Construction of Govt Sen Sec School Parwara in Tehsil Chachyot Distt Mandi SH C/o Building portion site development WS SI Septic tank soak pit harvesting system

Amount

Cutting in earth work all kinds of soils and disposal of excavated earth upto a lead of any metres such as pick work , jumper work, pick work,pick jumper blasting work, blasting work in soft and hard rock conglomrate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing out of watering/dewatering upto any lift stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in layers when required into plinth sides of foundations consolidation each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Excavation in foundation, trenches etc. in earth work in all kinds of soil such as pick work, Jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/dewatering upto any lift, stacking the excavated soil upto any lead from the edge of excavation and then returning the stacked soil in layer when required into plinth, sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Excavation in drain and channels etc. in earth work in all kinds of soils such as pick work, jumper work, pick jumper work , pick jumper blasting work , blasting work in soil and hard rock conglomerate rock or saturated soil and its intermediate classification of soil including chiseling/wedging out of rocks (where blasting is prohibited) and pumping or bailing watering/dewatering including dressing of sides and bed and disposing of excavated earth upto any leads and lifts disposted earth to be leveled and neatly dressed as directed by the Engineer-in charge within any leads including carriage of materials with in all leads, lifts and other incidentals.

Providing form work with steel plates 3.15mm(Three point fifteen millimeter) thick welded with angle iron in frame 30x30x5mm(Thirty millimeter into thirty millimeter into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and bellies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in situ-reinforced concrete and pain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in charge in:- Vertical surface such as walls(any thickness) and the like including attached pilasters, buttersses plinth and string courses and the like

Foundation, footing basis of columns etc. and mass concrete .

Flat surfaces such as soffits of suspended floors, roofs, landings and the like Floors etc upto any thickness.

Beams, cantilever, girders and lintels sides and soffits of beams, beam haunching, cantilevers, bressumers and lintels in any depth in all height from floor..

Columns, pillars, Posts and struts, Square, rectangular or polygonal in plan

Stair cases with sloping or stepped soffits excluding landing

Edges of slabs and breaks in floors and walls in any width.

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm (fourty millimetre) nominal size and curing complete excluding cost of centring and shuttering in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:5:10 (1 cement : 5 Sand :10 graded stone aggregate 40mm (fourty millimetre) nominal size and curing complete excluding the cost of form work in Foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1:4:8 ( one cement: four sand: eight graded/ crushed stone aggregate 40mm (Forty millimetre ) nominal size) mechanically mixed and vibrated and curing complete excluding the cost of form work in foundation and plinth as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Construction of dry rubble masonary for retaining walls, breast walls, revetment walls and parapets etc. for sub structure and super structure complete as per drawing and technical specification Clauses 704.6 & 1302.5, with in all leads and lilfts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

C/o Dry rubble masonry in breast wall and retaining walls revetment walls and parapets etc. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Back filling behind abutment, wing wall and retaining wall complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Boulder filling dry hand packed in under floor as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying reinforced cement concrete M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work in all leads & lifts. The mix shall be designed as per requirement of IS code and PWD specification. The design mix will be got approved from the Engineer - in - charge prior to the casting. The theoritical consmption of cement for the item shall be worked out as per approved design mix as per IS code. Foundation, footing basis of columns etc. and the like and mass concrete .

Suspended Floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and contilever.upto Floor any Level

Providing and laying reinforced cement concrete M-30(thirty) grade mechanically mixed and vibrated and curing complete excluding cost of form work in all leads & lifts. The mix shall be designed as per requirement of IS code and PWD specification. The design mix will be got approved from the Engineer - in - charge prior to the casting. The theoritical consmption of cement for the item shall be worked out as per approved design mix as per IS code. Columns, pillars posts and struts .

Providing and laying reinforced cement concrete M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work in all leads & lifts. The mix shall be designed as per requirement of IS code and PWD specification. The design mix will be got approved from the Engineer - in - charge prior to the casting. The theoritical consmption of cement for the item shall be worked out as per approved design mix as per IS code Stair cases (except spiral stair cases) excluding landing but including preparing of the top surface and finishing of nosing upto Floor any Level

Providing and laying reinforced cement concrete M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work in all leads & lifts. The mix shall be designed as per requirement of IS code and PWD specification. The design mix will be got approved from the Engineer - in - charge prior to the casting. The theoritical consmption of cement for the item shall be worked out as per approved design mix as per IS code Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses,plinth and string courses etc.

Providing and laying reinforced cement concrete design mix M-20 (twenty) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be designed as per requirement of IS code and PWD specification. The design mix will be got approved from the Engineer - in - charge prior to the casting. The theoritical consmption of cement for the item shall be worked out as per approved design mix as per IS code upto floor all level including carriage of material within all leads, lifts and other incidentals. Suspended Floor roofs, landing and shelves and their support balconies, beams,girders, bressumers and contilever.

Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses,plinth and string courses etc.

Providing and laying reinforced cement concrete design mix M-20 (twenty) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforced cement concrete work. The mix shall be designed as per requirement of IS code and PWD specification. The design mix will be got approved from the Engineer - in - charge prior to the casting. The theoritical consmption of cement for the item shall be worked out as per approved design mix as per IS code in string course, copings, bed plates, anchor blocks, plain windows sills and the likesu upto floor all level including carriage of material within all leads, lifts and other incidentals.

Providing and laying reinforced cement concrete design mix M-20 (twenty) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforced cement concrete work. The mix shall be designed as per requirement of IS code and PWD specification. The design mix will be got approved from the Engineer - in - charge prior to the casting. The theoritical consmption of cement for the item shall be worked out as per approved design mix as per IS code in string course, copings, bed plates, anchor blocks, plain windows sills and the likesu upto floor all level including carriage of material within all leads, lifts and other incidentals.

Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire up to any level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg. (two point seventy five kilogram) of cement per sq.metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying 20 cm. (twenty centimetre) thick composit stone masonry with stone facing of chisel dressed stones one line dressed in cement mortar 1:6(1 cement :6 sand) and concrete backing with cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stoneaggregate 20 mm (twenty millimetre) nominal size on inner face of walls including centring,shuttering and propping complete up to floor level as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . upto Floor any Level

Precast concrete block masonry in partition walls 10 cm (ten centimetre) thick with solid block of approved size (including quoin blocks, jamb blocks, closer etc)made of cement Concrete, 1:3:6 (One Cement: Three Sand: Six graded stone aggregate.) 40 mm (Forty millimeter) nominal size and down gauge in cement mortar 1:6 (One Cement: Six Sand) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . upto Floor any Level

Precast concrete block masonry in partition walls 10 cm (ten centimetre) thick with solid block of approved size (including quoin blocks, jamb blocks, closer etc)made of cement Concrete, 1:3:6 (One Cement: Three Sand: Six graded stone aggregate.) 40 mm (Forty millimeter) nominal size and down gauge in cement mortar 1:6 (One Cement: Six Sand) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals . upto Floor any Level

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position 1st class Deodar wood as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Brick work using common burnt clay building bricks in foundation and plinth in Cement mortar 1:6 (One Cement : Six Sand) second Class Bricks as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Half brick masonry in common burnt clay building bricks in Cement Mortar 1:3 (one cement : three sand) Second Class Brick as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals .

Providing and fixing 35 mm (thirty five millimetre) thick including black enamelled M.S. butt hinges flush door shutters interior grade, commercial type, core of black-board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutters as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 30 mm (thirty millimetre) thick including black enamelled M.S. butt hinges flush door shutters interior grade, commercial type, core of black-board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutters as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 2nd class deodar wood wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six millimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screw etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing 40x3 mm (fourty into three millimetre) flat iron hold fast 40cm (fourty centimetre) Long including fixing to frame with 10mm (ten millimetre) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30 x 10x15cm (thirty into ten into fifteen centimetre) 1:3:6 (1 cement : 3 sand: 6 graded stone aggregate 20mm(twenty millimetre) nominal size as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.300x16mm (three hundred x sixteen millimetre) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing anodized aluminum tower bolts (barrel type ) anodized trans parent or dyed to equired shade and colour with screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 250x10mm (Two hundred fifty into ten millimeter)

150x10mm (One hundred fifty into ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Plain M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Inside lining of PGI sheet with necessary screws etc. as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing on wall black board of 210x105 cm (two hundred ten into one hundred five centimetre) clear size made of phenol bond particle board 12mm (twelve millimetre) thick as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

6mm (six millimetre) Cement plaster to ceiling in Cement Mortar 1:4 (1 Cement : 4 Sand) as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

6mm (Six millimeter) cement plaster to ceiling in cement mortar 1:3 (one Cement : three Sand) as per the directions of Engineer-in-Charge including carriage of materials within all leads, lifts and other ncidentals.

15mm (fifteen milimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to all floor level includingarises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:six sand)as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement:6 sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

15mm (fifteen milimetre) cement plaster in single coat on the fair side of brick/concrete/stone wall for interior plastering upto floor all level including arises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth in cement mortar 1:4 (one cement:4 sand) as per the direction of Engineer-in-Charge including carriage of materials within all leads, and lifts other incidentals.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing M.S.fan clamp type -1 of 16 mm (sixteen millimetre) dia M.S. bar bent to shape with hooked ends in R.C.C slab during laying including painting the exposed portion of loop,all as per standard design complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including t horoughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Distempering with dry distemper of approved brand and manufacture(Two coats)and of required shade on undecorated wall surface to given an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing angle iron cupboard frames frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in- Charge.

Providing and fixing 19mm (nineteen millimetre) thick Commercial Board water proof shutters with 6mm (six millimetre) thick hard wood edging for cup boards i/c fixing with nickel plated piano hinges with screws etc complete as per specification and as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing M.S hooks and eyes as per the directions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. 250mm (Two hundred fifty millimeter)

200mm(Two hundred millimeter)

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting Readymixed paint brushing wood primer pink as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

Painting two coats (excluding priming coat)on new wood and wood based surfaces,with readymixed paint,brushing to give an even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping Readymixed paint other then white as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals.

40 mm (fourty millimetre) thick Cement concrete flooring 1:2:4 (1 cement : 2 sand:4 graded stone aggregate 20 mm (twenty millimetre) nominal size laid in one layer finished with a floating coat of neat Cement as per the directions of Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals. Upto floor any level.

25 mm (twenty five millimetre) thick wooden flooring of 1st class deodar wood laid over C.C. slab (to be paid separately) ( thinly coated with thin layer of hot bitumen blown type) @ 2.45 kg per sq m (two point forty five kilogram per squaremetre) including fixing of wooden planks in position over wooden plugs fixed in c.c. floor including planning and levelling complete as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.Up to Floor any level.

Kota stone slab flooring 25 mm (twenty five millimetre) thick kota stone on 20 mm (twenty millimetre) (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing completeas per directionof Engineer-in Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Kota stone slab 25 mm (Twenty five millimeter ) thick in risers of steps,skirting dado and pillars laid on 12 mm (twelve millimetre) (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete within all leads, lifts and other incidentals and as per the directions of Engineer-in-Charge. upto floor any level.

Providing and laying 8 mm (eight millimetre) thick Anti Skid Ceramic tile 300 x 300 mm (three hundred into three hundred millimetre) of AGL/Johnson/Kajaria/Orient Bell or equivalant manufactured of approved shade and colour in flooring, treads of steps and landing laid over 12mm (twelve millimetre) thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and laying 10mm (ten millimetre) digital ceramic tile of size 300 x 600 mm (three hundred into six hundred millimetre) in skirting risers of steps and dados on 8 mm (eight millimetre) thick cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete. as per directionof Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. upto floor any level.

Providing and fixing wall panelling of 12 mm( Twelve Millimeter Meter) thick Pre-Laminated Particle Board (one side) of approved brand on soft wood 40 x 40 mm (forty into forty millimetre) @ 600 x 600 mm (six hundred into six hundred millimetre) c/c on both side fixing with rawl plugs on wooden pegs and screwed and showing 8mm (eight millimetre) wide and 12 mm (twelve millimetre) deep grooves of required pattren in elevation and finished teak wood polished beeding out of 25 x 12 mm (twenty five into twelve millimetre) and cornice of size 75 x 60 mm (seventy five into sixty millimetre) of different pattren in top middle and corner joints including polishing and painting groove complete as per direction of Engineer in-Charge including carriage of materials with in all leads and other incidentals. upto floor any level.

Providing and fixing Glass reinforced concrete (GRC) screen in approved size, pattren, design, thickness and colour of M/S unistone make or equivalent the screen should be made from " 53 grade " white portlant cement manufactured by "JK cement" or equivalent quartz fine silica sand, alkali resistant glass fiber manufacture ny saint Gobain or equivalent super plasticizer manufacure by BASF or equivalent polymers manufacure by BASF or Equivalent and UV resistant synthetic inorganic pigments should be used for pigmentation manufactured by BAYFERROX (Germany) or equivalent the material casting should take place in synthetic rubber/FRP mould manufacture by Recki or equivalent. The fixing of screens should be dry fixing i.e. to be done with stainless steel (SS-304) L-shaped clamps dash fastners and pins as per design and instructions of Engineer-in-Charge.

Providing and fixing square edges cover fillets (beading) 19mmx6mm (nineteen millimetre into six millimetre) section including mitring at junctions with wood screws and nails complete as per direction of Engineer in-Charge including carriage of materials with in all leads and other incidentals.

Providing and fixing 0.60mm (Zero point six zero milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) micons primer coating to back coast of polyester of 5 microns over 5 microns primer coating including fixing with screws, prepainted iron J or L hooks, bolts and nuts 6mm(six milimetre) dia with prepainted limpet and rubber washer complete with all accessories as required as per specifications and as per direction of Engineer-in-Charge including carriage of materials with in all leads, liftsother incidentals.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60 mm (Zero point sixty millimeter) thick preprinted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat or regular modified polyester organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with preprinted iron J or L hooks, bolts & nuts 6mm(Six millimeter) dia and preprinted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing valley 90 cm (Ninety centimeter) overall 0.60mm (Zero point sixty millimeter) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge.

Providing and fixing flushing 38cm (thirty eight centimetre) overall with 0.60mm (Zero point sixty millimeter) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing and fixing on wall face 100mm (One hundred milimetre) dia PVC(D-Plast) rain water pipes of working pressure not less than 4.5 Kg/sqm (Four point five kilogram per square metre) including filing the joint with approved adhersive complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing and fixing on wall face (D-Plast) accessories for rain water pipes including filling the joint with approved adhesive complete as per the direction of Engineer-in-Charge of materials within all leads, lifts and other incidentals. PVC Plain Bend 100mm(One hundred milimetre) dia.

Shoe 100mm dia(One hundred milimetre) dia.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point six six millimetre to two millimetre) thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Steel work welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In trusses and trussed purlins in buildings as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing under layer for plinth protection of 75mm (seventy five millimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm (fourty millimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Providing plinth protection 50mm (fifty millimetre) thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm (twenty millimetre)nominal size as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals.

Constructing course rubble dressed "U" shape open surface drain with side wall 15X22cm (fifteen into twenty two) in cement mortor 1:6 (one cement: six sand) and in side plstring with cement plaster 1:3 (one cement : three sand ) including earth work and laying 10cm (Ten Centimetre) cement concrete 1:5:10 (one cement :five sand:ten graded stone aggregate 40mm (Forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4(one cement :two sand ;four graded stone aggregate 20mm (Twenty millimetre) nominal size) and finishing with a floating coat of neat cement and curing complete as per standard design as per the entire satisfaction and direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 75mm x 60mm (seventy five millimetre into sixty millimetre) hand rails in 1st class Indian teak wood straight length complete as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

Providing and fixing MS Railing for staircase having balluster of 20mm x 20mm (twenty millimetre into twenty millimetre) square Bars with a clear height of 85cm (eighty five centimetre) embeded in cement concrete steops and jointed with electrical/gas welsing at top along with MS flat of 40 x 6 mm (forty into six millimetre) the balluster welded/jointed with two number MS flat of 40 x 5 mm (forty into five millimetre) size complete with a priming coat of red lead paint as per drawing and specification and as per the direction of Engineer-in-Charge including carriage of materials within all leads, lift and other incidentals.

Providing and laying 20 mm (twenty millimetre) nominal bore trenches, galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing plythelineo-aluminiumo-polythelene(PE-AL-PE) composite pressure pipe U.V.stabilized with carbon black confirming to IS-15450-2004 water supply including clamp at one meter spacing,cutting,fixing and making good the wall etc.but excluding the cost of fittings(internal work) pipes exposed on wall.internal worko-exposed on wall. (KITEC make) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 1620 (one thousand six hundred twenty) 20 mm (twenty millimetre) OD pipe

1216 (One thousand two hundred sixteen) 16mm (sixteen millimetre)O.D.Pipe.

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees, elbows, reducers, connectors,couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc. (KITEC make) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. Equal tees i)1216 (one thousand two hundred sixteen)

Reducing tees 1620 (one thousand six hundred twenty) x all branches

Female branch TEE i)1216x1216x15mm (one thousand two hundred sixteen into one thousand two hundred sixteen into fifteen millimetre) thread.

Female elbows i)1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread.

Female elbows ii)1620x15mm (one thousand six hundred twenty into fifteen millimetre) thread.

couplers i) 1216 (one thousand two hundred sixteen).

couplers ii) 1620 (one thousand six hundred twenty).

Providing and fixing PVC water storage tank of ISI:12701 marked,G.I.inlet and outlet connection,15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level:-1000 (one thousand)litres capacity. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc complete. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 150 mm (one hundred fifty millimetre) nominal size.

110mm (one hundred ten millimetre) nominal size.

75 mm (seventy five) nominal size.

Providing and fixing PVC double equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete icluding fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 110mm (one hundred ten millimetre) dia

75 mm (seventy five) dia

Providing and fixing PVC door bend with ovel access door ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 110 mm (one hundred ten millimetre) dia

75 mm (seventy five millimetre) dia

Providing and fixing PVC collar, ISI marked including fixing with approved adhesives etc.with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 110mm (one hundred ten millimetre) nominal size.

75 mm (seventy five millimetre) nominal size.

Providing and fixing PVC plain bend, ISI marked including fixing with approved adhesives etc. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 110mm ( one hundred ten millimetre) nominal size.

75 mm (seventy five millimetre) nominal size.

Providing and fixing PVC clamps, ISI marked of approved design with steel screws and rawal plugs etc. Complete. with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 110mm (one hundred ten millimetre) nominal size.

75 mm (seventy five millimetre) nominal size.

Providing and fixing PVC floor trap ISI marked of self cleansing design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. . with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge. 110 mm x 90 mm (one hundred ten millimetre into ninty millimetre) size

110 mm x 75 mm (one hundred ten millimetre into seventy five millimetre) size

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type W.C pan) size 580mm (five hundred eighty millimetre) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately). Orissa pattern (Cera) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing vitreous china water closet(European type w.c.pan) with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement:1sand)(seat and cover to be measured and paid for seprately):-(Cera) Anglo indian universal closet with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 100 mm (hundred millimetre) size 'P' or 'S' trap for water closet (squatting pan)including jointing the trap with the pan and soil pipe in cement mortar 1:1(1 cement : 1 sand) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

P/F PTMT coloured/white high density polyethylene/poly propylene 10 (ten) litres capacity ( full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, syphon, 15mm (fifteen millimetre) nominal size PVC ball valve with polythene float,with push button, couplings for connections with inlet,outlet and overflow pipe, 40mm (forty millimetre) dia C.P.flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for seprately) with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing G.I. Inlet connection for flush pipe with W.C. Pan with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 32mm (thirty two millimetre) dia M.I. Union for wash basin or sink with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 32mm (thirty two millimetre) dia C.P. Bottle Trap for wash basin and sink with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 32mm (thirty two millimetre) dia C.P Brass waste for wash basin or sink with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing 100 mm (hundred millimetre) dia cromium plated grating of superior quality for floor, gully or nahani trap with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing automatic flushing cistern with a pair of C.I. Or M.S. brackets complete with fittings including C.I. Syphonic apparatus, mosquito proof lid, C.P. Brass unions and coupling for connections with inlet, outlet and overflow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) Vitreous China 5 ltr. (five liters) capacity with in all leads and lifts and other incidentals and as per the direction of the Engineer-in Charge.

Providing and fixing division plate for urinals 600mm x300mm (six hundred millimetre into three hundred millimetre) virterous china including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. (Jaquar or ESS-ESS)

Providing and fixing PTMT urinal waste coupling of approved quality and colour including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing 15 mm (fifteen millimetre) nominal bore C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clanmps etc. (all in C.P. Brass) including cutting holes and makng good the same including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT urinal cock of approved quality and colour 15 mm (fifteen millimetre) including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260mm x 350 (four hundred thirty into two hundred sixty millimetre into three hundred fifty) and 340x430x265mm (three hundred fourty into four hundred thirty into two hundred sixty five millimetre) sizes, respectively with authomatic flusing cistern with fittings R.S or C.I. Brackets standard size galvansied steel flush pipe and spreaders galvanised steel flush pipe and spreaders with brass unions and G.I. clamps complete, inciuding painting of cistern and fittings, cutting and making good the walls floors where required Range of two urinal basins with 10 litres C.I. Automatic flushing cistern including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT High quality dule hanging bath room mirror of 4 mm (four millimetre) thick glass of approved quality and colour with steel screws and rawal plugs etc complete size 600 mm X 450 mm (six hundred millimetre into four hundred fifty millimetre) including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT toilet rail of approved quality and colour 600 mm (six hundred millimetre) long with steel screws and rawal plugs etc complete including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT toilet paper holder of approved quality and colour with steel screws and rawal plugs etc complete including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT soap dish with holder of approved quality and colour with steel screws and rawal plugs etc complete including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT bib cock of approved quality and colour standard size 15 mm (fifteen millimetre) including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT pillar cock fancy of approved quality and colour 15 mm (fifteen millimetre) including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT stop cock of approved quality and colour 15 mm(fifteen millimetre) with male / female thread including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT angle cock of approved quality and colour 15 mm (fifteen millimetre) with flange including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing PTMT ball valve of approved quality and colour including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge. 15 mm (fifteen millimetre) nominal bore.

20 mm (twenty millimetre) nominal bore.

Providing and fixing 300/450mm (three hundred/four hundred fifty millimetre) length 15mm (fifteen millimetre) nominal bore P.V.C connection pipe with brass unions with in all leads and lifts and as per the direction of Engineer-in-Charge.

Constructing manhole with R.C.C top slab in 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size) foundation concrete 1:4:8 (one cement : four sand : eight Graded stone aggregate 40mm (forty millimetre) nominal size ) inside plastering 15 mm (fifteen millimetre) thick with cement mortar 1:3(one cement : three sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size finished smooth complete including curing and testing (i)inside size 800mmx800mm (eight hundred millimetre into eight hundred millimetre) and 500 mm (five hundred millimetre) deep including C.I. cover with frame( light duty single (seal ) pattern I) 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) A)with 200 mm(two hundred millimetre) thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (one cement : three sand )with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing plastic seat (Solid/ Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers white plastic seat and cover including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings Flat back 630mmx450mm (six hundred thirty millimetre into four hundred fifty millimetre) including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing vitreous China padedstal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Supplying cast iron cover with frame for manhole for frame of internal dimension 455 x 610 mm (four hundred fifty five into six hundred ten millimetre) rectangular CI cover the weight of cover to be not less than 38 kg (thirty eight kilogram) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing kitchen sink with C.I. Or M.S brackets, painted white including cutting holes in walls and making good the same but excluding fittings Vitreous China 600mm x 450 x 250 mm (six hundred millimetre into four hundred fifty into two hundred fifty millimetre) including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

Suppliying cast iron cover without frame for manholes For frame of internal dimension 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) rectangular C.I. cover (light duty single seal pattern-1) the weight of cover to be not less than 23kg (twenty three kilogram) including carriage of materials with in all leads and lifts and as per the direction of Engineer-in-Charge.

ATUL SHARMA