REPAIR /REPLACEMENT TO ROOF SHEETS, BRICKS WORKS, IRON DOOR/GATES, HARDSTANDING, PARTITION WALL, ROOF CEILING, TILING, JOINERY, PLUMBING, ROOF TREATMENT AND POST ANTI TERMITE TREATMENT TO VARIOUS LABS/BUILDING AT METCALFE HOUSE AREA UNDER GE I RND

Amount

M & L for providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.50 Ltrs per Sqm of the vertical surfaces of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

M & L for antitermite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 Ltres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

M&L for Anti-termite treatment of side in skirting of existing floors using emulsion @ one litre per hole,300mm apart including drilling and pluging 12mm dia hloles with cement mortar 1:2(1cement:2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for Anti-termite treatment at point of contact of wood work by chemical emulsion(in oil and kerosene based solution) @ 0.5 litre per hole by drilling 6mm dia hloles at a downward angle of 45 degree at 150mm centre to centre and sealing the same. with cement mortar 1:2(1cement:2 coarse sand) to match the existing floors complete all as specified and directed.

M & L for treating the soil along the external perimeter of building at the rate of 2.25 Ltrs of anti termite emulsion per meter of the perimeter wall complete all as specified and directed..

Notes for serial No. 1 to 5 :- 1. External & Internal perimeter chemical pesticides would be injected by drilling 12mm holes at the junction of wall and floor in external, internal perimeter, construction joint of the building, at a distance of 30cm at about 45 dgree angle in case of masonay foundation chemical emulsion of up to 0.5 liter or till refusal would be applied in each hole. 2. Wood work : Chemical pesticides would be injected in holes drilled at downward angle of 45 degree at the junction of wood work and concrete. Works like door, window frame wardrobe, wooden paneling on staircase. wall false ceiling etc would be treated. Chemical pesticides upto 0.5 liter or till refusal would be applied in each hole. 3. Other areas : Chemical pesticides would be applied around electric pipe, telephone cable utility pipe entering the builing which are potential source of entry points tothe building. 4. Chemical used for ATT shall be chlorophyriphos 20% or lindane approved by GE (I) R&D Delhi.

Taking down cement plaster from brick or stone wall etc including racking out joint, hacking for key scrubing down with water etc complete all as specified and directed.

Material and labour for 15mm thick rendering on brick work or concrete surfaces in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 15 mm thick rendering on brick work or concrete surfaces in CM (1:4) mixed with WPC as per manufacturers instructions finished even and smooth without using extra cement complete all as specified .

Material & labour for 10 mm thick plaster in CM (1:3) as in roof slab / soffits of slabs/Chajja/ Sunshade etc finishing the plastered surface even & smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of newly plasterd surface of wall and applying two coats of cement base paint of approved shade/tint over one coat of priming etc complete all as specified and directed.

Material and labour for two coats of oil bound distemper on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

Material and labour for applying two coats of distemper oil emulsion over two coat of wall care putty 2 mm thick (1mm thick each coat) on wall including preparation of surfaces complete all as specified and directed.

Demolition of brick work built in cement mortar of any description complete all as specified and as directed.

M&L for brick masonry with sub class old size `B` brick straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

All as per item No 14.00 above but except bricks

M&L for brick work with sub class `B` brick straight or curved on plan to any radius in half brick thick wall built in cement mortar (1:4) complete all as specified and as directed.

M&L for Rough cast plaster including 15mm thick rendering in CM (1:3) on brick work or concrete surfaces complete as specified in SSR pat -I clause 14.22 complete all as specified and as directed.

M&L for two coats of acrylic exterior emulsion weather proof paint of any tint including priming with alkali resistant primary paint on external plastered surfaces of wall complete all specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of cement base paint of approved shade/tint over one coat of priming complete all as specified and as directed.

M&L for applying two coats of oil bond distemper over two coat of putty (min thichness of each coat 1.00mm) on wall etc complete all as specified and directed.

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately) Note:- 1. Rate also includes necessary iron scaffolding to carry out stone grit plaster work upto a height G+6 floor.

Material & labour for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified and directed.

M&L for complete removal of exisiting tratement, cleaing the surface with emery paper 180 and applying one coat of primer and subquently with putty for making the surface soomth for receving two coat of base paint (tint) incldung two coat textured wall painting with premium acrylic (textured) emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grms/ltrs of approved brand with two protective coat and as per manufacturer instruction complete all as specified and directed.

Demolition of PCC of any description and in any position not otherwise specifically provided complete all as specified and as directed.

M&L for cement concrete (1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for PU coated pre-polished coloured chequered cement concrete tiles 30cm X 30cm X 25mm thick, with white cement and pigments, set, jointed and pointed in neat cement slurry in floors over 20mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 10mm thick anti skid pavement tiles (heavy duty) of area n.exc 0.18 sqm each of approved colour & shade & antiskid finish set and jointed in neat cement slurry and pointed in white cement & pigment to match laid over & including 20mm thick screed bed in CM (1:4) complete all as specified & directed

M&L for PCC type C-1 (1:3:6) (using 20mm graded stone aggregate) as in coping including water through and the like weathering, slightly rounded or chamfered angles and throating including formwork complete all as specified and as directed.

M&L for plain cement concrete, type B-1 (1:2:4) (using 20mm graded stone aggregate) complete & broom finish as in floor/ path/sub base complete all as specified and as directed.

Material and labour PCC (1:3:6) Type C-1 (20 mm graded stone aggregate) as in plinth protection/path 75 mm thick laid in bays including finishing the concrete surface even and smooth without using extra cement complete all as specified and directecd. Note: The unit rate quoted shall be deemed to include for providing the concrete in alternate bays n exc 3 mtr long with 12 mm wide and 50 mm deep joint between the bays which shall be filled with mastic filling with hot bitumen VG-10 and 1:2 mix by volume.

S&F factory made cement concrete kerb stone, finished surface of size 20cmx30cm, dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar 1:6 and struck flush etc including demolition of old broken kerb stone and removing of same out side MoD land in low lying area complete all as directed.

M&L for applying two coat of synthetic enamel paint over concrete /plastered surfaces along with preparation of old surfaces of any description over 10cm width or girth complete all as specified and as directed.

M&L for 80mm thick machine pressed pre-cast PCC coloured designer inter locking paver block with grey cement and no pigment any shape & size confirming to IS-15658 -2006 M-40 grade including 40mm thick sand cushioning layer complete all as specified and as directed.

M&L for precast concrete coloured designer interlocking paver block any shape and size confirming to IS-15658 - 2006 of 60mm thickness M-35 grade with grey cement and no pigment laid over 40 mm thick sand cussioning complete all as specified.

Dismantling structural steel work including doors, gates, angle post but excluding framed truss etc complete all as specified and as directed.

S&F MS framed work as in doors or gate of angle or other section with gusset plates rails braces etc complete drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hooks and pintle hinges or steel hanging door fitting and hanging also fastening and fixing complete all as specified and as directed.

S&F MS plain black sheet in steel gates etc cut to size holes punched, including screw clout nails riveted & welding etc (thickness of sheet 1.60mm) complete all as specified and as directed.

S&F framed work such door, grill railing, cattle trap on open drains using mild steel angle iron, framed guard bars; barred iron doors; ladders; framed balusters; wall ways; railings; framework of water tanks and similar work, MS flats of sizes as directed with and including provision of MS hinges and MS Hold fast fixed complete all as specified and as directed.

S&F structural steel work in tubular truss for pillar/post/rafter/purlin with frame work or frame work for ACP board with special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240 complete all as specified and as directed .

M&L for preparing new steel surfaces over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat or red oxide primer complete all as specified and as directed.

S&F in repair Fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc complete all as specified and as directed.

S&F in repair Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550MPA as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.

S&F in repair polycarbonate Fibre glass reinforced translucent corrugated sheeting with three layer and side lap fixed with coach screw and washer in roof, wall incl fixing on G+5 top roof etc complete all as specified and as directed.

S&F Rolling shutters 1.25mm thick laths , without ball bearing, as specified including top cover, an anchoring rod, haps and staple and one shop coat of primer, erected in position as indicated, complete: push pull or manual type complete all as specified and directed.

S&F Safety lever lock mild steel with 4 levers for rolling sutter complete all as specified and directed.

S&F ball bearing for rolling shutter complete all as specified and directed.

S&F for Collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets,complete all as specified and directed.

Dismantling interlocking tiles of any thickness and any shape including refixed/re-laying on same portion after cleaning the tiles in all respect over and including 40 mm thick sand cushioning compacted all as specified and directed.

Demolition of reinforced cement concrete as in drains or manhole covers of any description and in any position not otherwise specifically provided for complete all as specified and as directed

S&F Factory made precast heavy duty drain/manhole cover with MS frame and reinforcement as per IS 12592 : 2002 with specified thickness (size Square/rectangular/circular with ring) complete all as specified and as directed.

S&F Stainless steel ( Grade 304) hollow tube min thickness 16 guage (Round or square/rectangular pipe) of any dia /size fixed as in posts / railing with knock-down fixing system & top Mounted Round Baluster made of 38 to 50mm dia Stainless steel 304 Grade ,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement including taking down old pipe and make good the surfaces as required complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm in soft/loose soil complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed.

M&L for aluminium alloy powder coated (50 micron ) anodized frame of section 85 mm x44 mm x2 mm thick as in aluminium partition including aluminium anodized snap beading and rubber packing ,partly glazed with 5 mm thick tinted glass and partly with 12 mm thick prelaminated particle board both sides laminated including taking/dismantling old partion wall complete all as specified and directed .

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repair aluminum alloy door closer hydraulically regulated, desination No 2 universal type, suitable for door shutters of 701 to 850mm in width and weight between 36 to 60 Kg and fixed to door frame complete all as specified and directed.

S&F aluminium anodised grill 6x4.5mm thick section 10cm centre to centre spacing complete with U channel all round fixed in window with screws including taking down old grill complete all as specified and as directed

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 18 to 20mm thick granite stone slab as in floor or shelves, over cooking platform,machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, moulding and polishing and beveling half round edges of stones laid over & inculding 15 mm thick sereed bed in CM (1:6) complete all as specified and directed.

M&L for 18 to 20mm thick granite stone slab on vertical surfaces such as skirting/dado etc set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone and beveling half round edges of stones fixed over and incl rendering 10 mm thick in CM (1:3 ) complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20 mm thick over & including 15 mm cement screed base laid in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polishing complete all as specified and directed

M&L for Machine cut Kota stone slab 18--20mm thick in riser or steps, skirting, dado and pillar laid over & including 10mm thick rendering in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite polishing complete all as specified and directed

Dismantling tiles in floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable material to store and rubbish of the premises complete all as specified and as directed.

M&L for ceramic coloured tiles 450 x 300 x 7 mm thick in dado/skirting on wall etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick cement plaster in CM (1:4) all as specified and as directed.

S&F in repair Vertical Veniation blind consisting of aluminium head rail, vanes/louvers 4” wide of approved tint and traverse cord complete all as specified and as directed.

S&F in repair rolling vertical veniation blind consisting of aluminium head rail, of approved tint and traverse cord complete all as specified and as directed.

S&F in repair 12 mm thick toughened frosted glass with one door fixed and one openable , comprising of height 2100 mm and width 1000 to 1200 mm ( as required at site) with pivot door of appropriate width including stainless steel chrome finish hardware fitting and all fittings and fixture as per manufacturer's instructions complete all as specified and ditrected.

S & F toughened frosted glass 12mm thick fixed on wall with cleats on wooden /Aluminium frame including fixing acessories complete all as specified and directed.

Material and labour for demolition of wall and ceiling board (Fibre,pulp,insulation etc.) or insulation board / slab / blankets any thickness including cover fillet / grids etc complete all as specified and directed.

M&L for Gypsum board 12 mm thick for seamless POP false ceiling to flat surface fixed with screw over and including Gl frame work comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including finishing the joint of face board with specially formulated jointing compound & 48 mm wide fibre tape to provide seam less finish complete as per manufacturer instruction complete all as specified and directed

Supply and fixing for Gypsum Board 12 mm thick cornices of upto 450 mm wide along the false ceiling on vertical surfaces fixed with cadmium plated screw, design as approved complete all as specified and directed.

M&L for durable, coating, Corrosion Resistant, tamper proof, water proof seamless POP false ceiling including all accessories required for POP false ceiling as per manufacturer instruction including two coat of approved coloured painting over one coat of primer complete all as specified and as directed.

M&L for POP false ceiling cornices of as design approved by user along the POP false ceiling on vertical surfaces fixed with cadmium plated screw, design as approved complete all as specified and as directed.

M&L for GI powder coated micro perforated micro metalic look false ceiling with fleece layer in type 0.5 mm thick, including provison of GI powder coated grid moudle of 600mm x 600mm size complete with GI powder coated grid consiting main runner suspended at 1200 mm centre to centre and cross runner T section suspended of 600mm centre to centrre supported by 4mm GI rod from ceiling surface including steel fastner and GI powder coated wall Note :-The sample of gird material and ceiling tiles alongwith fixing plan shall be got approved rom the GE(I) R&D before procurement of the Material.

M&L for painting hinting lines on roads n exc 15cm wide with hot applied thermoplastic compound paint confirm to MOST specified painting as per manufacturers direction specification, mechanically applied to form 1.5mm thick film on road lined including removing, cleaning and drying the existing road painting on surface with dust, oil, grease and moisture free surface before applying the paint complete all as specified and as directed.

S&F in repair fancy type stop valve/Angle valve with wall flange , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore etc complete all as specified and directed

S&F in repair 15mm bore brass chromium plated single lever basin mixture without pop up waste system with 450 mm long braided hoses complete all as specified and directed

S&F in repair Bib Tap fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe of 15 mm bore complete all as specified and directed

S&F in repair for 15mm bore brass chromium plated fancy type self closing censor pillar tap with capstan head screwed down high pressure with or without lettred hot or cold with long screw shank & fly nuts complete all as specified and directed

S&F in repair for brass chromium plated fancy type towel rail 600 mm long with both side brackets complete all as specified and directed.

S&F in repair PVC connection 45/60 cm long with brass check nuts on both sides suitable for 15 mm bore iron pipe complete all as specified and directed.

S&F in repair Stainless steel 125mm dia Grating Square /Round as required with or with out hole complete all as specified and directed.

S&F in repair chromium plated soap dish fixed to wall with CP brass screws complete all as specified and directed.

S&F in repair Stainless steel (AISI 304 grade) Satin finish automatic hand dryer complete all as specified and directed.

S&F looking mirror 5.50 mm thick of superior quality, any size, with approved border design fixed with commercial plywood 6 mm thick or AC board and with teak frame fixed in repair complete all as specified and directed .

S&F in repair Corner self 12" made out of 5 to 7 mm thick superior quality glass with CP brackets and railing fixed etc complete all as specified and directed.

S&F brass chromium plated bottle trap (with internal partition) 32mm size with 300 mm & 190mm long wall connecting pipes & wall flange complete all as specified and ditrected.

S&F in repair Push Button Soap Dispensers with ABS body of capacity 0.80 ltr complete all as specified and directed.

S&F in repair brass chromium plated health fauset,teliphonic type,with CP flexible arms and Jet,of approved make, suitable to fixed to 15mm bore CP angle valves complete all as specified and directed .

Supply and fixing in repair toilet paper holder brass Chromium Plated as approved complete all as specified and directed .

Supply and fixed in repairs PVC waste pipe for WHB/Urinal/Sink of any flexible length with union complete all as specified and directed .

S & F 500 ltr 3-layer heavy duty blow moulded polyethylene water storage tanks tripple layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PVC float valve including dismantling old Water tank complete all as specified in SSR Pt-I and all as specified and directed.

S & F 1000 ltr 3-layer heavy duty blow moulded polyethylene water storage tank, tripple layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PVC float valve including dismantling old Water tank complete all as specified in SSR Pt-I and all as specified and directed.

Taking up or down 15 mm bore steel tubing & connection including cleaning for refixing serviceable tubing complete all as specified and directed.

Taking up or down 20 mm bore steel tubing & connection including cleaning for refixing serviceable tubing complete all as specified and directed.

Supply and fixed steel water tubing 15 mm bore, medium grade , galvanised with all fittings and fixed complete to walls and ceiling or laid in floors including cutting in wall /floor for pipe complete all as specified and directed.

Supply and fixed steel water tubing 20 mm bore, medium grade , galvanised with all fittings and fixed complete to walls and ceiling or laid in floors including cutting in wall /floor for pipe complete all as specified and directed.

Supply and fix 32 mm dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and a n t i m i c r o b i a l welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc complete all as specified. Note:- Cutting chases for concealing the pipes & fittings etc wherever required and making good, disturbed surface in Cement mortar 1:3 complete shall be included in the quoted rate.

All as per item No 99.00 above but 20 mm dia.

Supply & fixing in repairs vitreous china wash down water closet pedstal pattern white excluding fixing bolts, flushing cistern and flush pipe complete but including PVC seat cover with aluminium hinging devices & EWC CP Jet chromium plated with 1.00 mtr long PVC connection pipe complete all as specified and directed.

Supply and fixing WC Orissa pattern size 580 x 440 mm of vitreous china (white) fixed with all included accessories including integral footrest including taking down old WCs etc complete all as specified and directed.

Supply and fixing in repair PVC low level flushing cistern 10 ltr capacity sleek having weight not less than 1.80 KG including PVC bend, supporting brackets and complete accessories white colour as in repair complete all as specified and directed.

Supply and fixed in repair urinal, Half stall type,white with grating, union for discharge pipe, flush pipe and waste pipe, CP urinal Spreader fixed to water supply pipe complete all as specified and directed.

Supply and fixed in repair 10.00 thick glass urinal partition of size 310x700 mm or 450 x900mm complete all as specified and directed.

Dismantling of floor tiles / hearth of wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish of the premises etc complete all as specified and directed.

M&L for 1st quality non-skid coloured ceremic tiles 7 to 8 mm thick, in light shade, (Square/rectangular) joint less / joint free, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed

M&L for vitrified ceremic tiles 8 to 9 mm thick, in light shade, double charge (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed

M&L for 1st quality glazed ceramic designer coloured tiles of size 450x300x7-8 mm thick on vertical surface as in skirting/dado set and jointed in neat cement slurry and pointing to in white or coloured cement to match the surface over & inculding 10mm thick rendering in CM (1:4) on brick wall complete all as specified and directed.

M&L for 1st quality glazed ceramic designer coloured tiles of size 600x300x7-8 mm thick on vertical surface as in skirting/dado set and jointed in neat cement slurry and pointing to in white or coloured cement to match the surface over & inculding 10mm thick rendenring in CM (1:4) on brick wall complete all as specified and directed.

Demolition of wall and ceiling board with frame work of ceiling (Fibre,pulp,insulation etc.) or insulation board /slab/blankets any thickness including cover fillet etc complete all as specified and directed.

S&F roof ceiling with minimum 0.5 mm thick micro metalic ceiling tiles size of 600x600mm with including provison of GI powder coated grid moudle of 600mm x 600mm size complete with GI powder coated grid consiting main runner suspended at 1200 mm centre to centre and cross runner T section suspended of 600mm centre to centrre suupported by 4mm GI rod from ceiling surface including steel fastner and GI powder coated wall complete all as specified & directed. Note:-The sample of gird material and ceiling tiles alongwith fixing plan shall be got approved from the GE(I) R&D Delhi before procurement of the Material.

S&F powder coated Gl frame work for roof ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers rod of 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including 9 to 10 mm thick gypsum ceiling tile/board of size 600 x 600mm decorative type with silver foil coating on back side of ceiling board for insulation and accoustic purpose, fixed with staple with on snap grid and 4mm dia GI wire with nuts, bolts , adjustable arrangement & washers etc complete all as specified and directed. Note:-The sample of gird material and ceiling tiles alongwith fixing plan shall be got approved from the GE(I) R&D before procurement of the Material.

Cutting openings, through brick walls built in cement mortar, for door, windows and other openings or enlarging existing openings, converting window into door openings, etc. including providing, fixing and removing shoring, cleaning stacking bricks, removing surplus serviceable bricks,hard core, etc. to store and rubbish off the premises not exc.50 mtr. complete all as specified and directed .

Taking down chowkhats or frames n.exc 1.5 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc complete all as specified and directed.

Taking down chowkaths or frames Exc 1.5 sqm but n.exc 4 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc complete all as specified and directed.

Taking down shutters of any description exc 1 sqm but n.exc 2.00 Sqm each complete all as specified and directed.

Supply and fixed 2nd class hard wood plain, solid, straight, chowkhat and frames, wrought, framed rebated on the solid, rounded or chamfered,put together with glue pinned at joints. Complete all as specified and directed

S&F 40 mm thick flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specified & directed.

Material and labour for Melamine polishing on wooden surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and directed .

Supply and fixed 100 mm size cast brass with mild steel hinge pin bright polished and fixed, type B-11 fixed/ welded to frame complete all as specified & directed.

Supply and fixed 200 mm long,brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts complete all as specified & directed.

Supply and fixed 300mm long brass, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fixed brass handles cast type 150mm size complete all as specified and directed.

Supply and fixed 150mm long floor door stopper of brass body and anodised , with hard drawn steel spring. fixed in floor,complete all as specified & directed.

M&L for aluminum alloy powder coated (50 micron) anodized door frame of section 100 mm x 44 mm x 2mm thick, door shutter of aluminum section of size 85 mm x 44 mm x 2 mm thick, top rail and both styles of size 100mm x 44 mm x 2mm thick, lock rail and bottom rail of size 115 mm x 44 mm x 2 mm thick including aluminum anodized snap beading and rubber packing & 5.0 mm thick colour designer glass including, 200 mm long tower bolt-2 Nos, 200 mm long aluminium handle- 02 Nos on each leaf, 4 lever lock brass 100 mm long mortice lock, & double action floor door spring heavy duty suitable for 1 m wide shutter for each leaf complete all as specified and directed.

S&F powder coated aluminium window shutters of aluminium section of size for all member size 47.50x44.40x1.60mm thick with chowkat made out of hollow aluminium section size 63.5x38.10x1.60mm thick suitable for aluminium shutter and aluminium guard bar each shutters having two Nos aluminium hinges 100mm long, 100mm size aluminium handle and two nos 150mm long aluminium tower bolt and glazing with 4.8 mm thick sheet glass ordinary quality in square exceeding 0.5 sqm each pane coloured and fixed with glazing clips/ pins rubber beading and aluminium beading complete all as specified and directed.

M&L aluminium alloy powder coated (50 micron ) anodized frame of section 85 mm x44 mm x2 mm thick as in aluminium partition including aluminium anodized snap beading and rubber packing ,partly glazed with 5 mm thick tinted glass and partly paneled with 12 mm thick prelaminated particle board complete all as specified and directed .

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed etc complete all as specified and directed.

Hacking out old broken glass (any thickness) size quality or description from wooden/steel frame etc complete all as specified and directed

S&F in repair 5.00mm thick tinted glass with glazing clips rubber beading and aluminium beading for aluminium door /window area exc 0.5 sqm complete all as specified & directed.

S&F in repair 5.00mm thick reflector sole sheet glass with glazing clips rubber beading and aluminium beading for aluminium door /window area exc 0.5 Sqm complete all as specified and directed.

S&F in repair 12mm thick prelaminated particle board with glazing clips rubber beading /gasket and aluminium beading for aluminium door complete all as specified and directed

S&F in repair any size brass mortice lock six levers with duplicate key for aluminium door , complete all as specified and directed.

M&L for wooden flooring of 8mm thick size 1216x192mm with interlocking pannels with plastic and silicate mixture as the core material and surface with wooden foil on the top with thickness of 10mm width of 200mm and length of 2.74/3.05 (9'x10') meters , small embossed surface with flossy finish as per manufacturer instruction including taking down old wooden flooring complete all as specified and directed :

S&F L/H/U profile and corner profile molding with fillet at top ,bottom and corner to hold the wooden flooring and wall panelling with exactly the same shade as that of the flooring planks as per manufracturer instruction complete all as specified and directed.

S&F wall panneling of wooden WPC as per approved sample 8mm thick size 1216x192mm with interlocking pannels with plastic and silicate mixture as the core material and surface with PVC foil on the top with thickness of 10mm width of 200mm and lengt of 2.74/3.05 (9'x10') meters , small embossed surface with flossy finish including taking down old wooden flooring complete all as specified and directed :

S&F in repair 10 mm thick toughened frosted glass door with side & Tops glass fixed with openable door , comprising of height 2100 mm and width 1000 to 1200 mm ( as required at site) with pivot door of appropriate width including stainless steel chrome finish hardware fitting , floor machine and all fittings as required including and fixture as per manufacturer's instructions complete all as specified and ditrected.

Supply and fixed Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick wood grain printed PVC sheet reinforced with M.S. Square tube, suppling and fixing in opening as per specification & drawing etc complete all as specified and directed.

Material and labour Factory made solid panel PVC wood grain printed door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side &as gap insert for top rail & bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to gathers with solvent cement supplying & fixing the frame at site complete all as specified and directed

Supply & fixing mild steel butt hinges 100 mm long medium weight complete all as specified and directed.

Supply & fixing aluminium anodised extruded fabricated type handle 150mm long complete all as specified and directed.

Supply & fixing Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 250 mm long and fixing with bolts extruded sections complete all as specified and directed.

Supply and fixing 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Taking down of Aluminium door/window shutter of any description area of each shutter not exceeding 1.5 sqm and refixing in same opening after carry out necessary repair including oiling, tightening the joints/bolts , fixed to floor spring / hinges, rubber beading, aluminum beading, handles, sliding bolts, hinges, tower bolts complete all as specified and directed NOTE: i) Floor spring to be paid under relevent Item of this schedule. ii) Rate for all T&P required for repair incl fixing of rubber packings, screws etc complete to make good the shutter are deemed to be included in quoted rates all as directed.

All as per item No 145.00 above but area exceeding 1.5 sqm and n exc 4.00 sqm.

Supply and fixing in repair double legged door stopper of aluminium alloy with rubber base, 150mm long complete all as specified and directed.

S&F for Collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets including taking down old collapsible door ,complete all as specified and directed

S&F powder coated anodised aluminium frame / shutter frame for door, window,ventilators with one or more rebates including joining cleats for fixing complete all as specified and directed.

S & F in repair sound proofing tempered ordinary quality glass of 5.50 mm thick fixed on Aluminium frame in double layered at on place with 5mm gap to absorb sound including fixing all acessories etc complete all as specified.

S&F in repair MS wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples or incl wooden beading & necessary welding to steel windows complete all as specified.

S&F in repairs sheet glass 3 mm thick ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane including hacking out old broken glass any thick-ness complete all as specified.

M&L for 19/20mm thick prelaminated particle board interior grade prelaminated on both sides with decorative choice lamination fixed with screws to timber framed work including dismantling of old unserviceable boarding any description complete all as specified.

S&F in repair continuous (Piano) hinges, mild steel bright finish or electro galvanised (width of flap when open 30 mm) complete all as specified and directed.

S&F in repair 30 mm dia, cupboard knobs fancy type fixed with nut screw and washer of mild steel, bright finished complete all as specified and as directed.

Supply only integral water proofing compound (ISI marked) complete all as specified and directed.

Material and labour for draining out water, cleaning by removing silt/sludge, all scales, dust from RCC/AC/PVC water storage tank exceeding 500 litres and not exceeding 2000 litres capacity from mouth of circulating pipes and writing letters of height not less than 10 cm with white synthetic enamel paint such as date, month & year of cleaning including removing old waste/dust complete all as specified and as directed

M&L for taking out old bitumen joints of any type from roof surfaces and filling the same with new bitumen grade B including two coat of bitumen primer to exiting surface before filling the joints and after filling the joints applying two coat of aluminum silver paint as per manufacture instruction complete all as specified and directed.

Sree Ram Enterprises