Construction of CHC building at Janjehli Tehsil Thunag Distt Mandi HP SH Construction of 2nd floor and 3rd floor WS and SI Septic Tank and Rain Water Harvesting System

Amount

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth upto any leads and lifts disposted earth to be leveled and neatly dressed as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Providing form work with steel plates 3.15mm. (Three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5mm. (Thirty x thirty x five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to all floor level and removal of same for insitu reinforced concrete and plain concrete work as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . a) Columns, pillars, posts and struts in square, rectangular or polygonal in plan.

b) Flat surfaces such as soffits of suspended floors, roofs ,landings and the like, floor etc. upto any thickness.

c) Beams, cantilevers, girders and lintels, sides and soffits of beams, beam hunching, cantilevers, bressumers and lintels upto any depth in all heights from any floor level.

d) Stair cases with slopping or steped soffits excluding landing.

e) Vertical surfaces such as walls(any thickness) , partitions and the like including attached pillasters ,buttresses, plinth and string courses and the like.

f) Edges of slabs and breaks in floors and walls in any width.

Providing and laying cement concrete mechanically mixed and vibrated 1:5:10 ( one cement : five sand : ten graded stone aggregate 40mm.(Forty millimetre) mechanically mixed and curing complete excluding the cost of form work in foundation and plinth as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Stone filling under floor including carriage of material within all leads and lifts and other incidentals.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Stone soling/boulder filling dry hand packed in under floor as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying design mix M-20 (twenty) grade cement concrete work mechanically mixed and vibrated with minimum cement concrete of 320 kg (three hundred twenty kilogram) per cubic metre with graded crushed stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . i)Suspended floors , roofs, landings and shelves and their support , balconies, beams, girders,bressumers and cantilever upto floor any level.

ii)Walls (any thickness but not less than 0.10 m (Zero point one zero) metre thickness) including attached pilasters , buttersses,plinth and string courses etc. from top of foundation upto all floor level

Providing and laying cement concrete design mix M-25(twenty five) grade of cement concrete work mechanically mixed and vibrated with minimum cement content of 320 kg/cum with graded/crushed stone aggregate 20mm. (Twenty millimetre ) nominal size) complete excluding cost of form work and reinforcement for reinforced concrete work upto all floor level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . a) Suspended floors , roofs, landing and shelves and their supports, balconies, beams , girders, bressumers and cantilever upto floor any level.

b) Columns, pillars, posts and struts square rectangular polygonal in plain upto all floor level.

c) Stair cases (except spiral stair case) excluding landing but including preparing of the top surface and finishing of nosing upto all floor level.

Providing and laying up to all floor level reinforced cement concrete 1:2:4 (one cement : two Sand :four graded stone aggregate 20mm nominal size) mechanically mixed and vibrated to give an smooth and even surface including centring and shuttering etc upto all level but excluding cost of reinforcement in String courses, copings, bed plates, anchor blocks, plain windows sills and the like as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position including cost of binding wire complete upto floor all level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Brick work using common burnt clay building bricks in foundation and plinth in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Brick work using common burnt clay building bricks in super structure above plinth level in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Half brick masonry in common burnt clay building bricks in cement mortar 1:3 (one Cement :Three Sand) (2nd Class Brick)in super structure above plinth level upto all floor level as per the direction of Engineer-in-chargeincluding carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 12mm thick Glass Reinforced concrete cladding of approved shape and texture of unistone or its equivalent made from portland cement alkally resistance glass fibres, UV resistant synthetic inoraganic pigment combined with the range of chemical additives on exterior surface side as on faces of Arch masonry walls etc. 12mm. (twelve millimetre)thick cement plaster 1:3(1cement:3sand) and jointed with cement slurry including scaffolding etc complete in all respect as per specification and the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing, supplying & fixing of glazing Open able Door made out of multi chambered PVC sections with TPV gasket having isolated drainage and reinforced with Galvanised Iron profiles throughout the window. The outer frame having overall size of 60 x55 mm with reinforcement of 1 mm thickness, sash with overall size of 102 x 60 mm with reinforcement of 1.5 mm thickness. Glazing bead for fixing of glass shall be of size 34 x 20 mm and coextruded with gasket. Composition of profile shall consists a minimum of 6 PHR of CaCo3 for every 100 parts of PVC resin. Doors shall be provided with 6 mm plain float glass, standard hardware, multi point locking system and 3D hinges wall thickness of frame, mullion & sash shall be 2.2 to 2.4 mm complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals

Providing, supplying & fixing of glazed 3 Track -2 Panel Sliding door with Mesh(I 75) made out of multi multi chambered PVC sections with TPV gasket having isolated drainage and reinforced with Galvanised Iron 120 GSM profiles throughout the window. The sliding cuter frame having overall size of 50 x 82 mm(fifty x eighty two millimetre) with reinforcement of 2 mm(two millimetre) thickness, sash with overall size of 50 x 82 mm with reinforcement of 1.5 mm (one point five millimetre) thickness. Glazing bead for fixing of glass shall be of size 20 x 18 mm (twenty x eighteen) and coextruded with gasket. Composition of profile shall consists a minimum of 12 PHR of CaCo3 for every 100 parts of PVC resin. Fiber glass mesh shall be provided in mesh shutter. Window/Door shall be provided with 6 mm( six millimetre) plain float glass, standard hardware, multi point locking system of patio espagnolette. wall thickness of frame & shash shall be 2.4 - 2.6mm complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing, supplying & fixing Top hung Ventilator with exhaust fan provision made out of multi chambered PVC sections with TPV gasket having isolated drainage and reinforced with Galvanised Iron 120 GSM profiles throughout the window. The outer frame having overall size of 60 x 55 mm(sixty x fifty five millimetre) with reinforcement of 1 mm thickness, mullion with overall size of 74 x 60 mm(seventy four x sixty millimetre) with reinforcement of 1 mm thickness and sash with overall size of 75 x 60 mm with reinforcement of 1.5 mm thickness. Glazing bead for fixing of glass shall be of size 34 x 20 mm (thirty four x twenty millimetre)and coextruded with gasket. Composition of profile shall consists a minimum of 6 PHR of TiO2 and not more than 12 PHR of CaCo3 for evry 100 parts of PVC resin. Ventilator shall be provided with 4.5 mm Pin Head glass, standard hardware, single point locking and friction stays. Wall thickness of frame, mullion & shash shall be 2.2- 2.4 mm complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing, supplying & fixing of Fixed Louvered Ventilator made out of multi chambered uPVC sections with TPV gasket having isolated drainage and reinforced with Galvanised Iron 120 GSM profiles throughout the window. The outer frame having overall size of 60 x 55 mm(sixty x fifty millimetre) with reinforcement of 1 mm(one millimetre) thickness, mullion with overall size of 74 x 60 mm (seventy four x sixty millimetre) with reinforcement of 1 mm thickness. Composition of profile consists a minimum of 6 PHR of TiO2 and not more than 12 PHR of CaCo3 for evry 100 parts of PVC resin. Ventilator shall be provided with 4.5 mm Pin Head glass, standard hardware. Wall thickness of frame, mullion & shash shall be 2.2- 2.4 mm complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing anodised aluminium work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws complete

P/F 12 mm thick bwp phenol bonded exterior/interior grade panalled shutters for frame of aluminium for doors including bright finished/black enamelled iron butt hinges with necessary screws 40 mm thick frame. complete as per specification and as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 35mm (thirty five millimeter)thick MDF flush shutter with hole of size 30cmx30cm fixed with6 mm glass and 1 mm thick lamination on both side of approved shade in merino laminates or green ply with edges of frames of first class deodar wood including bright finished black enameled iron butt hinges with necessary screws as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing grill of aluminium anodised powder coated pattern to existing window/ventilatior with 80mmx80mm panels holes with 25x8mm thick aluminium flat in windows and ventilators including fixing with aluminium screws or bolts and nuts complete in alluminium channels base frames (Aluminium channels base frames to be measured and paid for separately) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals ..

Providing and fixing aluminium sheet 4 mm (four millimetre)thick composite panel having core of polythene fixed to internal side with screws or nails as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing anodized aluminum tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . 200x10mm (Two hundred x ten millimeter)

150x10mm (One hundred fifty x ten millimeter)

100x10mm (One hundred x ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

75 mm (seventy five millimeter)

Providing and fixing bright finished brass 100mm.(One hundred millimeter) Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing bright finished hard drawn hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 250mm (Two hundred fifty millimeter)

200mm(Two hundred millimeter)

Providing and fixing 115mm (one hundred fifteen millimeters) bright finished brass heaps and stepples (safety type) with necessary screws etc complete as per directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 150mm (one hundred fifty millimeter) oxidized M.S. single acting spring hinges with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing double action hydraulic floor spring of approved brand and manufacture (conforming to IS 6315) for aluminium door including cost of cutting floor as required embedding in floors and cover plates etc. complete as per the direction of Engineer-In-Charge I/c carriage of materials with in all leads lifts and other incidentals.

Providing and fixing 19mm thick (ninteen milimetre) thick terramite resistant water proof commercial board box including shelves and shutters, the back side of cupboard/cabinet of 8mm(Eight milimetre) thick ply and cut portions of shelves shall be finished with 6mm six milimetres) hard board edging. The cut portion of shutters from all the sides shall be finished with 12 mm thick hard wood edging. the shutters from out side shall be finished with 1mm thick laminated of approved shade including piano hinges and magnetic catcher with all ascessories as per detail architectural drawing and specification complete in all respect as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 40mm (fourty milimetre)Cement concrete flooring 1:2:4(one cement two sand four draded stone aggregate 20mm (twenty milimetre)nominal size laid in one layer finished floating coat of neat cement upto any floor level as per direction fEngineer-in-Charge carriage of materials with in all leads, and other incidentals.

Providing and laying 10mm thick full body vetrified tiles of Asian/Johnson/Kajaria or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10mm (ten millimetre) thick full body vetrified tiles of Asian/Johnson/Kajaria or equivalant 600x600mmx10mm (six hundred into six hundred millimetre into ten millimetre) manufactured of approved shade and colour in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing wall paneling of 12 mm (twelve millimeter) thick pre laminated particle board (one side) of approved brand of soft wood 4x4 cm frames @60 cm center to center on both side fixing with rrawl on wooden pags screws and showing 8mm (Eight milimeter) wide and 12mm deep groves of required pattern in elevation and finished jeak wood beading on top 25x12mm(twenty five millimeter x twelve millimeter) /Cornish out to 75x60mm(seventy millimeter x sixty millimeter) of different pattern in top middle and corner joints including polishing and painting groves complete.as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10mm thick full body glazed anti skid water vetrified tiles with VC Shield Technology Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landing etc. of Somany/Kajaria/Nitco or its equivalentof approved shade and colour laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and full body vitrified tile 600 x 600 mm(six hundred millimetre x six hundred millimetre) with VC shield technology in Skirting 10mm (average)thickness base of cement 12mm (twelve millimetre) mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying Duro stone Antiskid Digital Ceramic tiles (300x300mmx10mm) of Somany/Kajaria/Nitco or its equivalentof approved shade and colour in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10mm thick 300x300mm Antiskid Matte finish tiles of Johnson/Asian Kajaria/Nitco or its equivalentof approved shade and colour in floors, treads laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 10mm thick of size 600 x 600 mm Antistatic vitrified tiles to provide antistatic conductive abrasion resist hard wearing and levelled floor in Asc Blue clour suitable for the specified use lay down the existing floor with proper application process. The antistatic conductive rectified vitrified file with all punched corners of make H&R Johnson India/Orient/RAK/Kajaria/Nitco should have surface electrical resistance conductive less than 1 megaohms with static decay time less than 0.5 Seconds and area ieach tile should be 0.36 Sqms in flooring laid over 12mm thick cement mortar1:3 (1 cement : 3 sand) jointedwith cement slurry mixed withpigment to match the shade of tiles as required complete.as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying Talai/Coble/Local stone flooring 50mm (fifty millimetre) (average) thickness of stone laid over 25mm (twenty five millimetre) thick cement mortar bed of 1:4(1cement: 4 sand) including pointing with cement mortar1:3 (1cement:3 sand) complete as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 15 mm (fifteen millimetre) thick full body glazed anti skid exterior grade vetrified tiles Asian/ Johnson/ Kajaria/ AGL or equivalant 600x600x15mm (six hundred into six hundred into fifteen millimetre) manufactured of approved shade and colour in skirting risers of steps and dados laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying granite stone in flooring 20 mm (twenty millimetre) (average) thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete as per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 8mm (eight millimetre) digital ceramic tile of size 300 x 600 mm (three hundred into six hundred millimetre) in skirting risers of steps and dados on 8mm (eight millimetre) thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Kota stone slab flooring 25 mm (twenty five millimetre) thick in risers of steps, skirting, dado and pillars etc. laid on 12mm thick (Twelve milimetre) thickness kota stone on 20 mm base of cement mortor 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing completeas per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying granite stone in flooring 20mm(average)thick rough finished granite stone (80% polished and 20 % unpolished) of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. 20mm.thick including rubbing and polishing complete within all leads, lifts and other incidentals. As per the directions of Engineer-in-Charge.

Providing and fixing prepainted sandwich puffed roofing with top skin of 0.6mm thick prepainted steel sheet over steel trusses made of cold rolled steel coil having a puff depth of 50mm rock wool and interior skin of 0.50mm prepainted steel sheet steel frames are to be painted of approved shade i/c fixing with prepainted iron J or L hooks, bolts and nuts with prepainted limpet and rubber washers complete with all accessories as required as per the especification and direction of Engineer-in-Charge i/c carriage of material within all leads, lifts and other incidentials.

Providing and fixing ridges or hips 60cm overall with prepainted sandwich puffed roofing with top skin of 0.60mm thick prepainted steel sheet over steel trusses made of cold rolled steel coil having a puff depth of 50mm rock wool and interior skin of 0.50mm prepainted steel sheet steel frames are to be painted of approved shade i/c fixing with prepainted iron J or L hooks, bolts and nuts with prepainted limpet and rubber washers complete with all accesoriees as required as per the specification and direction of Engineer-in-Charge i/c carriage of material within all leads, lifts and other incidentials.

Providing and fixing valley 60cm overall with prepainted dsandwich puffred roofing with top skin of 0.60 mm thick prepainted steel sheet over steel trusses made of cold rolled steel coil having a puff depth of 50mm rock wool and interior skin of 0.50mm prepainted steel sheet steel frames are to be painted of approved shade i/c fixing with prepainted iron J or L hooks, bolts and nuts with prepainted limpet and rubber washers complete with all accesoriees as required as per the specification and direction of Engineer-in-Charge i/c carriage of material within all leads lifts and other incidentials.

Providing and fixing flushing 38cm(Thirty centimeter) overall with 0.60mm ( Zero point six milimetre)thick prepainted sheet in roofing with hot dipped metallic Zink coated sheet with top coat of regular modified polyester organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with screws pre painted J or L hooks, bolts and nuts 6mm(Six milimetre) dia meter & pre painted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-In- charge i/c carriage of material within all leads lifts and other incidentials.

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg/sqm(Four point five kilogram per square metre) including filing the joint with approved adhersive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete as per the direction of Engineer-in-Charge i/c carriage of materials within all leads, lifts and other incidentals. PVC Plain Bend 100mm(One hundred milimetre) dia.

Shoe 100mm dia(One hundred milimetre) dia.

Providing and fixing 15 cm (fifteen centimetre) wide 45 cm (forty ive centimetre) overall semicircular plain G.I.sheet Gutter with iron brackets 40x3mm(forty five milimetre) size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per the design and direction of Engineer-in-Charge including carriage of materials with in leads,lifts and other incidentals.

Providing and fixing M.S. BP Sheet 1.66 mm(One point sixty six milimetre) to 2mm (Two milimetre) thick in eves board/ facia/soffit/ceiling including cutting ,fixing and welding to steel roof members and applying a coat of red lead primer complete as per direction of the Engineer-in-Charge (Base members of steel work shall be paid & measured separtely) including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work,including cutting, hoisting fixing in position and applying a priming coat of red lead paint in:Trusses and trussed purlins in buildings including carriage of materials with in all leads,lifts and other incidentals.

Providing and fixing 62.5mm x 75mm (sixty two point five millimetre into seventy five millimetre) hand rails in 1st class Indian teak wood straight length complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

Providing and fixing 50mm(fifty millimetre) dia balusters 1st class indian teak wood fixed with ends housed (square or splay) to hand rails and treads or strings complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm (twenty into ten into two milimetre) braced with flat iron diagonals 20x5mm (twenty ito five milimetre) size with top and bottom rails of T iron 40x40x6mm (forty into forty into six milimetre) with 38mm(thirty eight milimetre) dia steel pully complete with bolts and nuts locking arrangements, stoppers, handles, including applying a priming coat of red lead paint as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering (Two coats) with oil bound washable distemper of approved brand and manufacture of and of required shade of undecorated wall surface to give an even shade over and including a priming coat with alkali resistance primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surfaces to give an even shade i/c thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth i/c applying of putty a required for making the surface as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease,dirt and other forein matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/Asian Shalimar) conforming to IS: 3536-1966 brushing as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give an even shade including cleaning of oil, grease,dirt and and other foreign matter sand papering and stoping ready mixed paint other than white as per direction od Engineer-in-including carriage of materials within all leads, lifts and other incidentals.

Finishing Wall with weather proof exterior grade emulsion of approved brand (Apexultima) or its equrlied on undecorated wall surfaces (two coat) to give an even shade and final finish after cleaning complete thoroughly the surface fto remove all dirt, dust and other foreign matter and sand papered smooth as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrubers and sand paper complete with ready mixed priming pant brushing red leadred oxide/zinc oxide chrome as per the direction of Engineer-in-Charge including of materials within all leads,lifts and other incidentals.

Painting two coats (excluding priming coat) on new steel and other metal surfces surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters Enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals.

Polishing two coats with french polish on new wood based surfaces to give an even surface including cleaning the surface of all dirt,dust,and sand papered smooth and including a coat of wood filler as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing plinth protection 50mm (Fifty millimetre) thick in cement concrete 1:3:6 (one Cement : three sand : six Graded stone aggregated 20mm (Twenty millimetre) nominal size) mechanically mix finishing surface of concrete smooth as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing under layer for plinth protection of 75mm (Seventy Five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (Forty millimetre) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Constructing course rubble hammer dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two centimetre) in cement mortor 1:6 (one cement: six sand) and in side pllastering with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4 (one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Everest designer cement board ceiling tiles of size 600 x 600 mm (six hundred into six hundred millimetre) over readymade powder coated metal sheet section frame work 600 mm (six hundred millimetre) center to center grid suspended from ceiling of approved quality with butt jointing and nails complete specification and as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Supplying cast iron cover with frame for manhole for frame of internal dimension 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) rectangular CI cover the weight of cover to be not less than 38 kg (thirty eight kilogram) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floors as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 20mm (Twenty Millimetre) nominal bore

25 mm (Twenty Five Millimetre) nominal bore

Providing and fixing to wall and ceiling and floor Polythene Aluminium composite pressure pipe of 15mm dia of Kitec confirming to ISI 15450-2004 including making good the wall, ceiling and floor as per specification and the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying in trenches, galvanized mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. . 25 mm (Twenty Five Millimetre) nominal bore

Making connection of galvanized steel distribution branch with galvanized mild steel main 20mm(Twenty Millimetre) to 40mm (Forty Millimetre) nominal size bore by providing and fixing tee including cutting and threading the pipes complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Construction chamber 300mm x 300mmx500mm (Three Hundred x Three Hundred x Five Hundred millimetre) inside size for stop cock with C.I. surface box 100mm x 100 mm x 75mm (One Hundred x One hundred x Seventy Five millimetre) (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (one cement : two sand :four graded stone aggregate 20mm (Twenty millimetre) nominal size) 75mm (Seventy Five millimetre) thick foundation concrete 1:5:10 ( one cement : five sand : ten grades stone aggregate 40 mm (Forty millimetre) nominal size) and inside plastering with cement mortar 1:3 (one cement :three sand) finished with a floating coat of neat cement including curing complete with 100 mm (Hundred millimetre) thick walls of brick masonry in cement mortar 1:5 (one cement: five sand) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and. fixing Anglo Indian Universal WC No. 2061 with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) of Cera/Hindware/jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous China wash down, water closet European type. W.C. pan No 2011 crane WC 740x50x835 (Seven hundred into fifty into eight hundred thirty five) in white shade with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) of Cera/Hindware/jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing white plastic seat and cover for wash down water closet with C.P. Brass hinges and rubber buffers of Cera/Hindware/jaguar complete as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China wash down, water closet Orissa Pattern No.20004 squatting pan (Indian type W.C pan) size 580mm x 440 mm (five hundred eighty millimetre into four hundred forty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) of Cera/Parryware/Hindware/Jaguar as per the direction of Engineer in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT White colour high density polyethylene / poly propylene 10 litres capacity ( full flush) European standard control low level flushing cistern No. 2602 of Cera/Parryware/Hindware/Jaguar with fittings with a pair of brackets with fittings such a lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) .as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm (one hundred ten millimetre) dia PVC ‘P’ or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT jet spray of Cera/Hindware/jaguar with 1.5 mtr. ( one point five meters) Tube complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing of a pair of vitreous China 250mm x 130mmx30mm (two hundred fifty millimetre into one hundred thirty millimetre into thirty millimetre) foot rests for long pattern squatting pan water closet of Cera/Hindware/jaguar in cement mortar 1:3 (1 cement:3 sand), complete.as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing white glazed fireclay stall urinal with automatic flushing cistern of Cera/Hindware/jaguar with fittings R.S. or C.I. Brackets standard size C.P. brass flush pipe spreaders with unions and clamps (all in C.P. brass) C.I. Trap with outlet grating and other coupling in C.P. brass including painting of cistern and fittings, cutting and making good the walls and floors where required single stall urinal with 5 ltr. (five litre) automatic flushing cistern as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clamps etc. (all in C.P. Brass) including cutting holes and making good the same 32mm (thirty two millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing charlotte 1075 wash basin of size 650 x 570 mm with 1175 half pedestal of Cera/Hindware/jaguar with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing vitreous china wash basin Cornet No 1075 of flatback size 550 x 400 mm (five hundred fifty into four hundred millimetre) of Cera/Hindware/jaguar with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings flat back as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing stainless steel kitchen sink of size 610x460x200mm (six hundred ten into four hundred sixty into two hundred millimetre) No. 1022 of Paryag Polymers or its equivalent of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same (but excluding fitting) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 32 mm (thirty two millimetre ) dia diametre C.P brass waste for wash basin or sink of approved brand and menufature as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing M.I. Union for wash basin or sink 32mm (thirty two millimetre ) dia size including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 32 mm (thirty two millimetre ) dia C.P. Bottle Trap for wash basin or sink as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 600mm x 450 mm ( six hundred x four hundred fifty millimetre) beveled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing C.P. Brass Towel rail No 1581 of Jaguar complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws 600mm x 20mm (six hundred x twenty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 600mm x 120 mm (six hundred x one hundred twenty millimetre) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing toilet paper holder No 1533 of Jaguar/ESS-Ess or its equivalent in C P Brass as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing soap trays (Vitreous China ) Recessed soap tray with hand rail 300 mm x 160 mm (three hundred millimetre into one hundred sixty millimetre) size as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Division Plate for Urinals 600mm x 300.mm (six hundred x three hundred millimetre) Vitreous China as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing Shower head arm casted 19 mm long body round shape SHA -CHR-477 for wall mounted shower with flange of Jaguar complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass bib tap with Capstan head of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass pillar tap with Capstan head of Jaguar as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing 15 mm (Fifteen millimetre) dia C.P. Brass stop cock as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 15 mm dia PTMT concealed stop cock with flange of Jaguar and approved quality and colour as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing P.V.C. connection with Brass unions 300/450 mm (three hundred/four hundred fifty millimetre) length15 mm(fifteen millimetre) nominal size as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. .

Providing and fixing C.P. Brass waste, and plug for glazed ware sinks, basins, etc. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug, brass chain and studs 32mm (thirty millimetre) nominal boreas per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing brass full way valve with wheel as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. 15 mm (fifteen millimetre) nominal bore

20 mm (twenty millimetre) nominal bore

25 mm (Twenty Five Millimetre) nominal bore

Providing and fixing brass ball valve (horizontal plunger type) High pressure with polythene plastic floats 15 mm (fifteen millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing G.I./M.I Union of following sizes (where not included in the items) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals 15 mm (fifteen millimetre)

20 mm (twenty millimetre)

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level 1000 litres(one thousant litres) net capacity tank as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.110*90 mm (one hundred ten x ninty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes confirming to ISI -15328 SN8 of Supreme/Fenolex/Kitech marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals 110 mm dia (one hundred ten) dia

150 mm dia(one hundred fifty) dia

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete /including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC door bend with oval access door insertion rubber washer 3 mm Three millimetre) thick bolts and nuts ISI market complete including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC Collar ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 32 mm (thirty two millimetre) nominal bore PTMT waste coupling of approved quality and colour as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT Urinal waste coupling of approved quality and colour 40 mm (forty millimetre) nominal bore as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT grating round of approved quality and colour 100 mm (one hundred millimetre) nominal dia as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT urinal spreader of approved quality and color as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Grab Bar of Jaguar WAC-WHT-BR0600 692 mm satinless 40mm (forty millimetre) dia steel pipe at 78 m (seventy eight metre) height with MS plate as the position of seat as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying (to level or slopes) and jointing reinforced concrete light duty non pressure pipes I.S. Class N.P.2 or P of the following internal diameter with collars and butt ends prepared for collar joint including testing of joints complete. 150 mm (one hundred millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying Cement concrete 1:5:10 ( one Cement : five Sand : ten graded stone aggregate 40 mm (forty milimetre) nominal size) in hunching of S.W. pipes of the following internal diameters, Including concrete for beddings, necessary form work and curing complete.150 mm (one hundred millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 (one cement :five sand)and water tight C. I. cover with frame of 300mmx300mm( three hundred xthree hundred) size (inside) the weight of cover to be not less than 4.53kg (four point fifty three kilogram) and frame to be not less than 2.72kg.(two point seven two kilogram) square mouth trap 150*100 mm ( one hundred fifty x one hundred milimetre)size P or R type as per the direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals.

Constructing manhole with R.C.C. top slab in1:2:4 mix in ( one cement : two sand : four graded stone aggregate 20mm (twenty milimetre) nominal size) foundation concrete1:4:8 (one cement : four sand : eight )graded stone aggregate 40mm (forty milimetre)nominal size) inside plastering 15mm thick with cement mortar 1:3 (one cement three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (one cement : two sand : four graded stone aggregate 20mm nominal size) finished smooth complete including curring and testing Inside size 800 x 800x1000 mm deep (eight hundred into eight hundred into one thousand millimetre) deep including C.I. cover with frame (medium duty single seat pattern D) 455 x 610 mm (five hundred millimetre) internal diameters total weight of cover and frame to be not less then 38 Kg (thirty eight kilogram) (weight of cover 23 Kg (twenty three kilogram) Weight of frame 15 Kg (fifteen kilogram) with 300 mm (three hundred millimetre) thick walls of square rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three Sand) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Ajay Rathore