Improvement of Distribution system LWSS Aloh Punani in Tehsil Rakkar Distt Kangra (HP)

Amount

Excavation in foundation trenches etc. in earth work, lift upto 1.50mts. Stacking the excavated soil not more than 3 metre clear from the edge of excavation and then returning the stacked soil in 15 centimetre (Fifteen centimetre)layer when required into plinth sides of foundation etc.consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in-charge within all leads and lifts.

Providing and laying cement concrete 1:6:12 (One cement is to six sand is to twelve graded stone aggregate 40 milimetre nominal size) and curing complete excluding the cost of form work in foundation and plinth with in all leads and lifts as per the direction of Engineer-in-charge.

Square rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints in cement mortar 1:6 (One cement is to six sand) within all leads and lifts as per the direction of Engineer-in-charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering strutting and propping etc. with wooden batten and ballies, in all heights of propping and centring below supporting floor to ceiling not exceeding 4 mtrs and removal of the same for insitu-reinforced concrete and plain concrete work in :- In foundation footing bases of columns etc. and mass concrete including plinth beams and columns up to plinth level in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-charge.

In flat surfaces with steel plates such as soffits of suspended floors, roofs, landing and the like floor etc upto all thickness in all leads and lifts as per direction and to the entire satisfaction of Engineer-in-charge.

Stair case with slopping or stepped soffites excluding landing within all leads and lifts complete in all respect as per the entire direction of Engineer-in-charge.

Sides and soffits of beams, beam hunchings, cantilivers girders, bressumers and lintels not exceeding 1 metre in depth within all leads and lifts complete in all respect as per the entire direction of Engineer-in-charge.

Edges of slab and breaks in floor and walls under 20 centimetre in wide within all leads and lifts as per the direction of Engieer-in-charge.

Providing and laying cement concrete 1:2:4(One cement is to Two sand is to Four graded stone aggregate 20 milimetre nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:- Foundation,footings bases of column and the like mass concrete within all leads and lifts as per the direction of Engineer-in-charge

Suspended floors,roofs landing shelves and their supports balconies beams,girders and cantilevers upto floor two level within all leads and lifts as per the direction of Engineer-in-charge.

Stair cases (Except spiral stair case) including landings but excluding preparing the surface & finishing of the nsing up to floor two level within all leads and lifts as per the direction of Engineer-in-charge.

Providing Laying of Tor steel reinforcement for RCC work including bending binding and placing in position including wire upto all floor level as per direction and to the entire satisfaction of Engineer-in-Charge.

Brick work using common burnt clay building brick in foundation and plinth in cement mortar 1:6(one cement :Six sand) with 2nd. Class bricks with in all leads and lifts as per the direction of Engineer-in-charge.

Half brick masonry in common burnt clay building bricks in cement mortar 1:4 ( 1 cement : 4 approved sand) including carriage of of all material within all leads and lifts above floor two level.

Half brick masonry in common burnt clay building bricks in superstructurel upto floor two level in cement mortar 1:4 (One cement is to Four sand) 1st class with in all leads and lifts as per the direction of Engineer-in-charge.

Providing wood work in frames and doors,windows,clearstory windows and other frames wrought framed and fixed in position 2nd. class (Deodar wood) within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing 40 milimetre thick panelled, glazed or pannelled and glazed shutters for doors, window and clearstory window including bright finished/black enamelled iron but hinges with necessary screws in 2nd class deodar wood with in all leads and lifts as per the direction of Engineer in charge.

Providing and fixing wire gauge shutters using galvanised mild steel wire gauge of is gauge designation 85 gauge wire of dia 0.56 milimetre for doors, windows and clerestorey windows including bright finished black enamelled iron hinges with necessary scews 40 milimetre thick of 2nd. class deodar wood within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing 40 x 3 milimetre flat iron hold fast 40 centimetre long including fixing to frame with 10mm diametre bolts nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 (one cement : three sand : six graded stone aggregate 20mm nominal size complete in all respect for door and window with in all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing anodized aluminium Sliding door bolts anodised (250x16 milimetre )clour and shade with nuts and screws complete with in all leads and lifts as per direction of Engineer in charge.

Providing and fixing aluminium tower bolts (Barrel type) anoised transperent or died to required shade with necessary screw complete with in all leads and lifts as per direction of Engineer in charge. 250x10 milimetre

Providing and fixing anodized aluminium handles anodised, transparent or or died to required shade with necessary screw complete with in all leads and lifts as per direction of Engineer in charge. 125 milimetre

100 milimetre

Providing and fixing oxidized M.S Hooks and eye 200mm long screw etc complete with in all leads and lifts as per direction of Engineer in charge.

Providing and fixing oxidized M.S single actng hinges with necessary screws complete with in all leads and lifts as per direction of Engineer in charge. 125mm

Providing and fixing 100mm bright finished brass floor door stopper with rubber cushion to suit shutter thickness complete with in all leads and lifts as per direction of Engineer in charge.

Providing and fixing 12mm thick and 150mm wide palmet with 25mm diameter wooden curtain rod and brackets including with 25x3 mm M.S flat 10cm long and plugs etc 2nd class deodar wood complete with in all leads and lifts as per direction of Engineer in charge.

Providing and fixing 75mm x 60mm rounded hand rail in straight length 1st class deodar wood complete with in all leads and lifts as per direction of Engineer in charge.

Filling in plinth with sand under floors including watering ramming consolidating and dressing with in all leads and lifts as per the direction of Engineer-in-charge.

Stone/ Boulder filling dry hand packed tightly under floor including carriage of material within all leads and lifts as per the direction of Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (1cement : 2 approved sand :4 approved quarry stone aggregate.40mm nominal size) and curing complete excluding cost of centering and shuttering in foundation and plinth including carriage of material within all leads and lifts.

Applying priming coat over new wood and wood based surfaces after and including preparing then surface by thoroughly cleaning oil grease,dirt and other foreign matter,sand papering and knotting with ready mixed paint brushing wood primer pink with in all leads and lifts as per the direction of Engineer-in charge.

Applying two coats of wood preservative on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease dirt and other foreign matter, sand papering and knotting within all leads and lifts as per the direction of Engineer-in-charge.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of all dirt dust and other foreign matter sand papering and stopping with enamel paint other than white with in all leads and lifts as per the direction of Enginer in charge

Applying priming coat over new steel and other metal surfaces after and including preparing then surface by thoroughly cleaning oil grease,dirt and other foreign matter,sand papering and knotting with ready mixed paint brushing with in all leads and lifts as per the direction of Engineer-in charge.

Painting two coats excluding priming coat on new steel and other metal surfaces with ready mixed paint and brushing to give an even shade including cleaning of all dirt,dust and other foreign matter with in all leads and lifts complete in all respect.

6 milimetre (Six milimetre) thick cement plaster to ceiling in cement mortar 1:3 (One cement is to three sand) within all leads and lifts as per the direction of Engineer-in-charge.

15 milimetre( Fifteen milimetre) thick cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises internal rounded angles chamfers and/or rounded angles not exceeding 80 milimetre in girth and finished even and smooth in cement mortar 1:3 (One cement is to Three sand) within all leads and lifts as per the direction of Engineer-in-charge.

White washing with lime on undecorated wall surfaces two coats to give and even shade including thoroughly/brooming the surface to remove all dirt dust mortar dirt and other foreign matter in ceiling/or sloping roofs within all leads and lifts as per the direction of Engineer-in-charge.

Distempering( two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface to give and even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer.

Providing plinth protection 75 milimetre thick (unconsolidated ) bed dry brick/ stone aggregate 40 milimetre nominal size) wil rammed and sonsolidated and grouted with fine sand including preparation of ground within all leads and lifts as per the direction of Engineer-in-charge.

Providing plinth protection 50 milimetre thick in cement concrete 1:3:6(One cement is to three sand is to six graded stone aggregate 20 milimetre nominal size)including finishing the top surface of concrete smooth within all leads and lifts as per the direction of Engineer-in-charge.

Providing and laying four courses water roofing treatment with bitumen filt over roofs consisting of 1st and 3rd courses of blow or and residual bitumen applied hot at 1.45 kg/ sqm of area for each course 2nd courses of roofing felt type 3 grade 1 ( hesion base self finished bitumen felt ) 4th and final course of stone grit 6mm and down size of pea size gravel spread at 6 cu- dm or 0.006cum/ sqm welding preparation of surface excluiding gradng complete within all leads and lifts as per the direction of Engineer-in-charge.

Making khuras 45x45 cm with average minimum thicknesss of 5cm cement concrete 1:2:4 (1 cement:2 Sand : 4 graded stone) agg. 20mm nominal size) finished with 12mm cement plaster 1:3( 1 Cement 3 Sand) and a coat of neat cement rounding the rdge and making and finishing the outlet complete within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing on wall face C.I rain water pipe including fitting the joints with span and cement mortar 1:2 (1Cement: 2Sand) 100mm diameter complete within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing MS holder bat clamps of approved design to C.I or S.C.I pipes embbeded in an including cement concrete block 10x10x10cm of 1:2 (1 cement : 2sand 4 graded stone agg. 20mm nominal size ) and cosst of holes and making good the wall etc 100mm dia for CI pipe complete within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing om wal face C.I accssories for rain water pipes including filling the joints with spun yarn soaked in neat cement sullary and cement mortar 1:2 ( 1 Cement : 2Sand ) . complete within all leads and lifts as per the direction of Engineer-in-charge. C.I Head Flat 100mm dia

C.I Plain shoe 100mm dia.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall 15x22cm in cement mortor 1:6 ( 1Cement :6 Sand) and inside plastring with Cement Palstring 1:3 (1Cement : 3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 ( 1Cement : 5 Sand : 10 gradded stone aggregate nominal size ) of 40 mm nominal size and 7.5 cm cement concrete 1:2:4 ( 1Cement ;2 Sand : 4 gradded stone aggregate nominal size 20 mm ) and finished with a floating coat of neat cement complete as per standard design.

Providing and fixing mild steel grills of required pattern in wooden frames of windows etc. mild steel flats square or rounded bars with required bolts and nuts or by screws plain grill within all leads and lifts as per the direction of Engineer-in-charge. (Plain grill).

Tikam Ram (BID ID -445657)

RANDEEP SINGH GOVT CONT (BID ID -445820)