Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹98,410Accepted-Finance | L1 | Accepted-Finance L1 | |
| 2 | L2₹98,550+₹140 (0.14%)Accepted-Finance | L2 | Accepted-Finance L2 | |
| 3 | L3₹1.0 L+₹2,376 (2.41%)Accepted-Finance | L3 | Accepted-Finance L3 |
Tender Value
₹1.1 L
EMD Value
₹2,000
Closing Date
10 Jan 2022, 2:00 pmClosed
SE, EDC, Rampur
Office of the SE, EDC, Rampur
32/2021-22(EDCR) For the work of increasing capacity of overloaded transformers under jurisdiction of EDD-BILASPUR, Rampur
2021_PVVNL_667240_1
32/2021-22(EDCR)
Open Tender
Electrical Works
Lump-sum
45 days
Office of the SE, EDC
Please refer Tender documents.
3 documents required · 3 mandatory
₹1,180
SE, EDC, Rampur
₹2,000
20 Aug 2022
29 Dec 2021
10 Jan 2022
29 Dec 2021
10 Jan 2022
29 Dec 2021
Amount
Carriage of the following material from Store Centre, Rampur to work site including loading & unloading.
11 Mtr STP Pole
Cartage of Healty Transformer from store to site, dismantling of HT & LT connection & replace of follwoing capacity T/F from substation double poles/plinth by Healthy transformer(including connection) and loading and unloading with associated work at both ends within 70 kms.
Increasing load capacity of overloaded 250KVA by Separate 250 KVA trasnformer
Double pole structure Excavation of foundation pit in size of 75x45cm having depth of 1/6th of the full length of the support(pole)Erection of support(pole) complete with providing and fixing of all clamps made of MS flat of size 75x8 mm. and other accessories(Substation angle 75*75*6*2028) . The work includes fabrication work and fixing of cross bracing sets 3.5 Mtr from MS Angle 65x65x6 mm/50x50x6 mm. The work includes cutting holes and providing MS Bolts of 16x40 mm size in the middle of the cross bracing with 1 No. sparing washer of proper size.
11 Mtr STP Pole
Grouting of support in CC 1:4:8(cement, sand & 40 mm. brick ballast) Grouting will be done in the block of size 45x45cmx1/6th of full length of the support upto ground level, 30 cm plinth above the ground level with CC 1:3:6 (cement, course sand and stone grit) with muffing. The work includes back filling and proper ramming etc. a)Double pole structure
11 Mtr STP Pole
Earthing of support with MS Earth Rod of (20x2500)mm long including excavation of pit and driving MS Rod 3.0 M apart from support and 0.5 M below the ground level and connecting below the earth electrodes with the help of GI wire No. 8SWG and earthing lugs
Make Plinth for 250 KVA Transformer with size 2*2*1.5M and CC 1:3:6 (cement, course sand and stone grit) with muffing etc. as per RESPO Norms and as per direction of Supervising Engineer.
Fencing of Plinth by providing fiber fence with 6ft Hight surrounding T/F as per RESPO Norms and as per direction of Supervising Engineer.
Providing and fixing Stone Pad
Providing Clamp with nut bolt
Providing holding clamp with nut bolt
Providing and fixing 11 KV TPMO
Providing and fixing Danger board with barbed wire including jumper
M/s Kaniska Traders
M/s Charley Enterprises
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .