Providing LWSS to Kanda Kahanoo in GP Kanda and Manola Nirash in Tehsil Karsog Distt Mandi HP

Amount

Cutting in earth work in all classification of soil such as pick work, jumper work, blasting soft/ hard rock or chiselling soft/hard rock where blasting is prohibited and disposal of earth work with in all leads and lifts.

Excavation in foundation, trenches ( for pipes & pits/other civil works) upto all depths in all classification of earth work such as pick work, jumper work, saturated soil including bailing and pumping out water, blasting soft/ hard rock or chiselling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, leveling of beds to correct grade i/c shoring /strutting , planking, timbering & dewatering wherever required, stacking the useable & unuseable material /soil separately & after laying jointing & testing of pipes, returning the useable soil in trenches in 15 cm layers including consolidating of such deposited layer by ramming & watering & then disposing of all surplus excavated soil /unusable material as directed with in all leads & lifts including restoration of un-metalled /metalled surfaces to its original condition & including cost of diversion for traffic, night signals, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respects with in all leads & lifts as per directions of Engineer-in-Charge.

Providing and laying cement concrete 1:6:12( 1cement:6 sand: 12 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:4:8(1cement:4 sand:8 crushed stone agg. 40mm nominal size)and curing complete excluding cost of form work in foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:3:6 (1 cement: 3 sand : 6 graded stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring shuttering ,strutting and propping etc.with wooden battens and ballies,height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for in situ reinforced concrete and plain concrete work in:-

Flat surfaces such as soffits of suspended floors roofs landings and the like floors etc. up to 200 mm in thickness in all leads and lifts.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillaster,buttresses plinth and string courses and the like in all leads and lifts.

Providing form work of ordinary timber plankings so as to give a rough finish including centering,shuttering propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 meters and removal of the same for in-situ reinforced concrete and plain concrete work in :- arches up to 6 mtrs span, domes, vaults upto all span.

Providing and laying cement concrete 1:1.5:3(1cement:1.5 sand:3 graded stone agg.20mm nominal size )& curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:

Foundation and plinth in all leads and lifts.

Walls ( any thickness but not less than 0.1 m thickness) attached pillasters, buttresses, plinth and string courses, etc. from top of foundation level upto floor two level in all leads and lifts.

Providing and laying cement concrete 1:2:4 ( 1cement:2 sand: 4graded stone aggregate 20 mm nominal size )and curing complete excluding the cost of form work and reinforcement in:-

i) suspended floors, domes, roofs,landings and shelves and their supports, balconies, beams, girders, bressumers and cantilivers up to floor two level in all leads and lifts.

i) Vertical wall butt not less than 0.10m

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete up to floor two level in all leads and lifts.

Random rubble masonary/Polygonal rubble masonary (coursed or brought to courses with hard stones of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 in cement mortar 1:6 (1 cement : 6 sand) in all leads and lifts.

Stone filling behind R/wall in all leads and lifts.

Brick work using common burnt clay building bricks in foundation and plinth in cement mortor 1:6 (1 cement : 6 sand) 2nd Class in all leads and lifts.

Half bricks masonry in common burnt clay building bricks in cement mortar 1:4 (1 cement : 4 Sand). In all leads and lifts.

Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges, jump lock jamb, beed and if required angle threshold of mild steel angle of section 50X25 mm or base ties of 1.25 mm pressed mild steel welded or regidly fixed together by mechanical means, adjustable lugs with split and tails to each jamb including steel but things 2.5 mm thick with gaurds, lock strike plate and shock as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by Engineer-in-charge in all leads and lifts. Profile C

Providing and fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestorey windows,including black enamelled iron butt hinges with necessary screws. 45 mm thick. 2nd class deodar wood in all leads and lifts.

6mm cement plaster to ceiling in CM 1:3 ( 1Cement :3 Sand) in all leads and lifts.

15 mm cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering up to floor two levels including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 (1 cement:6 sand) in all leads and lifts .

Distempering with dry distemper of approved brand and manufacture (two coats) and of required shade on undecorated wall surfaces to give an even shade, sand papered smooth in all leads and lifts..

Applying priming coat on new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,greese,dirt and other foreign matters,sand papering and knotting.Ready mixed paint brushing wood primer pink in all leads and lifts.

Painting two coats (excluding priming coat) on new wood and wood based surfaces,with enamel paint to give an even shade including cleaning the surface of dirt ,dust and other foreign matters, sand papering and stopping with enamel paint other than white in all leads and lifts.

Providing and fixing oxidzed aluminuim sliding door bolts with nuts screws etc. Complete in all leads and lifts.

Providing and fixing oxidzed aluminium tower bolts ( barrel type) with screws etc. Complete in all leads and lifts.

Providing ad fixing oxidzed aluminium handles with necessary screws etc. Complete in all leads and lifts.

White glazed tiles 6mm thick in flooring, cement mortar 1:3(1cement:3 sand) finished with flush pointing in white cement in all leads and lifts.

White glazed tiles 6mm thick in skirting, risers of steps and dado 12mm thick cement mortar 1:3(1cement:3 sand)and jointed with cement slurry in all leads and lifts.

Providing and fixing of Steel/fibre reinforcement concrete (SFRC) manhole cover with frame conforming to IS-12592 (Part - I)-1998 with latest amendments 560 mm dia medium duty in all leads and lifts.

1.20 metre heigh fencing (as per approved design) 1.80 metres R.C.C.posts 3 metres centre to centre and R.C.C. struts with 7 horizental lines and two diagonals of galvanised steel bar bed wire (IS 278-1962 type I) weighing 9.38 kg./100 metres (minimum) strained and fixed to posts by typing to 6mm galvanised steel bar niles/clips with G.I. binding wire including cost of Excavation, R.C.C. Posts,R.C.C. struts and straining belts and embeded in cement concrete 1:4:8 ( 1cement : 4 sand : 8 graded stone aggregate 40 mm nominal size) and curing complete in all respect and to the entire satisfaction of the Engineer-in-Charge. with in all leads and lifts

Steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint in gratting, framed guard ber, ladders, railing brackets and similar works with in all leads and lifts.

Providing and fixing of MS Fabricated Protection Panel having size 750 mm x 750 mm made with MS Angle 40 x 40 x 4 mm for frame, MS Angle 30 x 30 x 3 mm for cover, MS Flat 25 x 5 mm for fixing of sliding door bolt and MS Sheet 3.15mm thick for protection of manhole covers of storage tanks including the cost of cutting and welding of MS angle, MS Flat & MS Sheet, embedding in RCC Slab by drilling holes in MS angle & in RCC slab, provision for providing and fixing sliding door bolt 300 x 16 mm, MS Handle 100 mm, Lock and applying a coat of red oxide paint and painting two coat with steel paint (Firoza Blue) complete job in all respect in all leads and lifts and to the entire satisfaction of the Engineer - in - Charge.

Laying,jointing and testing in trenches GMS tubes (light grade) tube fitting such as bends, tees, air valves,unions and collars etc. as per direction and to the entire satisfaction of the Engineer-In -Charge. (Earth work in trenches to be measured and paid for separately inlet or out let pipe

80 mm Diametre ( Light Class)

Providing anf fixing gun metal wheel valve with in all leads and lifts

80 mm dia .

Providing Providing and laying Cement Concerete 1:5:10 ( 1 cement:5 Sand :10 graded stone aggregate 40 mm Nominal size) and curing complete execluding cost of form work in retaining wall/breast wall the size of plum shall usually be as per HPPWD specification. with in all leads and lifts

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete In all leads and lifts 100 mm nominal bore.

Providing and fixing cast iron cowl with in all leads and lifts 100mm dia

Providing and placing in horizental layers filtering media duly graded,screened, cleaned and washed as specified:-

Top layer, Fine sand( Eff. Size 0.20mm to 0.40 and uniformity co-efficient 2.00 to 3.00).

Second layer, Coarse sand, 3mm - 6mm

Third layer : Bajri 6mm to 20 mm.

Fourth layer : Bajri 20mm to 25 mm

Bottom layer : Broken stone 50mm to 75 mm.

Providing and placing Ist class standard bricks in filter bed in two layers so as to make cross drains as per direction of Engineer-in-charge.

Providing anf fixing Bluk meter as per ISI marked. With in all leads and lifts

Providing and fixing automatic flushing cistern with a pair of CI or MS.bracket complete with fitting including CI Syphonic appratus mosquitos proof lid,CP brass unions and coupling for connecting with inlet, outlet and over flow pipes including cutting holes and making good the same. Over flow pipes to be measured and paid for separately (Viterous china 5 litres capacity)

Providing and fixing vitreous china wash down water closet(Anglo indian,W/C.pan)with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1(1cement:1 sand) (Seat and cover to be measured and paid for separately)(white colour)in all leads and lifts.

Providing and fixing 100mm size P or S trap for water closet(Squatting pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1(1cement:1 sand) Sand Cast iron in all leads and lifts.

Providing and fixing viterious china wash basin with single hole for pillar tap with CI or MS bracket painted white including cutting hole including good the same excluding fitting Cera sanitary work (Cornet) white 550x400 white in all leads and lifts.

Providing and fixing viterious china pedestral for wash basin complete recessed at the basic for reception of pipe and fittings Cera sanitary work(Carnet) white(Viterious china in white colour) in all leads and lifts.

Providing and fixing of PVC water storage tank of reputed make having capacity of 500 litres with necessary fittings including necessary inlet, outlet and scour connections and complete with float and hoisting complete in all respects.

Providing and fixing on wall faces (D-plast) PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc complete 75mm dia in all leads and lifts.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less 4.5 Kg/Sqm including fitting the joints with approved adhesive complete with in all leads and lifts and carriage of materials, 110mm nominal bore.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes(Medium grade) tube fittings and clamp including making good the wall ceiling and floor in all leads and lifts) 15mm nominal bore in all leads and lifts.

Providing and fixing full way wheel valve of following dia gun metal in all leads and lifts.

15mm dia.

Providing and fixing brass bib tap(Superior quality or heavy type) 15 mm dia in all leads and lifts.

Providing and fixing CP brass soap dish with CP.brass bracket fixed to wooden cleats with CP.brass screws.chrome plate in all leads and lifts.

Electrical installation:- Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

Group C.

Electrical installation:- Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing & capping and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

2 x 1.5 Sq. mm.

2 x 4.00 Sq. mm.

Supplying and fixing 3 pin 5/6 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

Supplying and fixing 2 way 5/6 amps. Tumbler/piano type switch on the existing switch box on the switch box/cover including connections etc. as required.

Supplying and fixing 3 pin 15/16 amps. Socket outlet on the exists switch box/covers including connections etc. as required.

S/F 15/16 Amp tumbler/piano type on the existing switch box i/c conn.

Supplying and fixing wooden box of following size (nominal) on surface or recess with suitable size of phenolic laminated sheet cover of in front as required.

229 mm.x 102 mm.x 60 mm. deep

203 mm.x152 mm.x 60 mm. deep

Providing and Supplying CFL 1 x 23 watt of reputed make in all leads and lifts.

White washing with line on undecorated walls surface two coat to give an even shade i/c throughly brooming the surface to remove the dirt ,dust ,morter and other foreign matter.

40 mm thick CC flooring 1:2:4(1 cement : 2 sand:4graded stone agg. 20 mm)laid in one layer finished with a floating coat of neat cement.

Providing and Supplying CFL 1 x 5 watt of reputed make in all leads and lifts.

Supplying and Fixing 5 Amps to 32 Amps rating, 240 Volts, L- series miniature circuit breaker of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required Cat - A. (Single Pole)

Naresh Kumar

RAM SINGH GOVT CONTRECTOR

DEVENDER KUMAR GOVT CONTRACTOR