CONSTRUCTION OF BLOCK-CUM-CIRCLE OFFCIE BUILDING AT MOTIHARI BLOCK IN THE DIST EAST CHAMPARAN FOR THE YEAR-2025-26.

Earth work in excavation over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m; disposal earth to be levelled and neatly dressed.

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Extra for every additional lift of 1.5 m or part thereof in

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth : consolidating each deposited layer by ramming and watering lead.

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead.

Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering-all work upto plinth level.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

1:3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

1.4.8 (1 Cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufacturers.

Centring and shuttering including strutting, propping etc. and removal of form for :

Metre

Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc, including cost of de-shutering and de centring at all levels over a height of 3.5 m, for every additional height of 1 meter of part thereof (plan area to be measured)

Reinforcement for RCC work including straightening. Cutting, bending, placing in position and binding all complete.

TMT-500- 8mm dia .

TMT-500-10 mm dia.

TMT-500-12 mm dia

TMT-500-16 mm dia.

TMT-500-20 mm dia.

TMT-500-25 mm dia

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grde reinforcd cement concrete

All work upto plinth level

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- All work up to plinth level :

Reinforced cement conrete work in beams,suspended floors, roofs having slope upto 15, landings,balconiec, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excludingthe cost of centring, shuttering, finishing and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm nominal size).

Brick work with bricks of class designation 100A in foundations and plinth in:

Cement mortar 1:4 (1 Cement :4 coarse sand)

Brick work with bricks of class designation 100A in foundations and plinth in :

Cement mortar 1:6 ( 1 cement: 6 coarse sand)

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work

Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work

Extra tor Brick work in superstructure above plinth level upto floor V cum

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Cement mortar 1:4 ( 1 cement: 4 coarse sand)

Providing and fixing flush door shutters conforming to IS : 2202 (Part-I) non-decorative type.core of block board construction with frame of 1st class tiard wood and well mathched commercial 3 ply veneering wiih vertical grains or cross bands and face veneers on both faces of shutters.

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (Over all area of door shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:

Metre

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mmdia ( heavy type ) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Providing and fixing teak wood lipping of size 25x3 mm in pelmet.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C.doors) using synthetic rubber based adhesive.

Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - incharge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100 x 89 x 3 mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-in- charge. The glass shall be clear, toughened, interlayered, non-wired fire resistant having 11 mm thickness of approved brand with 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 15 min of insulation (EI15) and having a sound reduction of ?37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category of Impact Resistance as per EN 12600. The glass should be manufactured in UL & TUV audited Facility and including UL-EU Certification.The maximum glazing size cannot be more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report for the complete system (Glazed Door or Partition) will be considered valid only if it contains the stamp and signature of the authorized signatory from the glass manufacturer. (Actual glass size is to be measured at site for payments).

Providing and fixing pressed steel door frame confirming IS code 351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-Charge.

Metre

Providing and fixing circular / hexagonal cast iron or M.S. sheet box for ceiling fan clamp 140 mm internal dia 73 mm height, 5 mm thick rim bottom and top lid , 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the comers. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up section/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-iron 40x40x6 mm with 40 mm dia steel pulleys complete with bots. Nuts locking arrangement stoppers handles including applying a priming coat of approved steel primer

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.).

Aluminium Works Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / neling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings, the aluminium quality as per grade 6063 T5 or T6 as per BS 1474, including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-charge. (The item includes cost of fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account)

Designing, fabricating , testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the buildings for all heights and all levels,including

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I.

Providing designation 100 A one brick on edge soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength,thickness & size/shape, made by table vibratory method , to attain superior smooth finish using PU or equivalent moulds, laid in required Grey colour & pattern over 50mm thick compacted bed of coarse sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks,lawns, drive ways or light traffic parking etc. all complete as per manufacturer’s specifications & direction of Engineer -in-Charge:

Providing and laying polished Granite stone flooring in required design and patterns , in linear as well as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average ) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slury and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer -in-charge.

Stone tile (polished) work for wall lining over 12 thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and cement slurry @ 3.3 kg / sqm including pointing in white cement complete

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Providing and laying Vitrified in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with notch towel, piler, wedge, clips of required thickness, leveling sysem and rubber mallet for placing the tiles gently and easily

Glazed Vitrified tiles Matt / Antiskid finish of size

Size ot tile 600 x 600 mm

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Motar 1:3 (1cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) /1:4 (1 cement : 4 coarse sand)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with :

Extra for Kota stone / sand stone in treads of steps and risers using single up to 1.05 metre.length

Extra for pre finished nosing in treads of steps of Kota stone / sand stone slab.

Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc.

Providing edge moulding to 18 mm thick marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in Charge

metre

Cement plaster in Coarse Sand

12 mm cement plaster of mix

15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall.

18 mm cement plaster in two coat under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand finished rough with sponge.

6 mm cement plaster to ceiling of mix.

12 mm cement plaster of mix

1:3 (1 cement:3 coarse sand)

6 mm cement plaster to ceiliing of mix :

1:3:(1 cement : 3 fine sand)

Neat Cement punning

Applying one coat of cement primer of approved brand and manufacture on wall surface :

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:

Distempering with 1st quality washable distemper (ready made) of approved manufacture and of required shade and colour complete. As per manufacture's specifications.

Two or more coats on new work

Cement primer

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

New work ( three or more caots)

Applying priming coat:

With ready mixed red oxide zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shed.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Forming groove of uniform size from 12 x 12 mm and upto 25 x 15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-charge.

Stone work (machine cut edge) for wall lining etc. (veneer work) over 12 mm thick bed of cement lime mortar 1:1:6 (1cement : 1 lime putty : 6 fine sand) including pointing in white cement mortar 1:2 (1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of cramps which shall be paid for seperately)

Providing and fixing gun metal cramps of required shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 fine sand) including making the necessary chases.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part there of

Extra for plastering :

Finishing walls with Premium Acrylic smooth exterior paint with silicone additives of required shade.

New work (Two or more coats applied @ 1.43 ltr / 10 sqm. Over and including base coat of water proofing cement paint applied @ 2.20 kg / 10 sqm).

Finishing walls with textured exterior of required shade :

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.

IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.

IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm

Providing and Laying APP (Atactic Polypropylene polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre /sqm by the same membrane manufacture of density at 250 C, 0.87-0.89 kg / litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The Vital physical and chemical parameters of the membrane shall be as under : Joint strength in logitudinal and transverse direction at 230 C as 650/ 450N / 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 1500C. Cold flexibility shall be upto -20C when tested in accordance with ASTM, D-5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Grading roof for water proofing treatment with

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing plinth protection 750 mm wide consisting of 12 mm thick cement plaster 1;6 with neat cement punning over 75 mm thick P.C.C. (1:3 :6) over brick flat soling over 75 mm thick local sand filling all complete

Providing plain cement concrete in (1:2:4) including making grooves laid in pattern of tiles 300 x 300 mm avg. thickness 40 mm on sloped roof as per drawings all complete.

Making khurras 45 x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400micron, finished with 12mm cement plaster 1:3 (1cement:3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos / Lindane emulsifiable concentrate of 20%.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termites' treatrnent (including the cost of chemical emulsion)

Along external wall where the apron is not provided using chemical imulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete.

Metre

Along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.

Metre

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floor.

Providing and fixing sheet covering over expansion joints with iron screws as per design to match the colour / shade of wall treatment.

metre

Providing and filling in position bitumen mix filler of Proportion 80 kg of hot bitumen, 1 kg of cement and 0.25 cubicmetre of coarse sand for expansion joints.

Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Supplying and fixing C.I. cover without frame for manholes

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design

560 mm diameter C.I. over (heavy duty) the weight of the cover to be not less than 108 kg.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

Providing and fixing vent pipes :

Providing and fixing in position 25mm diameter mosquito proof coupling of approved municipal design

Providing and fixing C.I. sluice valves (with cap) complete with bolts,nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :

Clearing jungle including uprooting or rank vegetation, grass, brush wood, trees and scaplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooring trench with water (excluding cost of imported earth, sludge or manure)

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Supplying and stacking at site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Mixing earth and sludge or manure in proportion specified or directed.

Spreading of sludge, dump manutre or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately)

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rought dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free form weeds and fit for moving including supplying good earth if needed.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m dia. And 1.2 m deep.

Holes 60 cm dia. And 60 cm deep.

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Providing and stacking of Bauhinia blakeana (Kachnar) of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia biflora of height 90-105 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 90-105 cm. bushy in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Mussaenda erythrophylla (Rosea) of height 60- 75 cm. multi branched in earthen pots of size 25 cm as per direction of the officer-in-charge.

Bricks (Lead - 1 km kutcha + 7 km pucca)

Coarse Sand (Lead-160 Km) from koilwar

Stone Chips (Lead - 58 Km) from Chakiya Rack

Local sand (1 km kutcha + 2 km pucca)

Earth (1 km kutcha + 2 km pucca)

Cement

Bricks

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including, cutting and making good the walls etc. (internal work)

Metre

Metre

Metre

Metre

Metre

Metre

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :

Metre

Metre

Providing and fixing brass stop cock of approved quality (screwed end).

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end).

Providing and fixing gun metal non-return valve of approved quality (screwed end)

Providing and fixing P V C connection pipe with brass unions.

Providing and fixing C.P. brass shower rose 15 or 20 mm inlet.

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :

Metre

Metre

Metre

Metre

Metre

Metre

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc.complete (new work)

Providing and fixing C.P. brass,bib cock of approved quality conforming to IS : 8931

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS stamdards and weighing notless than 690 gms.

Providing and fixing C.P brass stop cock (concealed) of standard design and of approved mark conforming to IS:8931

Providing and fixing C.P brass angle valve for basin mixer and gyser points of approved quality conforming to IS: 8931

Providing and fixing PTMT Soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Cutting holes up to 30 x 30 cm in walls including making good the same:

Cutting holes up to 15 x 15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) including finishing complete so as to make it leak proof.

Making holes up to 20 x 20 cm and embedding pipes upto 150 mm in diametre in masonary and filling with cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) including dispopsal of malba.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fittings complete.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing soil, waste and vent pipes

Metre

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),including cost of cutting holes and making good the walls etc. :

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick bolts and nutts complete

Providing and fixing plain bend of required degree

Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts & nuts complete

Providing and fixing single equal plain junction of required

Providing and fixing terminal guard

Providing lead caulked joints to sand cast iron/ centrifugally cast (spun) iron pipes and fittings of diameter

Providing and fixing trap of self cleaning design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work :

metre

Providing and fixing on wall face unplasticised PVC (working pressure 4 kg per sqcm) rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

Metre

Providing and fixing on wall face unplasticised PVC moulded fittings / accessories for unplasticised-PVC rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

Providing and fixing unplasticised-PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S screws or required length including cutting brick work and fixing on cement mortar (1:4) 1 cement:4 coarse sand and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diametre and weighing not less than 440 grams.

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required :

Providing and fixing white vitreous china pedastal type water closet (European type W.C pan) with seat and lid, 10 litre low level white P.V.C flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 410 x 265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions G.I. clamps, complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C.automatic flushing cistern, with fittings, standard size G.I. / PVCflush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required :

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone finished smooth.aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and

Providing and fixing PTMT liquid soap container 109 mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200mm wide with a minimum distances of 37mm fromwall face with concealed fittings arrangement of approved quality, and colour, weighing not less than 88 gms.

Cutting chases in brick masonry walls for following diameter sand cast iron / centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement: 3 coarse sand : 6 graded stonea agregate 12.5mm nominal size) including necessry plaster and pointing in cement mortar 1:4 ( 1 cement: 4 coarse sand):

Metre

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :

Metre

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes inlcuding bed concrete as per standard design.

Metre

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc . (external work)

Providing and fixing gun metal non-return valve of approved quality (screwed end)

50 mm nominal bore

Painting G.I. pipes and fittings with two coats of anticorrosive bitumastic paint of approved quality :

meter

meter

Providing & filling sand of grading zone V or coarser grade all-around G.I. pipes in external work.

Metre

Metre

Providing and fixing Brass bib cock of approved quality.

Providing and fixing brass stop cock of approved quality .

Constructing masonry Chamber 30 x 30 x 50 cm inside, in brick work in cement mortar 1:4( 1 cement: 4 coarse sand) for stop cock, with C.I surface box 100 x 100 x 75 mm(inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) i/c necessary excavation, foundation concrete 1:5:10( 1 cement: 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3(1 cement: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:

Constructing masonry Chamber 60 x 60 x 75 cm inside, in brick work in cement mortar 1:4(1 cement: 4 coarse sand) for sluice valve, with C.I surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) i/c necesary excavation, foundation concrete 1:5:10( 1 cement: 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3( 1 cement: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:nt complete as per standard design.

Providing and fixing square-mouth S.W gully trap class SP-1 complete with C.I grating brick masonry chamber with water tight C.I cover with frame of 300 x 300 mm size(inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

Providing and laying non-pressure NP2 class (light duty) R.CC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2( 1 cement: 2 fine sand) including testing of joints etc. complete.

Metre

Metre

Excavating trenches of required width for pipes cables, etc, including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil , and then returning the soil as required , in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed , within a lead of 50 m.

Pipes, cables etc. ecceeding 80 mm dia . But not exceeding 300mm dia.

Constructing brick masonry manhole in cement mortar 1:4(1 cement: 4 coarse sand) with R.C.C top slab with 1:2:4 mix (1 cement:2 coarse sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand:8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design:

metre

Constructing brick masonry chamber for underground C.I inspection chamber and bends with bricks in cement mortar 1:4( 1 cement: 4 coarse sand) C.I cover with frame (light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38 kg(weight of cover 23 kg and weight of frame 15 kg) R.C.C top slab ith 1:2:4 mix ( 1 cement: 2 coarse sand:4 graded stone aggregate 20mm nominal size) foundtion concrete 1:5:10( 1 cement: 5 fine sand:10 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Extra for depth beyond 45 cm of brick masonry chambar For 455x610 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Providing 150mm wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron concrete (1: 4:8), over one brick designation 100-A flat soling in proper grade and slope at the base, the drain duly plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

metre

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe,removable as per requirement, all complete for borewell of:

Gravel packing in tubewell construction in accordance with IS:4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

metre

metre

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation,refilling the earth or cutting of wall and making good the same complete wherever required :

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

metre

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer - in-charge.

Supply fixing 2 HP Motor Pump (1 Unit) with 32 mm dia clamp (1 Unit), Suitable Length of cable, Panel Board & Starter (1 No.), centre Guide ( 6 Nos.) Machine Up and Down etc. all complete

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools,plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.

metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

metre

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-incharge.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

METRE

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside)with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Modular desk based system of ht. 1200 mm. Cube legs are fabricated by Argo Shield & have a rectangular shape. Cube legs are available for work top level 750 mm from base. Wire Management Single Power box with raiser for Manager Modules, Single tables (8+3 Anchor Roma). Soft closing access flap with brush. Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR Screen: 18mm thk T mold Fabric screen on studs is providing on table top of ht. 450 mm. Worktop: 25mm thk prelaminated partical board with pvc lipping.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing and placing desk based modular workstation with size 900x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. Removable screen and to be used as divider screen. It has a die cast fixing clamp to enable mounting of the screens to the worktop, LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground.

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

Supplying and placing in position office table of the following specifications. 1500W X 600D X 750H Worktop-Made of 25mm Thick Pre-laminated board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Legs-Cube legs are fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) are welded for fixing worktop. These are welded together by argo shield welding. This welded structure is coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert is fixed, on to which a straight M8 leveler fitted which allows for adjustment of the height upto 50mm. Cross Members-Cross Members in Unitised T-2 Desk Series are made from 50mm X 25mm X 1.2mm thick ERW tube (as per IS:7138). These are coated with 50 micron epoxy polyester coating. Cross Members are assembled by friction fit PDC joinery and grub screws. There are always two cross members for one table. Access Flap-Soft closing access flap is used in Unitized T-2 Desk Series. Provision for standard size of 8 module electrical (Anchor Roma) is offered. Access flap is made from Aluminum extrusion, PDC parts made from Aluminum Alloy and plastic parts are made from Nylon 6 and wire brush with nylon bristles. Power Box-Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8 Module cutout provision for Anchor Roma). This is fixed with worktop along the depth at Access Flap position This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Providing and placing desk based modular workstation with size 1200x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. No screen to be used as divider screen. LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. Pedestals with legs - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. CPU trolley - with castors, KBPT with mousetray - Metal

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

Supplying and placing in position Main table of the following specifications. The Main table shall be of size 1800 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm.

Supplying and placing in position Back unit of the following specifications. The Size of the Back unit shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Providing, supplying and placing of Visitor Chair.CHAIR UPPER STRUCTURE: It is a single shell 1.2 ±0.1cm. thick hot pressed plywood with moulded polyurethane foam on top & backing foam on rear side. It is upholstered with option of knitted & leatherette fabric.The seat has extra thick foam on front edge to give comfort to popliteal area.The foam backing done in back ( Executive chairs only) for extra fluffiness and comfort in chair. 2SEAT & BACK HIGH RESILIENCE (HR) POLYURETHANE FOAM :The HR polyurethane foam for seat and back is moulded with density 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 at 25% compression. M.S. VISITOR TUBULAR FRAME (For Thrill Visitore chair): The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. ARMRESTS:The armrest top is moulded from polyurethane(PU) with metal insert and mounted on to a tubular frame. WIDTH (W): 60.5 CM. DEPTH (D): 65.0 CM. HEIGHT (H): 86.5 CM. SEAT HEIGHT (SH): 46.0 CM. This product should be certified by Greenguard

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications. The Main table shall be of size 1800 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm.

Supplying and placing in position Back unit of the following specifications. The Size of the Back unit shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Providing, supplying and placing of Visitor Chair.CHAIR UPPER STRUCTURE: It is a single shell 1.2 ±0.1cm. thick hot pressed plywood with moulded polyurethane foam on top & backing foam on rear side. It is upholstered with option of knitted & leatherette fabric.The seat has extra thick foam on front edge to give comfort to popliteal area.The foam backing done in back ( Executive chairs only) for extra fluffiness and comfort in chair. 2SEAT & BACK HIGH RESILIENCE (HR) POLYURETHANE FOAM :The HR polyurethane foam for seat and back is moulded with density 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 at 25% compression. M.S. VISITOR TUBULAR FRAME (For Thrill Visitore chair): The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. ARMRESTS:The armrest top is moulded from polyurethane(PU) with metal insert and mounted on to a tubular frame. WIDTH (W): 60.5 CM. DEPTH (D): 65.0 CM. HEIGHT (H): 86.5 CM. SEAT HEIGHT (SH): 46.0 CM. This product should be certified by Greenguard

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications.1650x750x750 Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Understructure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side,Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications.1650x750x750 Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Understructure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestal is provided with lock for security This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side, Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Reception table of the following specifications. Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap along with a Gromett is provided on work surface for wire management Wire Management - Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma) which is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. **Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. Length - 2400mm Depth - 1770,870mm Height - 1080mm This product should be certified by GREENGUARD & Indoor Advantage GOLD.

Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressed plywood measured. upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: ·360° revolving type. · Upight position locking · Tilt tension adjustmen. ·Seat/back tilting ratio of1:3. TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY : The bellow is 3-piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33%glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-centre dia. (76.3 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. Overall Dimensions of Chair WIDTH (W): 76.3 CM. DEPTH (D): 76.3 CM. HEIGHT (H): 85.5-97.5 CM. SEAT HEIGHT (SH): 42.5-54.5 CM. This product should be certified by Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of Sofa Overall Size : Width : 175cm Depth : 87cm Height : 76cm Seating Height : 39.5cm STITCHING: THREAD : Poly Proplin. LEATHER/PVC/FABRIC: PVC. Thickness (mm) : 0.9 Weight (GSM) : 575

Providing, supplying and placing of Sofa Overall Size : Width : 134cm Depth : 87cm Height : 76cm Seating Height : 39.5cm STITCHING: THREAD : Poly Proplin. LEATHER/PVC/FABRIC: PVC. Thickness (mm) : 0.9 Weight (GSM) : 575

Providing, supplying and placing of Coffee Table Overall Size : W x D x H - 1000 x 600 x 430mm. 1. Understructure: Legs, top wooden frame & bottom tie members are made out of first quality rubber wood without knots & defects on all faces. Bottom tray is made of 1.2mm thick MS sheet. Metal brackets are used for assembly purpose. 2. Top: 8mm thick toughened glass. 3. Construction: Knock-down assembly. 4. Finish: Bloom_coffee table is in two colour finish option - ÿ Option - 1 : Natural finish ÿ Option - 2 : Walnut finish Wooden members are PU painted with hardness-2H. Metal components are powder coated. Bottom MS metal tray is having floral pattern laser-cut. Top glass is having sand blasted floral pattern on bottom surface. 5. Hardware: Knock-down assembly with high quality standard hardware like screws, metal inserts, wooden dowel, plastic leg bush etc..

Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressed plywood measured. upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: ·360° revolving type. · Upight position locking · Tilt tension adjustmen. ·Seat/back tilting ratio of1:3. TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY : The bellow is 3-piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33%glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-centre dia. (76.3 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. Overall Dimensions of Chair WIDTH (W): 76.3 CM. DEPTH (D): 76.3 CM. HEIGHT (H): 85.5-97.5 CM. SEAT HEIGHT (SH): 42.5-54.5 CM. This product should be certified by Indoor Advantage GOLD & GREEN PRO.

Supplying and placing in position Reception table of the following specifications. Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Wire Management - Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma). This is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. **Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. Length - 1500mm Depth - 870mm Height - 1080mm This product should be certified by GREENGUARD & Indoor Advantage GOLD.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main Table & ERU of the following specifications.1650x1650x750 Primary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel:Made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.understructure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.integrated pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications. The Main table shall be of size 1800 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm.

Supplying and placing in position Back unit of the following specifications. The Size of the Back unit shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Providing, supplying and placing of Visitor Chair.CHAIR UPPER STRUCTURE: It is a single shell 1.2 ±0.1cm. thick hot pressed plywood with moulded polyurethane foam on top & backing foam on rear side. It is upholstered with option of knitted & leatherette fabric.The seat has extra thick foam on front edge to give comfort to popliteal area.The foam backing done in back ( Executive chairs only) for extra fluffiness and comfort in chair. 2SEAT & BACK HIGH RESILIENCE (HR) POLYURETHANE FOAM :The HR polyurethane foam for seat and back is moulded with density 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 at 25% compression. M.S. VISITOR TUBULAR FRAME (For Thrill Visitore chair): The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. ARMRESTS:The armrest top is moulded from polyurethane(PU) with metal insert and mounted on to a tubular frame. WIDTH (W): 60.5 CM. DEPTH (D): 65.0 CM. HEIGHT (H): 86.5 CM. SEAT HEIGHT (SH): 46.0 CM. This product should be certified by Greenguard

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main Table & ERU of the following specifications.1650x1650x750 Primary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel:Made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.understructure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.integrated pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side,Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Modular desk based system of ht. 1200 mm. Cube legs are fabricated by Argo Shield & have a rectangular shape. Cube legs are available for work top level 750 mm from base. Wire Management Single Power box with raiser for Manager Modules, Single tables (8+3 Anchor Roma). Soft closing access flap with brush. Metal modesty: Metal modesty is made from 0.8 mm thick CRCA. Metal modesty are mounted on the worktop with the help of the modesty mounting brackets made of 3 mm thick HR Screen: 18mm thk T mold Fabric screen on studs is providing on table top of ht. 450 mm. Worktop: 25mm thk prelaminated partical board with pvc lipping.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing and placing desk based modular workstation with size 900x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. Removable screen and to be used as divider screen. It has a die cast fixing clamp to enable mounting of the screens to the worktop, LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. CPU trolley - with castors, KBPT with mousetray - Metal

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

Providing and placing desk based modular workstation with size 1200x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. No screen to be used as divider screen. LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. Pedestals with legs - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. CPU trolley - with castors, KBPT with mousetray - Metal

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

Providing and placing desk based modular workstation with size 900x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. Removable screen and to be used as divider screen. It has a die cast fixing clamp to enable mounting of the screens to the worktop, LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. CPU trolley - with castors, KBPT with mousetray - Metal

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

Supplying and placing in position Main Table & ERU of the following specifications.1650x1650x750 Primary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel:Made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.understructure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.integrated pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side,Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main Table & ERU of the following specifications.1650x1650x750 Primary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel:Made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.understructure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.integrated pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side,Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main Table & ERU of the following specifications.1650x1650x750 Primary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel:Made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.understructure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.integrated pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side,Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing and placing desk based modular workstation with size 900x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. Removable screen and to be used as divider screen. It has a die cast fixing clamp to enable mounting of the screens to the worktop, LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. CPU trolley - with castors, KBPT with mousetray - Metal

Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are FULL BACK SIZE 51.5 cm. (W) x 69.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 101.5-111.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Supplying and placing in position Main Table & ERU of the following specifications. Its size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. ERU size shall be 1050 Width x 450 Depth x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading. Supplying and placing in position Free Standing Pedestal of the following specifications with Overall Dimensions shall be 390mm(W)x440mm(D)x646mm(H). The construction & Material used shall be welded assembled , 0.8 mm thick CRCA for body shell , drawer front & tray , front side stiffener ,rear aide stiffener and 1.2 mm thick CRCA Top stiffener & Bottom stoffener . The drawer fronts shall be metal front straight edge . Locking shall be 10 lever cam lock & Central RH locking with actuator & lock channel mechanism for box-box-file Pedestal . The top panel shall be metal straight edge top . Castor should be swiveling non - lockable castors mounted below the body shell for free standing full height mobile pedestal and M8 Leveling stud for free standing pedestal . The anti-tipping mechanism shall have fifth roller arrangement mounted below file drawer to avoid toppling of unit when file drawer is pulled out . Partition in drawer shall be 1 no. Partition in box drawers with lock mounted . Plastic pencil tray shall be optional accessory . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Application shall be suitable for pushing below work surface which has got a clear height of 725 mm from below . For drawer pulling side wise tapered recess provided in shell behind drawer fronts . This product should be certified by GREENGUARD.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications. The Main table shall be of size 1800 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm.

Supplying and placing in position Back unit of the following specifications. The Size of the Back unit shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Providing, supplying and placing of Visitor Chair.CHAIR UPPER STRUCTURE: It is a single shell 1.2 ±0.1cm. thick hot pressed plywood with moulded polyurethane foam on top & backing foam on rear side. It is upholstered with option of knitted & leatherette fabric.The seat has extra thick foam on front edge to give comfort to popliteal area.The foam backing done in back ( Executive chairs only) for extra fluffiness and comfort in chair. 2SEAT & BACK HIGH RESILIENCE (HR) POLYURETHANE FOAM :The HR polyurethane foam for seat and back is moulded with density 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 at 25% compression. M.S. VISITOR TUBULAR FRAME (For Thrill Visitore chair): The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. ARMRESTS:The armrest top is moulded from polyurethane(PU) with metal insert and mounted on to a tubular frame. WIDTH (W): 60.5 CM. DEPTH (D): 65.0 CM. HEIGHT (H): 86.5 CM. SEAT HEIGHT (SH): 46.0 CM. This product should be certified by Greenguard

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing and placing desk based modular workstation with size 900x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. Removable screen and to be used as divider screen. It has a die cast fixing clamp to enable mounting of the screens to the worktop, LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. CPU trolley - with castors, KBPT with mousetray - Metal

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Providing, supplying and placing of Visitor Chair.CHAIR UPPER STRUCTURE: It is a single shell 1.2 ±0.1cm. thick hot pressed plywood with moulded polyurethane foam on top & backing foam on rear side. It is upholstered with option of knitted & leatherette fabric.The seat has extra thick foam on front edge to give comfort to popliteal area.The foam backing done in back ( Executive chairs only) for extra fluffiness and comfort in chair. 2SEAT & BACK HIGH RESILIENCE (HR) POLYURETHANE FOAM :The HR polyurethane foam for seat and back is moulded with density 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 at 25% compression. M.S. VISITOR TUBULAR FRAME (For Thrill Visitore chair): The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. ARMRESTS:The armrest top is moulded from polyurethane(PU) with metal insert and mounted on to a tubular frame. WIDTH (W): 60.5 CM. DEPTH (D): 65.0 CM. HEIGHT (H): 86.5 CM. SEAT HEIGHT (SH): 46.0 CM. This product should be certified by Greenguard

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing and placing desk based modular workstation with size 900x600 System ht - 1200 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 450mm ht.,mounted on Studs. CLIP ON SCREEN: Fabric T-mould (19 mm thick) of 450mm ht. Removable screen and to be used as divider screen. It has a die cast fixing clamp to enable mounting of the screens to the worktop, LEGS: Providing metal powder coated Cube leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, wire risers with cover are considere. . Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 900 mm w x 600 mm d. MODESTY : Metal modesty: Lazer cut perforated Metal modestyMetal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets, Modesty terminates at 400 mm from ground. CPU trolley - with castors, KBPT with mousetray - Metal

SEAT/BACK ASSEMBLY: The seat and back are made from 1.2 ±0.1cm. thk hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam is designed with contoured lumbar support for extra comfort. * 5102R MIDBACK SIZE: 45.0cm(W) x 53.0cm.(H) * 5103R LOWBACK SIZE: 44.0cm(W) x 47.0cm.(H) * SEAT SIZE: 52.0cm(W) x 48.0cm.(D) 2. HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 3. SEAT/BACK COVERS: The seat and back covers are injection moulded in black Co-polymer Polypropylene. 4. ARMREST ASSEMBLY: The one-piece armrests are made of black integral skin polyurethane reinforced with M.S. insert with 50-70 Shore 'A' hardness. The armrests are scratch and weather resistant. The armrests are fitted to the seat with armrest brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT MECHANISM: The permanent contact mechanism is designed with the following features: 360° revolving type. 14° ±2°maximum back-tilt only. Upright position locking. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow is 3 piece telescopic type and injection moulded in black Polypropylene. 8. PEDESTAL ASSEMBLY: The pedestal is fabricated from 0.2 ± 0.02 cm thick HR sheet (IS :DD 1079/HR), powder coated (DFT 40-60 microns) and fitted with an injection molded black Polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 60.0 ±0.5cm. pitch-centre dia. (70.0 ±1.0 cm. with castors). 9. TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.

Supplying and placing in position Main Table & ERU of the following specifications. Its size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. ERU size shall be 1050 Width x 450 Depth x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading. Supplying and placing in position Free Standing Pedestal of the following specifications with Overall Dimensions shall be 390mm(W)x440mm(D)x646mm(H). The construction & Material used shall be welded assembled , 0.8 mm thick CRCA for body shell , drawer front & tray , front side stiffener ,rear aide stiffener and 1.2 mm thick CRCA Top stiffener & Bottom stoffener . The drawer fronts shall be metal front straight edge . Locking shall be 10 lever cam lock & Central RH locking with actuator & lock channel mechanism for box-box-file Pedestal . The top panel shall be metal straight edge top . Castor should be swiveling non - lockable castors mounted below the body shell for free standing full height mobile pedestal and M8 Leveling stud for free standing pedestal . The anti-tipping mechanism shall have fifth roller arrangement mounted below file drawer to avoid toppling of unit when file drawer is pulled out . Partition in drawer shall be 1 no. Partition in box drawers with lock mounted . Plastic pencil tray shall be optional accessory . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Application shall be suitable for pushing below work surface which has got a clear height of 725 mm from below . For drawer pulling side wise tapered recess provided in shell behind drawer fronts . This product should be certified by GREENGUARD.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main Table & ERU of the following specifications. Its size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. ERU size shall be 1050 Width x 450 Depth x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading. Supplying and placing in position Free Standing Pedestal of the following specifications with Overall Dimensions shall be 390mm(W)x440mm(D)x646mm(H). The construction & Material used shall be welded assembled , 0.8 mm thick CRCA for body shell , drawer front & tray , front side stiffener ,rear aide stiffener and 1.2 mm thick CRCA Top stiffener & Bottom stoffener . The drawer fronts shall be metal front straight edge . Locking shall be 10 lever cam lock & Central RH locking with actuator & lock channel mechanism for box-box-file Pedestal . The top panel shall be metal straight edge top . Castor should be swiveling non - lockable castors mounted below the body shell for free standing full height mobile pedestal and M8 Leveling stud for free standing pedestal . The anti-tipping mechanism shall have fifth roller arrangement mounted below file drawer to avoid toppling of unit when file drawer is pulled out . Partition in drawer shall be 1 no. Partition in box drawers with lock mounted . Plastic pencil tray shall be optional accessory . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Application shall be suitable for pushing below work surface which has got a clear height of 725 mm from below . For drawer pulling side wise tapered recess provided in shell behind drawer fronts . This product should be certified by GREENGUARD.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Supplying and placing in position Main table of the following specifications.1200x600x750 Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management Modesty Panel - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under-structure - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Handle is provided for ease of opening. Storage is provided with cam lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up-Down adjustment– 6 steps (7.2 ± 0.5cm range) · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SEAT HEIGHT (SH): 46.0-56.0 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main Table & ERU of the following specifications.1650x1650x750 Primary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel:Made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.understructure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.integrated pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side,Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main Table & ERU of the following specifications.1650x1650x750 Primary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel:Made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.understructure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.integrated pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side,Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

Supplying and placing in position Main Table & ERU of the following specifications.1650x1650x750 Primary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with0.4mm PVC membrane pressed on to top.Softclosing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface:Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel:Made of 25mm thick MDF one side pre- laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.understructure:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.integrated pedestal:Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. This product should be certified by GREENGUARD, Indoor Advantage GOLD & GREEN PRO.

. NOTE: HINGE DOOR UNITS (HDU) SPECIFICATIONS FEATURES Width: 450 / 600 / 650 / 750 / 800 / 900 / 950 / 1000/ 1050/ 1200 Height (For Leg Unit) : 750 / 1200 / 1353. UNIT-SIZE Height (For Skirting Unit) : 750 / 119 / 1343. Refer sheet 3 & 4 for all the available options. Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding CONSTRUCTION & MATERIAL of 0.8mm thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyster powder of 50+10 microns thickness. In case of 2.5feet Height Storage units,-wooden top is provided which is made of 25mm thick Pre-laminated TOP OPTIONS board whereas 4.0feet and 4.5feet height Storage unitsare provided with 11mm thk bent metal tops made of 0.8mm thk C.R.C.A (as per IS:513). The metal tops are coated with Epoxy polyester powder of 50+10 microns thickness. DOOR & DOOR OPENING Single door opening for 450 & 600w units whereas two door opening for all other width options (i.e; 650 /750/ 800/ 900/ 950/ 1000/ 1050/ 1200W).The doors are made of 18mm thk Pre-laminated boards with decorative laminate on one side and backing laminate on the other side,Uniformly distributed load capacity for each shelf is 40Kg maximum. The skirting units are provided with 150mm high skirting made of 0.8mm thick C.R.C.A (as per IS: 513) and is coated with Epoxy Polyester powder of 50+10 microns thickness. Screw. type adjustible leveler with plastic base provides vertical adjustment for floor unevenness and leveling of units. Back panels are made of 18mm thick Pre-Laminated boards with options of Decorative laminate as well as Fabric finishes. 2,5' height units consist of single back panel whereas 4.0' height and 4,5' height units consist of split back top panel and split back bottom panel separated by an Aluminium extrusion. 3-way nickel plated wooden furniture lock is provided for effective. and positive locking of doors.

Providing, supplying and placing of storage unit. Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

SEAT/BACK ASSEMBLY: The seat and back should be made from seasoned wood and plywood. The same should be upholstered with black synthetic leather and polyurethane foam. BACK SIZE: 46.0cm. (W) X 27.0cm. (H) SEAT SIZE: 46.0cm. (W) X 40.0cm. (D) ARMREST TUBE: The armrest tube should be made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type frame made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and powder coated (DFT 40-60 microns). Overall Dimensions of Chair Seat Height - 48.0 cm. Height - 87.5cm. Width & Depth of Chair as measured from base - Width-58.0 cm and Depth-56.5 cm.

1800 Head 1800 X 850 X 740, 2 STR MAIN - 1350 X 600 X 740. 2 STR END_LH - 1350 X 600 X 740, 2 STR END_RH - 1350 X 600 X 740 Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns). Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture. BACK SIZE: 48cm.(W) X 76.0cm.(H) SEAT SIZE: 51.0cm.(W) X 48.0cm.(D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The armrest top should be made of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height should be adjustable up to 6.5±0.5cm. in 5 steps . KNEE TILT SYNCHRO mechanism WITH SEAT DEPTH ADJUSTMENT mechanism: The mechanism should be designed with the following features: • 360° revolving type single point control. • Front pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat back tilting ratio of 1:2 • Seat depth adjustment of 6.0 ±0.5cm. can be locked in 6 positions ADJUSTABLE BACKREST: The backrest consshould be ts of a sliding up down mechanism, which can be adjusted in the range of 7.5±0.5cm. and can be locked in 5 positions for correct position of lumber support. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment of 10.0±0.3cm. PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet . chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 66.0±0.5cm. Pitch-center dia. (76.0±1.0 cm with castors). TWIN WHEEL CASTORS The twin wheel castors should be injection moulded in black Nylon. Overall Dimensions of Chair Seat Height - min 47.5 to max 57.5cm. Height - min 103.5 to max 120.5cm. Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm.

Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood and upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture. BACK SIZE: 48cm.(W) X64.5cm.(H) SEAT SIZE: 51.0cm.(W) X 48.0cm.(D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The armrest top should be made of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height should be adjustable up to 6.5±0.5cm. in 5 steps . KNEE TILT SYNCHRO mechanism WITH SEAT DEPTH ADJUSTMENT mechanism: The mechanism should be designed with the following features: • 360° revolving type single point control. • Front pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat back tilting ratio of 1:2 • Seat depth adjustment of 6.0 ±0.5cm. can be locked in 6 positions ADJUSTABLE BACKREST: The backrest consshould be ts of a sliding up down mechanism, which can be adjusted in the range of 7.5±0.5cm. and can be locked in 5 positions for correct position of lumber support. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment of 10.0 ±0.3cm. PEDESTAL ASSEMBLY: The pedestal should be fabricated from 0.2 ± 0.02 cm thick HR sheet ( should be : DD 1079 / HR skin pass ), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal should be 66.0±0.5cm. Pitch-center dia. (76.0±1.0 cm with castors). TWIN WHEEL CASTORS The twin wheel castors should be injection moulded in black Nylon. Overall Dimensions of Chair Seat Height - min 47.5 to max 57.5cm. Height - min 93.4 to max 110.4cm. Width & Depth of Chair as measured from pedestal - Width-76.0 cm and Depth-76.0 cm.

Providing, supplying and placing of Visitor Chair. SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded Polyurethane Foam. The back should be made up 1.2 ±0.1cm. thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The back ply and foam should be designed with contoured lumber support for comfortable seating posture. MID BACK SIZE: 48.0cm.(W) X 64.5cm.(H) SEAT SIZE: 51.0cm.(W) X 48.0cm.(D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam for seat and back should be moulded with density = 45±2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression. ARMRESTS:The armrest top should be made of moulded polyurethane (P.U) and mounted on to a fixed type tubular armrest support which should be chrome plated Finish. FIXED BACKREST: The backrest consshould be ts of a fixed type mechanism i.e. no back up/down adjustment. FIXED SPINE : The seat and backare arrested together withfixed type spine i.e no backup/down adjustment ;made of 0.8 ± 0.05cm thk HR steel ans id back power-coated (DFT 40-60 micros). TUBULAR VISITOR FRAME :The tubular frame is cantilever structure & made of Dia 2.54 ± 0.03cm. X 0.2±0.016cm.thk . M.S. E.R.W. tube with a M.S. Spine mounting bracket welded to it. Back spine is fitted to the assembly. The frame finish is Nickel Chrome plated (15-20 microns). Overall Dimensions of Chair Seat Height - 47.7cm. Height - 93.0cm. Width & Depth of Chair as measured from pedestal - Width-66.5 cm and Depth-61.6 cm.

Supplying and placing in position conference table of the following specifications. 2 STR MAIN - 1350 X 600 X 740. Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes. Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns). Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. This product should be certified by GREENGUARD, Indoor Advantage GOLD, GRIHA & SVAGRIHA & GREEN PRO.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest is is made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM. This product should be certified by Indoor Advantage GOLD, GREENGUARD GOLD, BIFMA Level 2 & GREEN PRO.

Providing, supplying and placing of classroom chair with desklet. SEAT / BACK: The seat sub-assembly should be made up of 1.2±0.1cm thk Plywood upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The seat can tip-up when not in use and thshould be feature can be used while stacking the chairs horizontally The back sub-assembly should be made up of injection-moulded polypropylene inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The contoured back with width extension at the bottom should be a should be designed to give comfort to lower back. The back flexing features allows the back to tilt by 9c±2' to aid the user in adopting a comfortable reclining posture. Both these sub-assemblies should be fixed to the tubular structure, BACK SIZE: 45.2cm (W) X 44.6cm (H) SEAT SIZE: 47.0cm (W) X 50.0cm (D) TUBULAR FRAME STRUCTURE: The powder-coated 4 leg structure should be made of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R.W. Tube front and rear leg welded along with connecting tube made of 1.9 ±-0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube to form the tubular frame assembly. The legs should be provided with injection-moulded adopter bush in black Nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use_ The chairs can be stacked horizontally when not in use_ POLYURETHANE FOAM: The Polyurethane foam should be moulded with density = 70.0 ±8.0 kg/m3 and Hardness = 12 ±2 for Seat & 16 ±2 for back at 25% compression. ARMRESTS: The armrest structure should be made up of 2.2 ±0.03crn dia x 0.25 ±0.02cm thk M.S. E R.W. Tube welded to the Tubular Frame structure and having a scratch-resistant tant ABS Arm top. FULL DESKLET: The Full Desklet assembly should be Flip-up type and should be made up of extension tube of 1.9 ±0.02em dia x 0_2 ±0.016cm thk PAS. E.R.W. Tube and a support tube on L.H. side of 1.6 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube on which an scratch resistant tant ABS desklet top should be fixed and covered on bottom side with a bottom cover. BRAKE-LOADED CASTORS : The brake-loaded castors should be assembled to the chair legs, to give a free movement for maneuvering the chair when not in use and it will brake the movement when load should be applied (while in use) to give a stable feel. The twin wheel castors should be injection molded in black Polypropylene. Overall Dimensions of Chair Seat Height - 47.5 cm. Height - 89.0cm. Width & Depth of Chair as measured from base - Width-66.5cm and Depth-84.0 cm. This product should be certified by Indoor Advantage GOLD & GREEN PRO.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ?85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking TGrid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The

Providing and fixing anodised aluminium work for doors, windows, ventilator? and partitions with extruded built up standard tubular and otner sections of approved make conforming to IS : 733 and IS : 1285,anodised trasparent or dyed to required shade according to IS : 1868,(Minimum anodic coating of grade AC 15), fixed with.rawl plugs and screws or with fixing clips , or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust fre straight, mitred and jointed mechanically wherever required including cleat angle,.Aluminium snap beading tor glazing/paneling, C.P. brass/stainless steel screws, all complete as per architecttural drawings and the directions of Engineer-in-charge.(Glazing and panelling to be paid for separately.)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber /neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS:1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Excavating trenches of required width for pipes cables, etc, including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil , and then returning the soil as required , in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc and disposing of surplus excavated soil as directed , within a lead of 50 m

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubbergasket, GI bolts, nuts, washers etc.as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Internal Hydrant System

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless steel (Grade 304)

Providing and fixing fully glazed MS fully welded construction double leaf door shutter for fire hydrant station fabricated from MS 50x50x6 mm angle iron frame, fixed to wall and hinged MS 40x40x5 mm angle iron door shutter with required MS sash bars for glazing complete with locking arrangements, stove enamelled fire red finish with 'FIRE HYDRANT' written in front. Approximate size 2100x900mm.

Providing and placing in proper position Stainless Steel 63mm dia short size branch pipes with 20 mm dia nozzles with 63mm instantaneous coupling ISI marked (IS:903).

Providing and fixing brass/bronze lever operated ball valve of full flow with stainless steel ball (AISI 304 and spindle AISI 410) with setting and gland of superior quality having minimum working pressure of 20 kg/cm2. 25mm dia

Supply, installation, testing & commissioning of 25mm dia air release valves of approved make on the top of each 150mm dia basement sprinkler ring main as per standard fire practice

Providing and fixing pressure gauges with isolation cocks and chrome plated copper pipes as hydrant station to read pressure from 0-25 kg/cm2 complete and of dial dia 150 mm.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

External Hydrant System

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless steel (Grade 304)

Providing and fixing fully glazed MS fully welded construction double leaf door shutter for fire hydrant station fabricated from MS 50x50x6 mm angle iron frame, fixed to wall and hinged MS 40x40x5 mm angle iron door shutter with required MS sash bars for glazing complete with locking arrangements, stove enamelled fire red finish with 'FIRE HYDRANT' written in front. Approximate size 2100x900mm.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipecoupling as required :

(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation,conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads.

a) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) b) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. c) SuitableHP squirell cage induction motor TEFC type suitablefor operation on 415 volts, 3 phase 50 Hz AC supply with IP55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. d) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. e) Suitable cement concrete foundation duly plastered and with anti vibration pads.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 (b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required

Providing, fixing, testing and commissiong of motor control centres fabricated from 16 gauges MS sheet with powder coated finish. The control panels should be comparable with H.P. of the motor as specified.

Providing and fixing motor control centres fabricated from 16 gauge M.S. sheet with Powder Coated finish. The control panels should be compatible with H.P. of the motor as under and as per spcifications with automatic star delta starters. (One separate panel to be located in the plant room).

One incoming main isolation MCCB TP of Min. 250 Amps. rating.

Fully taped aluminium bus bar of required capacity in a separate bus bar chamber.

Isolation MCCB for each unit of required rating and with fully automatic starter as per requirement with push button and ON/OFF indicating lights for each unit, for following requirements:

One main fire pump of 50 HP.

One jockey pump of 10 HP (Each).

One Diesel Pump Controlling System

Single phasing preventors of suitable rating one for each motor.

One 96mm square panel type Amp. meter reading 0-500 Amp. for main fire pump and sprinkler pump.

One 96mm square panel type Amp. meter reading 0-500 Amp. for each Jockey pumps.

Appropriate etched plastic plate for each starter/switch.

Colour coded internal wiring from incoming main to bus bar, switch gear, starters, meters indicating lamp etc., complete in all respects.

Providing and fixing heavy duty Aluminum armored cables 1.1 KV grade including necessary support clamps at ceiling level, connection lugs and double compression glands, complete in all respects.

Power cable 3 core 16 Sq.mm

Power cable 3 core 25 Sq.mm

Fire Alarm System

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Two pair, 2-core, 1.5 sqmm

Automatic Sprinkler System

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Fire Extinguishers

Supply, Installation, Testing & Commissioning of ISI marked (IS:15683) Portable fire extinguisher, of 4.5 kg capacity Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia 1m long & complete in all respects including initial fill with CO2 gas confirming to IS: 307-1966 filled to a filling ratio of not more than 0.667of not more than 0.667and wall suspension bracket.

Supply, Installation, Testing & Commissioning of ISI marked (IS:2878) Portable fire extinguisher, of 22.5 kg capacity Carbon-dioxide type flat base including valve, discharge hose of not less than 10 mm dia 1m long & complete in all respects including initial fill with CO2 gas confirming to IS: 307-1966 filled to a filling ratio of not more than 0.667of not more than 0.667and wall suspension bracket.

Amount Of Boq (Civila+furniture+Fire Fighting) Rs=

Amount Of N/S Items Rs.=

Amount Of SOR Items Rs.=

Applying Correction factor @ 0.982 on Schedule Items for SOR Items ( C) Rs=

Add 5.36% G.S.T on (D) =

Wiring for light point/ fan point/ exhaust fan point/ Call bell Point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable size G.I box etc. as required. Group - 'C'

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular switch box including connection but excluding modular plate etc. as required.

Supplying and fixing suitable size G.I box with modular plate and cover in front on surface or in recess including providing and fixing 5 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc, as required.

Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch connection, painting etc, as required.

Supplying and fixing 2 pin, 5 amp. ceiling rose on the existing junction box/PVC box including connection etc as required.

Supplying and fixing batten/angle holder including connection etc. as required.

Supplying and fixing Ding-Dong call bell suitable for single phase, 230 volts complete as required.

Supplying and fixing following modules G.I. box along with modular base and cover plate for modular switches in recess etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 amps modular socket outlet and 25 amp modular SP MCB 'C' curve, including connections, painting etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 nos. 5 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required.

Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus-bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB / RCCB / Isolator)

Supplying and fixing following rating, 240 volts, ‘C’ series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.

Supplying and fixing following ways, surface/recess mounting, Vertical three phase distribution board ( VTPN DB's ) of CRCA sheet steel, dust protected, duly powder painted suitable for upto 250 amp, four pole MCCB as Incomer and SP/TP MCB's as outgoing inclusive of tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's etc as required. (but without MCCB & MCBs),Legrand/Scneider.

Supplying and fixing 4'X18 watt LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required.

Supplying and fixing recess/surface mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 210 cum/min including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.

Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

Supply and fixing of following sweep/ sizes PVC/ABS square body Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc as required.

Supply and installation of 600 mm, 230 V A.C. wall mounted Air circulator, heavy duty fan including fixing the bracket, making connection, testing, commissioning etc as required.

Supplying and fixing of 32 mm dia X 1.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV/ HPSV/ LED street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.

Supply of following sizes and core XLPE/PVC insulated PVC sheathed (Heavy duty) armoured electric cable with aluminium conductor for working voltage upto 1.1 KV as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cble of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc as required.

FIRE SUPPPRESSION SYSTEM

Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run)

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required.

Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/ termination with GI nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm)

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 6A 'C' series SP MCB, connector, and suitable size foundation bolts with template as required.(but without pole foundation)

Providing and making of following sizes octagonal street light pole foundation in reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) of specified size including PVC conduit, form work, curing, reinforcement, excavation and refilling etc. as required.

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supply of following sizes and core XLPE/PVC insulated PVC sheathed (Heavy duty) armoured electric cable with aluminium conductor for working voltage upto 1.1 KV as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cble of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.

Supplying and connection of following sizes ISI marked FR PVC insulated, single core copper conductor cable etc as reqd.

Fabrication, supply, Installation testing and commissioning of Street Light Feeder Pillar of cubical construction, floor mounted type, fabricated out of 14 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, digital ammeter & voltmeter, RYB LED lamp, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals etc. complete in all respect, suitable for following incoming and Outgoings as required. (CPRI Approved Panel Mfg.)

Supply ,Installation, testing and commissioning of 2 Pole mounted DP providing I no 11kv,400A GOC in accordence with ie rules& local authority specifications and drawing and comprasing the following

Supply, Installation, testing and commissioning of silent type DG set comprising with diesel engine water cooled , synchonous alternator , AMF panel three phase , acoustic enclosure, battery with charger and related accessories, including PCC 1:2:4 platform, incoming cable 10 meter, earthing GI/CU plate 2 nos. including exhaust pipe B class with insulation as per CPCB IV+ norms etc as required. Make:- Kirloskar/ Ashok Leyland/Cummins.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power H.T. cable with aluminium conductor for working voltage upto 11 KV as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Supply of following sizes and core XLPE/PVC insulated PVC sheathed (Heavy duty) armoured electric cable with aluminium conductor for working voltage upto 1.1 KV as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cble of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required.

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required. In the existing trench, complete as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required. (For Transformer Neutral and Feeder panel)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Suuply, Installation, testing and commissioning of a fully enclosed type 100 KVAR capacitor panel, dust vermin and IP 55 protected, fabricated out of 14 guage MS sheet duly DPC coated including interconnections, relays specified as below complete as required.

SITC of 2MP IR Bullet Fixed lens Camera -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S), support H.265, H.264, MJPEG, DWDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified. (Approved Makes: Hikvision/ Honeywell/ Bosch)

SITC of 2MP IR Indoor Dome Fixed lens Camera- 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, Color: 0.01 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, DWDR, 3D Digital Noise Reduction, Tripple individually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, IK10, Edge Anlalytics- Line crossing detection, intrusion detection, Motion detection, video tampering, UL, CE, FCC certified. (Approved Makes: Hikvision/ Honeywell/ Bosch)

SITC of 2MP IR Outdoor PTZ Camera - 1/2.8" Progressive Scan CMOS, 1920 × 1080 at 60fps, 4.8 mm to 153 mm, 32× Optical, 16x digital zoom, Color: 0.005 Lux at F1.6, B/W: 0.001 Lux at F1.6, ICR, ONVIF, support H.265,MJPEG, 120 dB WDR, 3D Digital Noise Reduction, HLC, BLC, Defog, EIS, Tripple individually configurable stream, 24 VAC & Hi PoE, IR range: 150m, Pan: 360° endless, Tilt: From -15° to 90° (auto-flip), Pan Speed - from 0.1°/s to 160°/s, Preset Speed: 240°/s, Tilt Speed- from 0.1°/s to 120°/s, Preset Speed: 200°/s, Presets- 300, Alarm Input-2-ch alarm input, Alarm Output-1-ch alarm output, Audio-1 channel input & output, Support on-board storage up to 256 GB (SD card not included), IP66, IK10, Face Detection, Intrusion Detection, Line Crossing Detection, Region Entrance Detection, Region Exiting Detection, UL, CE, FCC certified. (Hi-PoE injector under Si Scope, if PoE is used)(Vertical Pole Mounting Bracket)) (Approved Makes: Hikvision/ Honeywell/ Bosch) /Equivalent

SITC of 32ch Network Video Recorder - Connect Up to 64 IP Cameras, Dual OS, Up to 12 Megapixels Resolution, Two independent HDMI outputs, one HDMI output of 4K resolution,1 VGA output with output upto 1920 × 1080, Support H.265, MJPEG, Supports N+1 hot spare system,Supports RAID0, RAID1, RAID5, RAID6 and RAID10 ,Supports HDD hot swap, Supports Dual Power-Redundant, Incoming Bandwidth 320 Mbps, 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD upto 6TB, 3 × USB at least 1 × USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified. (Makes: Hikvision/ Honeywell/ Bosch)

SITC of 6TB Surveillance Hard Disk Custom-built for surveillance applications with Image Perfect firmware for crisp, clear, 24×7 video workloads Maximum 180TB/year workload rating—3× the workload rating of desktop drives—for reliable performance in write-intensive surveillance systems Rotational vibration (RV) sensors help maintain performance in RAID and multi-drive systems (4TB or higher) Up to 10TB of capacity to store up to 10,000 hours of HD video (Approved Makes: Seagate/WD/Toshiba)

SITC of SWITCH PORTS: 16-Port 10/100/1000 + 2 x 1GE copper/SFP combo. Fixed-configuration 1RU x 1/2, half-rack width chassis, 16 x RJ45 10/100/1000 BaseT PoE+ ports 2 x SFP/RJ45 combo ports 2 x SFP ports, 1 x USB port (type A, USB 2.0), 1 x Console port (RS232 RJ45)IEEE 1588v2 capable ports 12, MACsec capable ports 12 Switch capacity 24 Gb/s, PoE power budget 115W, Includes power cord & manuals/software access cards, Includes RJ45 to DB9 adaptor Operating temperature: -10°C to 60°C (14°F to 140°F) Storage temperature -40°C

SITC OF Video Management Software equips users with live video from the camera feed, access control, video intercom, alarms, and data storage. Support upto 120 Camera Streaming. Abundant Modules – Video, access control, attendance, intercom, alarm, E-map, and more. Friendly User Experience and Visual Design – Lightweight, flat UI, and component-based design. Multiple-Languages – 33 languages, including English, Simplified Chinese, Arabic, etc.

SITC OF Server for Video Management Software Form Factor: 1U rack, Processor: 1x Intel® Xeon® processor E-2300 or 1x Intel® Pentium® processor GPU Support: NVIDIA Quadro T1000 PCIe Active GPU, Memory: Up to 128GB in 4x DIMM slots, Drive Bays: Up to 10x 2.5 inch hot-swap SATA/SAS drives or 4x 3.5-inch hot-swap SATA/SAS drives Expansion Slots: Up to 2x PCIe Gen4 x8 slots

SITC OF 43” Professional display rated for 16/7 operation with essential professional functions Screen Size 43, Brightness (cd/m²) 350, Contrast Ratio 1200:1, Dynamic Contrast, Ratio 400,000:1, Response Time (ms) 8.0, Display Resolution, (H x V, pixels) 3840 x 2160, HDR (High Dynamic Range) compatibility yes (HDR10, HLG)

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/ recessed PVC conduit as required.

Supply , Installation , Testing and Commissioning of 12U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts. Makes: Poweride/MTS/Rittal/APC/APW

SITC of 6 U network Rack

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/ recessed PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply , Installation , Testing and Commissioning of CAT6 information outlet (I/O) for Data, Voice, Camera & Wi-Fi at user end. Makes: Belden/Siemon/Panduit/Leviton

Supply , Installation , Testing and Commissioning of loaded 24 port CAT6 jack panel for CAT6 cable termination at rack end.Makes: Belden/Siemon/Panduit/Leviton

Supply , Installation , Testing and Commissioning of CAT6 patch cord 3 feet for rack side switch to jack panel connectivity. Makes: Belden/Siemon/Panduit/Leviton

Supply , Installation , Testing and Commissioning of CAT6 patch cord 7 feet for information outlet (I/O) to end user device connectivity.Makes: Belden/Siemon/Panduit/Leviton

Supply , Installation , Testing and Commissioning of 1, 2 and 4 port face plate white for I/O fixing at user side. Makes: Belden/Siemon/Panduit/Leviton

Supply , Installation , Testing and Commissioning of 22 U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.Makes: Netrack/MTS/Rittal/APC/APW

Supply , Installation , Testing and Commissioning of 9 U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.Makes: Poweride/MTS/Rittal/APC/APW

Supply , Installation , Testing and Commissioning of Core Switch Port Density - 14 X 1/10G SFP Ports and 12 X 1/10G Base T 2 x 40/100 G QSFP28 Ports. Power Supply - Redundant Hot Swappable Power Supply - AC/DC, Virtual Chassis/ Stacking Option - Upto 6 Switches or more, RAM - 8 GB or better, Flash and Buffer - 32GB or better and 32MB Packet Buffer Switching Capacity and forwarding Rate, 900 Gbps or better and 650 Mpps or better , Latency & MTBF Latency: <650 ns MTBF: 384,636 h,MAC Address 64K, Routes IPv4 - 12k or better, IPv6 - 12k or better. Support for Egress rate limiting, Eight egress queues per port, IEEE 802.1Q, 802.3x, DiffServ, Jumbo frame. Protocol Support - IGMP Snooping V1, V2, V3, MLD, PIM-SM/PIM-SSM/PIM-DM/PIM-Bidirectional, DVMRP,RIPv1v2,RIPing ,OSPFv3, RIP, BGPv4, MP-BGP,GRE, IS-IS, ITU-T G.8032, IEEE 802.1s, IEEE 802.3ad/802.1AX Link Aggregation Control Protocol (LACP), Ipv4/Ipv6, DHCP Option 82, BPDU, STP Root Guard, SIP detection, SPB-M or MPLS, IEEE 802.1ae, MIB, NTP,Built-in CPU protection against malicious attacks,The Switch Should have 1+N redundant supervisor manager in Virtual chassis with In-Service Software Upgrade (ISSU), VXLAN, ARP Poisioning detection, Policy based routing (PBR),SDN support through Restful API and openflow 1.3.1, Management SNMP V1,V2,V3, Web GUI, CLI, USB or equivalent memory card, IPv6 management feature on open standards, IEEE802.1ag, TDM or equivalent standards

Security Should support Access Control Lists (ACLs), DHCP snooping, IEEE802.1x based port authentication, RADIUS/ TACACS+, SSL, SSH, port mirroring,NTP, IEEE 1588, AES, Syslog, MD5, LLDP-MED, BPDU Blocking, BFD, Unified management, control and fabric-mesh virtual chassis technology, Autosensing IEEE 802.1X multi- client, multi-VLAN support for bridging and SPBM/VXLAN services,MAC-based authentication for non-IEEE 802.1X hosts, MAC address lockdown, Prevention from ARP attacks Resiliency IEEE802.1q, IEEE802.1d, IEEE802.1s, IEEE802.1w, ITU-T G.8032 ring resilience/ring protection, VRRPv2, Operating Temperature and Humditiy Temperature: 0 to 45Deg Humidity: 5% to 95% (non-condensing) Safety Certifications CE, EN 55022, RoHS, US UL 60950, CSA22.2 , FIPS 140-2, EAL2 & NCPP Certified , EN 60825-1/2 Laser SFP , SFP should be of same make as switch. Vendor to be present in Gartner Magic Quadrant. The Switch shall work with on-premise and cloud based NMS without change in hardware/software/OS Image. The Switch should be EAL2/NDPP certified Cisco/Juniper / Alcatel-Lucent

Supply , Installation , Testing and Commissioning of Access switch Port Density 24 X 1G RJ-45 Ports 2 x 1G/10G SFP+ Ports and 2 x 1G SFP/Base-T Combo Ports Power Supply Internal Power Supply Virtual Chassis/ Stacking Option Upto 4 Switches or more RAM 1 GB or better Flash 1 GB or better Switching Capacity and forwarding Rate 92 Gbps or better and 68 Mpps or better Latency & MTBF Latency: < 4 µs MTBF: 2595 k hours Layer 2 Features Mac Address:16K or more VLAN: 4K or more System Policies: 1.5K or more Max Jumbo Frame: 9216 bytes Multicast Group: up to 1000 Quality of Service Auto QoS for switch management traffic,Policy-based QoS, Traffic Prioritization, Priority Queues: Eight hardware-based queues per port, SPQ, WRR

Protocol Support Static Routing, MSTP, RSTP, PVST+,IPv6 Tunneling, LACP, LAG, IGMPv3, DHCP, DHCP82,DHCP Relay for IPv4/IPv6,Multiple microcode image support with fallback recovery, ARP,SDN support through Restful API and openflow 1.3.1 Management Loopback IP address support for management per service, Policy- and port-based mirroring, Remote port mirroring, sFlow v5 and Remote Monitoring (RMON), Unidirectional Link Detection (UDLD),Digital Diagnostic Monitoring (DDM), LLDP-MED, NTP,MVRP, SNMP, sflow or equivalent Security Dynamic change of authentication (CoA),MAC-based authentication for non-IEEE 802.1X hosts, MAC address lockdown, Prevention from ARP attacks, Web based Authentication, Autosensing IEEE 802.1X multi-client, multi-VLAN support,RFC 1321 MD5, RFC 2284 PPP EAP,RFC 1826/1827/4303/4305 Encapsulating Payload (ESP) and crypto algorithms, RFC 2104 HMAC Message Authentication, Built-in CPU protection against malicious attacks Resiliency Unified management, control and virtual chassis technology, Virtual Chassis 1+N redundant supervisor manager, Virtual Chassis In-Service Software Upgrade (ISSU),Smart continuous switching technology, IEEE 802.3ad/802.1AX Link Aggregation Cisco/Juniper / Alcatel-Lucent

SITC of 24 Port POE Network Switch Port Density - 24 X 1G RJ-45 PoE+ Ports with 380W power budget, 2 x 1G/10G SFP+ Ports and 2 x 1G SFP/Base-T Combo Ports upgradable to 2 x 10G SFP+ Ports Power Supply - Internal Power Supply, Virtual Chassis/ Stacking Option- Upto 4 Switches or more RAM - 1 GB or better, Flash - 1 GB or better Switching Capacity and forwarding Rate - 128 Gbps or better and 190 Mpps or better Latency & MTBF - Latency: < 4 µs MTBF: 1447 k hours Layer 2 Features - Mac Address:16K or more VLAN: 4K or more, System Policies: 1.5K or more Max Jumbo Frame: 9216 bytes, Multicast Group: up to 1000 Quality of Service - Auto QoS for switch management traffic,Policy-based QoS, Traffic Prioritization, Priority Queues: Eight hardware-based- queues per port, SPQ, WRR Protocol Support - Static Routing, MSTP, RSTP, PVST+,IPv6 Tunneling, LACP, LAG, IGMPv3, DHCP, DHCP82,DHCP Relay for IPv4/IPv6,Multiple microcode image support with fallback recovery, ARP,SDN support through Restful API and openflow 1.3.1, Management - Loopback IP address support for management per service, Policy- and port-based mirroring, Remote port mirroring, sFlow v5 and Remote Monitoring (RMON), Unidirectional Link Detection (UDLD),Digital Diagnostic Monitoring (DDM), LLDP-MED, NTP,MVRP, SNMP, sflow or equivalent

Security - Dynamic change of authentication (CoA),MAC-based authentication for non-IEEE 802.1X hosts, MAC address lockdown, Prevention from ARP attacks, Web based Authentication, Autosensing IEEE 802.1X multi-client, multi-VLAN support,RFC 1321 MD5, RFC 2284 PPP EAP,RFC 1826/1827/4303/4305 Encapsulating Payload (ESP) and crypto algorithms, RFC 2104 HMAC Message Authentication, Built-in CPU protection against malicious attacks Resiliency - Unified management, control and virtual chassis technology, Virtual Chassis 1+N redundant supervisor manager, Virtual Chassis In-Service Software Upgrade (ISSU),Smart continuous switching technology, IEEE 802.3ad/802.1AX Link Aggregation Control Protocol (LACP) and static LAG groups across modules Operating Temperature and Humditiy - Temperature: 0 to 45Deg Humidity: 5% to 95% (non-condensing) Safety Certifications - CE, EN 55022, RoHS, WEEE US UL 60950, CSA22.2, FIPS 140-2, EN 60825-1/2 Laser, IEC 62368-1 SFP - SFP should be of same make as switch. Vendor to be present in Gartner Magic Quadrant. The Switch shall work with on-premise and cloud based NMS without change in hardware/software/OS Image. Cisco/Juniper / Alcatel-Lucent

SITC of WIFI Access Point Proposed solution will be Controller less/HW Controller based/SW Controller based but all the Access Points managed centralized . The WLAN solution shall propose an indoor 802.11ax Wifi 6 MU-MIMO indoor dual radio AP Access Point (2.4, 5G) AP to support 2x2:2 on 5 Ghz and 2X2:2 on 2.4 Ghz. Access Point shall offer up to 1200 Mbps throughput on the 5Ghz band (low and high bands) and up to 573 Mbps throughput on the 2.4GHz band. 2 x 10/100/1000Base-T autosensing (RJ-45) port . Both ports should support 802.3at PoE,1x USB 2.0 Type C AP should support ACL, wIPS/wIDS and DPI application, 802.11i, 802.1x Access Point shall propose a Factory reset button. Access Point shall support up to 16 SSIDs (8 per radio) with 512 Clients and should support BLE 5.1/Zigbee Integrated. Single AP can act in dual mode (WLC/Client Serving) with controller to support 256 Access Points in single cluster. Distributed Radio Management, Radio Dynamic Adjustment (RDA), Transmit Power Control @ 18 dBM(TPC), DFS, VHT20,40,80 It should support Advanced Cellular Coexistence (ACC) i.e Minimizes interference from 3G/4G cellular networks, distributed antenna systems, and commercial small cell/femtocell equipment L2 Roaming 802.11r Roaming, 802.11K, 802.11v

Operating temperature must be 0°C to 45°C Humidity must be 10% to 90% non-condensing. WFA, UL2043 Plenum rating, EMI,RoHS, REACH, WEEE

Supplying and drawing 2 pair, 0.5 sqmm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed PVC conduit as required.

Supplying and drawing 4 pair, 0.5 sqmm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed PVC conduit as required.

Supply, installation, testing & commissioning of termination box for 50 pair EPABX system complete as required

SITC of Communication appliance for Voice,configured for:- 01 PRI- 08 Trunk- 40 Digital- 150 Analog Extensions Internal CLI on Digital Phones and Analog CLI Phones Alcatel-Lucent/Matrix/Cisco

SITC of Ananlog Phone Display type 1 line-Dot-matrix + 1 line 7-segments+ 1 line icons alphanumeric displayDate and time displayed in standby mode Call duration display Number of ringtones 1Ringtones volume levels 3 (high / low / off Handsfree function Handsfree volume control 3, Direct access memories 82-touch memories 10,Caller Identification type I & IIIncoming call log, Mute key Wall-mountable, Dialing type Tone / Pulse Protocol FSK & DTMF, Removable line connector cord RJ11/RJ11, Power supply No battery required Alcatel-Lucent/Matrix/Cisco

SITC of Console Phone Optimised access to all ALE communications features Touch screen or large display with LED buttons 3D Symphonic HD super wideband sound Cylindrical sound bar with 3D diffusion and up to 3 microphones Elegant metal and textile casing with 4 interchangeable colours Extensive connectivity: USB, WLAN, Bluetooth, IP, hybrid digital/IP Secure remote working: VPN, SRTP Accessories include: Alphabetic keypad, wireless handset, WLAN and Bluetooth module, colour display key module Centralised management and deployment from the cloud

Supplying, installing, testing and commissioning of the following as per specification complete with junction box, as and where required.without JB Analogue addressable Photo Electric type Smoke Detector with mounting base, address switch complete as required. Make - Agni/Bosch/Siemens

Analogue addressable rate of rise cum fixed temperature thermistor type heat detector with mounting base, address switch complete as required. Make - Agni/Bosch/Siemens

Addressable type Manual Call Point complete as required. Make - Agni/Bosch/Siemens

Addressable Hooter cum strobe complete as required. Make - Agni/Bosch/Siemens

Addressable strobe complete as required. Make - Agni/Bosch/Siemens

Duct casting unit with casing of fabricated aluminium/poly carbonate and hinged inspection cover, 1 No. inlet of proper length & 1 no. outlet tube & with 1 no. analogue addressable photoelectric type Smoke detector with mounting base, address switch complete as required. Make - Agni/Bosch/Siemens

Analogue addressable Fault Isolators for isolating shorted, de-wired and loose circuits between two successive Fault isolators with automatic resetting arrangement. (max. 20 devices for one fault isolators). Make - Agni/Bosch/Siemens

Analogue addressable, automatic commandable Control Switches for switching on/off various ventilation fans, pressurisation fans, zones of speakers etc. and other Fire operation related devices and complete as required. Make - Agni/Bosch/Siemens

Addressable Input Card/monitor module for connecting to Flow Switch etc. Make - Agni/Bosch/Siemens

Response indicator consisting of 16 gauge MS box with 75 x 75 x 6 thick cross brushed MS face plate. Make - Agni/Bosch/Siemens

Zone address module to connect conventional zones with the addressable panel. Make - Agni/Bosch/Siemens

Each loop of fire alarm panel shall have 10 to 15% spare addressable units. At all panels global access to be provided. Information of all the panel shall be accessible from any of panels through networking. All panels shall be upgradable to minimum 25% more loops. Other requirements are given in the specifications. The no. of loops may be changed based on the loop capacity of the panel. loop card.

Providing, installing, testing and commissioning of Zero Loop Repeater Panel for Fire Alarm System with piezo sounder, LCD alpha numeric character display with accept/reset buttons for alarm address of any sensor/field device. The Repeater Panel shall provide field device address as required. The Repeater Panel shall be active & all the setting for fire alarm system can be configured with panel.

Wall mounted speaker with three tap changers in acoustically treated box with speaker and line matching transformer (2W max).(For car park & double height areas)

Ceiling mounted baffle speaker with three tap changers (2W).

Portable UL listed fire phone handsets in a suitable enclosure.

Addressable fire phone jack plates with control/monitor module.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specification as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- (a) Solar Photovoltaic Module conversion efficiency shall not be less than 16.5% PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. (b) Connections and interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kv grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories complete job etc. as required. (Including 5.36% GST) Make-Tata Power/Adani/Vikram solar/Waaree

SITC of 30 KVA, 3 Ph, IGBT Based Inverter & Rectifier Both Side True Online Double Conversion UPS and M.S Powder Coated Rack & Interconnecting cable with inbuilt Phase Sequence Correction. For 30 Minutes Battery Backup using 12 Volt 65 Ah, SMF Batteries (Total 24960 VAH for 30 minutes Battery Backup). Make:- Numeric/APC/Vertiv.

Providing and fixing following capacity double pole / TP&N sheet metal switch disconnector fuse unit in the existing metal panel board with rewireable type fuses including drilling holes in metal panel, making connections etc. as required.

P/F following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty complete with all accessories including connections, earthing the body etc as reqd.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.I. box etc as required.

Supplying and fixing 10/12 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,IP 65 protection and complete with integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Fixing for laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Providing chemical/ mineral maintenance free aerthing system comprising of copper earth electrode 3 metre length and 17.2 mm outer dia along with 25 Kg earth electrode conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth inspection pit etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus-bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.