming to ISI 14735-1999 of approved make for

drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of 40.00 876.90 Rmt. ₹

PVC clamp of the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary fittings such

as bends, shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of all

105 Providing, laying and jointing in true line and level

diametre U.P.V.C (Type B) conforming to IS 13592-1992 with

one end plain and other end socketed with rubber ring, &

fittings conforming to ISI 14735-1999 of approved make for

drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using of 50.00 834.38 Rmt. ₹

PVC clamp of the size 160 mm diametre x 210 mm length x

196 mm heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary fittings such

as bends, shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of all

106 Providing and fixing PVC SWR Nahni trap IS 14735 for drain -

100 mm diameter with jali of the following nominal diameter

of self cleansing design with C.I scread down or hinged grating 10.00 586.27 Each ₹

including the cost of cutting and making good the walls.

107 Providing erecting and fixing double coated Syntex PVC.

(ISI) water tank of required capacity each with all necessary

fittings and connection etc. complete on terrace.

108 Providing and fixing S.W. gully trap with C.I. grating brick

masonry chamber and water tight C.I. cover with frame of

300mm x 300mm size (inside) with standard weight.(i) Square

mouth traps.(B) 150mm x 100mm size P or R type

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

109 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-

cement :2-coarse sand : 4-graded stone aggregate 20mm

nominal size) foundation concrete 1:3:6 mix (1-cement : 3-

coarse sand :6-Brick bats 40 + 50mm size) inside plastering

15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse

sand) finished with a floating coat of neat cement and making

channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse

sand :4-stone aggregate 20mm nominal size) finished smooth

complete including curing and festing (i) Inside size 900mm x 4.00 19349.63 Each ₹

1200mm and 1.5M. deep including C.I. cover with frame size

560mm diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame

Kg.)(A) With 230mm thick walls of brick msonry using brick

having crushing strength not less than 35Kg. / Sq.cm. in

Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B type

depth 1.50 Metre for 150mm diameter sewer.

110 Providing and fixing cast iron steps of size 500mm x 150mm x

22.5mm and painting with two coats of Anti-corrosive paint 3.00 151.50 Each ₹

111 Supplying and fixing C.I. cover 300mm x 300mm without

frame for Gulley trap (Standard pattern) te weight of cover to 4.00 497.14 Each ₹

be not less 4.53 Kg.) (upto 10 ton)

112 Constructing Brick masonry road gully chamber 500mm x

450mm x 600mm including 500mm x 450mm C.I. horizontal 4.00 2017.19 Each ₹

grating wih frame complete. (upto 10 ton)

113 Constructing brick masonry chamber for underground C.I.

Inspection chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of

cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 4.00 7180.44 Each ₹

20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete.(iii) Inside dimensions 600mm x mm and 450mm

deep for pipe lines with three or more inlets. (upto 10 ton)

114 Providing and laying Polished granite stone 20 to 25mm thick

black in urinal partation, door / windows's jembs, soffits and

sills inlcuding all labour charges with half round edge 1.80 2567.79 Sqm ₹

moulding for Granite with all required materials etc. complete.

115 Carring out plinth treatment to post construction / existing

structure by spraying chemical solution for termite control

treatment including labour and material consistment with I.S.I

specification. Using Chlordene and Chiorpurfiles 20 EC. As

Per 6131_paret-II Consentration Weight one percent is 74.25 59.46 Sqm ₹

recommended i.e one litre 20 EC chemical emulsion with

liter give 1 % concrentration inclusive of one litre chemical

emulsion appication at the rate of 5 Litre chemical / Sqm of

surface is recommended as per I.S

116 Excavation for foundation for loose and soft soil including

sorting out and stacking of useful materials and disposing of

the excavated stuff up to 50 meter lead. a) From 0.0 to 1.5 m.

117 Excavation for foundation for loose and soft soil including

sorting out and stacking of useful materials and disposing of

the excavated stuff up to 50 meter lead.b) From 1.5 to 3.0 m.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

118 Providing and laying cement concrete 1:3:6 (M10) (1 Cement :

3 Coarse sand : 6 Hand Broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of formwork

in Foundation and Plinth

119 Brick work using common burnt clay building bricks having

crushing strength not less than 35kg / Sq. C. M. in ramp, steps

and Foundation & Plinth in cement morter1:5 (1 cement :

coarse sand) including racking out joints, curing, scaffolding

required if any etc.complete, as directed.

120 Providing and applying 15 mm thick cement plaster in single

coat on brick work with floating coat of net cement slurry for

interior plastering of pumphouse and outside plastering of

sump upto finished even and smooth in Cement motar 1 : 3 (1 59.00 246.05 Sqmt ₹

cement : 3 sand) including racking out joint curing,

scaffolding required if any, with necessary cement finishing

etc. complete as directed.

121 Providing and laying controlled cement concrete M.250 and

curing complete including the cost of formwork but excluding

the cost of reinforcement for reinforced concrete work in RCC

122 Providing TMT Bar FE 500D reinforcement for R.C.C. work

including bending, binding and placing in position complete 1440.00 77.29 kg ₹

upto floor two leve (upto 10 ton)

123 Manhole Cover

C.I. Cover with frame 500mm x 700mm

124 Excavation for foundation upto 1.5 m depth including sorting

out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead.(A) Loose or soft soil a)

From 0.0 to 1.5 m.

125 Excavation for foundation 1.5 m to 3.0m depth including

sorting out and stacking of useful materials and disposing off

the excavated stuff upto 50 Meter lead.(A) Loose or soft soil a)

126 Filling available excavated earth (excluding rock) in trenches.

plinth, sides of foundations etc. in layers not exceeding 20 cm.

in depth consolidating each disposited layer by ramming and

127 Providing and casting in situ C.C. in grade M-15 (approx.

corresp. to prop. 1:2:4) (proportions as per mix design or as per

Table 9 of IS456 2000 in masses by weigh batching ) using

granite, quartzite trap metal of size 6 mm to 20 mm for RCC

work, including scaffolding centering, form work, needle 8.00 4732.00 cmt ₹

vibrated consolidation, curing comp. up to 6 meter depth or

height (excluding cost of reinforcement and neat finishing)

with centering and shuttering/deshuttering etc. comp. for

structure for other than water retaining. Footing (without form

128 Providing and cast in situ C.C. in grade M-25 proportions of

ingredients as per mix design by weigh batching using granite,

quartzite trap metal of size 12 mm to 20 mm and or 6 mm to

12 mm including scaffolding centering formwork, needle

vibrated consolidation, curing and hydrulic testing etc. ₹

complete (excluding cost of reinforcement) with centering &

shuttering/ deshuttering etc. for all water retaining structures.

a) R.C.C. footings & Raft

129 b) R.C.C. Columns 8.00 8467.45 cmt ₹

130 c) R.C.C. beams, lintels and bracket for gantry or chain pully

blocks, plinth beams, tie beams, weather shed etc.

131 d) R.C.C. slabs and platform 22.00 7479.60 cmt ₹

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

132 Supply cutting, Bending, Binding and placing in position steel

as per plan and design and as per ISS 2502 including cost of

steel and binding wire for reservoirs/ structures only including

lift up to 6 meter height or depth below G.L. for all diameters.

Deformed(TMT)bars confirming to relevant IS Fe-500 grade

for all diameters.

133 Supplying, cleaning, cutting, bending, welding, fabricating,

erecting, structural steel in position irrespictive of location and

levels as per drawings including handling and transport, etc.

complete including applying two (2) coats of primer red oxide

and two (2) coats of approved quality paints

134 Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Lime Mortar 1:1.5 (1- Lime putty :1.5 -fine

sand)(B) Conventional

135 Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Lime Mortar 1: 2 (1- Lime putty : 2 -fine

sand)(B) Conventional

136 Providing 15mm thick cement plaster in single coat on Rough

(Similar)side of single or half brick walls for interior plastering

upto floor two level and finished even and smooth in (i) 320.00 246.05 Smt ₹

Cement mortar 1:3 (1-cement:3-sand) & Finishing with a

floating coat of neat cement slurry.

137 20mm thick sand faced cement plaster on walls upto height

metres above ground level consisting of 12mm thick backing

coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing 300.00 342.41 Smt ₹

coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

138 Finishing wall with weather proof exterior emulsion paint on

wall surface (two coats) to give an required shape even shade

after thoroughly brushing the surface to remove all dirt, and

remains of loose powdered materials.etc complete

139 Distempeing (Two coats) with oil bound distemper of

approved brand and manufacture and of required shade on wall

surfaces to give an even shade, over and including a priming

coat with distemper primer of approved brand and manufacture 320.00 75.68 Smt ₹

after thoroughly brushing the surface free from mortar

dropping and other foreign matter and also including preparing

the surface even and sand papered smooth.

140 Applying two coats of putty & two coats of primer of approved

brand and manufacture on new wall surface to give an even

shade including thoroughly brushing the surface free from 320.00 40.59 Smt ₹

mortar dropping and other foreign matter and sand papered

141 Painting two coats including priming coat on new steel & other

metal surfaces with enamel paint, brushing, interior to give an

even shade including cleaning the surface of all dirt, dust, other

foreign matter.

142 Providing and laying broken China Mosaic flooring for terrace

using 12 mm to 20 mm broken pieces of glazed tiles to be laid

over Cement mortar 1:3 to plain or slope and to be tempered to

bring mortar crème out upto surface using white cement 60.00 779.70 Smt ₹

including rounding of junctions and extending them upto

cm. along the wall, clearing with water and oxalic acid etc. as

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

143 Providing and laying polished Kota stone slab flooring over

mm (average) thick base of cement mortar 1:6 (1 cement :

coarse sand) laid over and jointed with grey cement slurry 60.00 1090.70 smt ₹

including rubbing and polishing etc. complete . Avg - 30 mm

144 Providing and laying polished kota stone slab 25mm thick in

risers of steps,skirting Dedo and pillars laid on 10mm thick

cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with

gray cement slury mixed with pigment to match the shade of

slab including rubbing and polishing etc. complete.

145 Granite in Jams and Sills of the window and ventilation and

Door with one molding as directed by Engineer-in-charge. 6.00 3282.50 smt ₹

146 Providing and fixing window having extruded aluminum

Colour anodized section frame main outer size 95mm x 24mm

x 1.17 mm (of Jindal Section no : 2459 @ wt. of 0.738 Kg/mt),

horizontal Three track member size 92mm x 31.75 mm x

mm (of Jindal Section no. 8688, @ Wt. 1.07 Kg/mt), vertical

member of size 92mm x 31.75mm x 1.50 mm (of Jindal

Section no. 8933, @ Wt. 1.06 Kg/mt.) with sliding shutters of 6.00 1583.95 smt ₹

horizontal member size 40mm x 18mm x .29 mm (of Jindal

section no. 8947 @ wt. 0.456 Kg/mt.) vertical member of size

40mm x 18mm x 1.29mm (of Jindal Section no. 8949 @ wt. of

0.456 Kg/mt with 5 mm thick transparent bronze colour tinted

float glass with powder coated aluminum fittings and fixtures

and transparent silicon sealant glass fixing to frame as per

147 Supplying, fixing Push and Pull, 20 gauge rolling shutter of

approved make for the sizes indicated on drawings including

hood cover, channel sliding assembly, helical coil springs,

brackets, interlocking latches, locking arrangements, painting 24.00 4378.35 smt ₹

with 2 coats of enamel paint over one coat of approved primer

paint etc. complete. Shutters having width below 3.5M (gear

148 Providing and fixing in position 60 cm wide MS ladder with

angle of 75 x 75 x 6 mm as support and 50 x 50 x 5 mm angle

as step at 200 mm c/c including (both side) GI side railing with

ISA 75 support including fixing in cement concrete for any

height including making holes in RCC walls if any and making 24.00 5686.30 Rmt ₹

good the RCC wall / masonry wall after fixing work of

staircase etc. complete as directed including two coats of

approved quality oil paint directed including two coats of

approved quality oil paint over one coat of approved quality

149 Providing and fixing PVC pipe of 6Kg./csmt of 140 mm dia

for rain water with shoe.

150 Filling in plinth with sand under floors incuding watering,

ramming, consolidation and dressing complete

151 Providing throating or plaster drip and moulding as instructed

by Engineer in charge.

152 Carting from 50mt to 5 Km 60.00 419.92 Cmt ₹

149 Excavation for foundation for loose and soft soil including

sorting out and stacking of useful materials and disposing of

the excavated stuff up to 50 meter lead. a) From 0.0 to 1.5 m.

150 Excavation for foundation for loose and soft soil including

sorting out and stacking of useful materials and disposing of

the excavated stuff up to 50 meter lead.b) From 1.5 to 3.0 m.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

151 Providing and laying cement concrete 1:3:6 (M10) (1 Cement :

3 Coarse sand : 6 Hand Broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of formwork

in Foundation and Plinth

152 Brick work using common burnt clay building bricks having

crushing strength not less than 35kg / Sq. C. M. in ramp, steps

and Foundation & Plinth in cement morter1:5 (1 cement :

coarse sand) including racking out joints, curing, scaffolding

required if any etc.complete, as directed.

153 Providing and applying 15 mm thick cement plaster in single

coat on brick work with floating coat of net cement slurry for

interior plastering of pumphouse and outside plastering of

sump upto finished even and smooth in Cement motar 1 : 3 (1 27.00 246.05 Sqmt ₹

cement : 3 sand) including racking out joint curing,

scaffolding required if any, with necessary cement finishing

etc. complete as directed.

154 Providing and laying controlled cement concrete M.250 and

curing complete including the cost of formwork but excluding

the cost of reinforcement for reinforced concrete work in RCC

155 Providing TMT Bar FE 500D reinforcement for R.C.C. work

including bending, binding and placing in position complete 550.00 77.29 kg ₹

upto floor two leve (upto 10 ton)

156 Manhole Cover

C.I. Cover with frame 500mm x 700mm

157 RECEPTION TABLE WITH PADESTAL

Providing & fixing reception table made as described

below: Counter: At 1050 mm height 12mm thick frosted

glass with crystel edge. Glass to be rest on table working top

with 25mm dia SS pipe with sturd.Work surface : At 725 mm

height made from 37mm th. Ply wood with 1.0mm thick

laminate on top & open edges.Modesty panel: Below work

surface 18mm thick ply with 1.0mm thick laminate.

Or shera board panel duly finished in monocoat

polish.Verticle box-18mm thick ply with 6mm thick

corian sheet. Entire work shall be carried out as per

the detailed technical specifications, drawings and as

per the instruction of Architect.Padestal in laminated

finish. (2 set of drawer box). Pedestal made up of 18 mm thick

ply wood 1.0mm thick laminate with PVC lipping on all edges 8.00 Rmt. 4282 ₹

for top panel, side panel, front skirting and fascia for (top,

middle & file) drawer. Drawer made up of 18 MM thick ply

wood with 1.0mm thick laminate with PVC lipping on all

edges for back panel, bottom panel of pedestal bo you NRC of

70% , The cavity of framework should be inserted with

acoustical foam. the end situation or edge closing at all

windows and doors, at skirting level and at ceiling leel

shall be executed with natural wood patta with color

matching melamine polish. the cut Rate is inclusive of

telescopic channel of ebco make or equivalent for supporting

drawer. Multi purpose lock of Vijayan/Godrej make. Key

board tray of Ebco make with mouse tray. CPU trolley:

M.S.powder coated trolley. Complete with technical

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

158 CENTER TABLE (0.9 x 0.6m)

Providing and supplying modular table as below

specification:Table top 10mm thick float glass with

bevelled edge. Top to be rest on 25mm dia. S.S. brush 2.00 Nos. 3800 ₹

finished leg. Steel frame height is 450mm .Top in Clear Glass

of 10mm thk with edge polished of size : 900 mm x 600 mm x

450 mm. Complete with technical specification.

159 STORAGE CABINET

Supply & fixing storage cabinets in completely knock down

per described below specification:

Entire body & shutter (openable or sliding) to be made from

18mm thick pre-laminated particle board with 2mm thick PVC

edge beading matching the laminate. Adjustable shelves of

400mm depth to be provided with SS rod for file hanger

system as required by Shelves to be made from pre-laminated

particle board. All open edges to be finished with 2mm

thick PVC edge beading matching the laminate. Complete 4.00 Smt. 6610 ₹

with all necessary hardware & fittings such as lock, SS brush

finish D type handles, SS auto hinges, of approved make etc.

complete as per the detailed technical specifications, drawings

and as per the instruction of Engineer-in-charge. Length x

height (bottom of false ceiling) to be taken for

measurement purposes. The contractor will have to take the

exact dimension between the walls before supplying the

storage units.Complete with technical specification.

a) Full height storage.

b) Middle height storage 4.00 Smt. 6693 ₹

c) Low height storage 4.00 Smt. 6610 ₹

a) HIGH BACK CHAIR - MODEL : CHE -

Supply and erecting synchro tilt mechanism with Any position

locking arrangement, Nylon mesh back for air circulation,

steps up armrest position to suit your posture, Anti topple

chrome polished base, Class- 3 gas lift for seat height 2.00 Nos. 12500 ₹

adjustment & glass filled nylon castors for smooth movement,

45 dc mould cushion in seat, waterfall design seat for better leg

suport, Unique design of back with Mechanical lumber support

adjustment device, 4 way adjustable head rest & S shaped

back design to support the spine

b) MEDIUM BACK CHAIR - MODEL : TOR -

Supply and positioning push back with single back lock

system, PP Fix Arms, Seat cushioned & Back in black 2.00 Nos. 4600 ₹

Net/Mesh, Powder coating metal base with twin wheel

nylon castors, Gas lift for seat height adjustment

c) STAFF CHAIR - MODEL- priviya-7001

Supply & positioning SS fix arms, Multiple point locking

system with synchro mechanism, Gas lift for seat height 4.00 Nos. 3450 ₹

adjustment, chrome base

with twin wheel nylon castors

d) FIX VISITORS CHAIR - MODEL : VIT-1002

Suppling and positioning fix chair with Seat cushion & plastics

with 16 gauge CRC capsule pipe.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

e) M. S PERFORATED BENCH

Providing and Supplying sofa as below specification.

Metalic understructure with Metal Arms and Legs with

silver gray finish powder coating with dimention as indicated

in the dwg. PU moulded foamin seat & back of 62 density 2.00 Nos. 3440 ₹

Under seat parallel support min. 14 gauge square pipes

duly powder coated.

* Glide screw at the bottom for level adjucement.

161 ROLLER BLINDS

Providing & fixing roller blinds of following specifications:

a) Eco black out

Composition : 100% POLYESTER

Coating : PIGMENTED ACRYLIC

Width : 120.00 Smt. 860 ₹

Thickness : 0.45MM + / -5%

Weight : 330GSM + /- 5%

Light Fastness : > 7 (BLUE WOOL SCALE),

Supplying and stacking of good earth at site including royalty

162 and carriage upto 5 km lead complete (earth measured in 45.00 515.60 Cu Mt ₹

stacks will be reduced by 20% for payment).

Supplying and stacking of well decayed cattle manure at site

including royalty and carriage upto 5 k.m.lead complete (Cattle

manure measured in stacks will reduced by 8% for Payment).

Rough dressing the trenched ground including breaking clods.

165 Fine dressing of the ground. 150.00 3.70 Sq MT ₹

Mixing earth and sludge or manure in the required proportion

specified or directed by the Officer-in-charge

Spreading of sludge, dump manure and/or good earth in

required thickness as per direction of officer-in-charge (cost of

sludge, dump manure and/ or good earth to be paid separately).

Preparation of beds for hedging and shrubbery by excavating

60 cm deep and trenching the excavated base to a further depth

of 30 cm, refilling the excavated earth after breaking clods and

mixing with sludge or manure in the ratio of 8:1 (8 parts of

stacked volume of earth after reduction by 20%: one part of

stacked volume of sludge or manure after reduction by 8%),

168 flooding with water, filling with earth if necessary, watering 52.50 222.85 Cu Mt. ₹

and finally fine dressing, leveling etc. including stacking and

disposal of materials declared unserviceable and surplus earth

by spreading and leveling as directed, within a lead of 50 m,

lift up to 1.5 m complete (cost of sludge, manure or extra earth

to be paid for separately)

Digging holes in ordinary soil and refilling the same with the

excavated earth mixed with manure or sludge in the ratio of 2:1

by volume (2 parts of stacked volume of earth after reduction

by 20% : 1 part of stacked volume of manure after reduction by

169 8%) flooding with water, dressing including removal of 600.00 18.70 EACH ₹

rubbish and surplus earth, if any, with all leads and lifts (cost

of manure, sludge or extra good earth if needed to be paid for

Holes 45 cm dia, and 45 cm deep

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

Plantation of Trees, Shrubs, and Hedge at site i/c watering and

removal of unserveiceable material’s as per direction of officer

in charge (excluding cast of plant & water)

Providing and stacking of Azadirachta indica ( Neem ) of

171 height 120-130cm in big polybag of size 25 cm as per direction 10.00 65.00 EACH ₹

of the officer-in-charge. ( Neem )

Providing and stacking of Ficus bengalensis (Bargad) of height

120-135 cm. in big poly bags of size 25 cm as per direction of

the officer-in-charge. (Wad Banyan, Ficus benghalensis )

Providing and stacking of Plumeria alba dwarf dwarf of height

90-105 cm. with 3-4 branches and thick stem in big size HDPE

bags as per direction

of the officer-in-charge. (West Indian Jasmine)

Providing and stacking of Nauclea cadamba (Kadam) of height

174 150-165 cm. in big poly bag of size 25 cm as per direction of 15.00 65.00 EACH ₹

the officer-in-charge. (Kadam)

Providing and stacking of Ficus religiosa (Peepal) of height

175 150-165 cm. in big poly bags of size 30 cm as per direction of 15.00 65.00 EACH ₹

the officer-in-charge. (Peepal)

Providing and stacking of Cassia fistula (Amaltash) of height

176 120-135 cm. in big poly bags of size 25 cm as per direction of 15.00 65.00 EACH ₹

the officer-in-charge. (Amaltash , Garmado)

Providing and stacking of Delonix regia (Gulmohar) of height

177 150-165 cm. in big poly bags of size 25 cm as per direction of 15.00 60.00 EACH ₹

the officer-in-charge.

Providing and stacking of Foxtail palm of ht. 240-270 cm

178 bottom girth 35-40 cm well developed in big size HDPE bags 10.00 650.00 EACH ₹

as per direction of the officer-in-charge.

Providing and stacking of Calliandra hybrida of height 105-

179 120 cm., well branched, bushy inbig size HDPE bag as per 80.00 90.00 EACH ₹

direction of the officer-in-charge.

Providing and stacking of Caesalpinia pulcherrima species of

180 height 45-60\ cm. in earthen pot of size 20 cm as per direction 80.00 45.00 EACH ₹

of the officer-in-charge.

Providing and stacking of Bauhinia tomentosa (yellow) of

181 height 60-75 cm. in earthen pots of size 20 cm as per direction 80.00 45.00 EACH ₹

of the officer-in-charge

Providing and stacking of Euphorbia caracasana (bronze

182 colour leaves) of height 60-75 cm. with 4-5 branches in bag of 80.00 55.00 EACH ₹

size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 30-45 cm.

183 with 3-4 branches in poly bags of size 20 cm as per direction of 60.00 20.00 EACH ₹

the officer-in-charge.

Providing and stacking of Hibiscus rosasinensis of height 90-

184 105 cm., bushy in big size HDPE bag as per direction of the 60.00 90.00 EACH ₹

officer-in-charge

Providing and stacking of Tabernaemontana coronaria

185 (Chandni single) of height 90-105 cm.,bushy in big size HDPE 60.00 80.00 EACH ₹

bag as per direction of the officer-in-charge.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

SITC of 16 Mtr. - M.S. polygonal High Mast with following

accessories.( Item no. a to g)

Supplying, erecting, testing, commissioning approved make

M.S. Polygonal High Mast Pole having following general

(a) Polygonal Section fabricated from M.S. Plate confirms

BSEN 10025 & Hot deep galvanised minimum 65/86 micron

(as per IS 01461) Lantern carrige with ring and rubber lines for

errection of luminaries of suitable site.

(b) Maximum telespopic section not more than four

(c) Double drum gear pipe motorized winch with 6 mm dia. Ss

rod ( for 16 mtr and above size)

(e) Bottom most section suitable for mounting reversible motor

and switch gears having door not more han 1400 mm x

mm with water proof gasket and hinges and locking

186 arrangement. 1.00 171574.17 Nos. ₹

(d) Approved make L.E.D aviation light = 1 No. Lighting

arrester = 1 No. with necessary wiring of 2.5 sq.mm 5 core ISI

copper cable Unarmoured.

(f) Pole structure comprises suitable size of reversible motor,

cable and necessary switchgears.

(g) bottom section shall have suitable soze of thickness

supports ribs foundation bolts nuts etc.

(h) Item not comprises the cost of lanteans.

(i) Necesssary Cement concrete foundation as per IS including

testing and commissioning of the entire structure for following

size of HIGH MAST poles.(Cat-III)

(2) High Mast 16 mtr TOP A/F 105 MM BOTTOM A/F

mm. No. of section No.-2 Bottom thickness - 4 mm size,Base

plate -520x16,Foundation bolt size M24 x 880.Qnty. 8 Nos.

Suitable for mounting fitting of light - 8 nos

Supplying & erecting LED Flood light fittings with high power

white LEDs wattage of 1Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free

high pressure die cast alluminium housing with amooth finish

powder coated and heat sink extruded alluminium with diffuser

and polycarbonate optics/lenses with company mark/name

187 engraved or embossed 120 to 300V, Power factor more than 8.00 8793.64 No ₹

0.95, THD<10%,CCT 5000K to 5700K, Uniformity ratio

>0.45, Luminairee efficiency>85 lumens/watt. LED driver

efficiency>85%, DREE/OSRAM/PHILIPS

Lumileds/NICHIA/SEOUL/BridgeLux(U.S.A) make LED used

for luminaire.(Each fitting required LM-79 & LM-80

certificates) ( IP-65,240 Watt,Cat-III)

Providing, laying, testing & commissioning of 1 x 4.0 Core x

16 Sq. MM, XLPE (IS: 7088 (i) - 88), ISI Mark, Armoured,

188 Multistranded, Aluminium Conductor suitable for 1.1 kV 100.00 122.43 Mtr ₹

grade to be laid 90 Cms under ground or to be laid on wall

with necessary clamps

SITC of Double Compression Type Brass Cable Gland with

rubber hood suitable for 1 x 4.0 Core x 16 Sq. MM., XLPE

Alu. Armoured cable complete with outgoing tails, insulating

SITC of Solderless Crimping Type Aluminium Lugs (4 Nos.

lugs per termination) suitable for 1 x 4.0 Core x 16 Sq.mm.

190 XLPE Aluminium Armoured cable tail complete erected with 8.00 13.42 no ₹

insulating materials for each termination. (Total 3 Nos.

Termination per dist. box)

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

Supplying & erecting earth pit of minimum bore dia.150mm

size approved make Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS 3043-1987 made of corrosion free

G.I.Pipes having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following

191 type of applications. 1.00 4859.62 No ₹

(a) For Electrical Installation up to 440V in normal soil Length

of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg. Providing and

erecting HOT deep Galvanised iron strip wire 8 to 16 SWG.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I.

pipe with necessary coupling buch buried in specially prepared

earth pit & G.I. earth wire of 8 SWG erected & connected as

directed (For panel). Sor item no. 3-14-6(B)+3-14-5+3-14-9

Providing & laying of 50 MM Nominal OD Doubled Walled

Corrugated Pipes (DWC) of polyethylene (conforming to IS

192 14930 - II) with necessary connecting accessories like coupler, 700.00 55.44 Mtr ₹

Tee, L - Bow, etc. of same material at required depth (90 cms)

including excavat

Supplying & erecting MINI SECTION PILLAR 75 x 60 x

cms fabricated from 16 Gauge thick joint legs M.S. Sheet with

angle iron legs 45 cms long made from 35 x 35 x 5 mm thick.

Jointless M.S. Angle with cable clamps to be burried in ground

to have appropriate erection to work Uniform Until erected

with cement concrete foundation and 45 cms high bricks work

finishing with plaster etc. hinged double door with 3" x 4"

vision panel covered with Mesh & V. panel overlapping with

193 flap for meter reading internally supported on both side, with 1.00 3180.10 Each ₹

internal and outside looking arrangement with look and keys in

duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is

welded and other with nut and bolt for erecting backlite sheet.

Painting the Section Pillar inside and out side with three tank

powder coated paint.. section pillar roof should be without

joint with water leakage proof & tested as per IP 55 test &

followed by IS 2147 of

Providing & Fixing 0f backelite sheet 12 mm thick HYLLAM

make grade : P-100 on existing angle iron frame.

Providing and erecting approved make Digital time switch

having lithium cell 6 years operative and operate battery

backup 1 channel day clock with 14 memory programme,

suitable to operate on 240V + 5%, 16A with, floating contacts

195 minimum switching setup time 1 minimum & LCD display. 1.00 2801.29 Each ₹

Also comprised permanent ON/OFF switching programming

switches & housed in fire proof thermoplastic enclosure &

transparent cover erected as required with necessary

connection erected as directed.

Providing and erecting AC-3 duty 3 pole power contactor with

2 NO & 2 NC aux contacts complete with 415V/220V

operating coil suitable for (L&T, BCH,T.C., Siemens, C&S

make). (b) for 40 A rating

Providing & erecting 415V MCB FOUR pole switch for

lighting load (B curve) having 10kA breaking capaicity &

confirms to IS:8828 in existing box having following capacity

(a) 40 Ampere Cat. III

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

Drilling (HDD) the road without breaking the road

surface(asphalt)for laying of cable for feeding power supply by

making up to 150mm dia.size of holes at both ends complete.

Making trench in hard murrum/ tar road of suitable width of

cms or required depth for laying any size of cable or locating

the fault all over the run and back filling the same and making

the surface as normal ground.

Providing and erecting Approved make ELCBs / RCCBs

conforming to IS : 12640 and having sensitivity of 30m A and

Short Circuit with stand capacity of 6 KA and suitable for

200 operation on single phase 240 V. having charectorstic of quick 1.00 1976.28 No ₹

acting & tripping with all advance feature & do not incorporate

any electronic component.for following Max. rating. 40 Amp

Providing , erecting , fabricating the M.S. structure as per

requirement on site incorporating proper size of M.S. angles,

201 flats, bars, channels, sections complete with cutting, welding, 200.00 68.93 Sqmtr ₹

grinding & finishing duly painted with one coat of red oxide

(I) Providing & Installing , commissioning & Testing of One

number of Horizontal Filtration Module is Precast Modular

Step well og M 25 grade, designed to capture sediments

primarily from surface runoff water. This Octagonal shape

structure has a circumscribing diameter of approximately

1500mm and a height of 3475mm. A part of the top module is

usually kept above the ground however same can be flushed

with ground. 300/400/610mm are the available height options

in case part of it has to be kept above the ground level. Top

module accommodates indigenously designed 4-Nos Array

Filters to capture sediment effectively within the Horizontal

Filtration Module. This easily removable array filters can be

cleaned within or outside the module using pressurized water.

Total filtation area of this filter is approximately 6000 cm2.

Filtration capacity is 20m3 to 30m3 per hour. These module is

installed prior to the Sand Filtration Module. The inlet and 1.00 1385000.00 Job ₹

outlet of is 160mm diameter UPVC Pipes.(II) Providing &

Installing, ral ladder at 1125 mm with water cleaning system,

labours, hand bucket, lari & other tools. ie.e Trikam , Pavda,

rassa, Battery, G.T. silica etc. with disposing silt as appropriate

places as directed by engineer in charge. No any additional

payment shall be made for cleaning and maintenance work. All

required testing shall be carried out by bidder without any

extra cost for preparing design and drawing for above work

and approval of design from competent authority of GIDC is

in the scope of bidder. No any extra payment shall be made for

the same. Precase slabs held together between two horizontal

precasr slabs ( with 590,, edge length , 50mm thick and hole of

100mm diameter in the centre) Bottom module holds another

type of filter media in the form of sand bed around a

continuous slot fine aperture stainless screen ( 420 mm

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

Screen is fixed to the bottom slab and is fully covered by

filtration sand. Screen creates entry points of the filtration

water. Module filtration capacity & testing upto 20m3 to 30m3

per hour from modular systems only. This module is used for

Roof water harvesting and it is connected with the Exisiting

202 tubewell / recharge well / UG Storage tank.( III ) Providing and

Fixing 200mm M.S. Casing Pipe ( 114 mtr. 5mm Thick)

approved make like ( TATA, JINDAL, SURYA OR As

approved by engineer incharge) with to be connected 200mm

LCG V-wire Screen (36 Mtr) with 450mm Dia Drilling,

water,mudslurry tankers, loading unloading, providing Gravel,

Clay/Sand, gravel packing, Clay/Sand Packing and Cleaning

with compressor 750/200 PSI) total depth of recharge well

should be 152 mtr inclusive of mud pit and mud refilling, site

cleaning etc.(IV) The above work is including as per approved

drawing and required to completed the work, (i) Excavation

for foundation with refilling upto required depth including

sorting out and stacking of useful materials and disposing off

the excavated stuff with all lead and lift in any kind of soil, (ii)

Providing and Laying on concrete 1:2:4 (1 Cement : 2- course

sand : 4 graded stone aggregate 20mm nominal size ) and

curring complete including cost of form work and

rainforcement etc complete ( iii) Brick work using common

burnt clay building bricks having crushing strength not less

than 35 kg/Sq.Cm in foundation and plinth in Cement Mortar

1:6 ( 1- Cement : 6- Finesand ) (B) Conventional with 15mm.

thick in Cement Plaster 1:3 ( 1- Cement : 3- Finesnad) n single

coat on rough ( similar ) side of single or half brick walls.

(iv) Providing and fixing 150MM Dia (S.S.304) 600MM

Length Leaf Trap ( 6mm Slot) (v) Job work for cleaning of

modules for every pre monsoon for total 5 year ( once in a

Year) with in built intergral ladder at 1125mm with water

cleaning sysyem, labours , hand bucket, lari* other

tools.ie.Trikam, Pavda, Rassa, Battery , G.T. Salia etc. with

disposing slit as appropriate places as directed by Engineer in

Charge. No Any Additonal Payment shall be made for cleaning

and maintenance work. All reuqired testing shall be carried out

by bidder without any extra cost for preparing design and

drawing for above wprk and approval of the design from

compentent authority in the scope of bidder. No any extra

payment shall be made for the same.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

203 Supply, Installation, Testing and Commissioning (SITC) of

Stationary Compactor (200 MT capacity) comprising a

heavy-duty stationary compactor fabricated from MS structural

steel conforming to IS:2062, designed with a rectangular cross-

section body and suitable for continuous municipal solid waste

handling at the RTS; the compactor shall be equipped with a

hydraulically operated heavy-duty guillotine gate mounted at

the front side, actuated through twin hydraulic cylinders, and a

hydraulic container clamping arrangement on both sides to

ensure firm locking of the compaction container during

operation; waste shall be received in a charge box/hopper of

minimum 3 cum capacity and transferred into the compaction

container through a hydraulically operated platen, with platen,

side walls, bottom, top and front plates of adequate thickness

(ranging from 3 mm to 25 mm as per design) to withstand

heavy-duty operations; the system shall include an integrated

hydraulic power pack mounted on the compactor body, a fully 1.00 8538000.00 Nos ₹

automated control panel located at the rear end for safe and

efficient operation, and an electric motor of 15 kW (20 HP)

suitable for 415 V ±10%, 3-phase power supply, complete with

required fuses and electrical protections; the compactor shall

be mounted on a minimum 500 mm flanged up-stand, securely

anchored with grouted bolts on an RCC foundation of

minimum 200 mm thickness; the external surface shall be

treated with anti-corrosive epoxy zinc phosphate primer and

PU paint, while internal surfaces shall be coated with anti-

corrosive epoxy paint; the unit shall be complete in all respects

including testing and commissioning at site, with all civil

works such as covered shed, RCC foundation, compaction

container, hook loader, garbage collection hopper, leachate

collection arrangement and site layout drawings to be provided

ensuring readiness for integration into the overall RTS

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

204 Supply, Installation, Testing and Commissioning (SITC) of

Special Purpose Vehicle Mounted Hook Loader Machine

mounted on 28-ton GVW BS-VI compliant truck chassis,

designed and manufactured as per approved technical offer,

suitable for handling municipal solid waste at the RTS; the

equipment shall consist of a hydraulically operated Hook

Loader Equipment (HLE) capable of lifting, loading,

transporting and unloading open or closed steel containers of

various capacities using the Roll-On / Roll-Off (RORO)

principle, for efficient handling of garbage, garden waste,

debris and similar refuse materials; the HLE shall be provided

with an arm-type hook mechanism, central frame assembly,

telescopic jib with hook, twin hydraulic lifting and tipping

cylinders, standard container locking arrangement, rear roller

assemblies for smooth container guidance, stabilizers and all

necessary hydraulic elements to ensure safe and reliable

operations; the hydraulic system shall be powered through a

PTO driven hydraulic pump coupled to the vehicle 3.00 4660060.00 Nos ₹

engine/gearbox, with complete safety features including

mechanical and hydraulic locking systems, holding valves,

relief valves, and electric/hydraulic interlocks to prevent unsafe

operation, and tipping of the container shall be permitted only

after proper locking; the machine shall have a rated lifting

capacity of 20 tonnes, approximate equipment weight of

kg, and shall be mounted on a suitable 28-ton GVW chassis

(such as Eicher 6028 or Ashok Leyland 2820 or equivalent)

with minimum 180 HP engine output, single day cabin, and BS-

VI emission compliance, with side PTO provision to be

arranged by the customer; all operating controls shall be

ergonomically located for ease of operation; the complete

equipment shall be factory-finished with two coats of anti-

externally, and internal surfaces coated with anti-corrosive

epoxy paint, with colour as per tender requirements, and the

vehicle shall be supplied, installed, tested and commissioned at

site in ready-to-operate condition, complete in all respects.

205 Supply, Installation, Testing and Commissioning (SITC) of 28-

Ton GVW Chassis (Commercial Vehicle Cost Included)

comprising supply of a new, unused BS-VI compliant

commercial truck chassis of 28-ton gross vehicle weight,

suitable for mounting of special purpose municipal solid waste

handling equipment such as hook loader systems; the chassis

shall be from a reputed OEM (Eicher / Ashok Leyland /

equivalent approved make) and equipped with a diesel engine

of minimum 180 HP output, suitable transmission, power

steering, air brake system, standard suspension, and a single

day driver cabin, complete with all mandatory safety, lighting,

instrumentation and emission control systems as per prevailing

CMVR and BS-VI norms; the chassis shall be factory-finished

and supplied with valid roadworthiness, temporary/permanent

registration support, Form-22/22A, insurance facilitation, and

statutory documentation, inclusive of all applicable

commercial vehicle costs, duties, levies and taxes; the scope

shall include delivery of the chassis at site, inspection, and

handing over in ready condition for subsequent mounting of

superstructure/equipment, complete in all respects and

acceptable to the Engineer-in-Charge.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

206 Supply, Installation, Testing and Commissioning (SITC) of

Heavy Duty Compaction Container (20 Cu.M Capacity)

comprising design, manufacture, supply, testing and

commissioning of a 20 cubic metre compaction container,

suitable for handling and transportation of municipal solid

waste and compatible with hook lift / roll-on–roll-off (RORO)

vehicles mounted on 25-ton GVW chassis, as per approved

technical offer; the container shall be fabricated from MS

structural steel conforming to IS:2062, designed to safely carry

a minimum payload of 15 MT, with construction comprising

mm thick MS side and front plates, 6 mm thick MS floor plate,

and 4 mm thick MS roof plate, adequately reinforced with

pressed 6 mm horizontal, side and top stiffeners to withstand

heavy-duty compaction and transportation loads; the container

shall be provided with a heavy-duty rear-end vertically sliding

guillotine door at the loading end, hydraulically operated

through the stationary compactor system, complete with proper

locking and sealing arrangement, and a ratchet mechanism for 4.00 1246450.00 Nos ₹

manual operation of the rear door at the refuse

processing/disposal site; heavy-duty hydraulic clamping plates

shall be provided on both sides of the container for secure

locking with the stationary compactor during compaction

operations; the container shall be fitted with two heavy-duty

rollers of approximately 195 mm diameter and 150 mm width

with 45 mm diameter axle at the rear/aperture end to facilitate

smooth rolling-on and rolling-off during loading and unloading

operations on the hook lift vehicle; the container shall be

mounted on a robust sub-frame suitable for hook lift operation,

and an “A” frame lifting arrangement of heavy-duty steel

sections shall be provided at the front end, complete with

lifting pin positioned to match the hook lift geometry; the

finished with approved anti-corrosive primer and protective

paint system, supplied in ready-to-use condition, and tested

and commissioned to the satisfaction of the Engineer-in-

Charge, complete in all respects.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

207 Supply, Installation, Testing and Commissioning (SITC) of

Electronic Pitless Type Weighbridge (60 MT × 10 kg, 14 m

× 3 m) including design, manufacture, supply, installation,

testing, calibration and commissioning of a heavy-duty

electronic pitless weighbridge of platform size 14 m × 3 m and

weighing capacity 60 MT with 10 kg least count, suitable for

continuous commercial operation, complete with pre-calibrated

digital load cell–based weighing system; the weighbridge shall

comprise a robust MS structural steel platform fabricated as

per IS:2062, designed for 150% safe overload and 200%

ultimate overload, supported on six (6) numbers 30 MT

capacity, IP68 protected, hermetically sealed digital share-

beam type load cells (Valiant make or equivalent, Made in

India) with RS-485 full duplex communication, inbuilt

lightning protection, high resolution A/D module and accuracy

within specified combined error limits; the system shall include

digital intelligent terminal (32-bit microprocessor based) with 2.00 950000.00 Nos ₹

battery-backed RTC, high-capacity data storage, SMPS power

supply (90–270V AC), EMI/RFI protection, USB keyboard

connectivity, USB pen drive support, RS-232 serial port,

printer port, remote display port and facility for optional Wi-Fi

connectivity, complete with LCD and LED weight display;

accessories such as load cell junction box, pad plates, load cell

plates, jumbo red LED remote display (2.3 inch), dot matrix

printer, data cables and all interconnecting wiring shall be

provided; the platform shall be finished with approved anti-

corrosive primer and protective paint system, installed on

customer-provided RCC foundation suitable for pitless

installation with recommended approach ramp inclination, and

the entire weighbridge system shall be tested, calibrated with

standard test weights, sealed and commissioned in working

ready for commercial use to the satisfaction of the Engineer-in-

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

208 Supply, Installation, Testing and Commissioning (SITC) of

Signal Light System comprising design, supply, installation,

testing, and commissioning of a traffic/operational signal light

system for safe and efficient control of vehicle movement,

waste handling operations, and personnel safety at the Hajiyani

Baug Refuse Transfer Station (RTS); the system shall include

LED-based signal lights (Red, Yellow, Green) of high-

intensity, weatherproof and corrosion-resistant construction

suitable for outdoor operation, with a robust IP65-rated

enclosure, and integrated control circuitry for automatic and

manual operation; the system shall include control panels with

timers, relays, and push-button overrides, with all necessary

cabling, junction boxes, mounting poles, brackets, and

fasteners, compliant with relevant IS/IEC standards for

electrical safety and visibility; the LED signals shall have long

life, low power consumption, and high luminosity for visibility

under direct sunlight; the cabling shall be laid in conduits or

trays as per site requirements with proper earthing, surge

protection, and power supply from the RTS electrical network;

installation shall ensure visibility from all operational points,

with testing and commissioning carried out to verify correct

sequencing, operational reliability, and compliance with the

functional requirements; the system shall be supplied in ready-

to-operate condition, complete with operation and maintenance

manuals, as-built drawings, and training for operating

personnel, ensuring safe and efficient traffic and operational

control within the RTS premises.

209 Supply, Installation, Testing and Commissioning (SITC) of

Mild Steel Hydraulic and Electromechanical Boom Barrier

System comprising design, manufacture, supply, installation,

testing, and commissioning of a heavy-duty access control

boom barrier for regulating vehicle entry and exit at the

Hajiyani Baug Refuse Transfer Station (RTS); the system shall

include a mild steel boom arm with corrosion-resistant finish,

supported by a robust steel housing enclosing the hydraulic and

electromechanical drive mechanisms, including motor,

gearbox, hydraulic pump, accumulator, and control valves; the

barrier shall be capable of smooth, reliable, and adjustable

opening/closing operations with programmable speed and

dwell time, suitable for continuous operation in outdoor

environments; integrated control panel shall include manual

override, push-button control, interlocks, safety sensors, and

interface for integration with security systems such as CCTV

and access control; the boom barrier shall be equipped with

safety features including photocell or infrared vehicle detection

sensors to prevent accidental closure on vehicles, end-of-travel

limit switches, and hydraulic/electrical overload protection; all

cabling, junction boxes, mounting brackets, earthing, and

surge protection devices shall be provided, with installation on

a properly prepared concrete foundation; the system shall be

tested and commissioned to verify functional operation, safety

compliance, and durability under continuous operational load,

with supply of as-built drawings, O&M manuals, and training

to operating personnel, ensuring reliable and secure control of

vehicular movement within the RTS premises.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

210 Supplying and erecting approved make Octagonal pole made

from HR sheet steel. The pole should be made as per IS. and

shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 12mm

Hylam sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and arrangement for cable 14.00 11411.99 No. ₹

termination to be erected on suitable foundation as per detils

given by manufacturer considering site requirment. (E) 7 Mtr.

Long 70 mm Top X 135 mm bottom dia, 3 mm thickness with

225mmX225mmX16mm base plate, 4-M20 Bolts and 600mm

long with necessary G.I. J Bolts .Approx Pole weight 67 kg

211 Providing & Fixing of Solderless Crimping Type Aluminium

Lugs (4 Nos. per termination) conforming to IS suitable for 1 x

4.0 Core x 16 Sq. MM PVC Insulated Aluminium Armoured

cable evenly crimped with high pressure tool & connected to 112.00 15.15 No. ₹

switchgear terminals with brass/cadmium plated nut bolts in an

approved manner. - (8 Nos. per St. Light Pole)

212 Providing & erecting 240 V MCB double pole switch for

lighting Load (B Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following

capacity.(A) 6 to 32 Amp. Cat.III - (1 No. Per St. Lght Pole)

213 Providing and erecting Funnel Pipe type earthing having

cms.long and 2.5 cms. dia. galvanised iron pipe with coupling

and buch buried in specially prepared earth pit complete with

necessary 8 SWG earth wire and required size HOT deep 14.00 618.12 Job ₹

Galvanised iron strip for earthing of Street light pole using

proper clamp with using salt and charcoal / coke as required

for pipe type earthing. (1 Job Per St. Light Pole)

214 Providing and erecting Street Light pole bracket comprising

main B Class GI pipe of 4.2 cm/require outside dia. complete

with suitable B Class G.I. sleeve tubing of approx.

45cms.length and suitable for 76.5 mm /80mm / required size

of pole top having sufficient fasteners for fixing the brackets

and having spread of 1.5.mtr. length with 110 deg.with vertical 14.00 683.77 No. ₹

plane & suitable welded stays, reducer and with check nuts

complete painted with one coat of Red oxide / PU base primer

and two coats of Aluminium / PU paint. paint with following

nos of arms. [A] Single Arm Bracket 1.5 Mtr (1 No. Per St.

215 Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 14.00 5976.17 No. ₹

85 %.( fittings required LM-79 & LM-80 certificates)(NOTE:

Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and

,Light must have 440VAC line supply with over-voltage

(iii) Above 60 to 90 watts

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

216 Supplying and erecting Flexible FR PVC insulated multi strand

multi core 1.1 kV grade ISI Marked Copper wires of 2.5 Sq.

MM.,3 core round PVC sheathed in exising pipe/ in street light 126.00 77.77 Mtr ₹

pole erected with green colour for earth continuity.

217 Providing & erecting of 1 x 4.0 Core x 16 Sq. MM, XLPE (IS:

7098 (i) - 88), ISI Mark, Armoured cable, Multistranded

Aluminium Conductor suitable for 1.1 kV grade to be laid on

wall with necessary clamps or to be laid 90 Cms underground

in existing cable trench/ pipe at road crossing or on floor and 490.00 153.52 Mtr ₹

making the ground as per original. - For Streetlight between

two poles & Service Connections.(Considering 25 Mtr.

Distance between two poles and extra cable for loop = 35 Mtr.)

218 Providing & laying of approved make 50 MM outer dia

Doubled Walled Corrugated Pipes (DWC) of polyethylene

(conforming to IS 14930 - II) with necessary connecting

accessories like coupler, Tee, L - Bow, etc. of same material at

required depth (90 cms) for laying of cable below ground/ road 420.00 62.62 Mtr ₹

surface for enclosing cable and back filling the same to make

ground as per original & as per instruction of Engineer

Incharge - for Streelight Cable of 1 x 4 core x 16 Sq. MM. (30

Mtr Per Between two Pole)

219 Providing & laying of approved make 90 MM outer dia

Doubled Walled Corrugated Pipes (DWC) of polyethylene

(conforming to IS 14930 - II) with necessary connecting

accessories like coupler, Tee, L - Bow, etc. of same material at

required depth (90 cms) including excavation for laying of 29.00 95.95 Mtr ₹

cable below ground/ road surface for enclosing cable and back

filling the same to make ground as per original & as per

instruction of Engineer Incharge - for Streelight Cable of 1 x

core x 16 Sq. MM.

220 Drilling the road without breaking the road surface (Asphalt)

for laying of cable for feeding power supply by making up to

100mm dia.size of holes at both ends complete.

221 Making trench in soft soil of suitable width of 90 cm deep for

laying cable or locating the fault all over the run and back

filling the same and making the surface as normal ground.

222 Painting the number and words for inventory Identification on

erected fittings / equipment’s or Such accessories as may

required with good quality of enamelled paint as directed by 14.00 22.22 No. ₹

engineer in charge(i) up to 20 characters, up to 50 mm height.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

223 Smart 4G Timer, Supply of IoT based 4G Smart Streetlight

Control & Monitoring System having a Smart Panel

comprising of 3 Phase IoT Streetlight Smart 4G Timer with

16x2 LCD to display RSSI, relay status, RTC time &

diagnostics., Controller works on 3-phase & also on any

available 1-Phase., Controller with 8-hour battery backup

during external power failure. External power failure alert

immediately to cloud., 110-630 V AC @ 50-60 Hz – 3 phase

operating range., Standby power consumption <3W., Smart 4G

Timer with RS232 port for DLMS Energy meter., Smart 4G

Timer must be compatible with any make / brand of DLMS

(RS232) Energy Meter., DI: 4 Nos. (3 Contactor / Latch

detection, 1 for Door Sensor.)., DO: 3 Relays for Independent

control each phase (R, Y, B) with 1 extra spare relay., Smart

4G Timer with dual SIM functionality for connectivity

backup., 4G M2M SIM 3-Year communication included., 1.00 100427.33 No. ₹

Local configuration via WiFi / BLE for maintenance or during

force majeure., GPS chip inbuilt of Smart 4G Timer for auto

location tracking & astronomic schedule location.,

programmable schedules., Astronomic scheduling with

monthly offsets., Smart 4G Timer has inbuilt timer stores

schedules locally & also stores schedule execution logs locally,

syncs to cloud whenever connected to cloud., Auto-scheduler

overrides manual operations., Monitoring & alerts for MCB

trips., Over/under voltage, current, overload, power factor &

short circuit protections with alerts via Dashboard, App, SMS,

WhatsApp & Email., Contactor / Latch chattering protection &

alerts., Smart 4G Timer with neutral failure protection and

alert., Bulit-in Watchdog for anti-jamming., Smart 4G Timer

must send Regular "heartbeat" on software for CCMS status.,

224 Accelerometer for tamper & panel movement detection &

alerts., Smart 4G Timer must be tested from an NABL Lab for

Surge Test @ 6 KV (IEC 61000-4-5), ESD Test @ 4 KV (IEC

61000-4-2), EFT @ 2 KV (IEC 61000-4-4), Conducted

Emission @ 150 KHz-30 MHz (CISPR11), Damp Heat Test

(40 Deg C @ 95% RH) 2 cycles of 12+12 hours (IS:

(Part 5/Sec.2):1981 latest) with all test passing criteria as

“Temporary degradation or loss of function or performance

which is self-recoverable”., FOTA functionality required for

upgrades., Smart 4G Timer sends & stores online/offline data

of controller & load for lamp burn hours analysis., It stores &

syncs connectivity logs for configuration of network

connections & analytics., PANEL & SWITCHGEAR, The

panel includes a Class 1 DLMS energy meter NABL approved

with 1-2 months of stored data of daily, hourly, monthly, load

survey, instantaneous, events, tamper data & with power events

stored in meter memory for audit purpose., Must monitor V, I,

KWH, KVA, PF, KVAH, etc., Panel made with 2 mm CRCA

sheet with ground mountable stand complete with gland plate,

waterproof glands, earthing bolt., IP55, weatherproof panel

with RAL7035 powder-coated., Smart 4G Timer must be fitted

on removable terminal sockets for easy maintenance.,

Switchgear includes 3 Nos. 3 pole Contactor / Latch having

minimum 50 A Load carrying capacity per phase, all other

switchgear & wires: 40 A load carrying capacity., 1 Nos. 4P

MCB 10 kA for Incomer & 6 Nos. 1P MCBs 10 kA for

Outgoing., Phase-Wise Bypass MCBs required., 4P RCCB

mA., door sensor.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

225 Also, provide lock & key facility., Panel mount outdoor

antenna for GSM, GPS., Canopy design for draining down

water., CCMS SMART SOFTWARE, OAuth 2.0 APIs for

sending data to Government clouds/software, etc., CCMS Web

dashboard with secure password & OTP login., Hosted on

trusted cloud, data security, antivirus & attack protection.,

HTTPS., AES256-bit encryption., Vulnerability Assessment

and Penetration Testing (VAPT) certificate for CCMS

Software., Streetlight management software for load status,

live analytics & reports., Energy meter data tables (kW, kWh,

PF, I, V, etc.) available., Utility monthly bill reconciliation &

Class 1 accuracy reports for billing, energy monitoring &

auditing for streetlight load., Fault detection., Light fault 99%

analysis on dashboard using energy monitoring., WhatsApp

integration., Hierarchy-wise reporting & alerts., GIS mapping

of live connected streetlight control panels, poles &

streetlights., MQTT protocol., Smartphone app with local

configuration & navigation., Monitoring & reporting of

lighting parameters., Facility for media attachments for site

photos/videos/work permits/checklists, etc. per Feeder Panel

for remote verification., Asset management module for

streetlight infrastructure data., Complaint/service task

management with history & escalation must be available.,

Android & iOS App for dashboard analytics, graphs, energy

data, alerts., 3 Years CCMS Web Software & Cloud Server

Hosting subscription included., Customizable, user-friendly

226 Providing & erecting Approved make Four pole moulded case

circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply

c/s. with all internal connections & complete erected in 1.00 6173.12 No. ₹

existing 16 G.M.S. housing. (Cat - III) suitable to work on AC

supply with all internal connection-ICS=100% of ICU only.(1

No. per Distribution Box)

227 Providing & Fixing of Heavy Duty Flange type Double

Compression brass double Compression type Cable Gland with

rubber ring suitable for 1 x 4.0 Core x 16 Sq. MM PVC

Insulated Alu. Armoured cable complete with outgoing tails,

insulating taps etc. - (3 Nos. Glands per distribution box).

228 Providing & Fixing of Solderless Crimping Type Aluminium

Lugs (4 Nos. per termination) conforming to IS suitable for 1 x

4.0 Core x 16 Sq. MM PVC Insulated Aluminium Armoured

cable evenly crimped with high pressure tool & connected to 12.00 15.15 No. ₹

switchgear terminals with brass/cadmium plated nut bolts in an

approved manner. - (12 Nos. Lugs per Distribution Box).

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

229 Supplying & erecting in earthpit of minimum bore dia. 150mm

size approved make Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS 3043-1987 made of corrosion free

hot dipped G.I.Pipes having Outer pipe dia of 50 mm having

80-200 Micron galvanising, Inner pipe dia of 25 mm having

200-250 Micron galvanising, connection terminal dia of

mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for

following type of applications with chamber and heavy duty

cover.(approved make OEM has to submit test certificate

including value of earth resistane of installation.) & having

back filling compound of (B) Inner Chemical (CCm

Compound) - Resistivity :- 0.2 Ohm/meter testing as per IEC

62561-2017 , Voltage Drop :- < 1 volt at no load & dry form

Sulpher content :- <2% .(C) Back filling copound :- Earthing

compound should be capable to retain moisture for log time.

Necessary test report must be submitted.

(C) For Electrical Installation covering Transformer Neutrals,

Lightning arrester Earthing, A.C.Plant & Sensitive

Computer System (like Automation, SCADA) i.e. independent

Earthing located in other than normal soil i.e. Soft Rock,

Marshy Soil etc..-Length of Pipe : 3 Mtrs. -Back filling

Compound :2 nos Bags of 25 Kg.- (1 Job per Distribution

230 Supply & Laying of High Speed Gigabit Ethernet UTP

AWG 250 MHz Class E LHZH Cable, C6 for CCTV.CAT-6 48.00 55.00 Mtr ₹

231 Supply, Installation, Testing & Commissioning of Field

Termination Plug CAT6.

232 Supply & Laying of High Link Fiber Optic, Armoured, Uni

loose Tube Outdoor Cable, Gel filled, Peripheral Steel rod 600.00 80.00 Rmt. ₹

Strength Member, Single Sheath Black HDPE, OS2, 6cores

233 Supply, Installation with splicing, Testing & Commissioning of

Fiber Panel Sliding 2cutout, Adapter Plate Loaded with 6LC

duplex, Expansion Plate for 6LC duplex, 12LCU Pigtails,

Splice Tray, SM, 1U

234 Supply, Installation, Testing & Commissioning of High Link

LCU to LCU Fiber Optic Patch Cord, Duplex, OS2, 3M

235 Supply, Installation, Testing & Commissioning of 24 x

10/100/1000BASE-T PoE ports 4 x Gigabit RJ45/SFP Combo

ports Advanced L2 switching and security features L2+

Static Routing Optional “standard mode” or 1.00 68550.00 Nos. ₹

“surveillance mode” management user interface 193 W PoE

budget [Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

236 Supply, Installation, Testing & Commissioning of

10/100/1000Base-T PoE/ PoE+ ports & 2 Combo 10/100/1000

base-T/SFP ports Layer 2+ swicth. Operating Temperature -40

237 Supply, Installation, Testing & Commissioning of 1G SFP

238 Supply & Installation of 19" 6U,600x450mm IP65 Outdoor

Rack with Front Metal Door, cable entry on Bottom,2 Pairs of

Adjustable 19" Mounting Rails,Full Powder Coated Rigid Steel

Construction with wall/Pole mount provision.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

239 Supply, Installation, Testing & Commissioning of 15U (600W

X 600D)MM Wall mount closed rack with front glass door, fan

tray on top, perforated rear doors, keyboard tray with shelf.

Casters & 2 nos vertical power strip with std. accessories at 1.00 28050.00 Nos. ₹

floor distribution. as per tender specification - 15U-600x600

wall mount indoor rack, front acrylic door, fan-1, pdu 6 socket-

2, cable manager-1, tray-1,mounting hardware-2 pkt

240 Supply, Installation, Testing & Commissioning of 4MP

Network IR Bullet Camera 1/2.9” 4MP PS CMOS Image

Sensor (0.8758cm), H.264+, triple-stream encoding, Max.

lens, WDR(120dB), Day/Night (ICR), 3D DNR, ROI, AWB,

AGC, HLC, BLC, IR Range of 60 Mtrs., Built-in IR LED,

Micro SD Card, Built-in Mic,IP67.

241 Supply, Installation, Testing & Commissioning of 32 ch NVR

with Up to 32 Channel IP camera input, Max. 384 Mbps

incoming/recording/outgoing bandwidth, Instastream, H.265,

H.264+, H.264, MJPEG codec decoding, AI by Recorder:

Channel face detection and recognition, up to 20 face

databases and 20,000 face images, 4 Channel perimeter

protection, 8 Channel SMD Plus, Support 8 SATA HDDs 1.00 43080.00 Nos. ₹

up to 20TB Each, 4 USB Ports (2 front USB 2.0 ports,

rear USB 3.0 ports), AI by Camera: Face detection and

recognition, Perimeter protection, SMD Plus, Metadata,

ANPR, Stereo analysis, Heat map, People counting,

Support RAID 0/1/5/6/10.

242 Supply, Installation, Testing & Commissioning of 8 TB

Survailance SATA-II Hard disk for Recording Storage. 3.00 25850.00 Nos. ₹

243 Supply, Installation, Testing & Commissioning of Hardware

for PC Client (Recommended) , CPU - Intel Core i7, 64 bits

Core Processor , Memory - 16GB , Windows Server 2019 (64-

bit), Graphics Card - GeForce GTX 1060 3GB (Discrete

Graphics Card), Hard Drive Capacity - 200 GB free space for

Client, Ethernet Port - 1,000 Mbps

244 Supply, Installation, Testing & Commissioning of 55" LED

Professional Display, 4K Resolution, 350 CD/M2 Brightness

with 24x7 Application with required Wall Mounting Bracket & 1.00 68580.00 Nos. ₹

HDMI Male to male Cable as per site requirement.

245 Supply, Installation, Testing & Commissioning of Video

Management Software base license. (16-ch Inbuilt)

246 Supply, Installation, Testing & Commissioning of 600 VA

offline UPS for network Rack with 8-10 minute battery 12.00 6850.00 Nos. ₹

247 Supplying, installing, testing and commissioning of 6 KVA

UPS with 30 minute backup.

248 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench / pipe 800.00 69.00 Mtr ₹

of following size of cables. 3C X 2.5 Sq mm ( For CCTV

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

249 LV POWER CONTROL CENTER (PCC)

Supply, installation, testing and commissioning of the LV

Distribution Board (LVDB) of totally enclosed, dust- and

vermin-proof, indoor type construction, fabricated from CRCA

sheet steel having a minimum thickness of 3.0 mm for the base

frame, channels and gland plates, 2.0 mm for load-bearing

members and doors, and 1.6 mm for internal partitions. The

LVDB shall have a minimum degree of protection of IP-52 as

per IS:2147 and shall be suitable for operation on a 3-phase, 4-

wire, 415 V, 50 Hz system with effectively grounded neutral.

The board shall be provided with separate instrumentation

compartments accommodating meters, auxiliary and protective

relays, LED-type indicating lamps and control MCBs

conforming to IS:13947. Current and voltage transformers

shall conform to IS:2705. The LVDB shall be provided with air-

insulated electrolytic-grade aluminium or copper busbars for

three-phase and neutral systems, along with a GI earth bus

running throughout the entire length of the panel. All power

and control wiring shall be carried out using 1100 V grade, 1.00 43614.83 Nos ₹

FRLS insulated copper conductor wires conforming to IS:694

and IS:8130. The panel shall include all necessary equipment

fittings and shall have a horizontally running busbar

compartment with a minimum height of 300 mm. Incoming

and outgoing cable terminations shall be suitable for 1100 V

grade aluminium or copper conductor, XLPE/PVC insulated

and PVC-sheathed armoured cables. The LVDB shall be

provided with the required incoming, bus coupler and outgoing

modules of the specified types and ratings.

Above 80 A, upto & including 250 A, 3 & 4 Pole, Air Break

Fixed MCCB conforms to IS / IEC 60947-2 with trip free

mechanism, current limiting type with Thermal-Magnetic /

Microprocessor release (O / C, S / C & E / F) with adjustable

settings & having minimum 2NO+2NC potential free auxiliary

contacts with all necessary Electro-Mechanical protections &

interlocks etc. MCCB module, when used as Incommer / Bus

Coupler, shall have enclosure dimensions- 1800(H) x 600(W) x

600 (D) & following technical features:

250 4 Pole, 200 A MCCB with Breaking Capacity of Icu=50 KA at

415V (Ics =100% of Icu), Microprocessor release

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

1) Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, Conforms to IS 8623-1 &

3, IEC 61439-1 & 3 without MCB to house appropriate nos. of

MCBs.(The DBs should be used of same company of MCB to

be used) suitable for

(B) three phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI)

(a) Double door

2) Providing and erecting Approved make RCCBs conforming

to IS: 12640 and having sensitivity of 30 mA and Short Circuit

withstand capacity of 10 KA and suitable for operation on

phase and neutral 415V,50Hz. having characteristic of quick

action & tripping with all advance feature & do not incorporate

any electronic component for following Max. rating erected as

(ii) 63Amps. FP - Cat. III, Incomer

3) Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

following capacity

Double pole 6A to 32A Cat.III

Design, Supplying, installing, testing of factory fabricated

ready made Three phase APFC

Panel Cubical Panel fabrication should be type tested as per

IEC 61921, 61439:1&2 Capacitor Duty Contactor for

switching as per following Steps Incomer Switch of MCCB

type Icu=Ics=50KA at 400/440 Volts, with OC, SC, internal

earth fault protection Incomer Switch of MCCB type

Icu=Ics=50KA at 400/440 Volts, with OC, SC, internal earth

fault protection, Copper tinned insulated Busbar,Cubical panel

should be indoor type with IP 43 and IK 10,Metalized

polypropylene film tye3-phase 550Volt Capacitor,De tuning

Reactor for each capacitor,Panel having Short Circuit and

Overload protection, Each step Capacitor having suitable MCB

with Sc, OL, internal earth fault relay,Each stage having

Stage Contactor (Capacitor load rating),PF regulator master

controller having suitable

steps with LCD display, Rs 485 Communication port,

Indication LED Lamps for main incomer and ON-OFF for each

capacitor bank, MS Chanel for Floor mounting, Cable entry as

per site situation,Cooling fans for panel

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

253 SCADA Software

SITC of Licensed SCADA Software (Latest Version) for

Central Monitoring & Control System of 2 Pumping Stations

and street lighting system, including supply, installation,

testing and commissioning of SCADA software capable of real-

time centralized monitoring and control of all units from a

central control room, as well as local monitoring and control

from individual locations. The software shall support seamless

integration with PLCs/RTUs over standard protocols (Modbus

TCP/IP, IEC 60870, etc.) and provide functionalities including

graphical HMI, data logging, alarm management, historical 1.00 1212000.00 Nos ₹

trends, and automated reporting. The license shall support the

required number of tags/nodes and include configuration for

both central and local HMIs. Complete in all respects and with

all required accessories and hardware to run the software and

system including one-year warranty, operator training, OEM

support, and documentation.

1) I5 PC with 8 GB RAM 1TB Hard Disk & 32” Monitor

2) 1 KVA UPS for 1 Hr. Backup

254 PLC Based Control Panel

Supply, Installation, Testing & Commissioning of PLC Based

Instrument control Panel with panel mounted 10 " colour touch

screen HMI, 4G or Latest GPRS modem with ethernet port /

Such suitable port for Remote data transmission to SCADA,

SIM card for remote data tranmission facility, Communication

port for MFM . Instrument Control Panel '(PLC Enclosure /

Panel ) with necessary PLC based logic and wiring , Min.

kVA online UPS (with 30 min backup alongwith filter for 1.00 1027170.00 Nos ₹

harmonic, suitable rating SMF inbuilt batteries alongwith

battery charger and all other accessories as per standard), etc.

complete in all respects and as per specs with PLC having

minimum I/O count of 32DI / 32DO / 16AI /12AO. These are

the minimum IO requirement if any other IO,s required to

complete the work contractor shall be provide the same without

any extra cost.

255 MEDIUM VOLTAGE CABLES

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe of 160.00 1168.57 Mtr ₹

following size of cables

(I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core) For Incomer

to LT Panel & DG to LT Panel

256 (E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core) For APFC

257 (A) 4 core 16 Sq. mm

For all Equipments and PDBs / LDBs

258 CABLE Gland

Providing and, fixing heavy duty flange type brass double

compression type cable gland

with rubber ring for PVC insulated armoured cable complete 4.00 247.45 Nos. ₹

with out going tails, insulating tape etc for following size of

(H) 3 & 1/2 core 240 Sq. mm For Incomer to LT Panel & DG

259 (D) 3 & 1/2 core 95 Sq. mm For APFC Panel 4.00 131.30 Nos. ₹

260 (A) 4 core 16 Sq. mm

For all Equipments and PDBs / LDBs

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with 16.00 85.85 Nos. ₹

brass/cadmium plated nut bolts in an approved manner.

262 F) 95 Sq.mm. For APFC Panel 16.00 40.40 Nos. ₹

For all Equipments and PDBs / LDBs

Providing and fixing approved make Perforated C type cable

tray. Made from sheet steel. The cable tray should be single or

double bended as per required and as per IS 2062/1079 and

shall be coated with hot dip galvanizing as per IS 2629/4759.

with max 17.5% perforation with coupler plate / Fish plate and 160.00 360.57 Mtr. ₹

GI hardware like nut - bolt and washers etc. erection with

necessary support included) as per Specification and as per

instruction of engineer in charge.

(2) 100 X 50 X 1.6 mm Thick

266 CHEMICAL EARTHING SYSTEM

Supplying & erecting in earthpit of minimum bore dia. 225mm

size approved make Safe Earthing Electrode consisting Pipe-in-

Pipe Technology as per IS 3043-1987 made of corrosion free

hot dipped G.I.Pipes having Outer pipe dia of 80 mm having

80-200 Micron galvanising, Inner pipe dia of 40 mm having

200-250 Micron galvanising, connection terminal dia of

mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for 26.00 7095.25 Nos ₹

following type of applications with chamber and heavy duty

cover.(approved make OEM has to submit test certificate

including value of earth resistane of installation.

[B] For Electrical installation up to 11 KV located in other

than normal soil i.e. Soft Rock, Marshy Soil etc.

-Length of Pipe : 2 mtr

-Back filling Compound :1 no. Bag of 25 Kg.

(Each for MPDBs, PDBs, Motors etc.)

267 Providing and erecting required size HOT deep Galvanised

iron strip for earthing of Transformer LT panel board, Motors

etc. using proper clamp.

(50X6 G.I Strip wt.2.4 kg/m, 2.4x260 Mt.= 624kg.)

268 Providing and erecting required size HOT deep Galvanised

iron strip for earthing of Transformer LT panel board, Motors

etc. using proper clamp.

(25X3 G.I Strip, 0.6 Kg/m, 0.6x 130Mt.=312Kg.)

269 Providing and erecting HOT deep Galvanised iron strip wire

(8 SWG G.I Strip, 0.103 Kg/m, 0.103 x 100Mt.=10 Kg)

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

270 Point wiring for FAN with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected with 6A Modular type switch

and hum free EME step type electronic fan regulator mounted

and accessories with earth continuity of following type erected

on PVC / Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate modules 4.00 674.68 Pt ₹

erected on / in wall / ceiling as per pipe erected. with necessary

ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling

271 Point wiring for Light / Bell with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to

mtr length , in below type of pipe erected with 6A Modular

type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured/metallic/white 30.00 485.81 Pt ₹

front plate modules erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling

complete - Cat. III

272 Point wiring for Two Way Controlled Light Point with 2-1.5

sq.mm & earth wire of 1.5 sq.mm (green) both are of .ISI

marked 1.1 KV grade FRLS PVC insulated multi strand copper

wires erected in below type of pipe with 6A Modular type

switches and following type of accessories erected on PVC /

Metallic/Wooden box, single mounting base frame covered

with textured / metallic/white front plate modules erected on / 2.00 603.98 Pt ₹

in wall / ceiling as per pipe erected. with necessary

batten/angle holder or ceiling rose or H.D.Connector as

(f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling

complete - Cat. III

273 Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected complete with Modular type

switch & 5 pin Plug erected on PVC / Metallic/Wooden box

covered with appropriate front plate modules erected on / in

wall / ceiling as per pipe erected with following type of 2.00 871.63 Pt ₹

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu.

Wire with 2.5 sq.mm ( green) earthing wire from mcb d b

(f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling

complete (For AC)

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

274 Point wiring for independent PLUG with following size mains

earth wire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires upto

mt length, in following below of pipe erected complete with ISI

marked 3 / 5 Pin socket and tissino type switch erected with

earth continuity connection erected on Metal / PVC/Wooden

box covered with 3 mm thick PC(Polycarbonate) /

Acrylic/Laminated sheet. 20.00 347.44 Pt ₹

[A] For 6 amp plug and 6 amp switch with 2-1.5 sq. mm Cu.

Mains from near by switchboard/db

board upto 6 mt.

(f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling

275 Point wiring for independent PLUG with following size mains

earth wire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires upto

mt length, in following below of pipe erected complete with ISI

marked 3 / 5 Pin socket and tissino type switch erected with

earth continuity connection erected on Metal / PVC/Wooden

box covered with 3 mm thick PC(Polycarbonate) / 10.00 530.25 Pt ₹

Acrylic/Laminated sheet.

[B] 6/16A Plug and 16 amp switch with 2-2.5 sq. mm Cu.

Mains from mcb d b boards.

(f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling

276 Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected with necessary connections as per site 40.00 151.50 Nos ₹

situation directed by Engineer In charge.

(1)One No. SP 6 Amp. - Cat.III

277 (2) One No 5 pin plug - Cat.III 20.00 151.50 Nos ₹

278 (5) Electronic hum Free steps EME Fan regulator - Cat.III 4.00 398.95 Nos ₹

279 (8) Computer RJ-45 socket 5.00 160.59 Nos ₹

280 (9) 16 Amp. SP one way switch 2.00 180.79 Nos ₹

281 (10) 6/16Amp. Universal socket 2.00 199.98 Nos ₹

282 (12) 6Amp. / 16 Amp. Two Way switch 4.00 170.69 Nos ₹

283 Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed on

wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC 250.00 82.82 Mtr ₹

insulated stranded wire of green colour for earth continuity of

(A) With medium class Rigid PVC pipe and accessories

(c) 3 wire 1.5 sq. mm - For Internal Lights

284 (d) 3 wire 2.5 sq. mm

For Ceiling Fan

285 providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling with

2.5 sq. mm copper conductor FRLS PVC insulated stranded 150.00 142.41 Mtr ₹

wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(d) 3 wire 4 sq. mm - For ACs

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

286 Supplying & erecting approved make low noise decorative

exhaust fan having square frame ABS body with inbuilt lowers

& square frame.

250mm with 1350 RPM Cat.II

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/aluminium pressure die

cast powder coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with company

160V to 270V,Power Factor more than 0.9, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt , 24.00 589.84 Nos ₹

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount

Downlight with provision for spring loaded mounting clips

(iii) 20 watts, Surge-2 KV - Cat-lll

288 LED LIGHT FIXTURES & LIGHTING:

Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or

embossed 160 to 270 V, Power Factor more than 0.95, THD <

10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, 8.00 5194.43 Nos ₹

Luminaire efficacy> 100 lumens/watt . LED driver efficiency >

85 %.( fittings required LM79 & LM-80 certificates)(NOTE:

Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)

(B) Flood Light (IP-65), Surge protection -4KV integral and

,Light must have 440VAC line

supply with over-voltage protection. 40W LED - Cat-iii

289 Ceiling Fan

Providing & erecting Approved make Power Saving 50 Watt

Ceiling Fan with double ball bearing ISI mark with Condenser

230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades

with aluminium blades with , canopy & 30 cm. down rod 4.00 2311.89 Set ₹

erected with earthing.(Make shall be approved by Engineer in

charge)) Fan shall be painted with white colour.

2 Nos for Pump House

290 Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan

complete with proper insulation without leakage and earthing.

1 Meter Down Road or as per instruction given by engineer

291 Supplying & erecting Fan Hook of 10 mm M.S. Round bar

grouted in RCC slab with Making the site as original.

REDEVELOPMENT OF HAJIYANI BAUG DUMPING SITE MODERN WASTE MANAGEMENT

INFRASTRUCTURE FOR JUNAGADH

No. Description Quantity RATE Unit Amount

292 Supplying & erecting fan hook box of 10 mm M.S. round bar

bounded to the RCC bars up to 50mm length each side and

pierced through a 16 Gauge M.S. box / Heavy Duty PVC box 4.00 108.07 Each ₹

complete erected concealed in Ceiling with necessary

293 Providing Fan clamp of 30 x 5 mm flat of required length &

10 mm M.S. Bolt & Nuts erected with necessary hook of 10 4.00 98.98 Each ₹

mm M.S. Round Bar.

294 Providing & Erected 2.5mm.thick laminated acrylic sheet to

cover the fan hook or Fan box.

295 SAFETY ACCESSORIES

Supplying & erecting carbon dioxide (CO2) fire extinguisher

user of following capacity with necessary clamps made from

50 x 6 mm M.S. Flat with nut & bolts grouted in wall

[B] For 5.5 / 6.5 KG Capacity

296 Supplying and erecting floor mounting stand for keeping four

nos. of FIRE buckets comprising 1500 mm in length, 900 mm

height frame made out of 30mm X30 mm X 4 mm angle iron

with cross supports for legs, welded with 4 hooks and duly

painted with one coat of red lead and two coats of approved

enamelled silver paint.

297 Supplying stand first AID box with anticeptic cream,

medicine for use on wounds due burn, crepe bandage, guage

bandage, medicated ready to use bandage (Band-aid) adhesive

tape for medicinal user, scissors, anticeptic solution (Savlon or

similar) etc. (All above contents shall be of standard makes)

298 Providing and fixing printed instruction chart both in English

and Gujarati and duly framed with front glasses, for treatment

of person suffering from Electric shock with minimum 50"

diagonally size.

299 Supplying rubber matting of following thickness as per

300 MISCELLANEOUS:

Providing , erecting , fabricating the M.S. structure as per

requirement on site incorporating proper size of M.S.

angles,square,round, flats, bars, channels, sections complete 500.00 77.77 kg ₹

with cutting, welding, grinding & finishing duly painted with

one coat of red oxide with erection on site as per direction of

engineer in charge with necessary grouting, cementing,

plastering & finishing complete.