PROVN OF DHOBI GHAT AND SOLAR WATER SYSTEM FOR HOT WATER SUPPLY ALONGWITH ADDITION/ ALTERATION OF CIPHER SECTION INCLUDING INSTALLATION OF NFS AT 2 WEU KHAMBALIYA AIR FORCE STATION UNDER GE (AF)JAMNAGAR NO.2.

Amount

Surface excavation n.exc 30 cm deep and avarage 15 cm deep and getting out in soft / loose soil.

Excavation in trenches n.exc 1.50M wide & n.exc 1.50M deep for foundation etc or for shafts wells cesspits ,manhole pier holes etc n exc 10 sqm on plan and n exc 1.5 m depth and getting out in hard/dense soil.

M &L for moorum/red bajri filling in floors or paving laid in layers n.exc 15cm thick, spread, leveled and rammed including watering all complete all as directed .

M&L for hardcore of broken stone boulder of gauge n exc 63 mm, deposited, spread and leveled in layers n exc 15 cm thick watered and rammed to true surface.

Returning,filling in including spreading ,levelling,watering and well ramming in layers not exc 25 cm

Removing excavated material n.exc 50.0 mtr and depositing where directed at a level n.exc 1.5M above the starting point all as specified and as directed by Engineer-in-Charge.

M&L Cement Concrete( 1:4:8) type D2 (40mm graded )in foundation filling and mass concreting.

M & L for precast cement concrete (1:3:6) (using 20mm graded stone aggregate) solid building blocks exe 10 cm thick, in width (with plain or inter locking joints as directed) setting in CM 1:6 complete in wall or pillars all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces

M&L RCC M-30 using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M & L for steel reinforcement TMT bars 10mm dia and over cut to length and bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips all as specified and directed.

All as per item No11 above but 5mm dia and over upto and including 8mm dia as in stirrups spacer and binders confirming to Fe410-s or Fe-410Q

M & L for 50 mm thick cement concrete type B0 1:2:4 (using 12.5 mm graded aggregate) as in flooring all as directed.

S&F framed work such as grills, framed guards bars and similar work conforming to 290 Gde F-165 complete all as specified & directed.

M&L for 75mm thick cement concrete (1:3:6) type C-1 (using 20mm graded stone aggregate) as plinth protection finishing even and smooth without using extra cement and making joints and filling with bitumen sand mastic including necessary form work

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:6) finished even & smooth (without using extra lime or cement).

M&L Rendering 5 mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling

M & L Rendering 15 mm thick in CM 1:4 in two coats on brick work or concrete surface incl finished fair and even without using extra cement incl mixing of water proofing compound in second coat as per manufacturer instruction all as specified and directed . Note :- Supply only Integral WPC will be measured and paid separately

Supply only liquid water proofing compound

M&L for applying three coats of white wash on new plaster Ceiling surface including preparation of surface.

M & L three coats of white wash on newly plastered wall surfaces including preparation of surfaces.

M&L for two coats of synthetic enamel paint over a coat of zinc chrome primer including prepration of new steel surfaces exc.10cm in width or girth complete all as specified and directed.

M&L for factory made flush shutters,35mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides, with 0.90mm thick decorative laminate type 1 of surface finish, colour as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

Supply & Fixing IInd class hard wood plain solid straight chowkats and frames wrought, framed, rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

M&L for preparation of new wooden surfaces of any description exc 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of primer.

Supply & Fixing 100mm long cold rolled, mild steel butt hinges medium weight complete all as specified and directed.

Supply & Fixing 200mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

Supply & Fixing 300 mm long aluminium alloy anodized sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section etc complete all as specified and directed.

Supply & Fixing 150 mm long extruded aluminium alloy handle fabricated type anodised complete all as specified and directed.

S&F for powder coated, anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F Aluminium anodized window shutter including , aluminium handle, tower bolt hinges all made of aluminium section of adequate size and all member of window of size 44.45 x 44.45 mm and jointing cleats , all aluminium members shall be made out of 1.60mm thick aluminium sheet/section). Note :- (i) Centre moving door shutter with floor. Bearing hinges/sliding door hinges door set complete shall be deemed to be included in the quoted rate. (ii) Glass and PVC paneling, teak shade design shall be measured and paid for seperately under relevant items.

S&F 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane all as specified and as directed.

S & F mild steel hold fast & similar articles confirming to Fe-290 Gde E-165.

M & L PCC typeC-1,1: 3:6 (20mm graded stone aggregate) for cills,hold fast etc including necessary form work.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for Preparation of new plastered/concrete surfaces of walls and applying two coats of exterior acrylic emulsion (weather proof treatment) over one coat of primer, complete all as specified and as directed ( The tint and shade be as approved by the GE) in any height including necessary scaffolding etc complete all as specified and as directed.

M&L for RCC (design mix) M-30 for beams, cantilevers, bressummers, lintels over 1.5 m span including necessary form work

Preparation of new plastered surfaces of wall over a coat of chalk putty 2-3 mm thick wherever necessary & applying two coats of oil bound distemper over a coat of primer on walls.

M&L for cement concrete 100 mm thick type D2, 1:4:8 (40 mm graded aggregate) as in sub base of floor/hardstanding.

M&L for sand filling under floors or in foundation or over concrete surfaces all as specified and as directed

M&L machine pressed precast concrete interlocing paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and no pigment.

S&F sound proof wall panelling of solid PVC foam profile having 100 mm to 200 mm wide tongue and groove 4 mm thick panels with 7 to 8 mm thick ribs of approved shade and pattern. Framing shall be made from solid PVC foam batten of size 35 mm x 17 mm , placed horizontally at 45 cm c/c with solid PVC foam corner all around. fixing shall be done with screws of size 19 mm x 6mm including necessary sealant etc,complete all as per manufacture's instructions and directed.

S&F 18/19 mm thick perforated particle board/tiles for insulation and accoustic purposes, 60 x 60 cm in size, fixed with nails to frame work or with staples on snap grid.

S&F anodised aluminium snap grid frame work for false ceiling all as specified.

S&F of hanger 6 mm dia G.I. (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long complete all as specified.

Dismantling of floor hearth or wall tiling including bedding (but not backing) and taking rubbish off the premises all as directed.

Material and labour for light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Roughening of cement surfaces by picking, sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 Kg of cement per sqm complete.

S& F Mild steel hand rails , half round or other steel section or core for wooden hand rail straight portion , drilled and counter shunk for balusters running bar, or door , balusters nosing to steps including embedding in concrete screwing etc. Wind ties for roof including sccuring bolts , posts and struts in fencing including cutting tops to shape as directed , drilling holes notching for wire etc, flat iron filtets for securing wire mesh etc, including all necessary drilling, bolting or reviting , etc similar and work confirming to Fe - 290 Gde E - 165 complete all as specified and directed

M&L for PCC (1:3 :6 ) type C2 (using 40mm graded crushed stone aggregates) as in foundation filling in mass concrete.

Cutting holes in brick walls not exc. half brick wall in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required

Preparation of old plastered surfces of walls over a coat of chalk putty 2-3 thick and applying two coats of OBD over a coat of primer on walls

S&F decorative laminates type 1, of surface finish, colour and pattern as approved, fixed with laminate both sides, approved adhesive as per manufacturer;s instructions of 0.9 mm thick.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) Exc 1.5 sqm but n. exc 4 sqm each and refixing the other opening.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified.

Dismantaling of stone slabs and tiles of any description or thickness laid dry or laid dry and pointed in floors, aprons etc.

Dismantling of Cement Concrete (Reinforced) of any description and in any Position not otherwise specifically provided for and removing the same from Site(s), complete all as specified and as directed.

Demolition of brick work or stone boulder/PCC block masonry built cement mortar including removing debries to out side MD land

M&L for preparation of old decorated surfaces in walls soffits, facia roof and applying, one coat of weather proof acrylic based emulsion paint (100% acrylic) as per manufacturers instructions etc complete all as specified and directed by Engr-in-Charge. Make :- Nerolac(Exel), Asian Paint (Apex ultima), Dulux (weather shield water proof), Berger (weather coat all guard).

Preparation of old plastered surfaces, applying 2 coats of white wash on ceiling

M&L preparation of old steel surfaces over 10cms width or girth, and applying two coats, of synthetic enamal paint

Supply and lay LT XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cable heavy duty 1100 Volts grade with stranded aluminum conductor of size 35 Sqmm, 3.5 Core all as specified & directed

Supply, install, Testing and commisioning of Front load Washer Extractor Machine with Conntected accessories of 30 KG capacity containing automactic features like auto timed, auto reverse , auto temperature control etc , VFD speed control to achieve wash and spin RPM, Auto Chemical despenser, Penumatic cylinder to lock the door electro mechanically so that it opens only after the complete operation is over including necessary foundation work etc of following size and specification all as per manufacturer & directed :- (i) Type :- Front Load SS 304 Body (ii) Capcaity :- 30 KG (iii) Cylinder size :- Dia 900mm x 500mm (iv) Cylinder volume :- 375 Ltr (v) Door opening in :- dia 500 mm (vi) Water inlet size :- 1.5" (vii) Drain size :- 2.5 " (viii) Motor :- 7.5 HP (ix) Wash spin :- 36 RPM (x) Extract spin :- 670 RPM (xi) Over all dimensions : 1220 x 1250x 1730 (xii) Net weight :- 950 KG Make :- IFB / SCHULTHESS / WHIRLER / VETECH

Supply, install, testing and commissioning of front load type Tumble drier having stainless steel inner basket containing automactic features like auto timed, auto reverse , auto temperature control with solenoid valves etc , High energy efficient with double wall glass - wool insulation & lint screen , Two seperate motors for drive & suction blower of following size and specification all as per manufacturer instructions and directed (i) Capacity :- 30 KG (ii) Heating :- Electrical (iii) Basket diameter :- 950 mm (iv) Basket depth :- 950 mm (v) Basket Volume :- 670 Ltr (vi) Motor Capacity :- 2 HP ( 1 + 1 HP) (vii) Air Exhaust size :- 10" X11" (viii) Door opening :- 650 mm dia (ix) Electrical requirement :- 18 KW (x) Over all dimensions : 1050 x 1540x 1980 mm Make :- IFB / SCHULTHESS / WHIRLER / VETECH

S & F Vacuum Table with Boiler & iron 4 KW Cap steam Out put 4 Kg / Hr all as specfied and directed with following specification :- (i) Table TOP padded with imported silicon padding. (ii) Strong welded construction. (iii) Thermostatically controlled stainless steel table heater. Extended exhaust duct with lighting device. (iv) Powerful Suction through centrifugal blower activated by spring loaded full length foot pedal working in conjunction with sturdy micro switch. (v) Silicon iron stand protects ironing and Teflon soles with stand up to 150 degree centigrade of temperature. (vi) Covered with silicon foam with heat proof cloth. Electrical Steam Boiler Pressure Vessel: (vii) SS Heavy Duty Electrical Heaters. (viii) Electrical Solenoid Steam Release Safety Valve. (ix) SS Water Storage Tank Make :- IFB / SCHULTHESS / WHIRLER / VETECH

S & F SS 304 grade trolley size -1150 x 750 x 600 mm with big caster wheel with bearing for smooth movements all as specified and directed Make :- IFB / SCHULTHESS / WHIRLER / VETECH

Supply and fixing cast iron sluice valve for 80mm bore pipe with flanged ends, PN-1.6, ISI Marked with gasket nuts, bolts & washer complete all as specified & directed.

S&F Pipe galvanized medium grade of size 80mm bore etc including all fittings laid on wall/ floor complete all as specfied and as directed

All as per item No 69 above but of size 50mm bore

All as per item No 69 above but of size 40mm bore

All as per item No 69 above but of size 25mm bore

S&F stop valves, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of size 25mm bore complete all as specified and as directed by Engr-in-charge.

All as per item No 73 above but of size 40mm bore

All as per item No 73 above but of size 50mm bore

M&L Sub main wiring using two single core PVC insulated FR cable 4 sqmm copper conductor multi stranded and 2.5 sqmm copper conductor insulated cable as earth wire drawn through and including PVC conduit. Note: Two runs of 4sqmm copper cable & one run of 2.5 sqmm copper cable and 25mm dia PVC conduit will be measured as one unit.

M&L Sub main wiring using two single core PVC insulated FR cable 2.5 sqmm copper conductor multi stranded and 1.5 sqmm copper conductor insulated cable 25mm dia as earth wire drawn through and including PVC conduit. Note : Two runs of 2.5 sqmm copper cable & one run of 1.5 sqmm copper cable and 25 mm dia PVC conduit will be measured as one unit.

M&L Sub main wiring using two single PVC insulated FR cable 6 sqmm copper conductor multi stranded and 4.0 sqmm copper conductor insulated cable 25 mm dia as earth wire and drawn through and including PVC conduit. Note : Two runs of 6 sqmm copper cable & one run of 4.0 sqmm copper cable and 25mm dia PVC conduit will be measured as one unit.

S&F submain wiring using four run PVC insulated FR Copper conductor 10 sqmm drawn through and including rigid non metalic PVC conduit of size 25 mm dia exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook including all fixtures /fittings fixed on wall/ceiling with saddles PVC with earth continuity wire copper conductor PVC insulated unsheathed 6 Sq mm all as specified and directed.

M & L for distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 4 way with 200 Amps rated copper busbar, neutral bar, earth bar, IP 43 protection, single pole and neutral 250 Volts, flush to wall complete all as specified and directed. Make : Legrand Model: 507610 or equivalent in simens / Schnieder (Acti-9).

S&F MCB four pole 40 Amp, 10 KA, 415V complete all as specified and directed

M&L for circuit breaker single pole & neutral 240 volt C curve 10KA (32&63) Amps capacity IP 20 complete all as specified and directed.

M&L for Circuit breaker triple pole & neutral 415 volt C curve 10KA, 63Amps capacity IP 20 complete all as specifid and directed.

M&L for Circuit breaker single pole, 5 to 32 Amp 240 volt B curve 10 KA, IP 20 complete all as specified and directed.

M &L Earthing complete with galvanised GI earth plate electrode 600x600x6.3mm thick,burried directly in ground (earth pit not less than 2.25mtrdeep below GL) with top edge of the plate n.less than 1.5mtr below normal.GL surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all round the plate using 4mm dia GI wire as earth wire electrode welded and revetted to earth plate at one end connected to main DBs of Bldg at another end GI earth wire encased in and including 15mm dia GI light grade pipe through upper end of earth plate upto main DB of bldg with 20mm bore GI pipe light grade as water pipe from earth chamber to upper edge of earth plate MS funnel with wire mesh fixed on water pipe and Provn of PCC pit in PCC 1:2:4 type B-1 chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type BI duly reinforeced with MS bars 8mm dia @ 150C/c with both ways complete with lifting handle all as shown in electrical plate no 5 of SSR of part-I complete all as specified and directed by Engr-in-charge.

S & F industrial type plug & socket board SP & N enclosure with 2 pole and earth metal plug & socket complete with 10 Amp MCB SP, Make : Legrand cat part No : 607841 or equivelent of Havell's , Schneider etc

S & F industrial type plug & socket board TP & N enclosure with 4 pole and earth metal plug & socket complete with 63 Amp MCB TPN, Make : Legrand OR equivelent of Havell's , Schneider etc

Supplying and laying reinforced precast concrete cable cover, class LV Type2, flat size 300mm x180mm x 40mm thick all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

Taking down carefully (copper/aluminum) unsv point wiring complete of any type (batten/surface conduit or concealed) for light point, fan point, bell point, socket point or power point including fixture and fitting such as switches ceiling roses, pendants, regulators, sockets, light fitting etc. removing material to store for keeping in sate custody or for taking credit (credit of above items should be made as per conditions seperately) and making good the disturbed surfaces of wall/ floor or ceiling to match with existing surface and finishing the surfaces with distemper/ white washing/ colour washing as per existing complete all as spacified and directed.

Taking down carefully by unscrewing from main switch boards/cut out boxes/MCB DBs/ complete sealing the cable end and making good disturbed surface by walls etc.

Taking down carefully by unscrewing from fitting and fixtures such as ceiling fittings, bulk head fittings,tube light fittings, street light, flood LED lights etc all as specified and directed.

M&L for Point wiring with PVC insulated and unsheathed multistranded FRLS copper conductor single core 1.5sqmm (nominal area) cable using approved colour code as per IS drawing in and incl PVC concealed conduit of suitable as per IS with all accessories suitable for modular type fitment including provision for fixing of modular flush boxes/ concealed of suitable size complete alongwith 1.5 sqmm as continous earth wire connected to common earth and earth dolly complete all as specified and making good distrubed surfaces of wall. floor or ceiling with plaster and finishing the surfaces with distemper/white washing/ colour washing to match with the plaster and finishing the surfaces with distemper/ white washing/ colour washing to match with the existing surface complete as specified and as directed by Engr-in-Charge

One light point/ Fan point controlled by one switch

One 3 Pin socket outlet 5Amps on the same board with other switches

One 3 pin 5Amp socket out let controlled by one switch on independent board

M&L for Point wiring for power point with PVC insulated and unsheathed multistranded FRLS copper conductor single core 2.5sqmm (nominal area) cable using approved colour code as per IS drawing and incl PVC concealed. Conduit of suitable as per IS with all accessories suitable for modular type fitment including provision of fixing of modular flush/ conceded boxes of suitable for modular type fitment including provision for fixing of modular flush/ Concealed boxes of suitable size and thickness as per IS complete alongwith copper earth wire PVC insulated & unsheathed multistranded (FRLS) copper conductor cable of size 2.5 sqmm as continous earth wire connected to common earth and earth dolly complete all as specified and making good disturbed surfaces of wall, floor or ceiling with plaster and finishing the surfaces with distemper/ white washing/ colour washing to match with the existing surface complete as specified and as directed by Engr-in-Charge.

All as per item No 91 above but 4.0 Sqmm multi- stranded copper conductor PVC insulated unsheathed fire retardant low smoke, cable and 4.0 sqmm multi- stranded copper conductor PVC insulated, unsheathed fire retardant low smoke. Cable as continous earth wire connected to common earth dolly for 15 Amps multipurpose socket outlet on independent board. controlled with one way switch.

M&L for ceiling rose, 2 to 3 terminal PVC/ polycarbonate, isolated body type suitable for AC 230volts.

M&L for Modular metal Flush box as per site requirement.

1 Module

2 Module

3 Module

4 Module

6 Module

8 Module

M&L for Modular metal flush box as per site requirement.

1/2 Module

3 Module

4 Module

6/8 Module

M&L for modular switch 1 way 6 Amp 1 Module Make : Legrand Arteor Series Cat Part No : 573400 or equivalent of Make Kolors/Crabtree

M&L for modular switch 1way 16/20 Amp 1 Module Make : Legrand Arteor series Cat Part No 573410/Kolors (Krest white) Crabrtee

M&L for modular socket 6A 2/3 Pin universal2 Module Make : Legrand Arteor series Cat Part No 573470/Kolors (Krest white) Crabrtee

M&L for Modular socket 6A 2/3 Pin Ucombined 2 module Make : Legrand Arteor series Cat Part No 573471/Kolors (Krest white) Crabrtee

M&L for modular socket 16A/6A 2/3 Pin combined 2 module Make : Legrand Arteor series Cat Part No 573471/Kolors (Krest white) Crabrtee

M&L for modular fan step regulator 100 watt 2 module Make : Legrand Arteor series Cat Part No 573416/Kolors (Krest-white) crabtree

S&F energy efficient LED tube light fitting integrated batten type with built in LED chip & integral LED driver 21 watt, channel housing & diffuser of length 1200 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position& connecting complete all as specified and directed by Engr-in-Charge. Make : Philips cat part No BN 021C LED120S PSU CDL/NW GR (6500K) or equivalent in HAVELLS/WIPRO

S&F energy efficient LED tube light fitting integrated batten type with built in LED Chip & integral LED driver 10 watt, channel housing & diffuser of length 600mm (approx) with all accessories, fixing arrangement internally pre-wired fixed in position & connecting complete all as specified and directed by Engr-in-Charge. Make: Philips cat No BN 021 LED 10S (6500K) or equivalent in Havells/Wipro

S&F surface/ wall mounted recessed LED downlight for mltipurpose utility capacity 15W with inbuilt electrionic driver, 2000 Lumen output, surge protectionof 2.5 KV with vide voltage protecion range 140 270V. Pressure die cast aluminium housing for effective thermal management and high transmission facto PMMA diffuser for better performance 6500CCT (K) complete all as specified and directed by Engr-in-Charge. Make: Wipro Cat No LD 90-191-XXX-65-XX++ or equivalent in Havells/Philips

Supply an fix in repair LED lamp 5 watt cap complete all as specified and directed. Make: Wipro Tejas Cat part No N55001 or equivalent in philips/havells/bajaj

Supply and fix in repair 35W LED building security light luminaire complete with pressure die cast aluminium housing and primatic poly carbonate cover to ensure better unformity of light distribution fixed on bldg wall surface including provision of GI pipe bracket complete with clamp nuts bolts and washers and making good the disturbed surface of wall complete all as specified and directed by Engr-in-Charge. Make : Philips cat part No.BPR 050 LED 036 CW R1 MF PC S1 PSU GR or eqqivalent in havells/wipro/bajaj

Taking down carefully (copper/aluminium) submain wiring complete with all fittings such as switches sockets pendants etc complete and making good disturbed surface of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surface with distemper white washing/ colour washing to match with the existing surface complete all as specified and directed.

M&L for distribution board (DB), double door (CRCA sheet) dust and vermin proof SPN 8way with 100 Amps rated copper busber neutral bar, earth bar and cable ties for cable management, reversible door for IP 43 & IP 54, Single pole and neutral 250 Volts, flush to wall complete with IP 54 protection complete all as specified and directed. Make : Legrand model: IP 54 IK 09 507641 Exinox or equivalent in L&T (Hager)/Schnieder (Multi-9).

M&L for distribution board (DB), double door type as per IEC 61439-3 made out of sheet metal enclosure (CRCA Sheet) dust and vermin proof MCB DB, TPN 4 way with 250 Amps rated copper busbar, 415 Volts with in built MCCB 160 Amps, 10KA 01 No 2neutral bar and 2 earth bar IP 54 protection cable ties for cable management (fully insulated busbar and shrouded neutral bars) reversible door for IP 43 & IP 54, flush mounting to wall, including provision of MCB SP 6 to 32 amp 10KA 12 nos complete all as specified and directed . Make : Legrand Model : No. 507750 Ekinox DPX 160MCCB IK-09 or equivatent in L&T (Hager)/ Schnieder (Multi-9).

Supply and install split in wall air conditioner 1.5 ton capacity with inverter technology with general specification as under (i) Energy efficient (ii) Cooling only (iii) Stabilizer free operation suitable for 220-240V, 50Hz operation with rated power input 1420 watts complete with condensing unit, connecting pipe and cable etc. complete with all fitment accessories for outdoor unit, cordless remote with wall holder. The technical specification of air conditoner is (a) Star rating - 5star BEE rating (b) ISEER (kwh/kwh) 4.5 minimum as per BEE (c) Condenser Coil- Copper (iv) Compressor- Dual Rotary.

M&L for earthing with SAFE EARTHING ELECTRODE (S.E.E) conforming to IS : 3043-1987 with zinc coated earthing electrode with coating thickness of 100 microns using pipe in pipe technology method with 3 Mtr long, 42mm inner dia and 76mm outer dia GI rod connected with and including 25mm x 3mm size GI strip upto 7.5mm fixing of electrode by boring 150mm dia hole upto 3.30 meter depth in any type of soil with mechanical apparatus, returming filling with back fill compound (BFC) 25*2KG compound bags including GI tubing 40mm dia with necessary fittings light grade as protection to GI strip complete with FRP earthing protection chamber along of size 420 mm x 420 mm at top, 340mm x 340mm at bottom, height 210mm with FRP chamber cover and including FRP Earthing result display board of size 254mm x 380mm made out of plastic material showing the information replated to type of earting, earthing result due date of tesing etc along with fixing stand 610mm height made of angle iron as per manufactures instruction and as specified and directed by Engr-in Chagare.

Supply install, Testing and commissioning of solar cum electric Water heating system (Evacuated tube collector) based on direct transfering of heat, thermosyphon circulation of capacity 200 LPD suitable for bathing purpose consisting of following components all as specified and as per manufacture design and comprision of the following. (a) Evacuated tube collector assembly suitable for 200LPD (b) Stainless steel hot water tank with a heat resistant protective coating and insulated with polyurathane from with scarificial anode and electric back up of suitable capacity (c) Collector stand (d) Tank stand assembly complete all as directed (e) Piping from cold water supply tank to hot water tank and to collector including connecting collectors (f) Hot water pipe from collector assembly to hot water tank making connection to pipe fixtures to the tank and lagging to pipes all as specified (g) Open vent pipe for pressure build up (h) Instrument (one temp guage, strainer & water metre(j) Make up tank and anti freeze sloution (k) Gate valve of suitable size for cold and hot water piping (l) Complete arrangement for mounting to collector panels complete all as specified and as directed by Engr-in-Charge. Make : V-guard/ Inter solar/Tata BP solar India Note : (i) Cost of item include PCC work,if any, required at site, Cutting of existing pipes for connection (ii) Nothing shall be paid extra for any other work required in addition as mentioned above . (iii) Make of gate valve, piping and other instruent shall be as per approved list of makes.

Material and labour for fabrication of staging for cold water tank using cross arms. Bracings, supports clamps and back plates fabricated from structural steel sections including nuts, bolts washers, welding bending cold or hot, drilling holes for bolts, in any shaps of size as indicated or directed and inclusive of one primer coat and one finishing coat of paint complete all as specified and as directed by Engr-in-Charge.

S&F CPVC (Chlorinated polyvinyl chloride) schedule 40 confirming to ASTM D-1785 with threded ends pipes, 20mm bore with nominal outside diameter 26.5mm and wall thickness of 2.87mm suitable for working pressure of 33.10Kgf/cm2 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including brass threaded CPVC fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed .

S&F CPVC (Chlorinated Polyvinyl chloride) schedule 40 confirming to ASTM D-1785 with threded ends pipes, 25mm bore with nominal outside diameter 33.27mm and wall thickness of 3.38mm suitable for working pressure of 31.0Kgf/cm2 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including brass threaded CPVC fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed.

S&F Bronze gate vale class-2 for 25mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed ISI marked conforming to IS 778, 1984, complete all as specified and directed. Make : LEADER/ L&T/ZOLOTO

S&F bronze vertical check valve (Non return valve) 25mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, complete all as specified and directed. Make : LEADER/L&T/ZOLOTO

Vijay Construction Co