As and As to Building No. P - 12, Visakhapatnam

Amount

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc and removing rubbish to a distance not exceeding 1.50 KM complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and not exceeding 1.5m deep in Soft / Loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for RCC M–30 Design Mix, using 20mm graded stone aggregate as in foundations including Pile Caps, Rafts, Footings, Foundation Beams, Plinth Beams, Bases for Columns etc. complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc. complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span etc. complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Slabs supported on walls, beams, columns, landings, shelves, Chajjas and the like complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

Use and removal of steel formwork to sides of concrete foundations, pile caps, footings, bases of columns, raft and raft beams, sides and soffits [if any] of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed.

Use and removal of steel formwork to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for fair finished surfaces of concrete complete all as specified and as directed.

Use and removal of steel formwork to sides and soffits of floor or roof beams, beam launchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, splays between floors and beams and similar works for fair finished surfaces of concrete complete all as specified and as directed.

Use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including fair finished surfaces complete all as specified and directed.

M & L for providing Precast RCC 1:2:4, Type B-1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], Chullah hoods, Chajjas, water troughs, mangers, Shelves and similar articles with plain faces set in cement mortar 1:6 complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 6mm dia bars at every fourth course of brick work complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, including mixing water proofing compound as per manufacturers instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only Integral Water Proofing Compound [ISI marked] of approved make.

S & F Rolled Mild Steel work conforming to Fe 410-W, Grade-E- 250, Quality-A, as in Joist, Channel, Angle, or Tee Sections, fixed independently, without connecting plates etc [cut to ordinary lengths i.e. within 20mm of the length indicated] complete all as specified and as directed.

S & F Rolled Mild Steel work conforming to Fe 410-W, Grade-E- 250, Quality-A as in Plates [Plain & Chequered], Channels, Angles, square cut or notched [ordinary or counter sunk] forming holes without any attachment including fixed with Nut and Bolt / welding complete all as specified and as directed.

S & F MS machine made screw bolts with hexagonal or square head one end and screwed other or screwed both ends, fitted with washers and one hexagonal or square nut exceeding 30 cm long and dia of neck exceeding 20 mm complete all as specified and as directed.

Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris to a distance not exceeding 1.50 KM complete all as specified and as directed.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size exceeding 0.42 Sq.m and not exceeding 1.00 Sq.m, 10 mm thick as in Floors, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Vitrified Tiles, Double Charged, Coloured, Premium Quality, of size exceeding 0.42 Sq.m and not exceeding 1.00 Sq.m, 10 mm thick as in Vertical Surfaces such as Skirting, Dado etc, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 600 mm X 300 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Window Cills, Cooking Platform etc., and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Steps, Window Cills, Cooking Platform etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.m each and removing to store complete all as specified and as directed.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each and removing to store complete all as specified and as directed.

S & F Fiber Glass Reinforced Plastic [FRP] Door Frame of Cross Section 90 X 45mm and having Single Rebate of 32 X 15mm to receive Shutter of 30mm thick, the laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat, Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all styles and rails, the frame shall be covered with fiber glass on all sides, MS stays shall be provided at bottom of styles to steady the frame complete all as per manufacturer's instructions, as specified and as directed.

S & F 30mm thick Fiberglass Reinforced Plastic [FRP] Flush Door Shutter of approved Solid Colours or Wooden Finish made with fire retardant grade unsaturated polyester resin, moulded with 3mm thick FRP Laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam [PUF] / Polystyrene Foam filler material throughout the hollow panel, casted monolithically with testing parameters of FRP laminate conforming to Table 3 of IS - 14856 complete all as per manufacturer's instructions, as specified and as directed.

S & F Factory made UPVC Sliding Window, Three Track, Coloured of area not exceeding 2.0 Sq.m, made of extruded profiles with wall thickness of 2.3mm±0.2mm, Window profile with hollow section with multi chamber, Frame of size 88mm X 52mm, Sliding Sash of size 42mm X 67mm, Sliding Mesh Sash of size 42mm X 57mm, Sliding Interlock [One vertical length in each shutter] of size 45.50mm X 28mm, Glazing Bead of size 24.50mm X 16mm shall be mitred cut and fusion welded at all corners, including drilling holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM Gasket, 1.2mm±0.2mm thick Galvanized Steel Frame of size 30mmx 18mm, 2 Nos, Sliding Sash of size 30mm x 18mm, Sliding Mesh Sash of size 26mm x 10mm profile to be inserted in required profile, frame shall be fixed to the wall with 8mm X 100mm long fasteners, Hardware such as Touch lock of zinc alloyed [white powder coated], Steel roller system, Stainless Steel Wire Cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories shall be provided with proper operative and locking hardware mechanism, frame shall be fixed to wall with high quality fasteners and silicon glue shall be applied to fill up gap between frame and wall to make leak proof complete all as specified and as per Manufacturer instructions. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.

S & F Factory made UPVC Door Frame made of UPVC extruded sections having an overall dimension [Extruded Section Profile] 42x50 mm [Tolerance ± 1 mm], with wall thickness 2.0 mm [± 0.2 mm], Corners of the Door Frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded, the hinge side vertical of the frames reinforced by galvanized M.S. Tube of size 19 X 19 mm and 1mm [± 0.1 mm] wall thickness and 3 Nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as directed.

S & F 30 mm thick Factory Made Polyvinyl Chloride [PVC] Door Shutter made of styles and rails of a UPVC Hollow Section of size 60 X 30mm and wall thickness 2 mm [± 0.2 mm], with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of MS galvanised / plastic brackets of size 75 X 220 mm having wall thickness 1.0 mm and stainless steel screws, the styles of the shutter reinforced by inserting galvanised MS tube of size 25 X 20mm and 1 mm [± 0.1 mm] wall thickens, the Lock Rail made up of 'H' Section, a UPVC hollow section of size 100 X 30mm and 2mm [±0.2 mm] wall thickness fixed to the shutter styles by means of plastic / galvanised MS 'U' Cleats. The shutter frame filled with UPVC multi chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm [± 0.1 mm] wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised MS rod and fastened with nuts and washers, complete as specified by the manufacturer and as directed.

Supply only 4mm thick Sheet Glass ordinary quality in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S & F Powder Coated Aluminium Deco Grill of Model / Design No. DG 104 including Powder Coated Aluminium Channel of size 30 X 12 X 1.5mm for fixing Deco Grill complete all as specified and as directed.

M & L for PCC 1:2:4, Type B-1, using 20 mm graded stone aggregate as in Bed blocks and Bed plates including weathering, slightly rounded or chamfered angles and throating, necessary form work etc complete all as specified and directed.

S & F Mild Steel work confirming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

S & F Stainless Steel Railing made with Stainless Steel Pipes of wall thickness not less than 1.6mm, of Grade AISI 304, standard quality, bright polish finish, using 50mm dia pipes for hand rail, 25mm dia pipes for vertical supports / balusters and 25mm dia pipes as in tie bars in three layers, SS tubes shall be welded at the turnings and junctions, welded portions shall be completely grinded and brought to bright and smooth finish including all bends, elbows, making holes in the floor / steps, grouting with epoxy to achieve full strength of railing complete all as specified and as directed.

S & F second class hard wood plain, plain fillets / Beading, square, rectangular or triangular in section, wrought, secured with screws around Chowkats, cross sectional area exceeding 13 Sq.cm and not exceeding 25 Sq.cm complete all as specified and as directed.

S & F 18mm thick Plywood, Grade BWR, Type BB, fixed with screws to Wooden Frames as in Cupboard Shutters complete all as specified and as directed.

S & F 1.5 mm thick Decorative Laminate, Type - 1 of Surface Finish, Colour and Pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

S & F 125 mm size, Butt hinges, extruded Brass, with mild steel hinge pin, bright polished, Type B-12 including fixtures complete all as specified and as directed.

S & F Brass barrel Tower Bolt of size 150 mm size with cast or sheet barrel and rolled or cast bolts complete all as specified and as directed.

S & F Brass Handles, Cast Type, Polished Bright of size 150mm long complete all as specified and as directed.

S & F Brass Handles, Cast Type, Polished Bright of size 100mm long complete all as specified and as directed.

S & F Brass Sliding Door Bolt with sand or die-cast brass hasp, staple [Bolt Type] of size 300 mm and fixing bolt with rolled or drawn brass bolts complete all as specified and as directed.

S & F 40mm dia Polished Brass Cupboard Knobs fixed with nut, screw and washer complete all as specified and as directed.

S & F AISI 304 Grade Stainless Steel Telescopic Channels with rollers of approved make complete all as specified and as directed.

S & F Harrison Rails [Curtain Rails], AISI 304 Grade Stainless Steel, 20 mm dia with fixing brackets, stops, rollers etc complete all as specified and as directed.

S & F Harrison Rails [Curtain Rails], AISI 304 Grade Stainless Steel, 25 mm dia with fixing brackets, stops, rollers etc complete all as specified and as directed.

S & F GI water tubing of 15 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F GI water tubing of 20 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F GI water tubing of 25 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 MPa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed.

S & F Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 MPa, 20 mm bore with iron wheel head, screwed both ends for iron pipe, confirming to IS, ISI Marked complete all specified and as directed.

S & F Angle Cock, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, screwed down high pressure with crutch or butterfly handle for iron pipe etc. complete all as per Jaquar Catalogue No. CON-059KN or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as per Jaquar Catalogue No. OPP-15001PM or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Two way Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. FLR-5041N or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Bib Taps, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type, Short Body with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as per Jaquar Catalogue No. QQT-7037 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Health Faucet with 1 m long flexible tube, wall hook, non return valve complete as per Jaquar Catalogue No. ALD-CHR-585 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Stainless Steel, Tubular Towel Rail, D Type, 600 mm long between flanges complete all as per Jaquar Catalogue No. ACN-1111SM or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Stainless Steel Towel Ring complete all as per Jaquar Catalogue No. ACN-1121N or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Stainless Steel, Towel Rack 600mm Long with Lower Hangers complete all as per Jaquar Catalogue No. ACN-1181S or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Stainless Steel, Soap Dish, Fancy Type complete all as per Jaquar Catalogue No. AKP-35731P or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Corner Glass Shelf with Bracket complete as per Jaquar Catalogue No. ACN-1173 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Cast Copper Alloy, Chromium Plated Hot and Cold 15mm dia Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, Connecting Legs & Wall Flange including Hand & Overhead Shower as per Jaquar Catalogue No. QQT-7281 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Vitreous China Ware Wash Hand Basin, White, Thin Rim Table Top Basin type of size 480 x 480 x 135mm including 32mm dia Brass Chromium Plated Waste Fittings [Jaquar Catalogue No. ALD-705] with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings, PVC Connection of 15mm Bore and 600mm long with Brass Check Nut and Union etc. complete all as specified and as directed. Make: Model No. OPS-WHT-15901N of Jaquar or equivalent in Kohler / Roca / Hindware [Italian Collection] / Parryware [Superfine] / Johnson Pedder

S & F Bottle Trap with Internal Partition, 32mm Size with 250mm & 190mm Long Wall Connection Pipes & Wall Flange having minimum water seal of 25mm complete as per Jaquar Catalogue No. ALD-769L250x190 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Stainless Steel Toilet Paper Holder, Chromium plated, Fancy type complete all as per Jaquar Catalogue No. ACN-1153S or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F Vitreous China Single Piece Wash Down Water Closet [Pedestal Pattern], of White Colour, Rimless Single Piece with UF Soft Close Seat Cover, Tornado Flushing, Hinges, Fixing Accessories and Accessories Set, Cistern Fittings, S Trap-300 mm, PVC Connection of 15mm Bore and 600mm long with Brass Check Nut and Union etc. complete all as specified and as directed. Make: Model No. OPS-WHT-15851SN of Jaquar or equivalent in Kohler / Roca / Hindware [Italian Collection] / Parryware [Superfine] / Johnson Pedder

S & F Maze Overhead Shower of 300x300mm Square Shape Single Flow [Body & Face Plate Stainless Steel with Chrome Finish] with Rubit Cleaning System complete all as per Jaquar Catalogue No. OHS-CHR-1639 or its equivalent in Marc / Kohler / Cera / Parryware / Grohe / Crabtree / Blue Star & Silver Shine complete all as specified.

S & F 100mm size Stainless Steel grating for Floor Traps complete all as specified and as directed.

S & F Stainless steel kitchen sink with drainage board, made of stainless steel sheet of 1 mm thick, with plugs, washers, Waste Fittings, 32 mm dia, Brass, Chromium plated, and 32mm dia PVC flexible Waste Pipe, 750 mm long, including bedding in Cement Mortar to dwarf wall or including fixing cantilever CI Brackets and connecting union to waste pipe, over all size 915 mm x 460 mm, Bowl size 410 mm x 355 mm x 165 mm complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S & F Sand Cast, Cast Iron, soil / waste / vent pipes, 50mm bore, in any length with or without ears, jointed with cement sand mortar, laid in trenches or in floors complete all as specified and as directed.

S & F CI Bends [any radius] with duck's foot or heel rest of 50mm bore, for Cast Iron soil / waste / vent pipes complete all as specified and as directed.

S & F 50mm dia out let, Cast Iron Floor Trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4, Type B-1 complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Triple Layered, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed.

S & F Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe [Minimum Weight 15mm - 210 Grams] etc complete all as specified and as directed.

M & L for preparing newly plastered Wall / Ceiling surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying and applying two coats of Plastic emulsion paint over a coat of alkali resistant primer on Wall / Ceiling surfaces complete all as specified and as directed. Make: Royale by Asian Paints

M & L for Complete removal of existing treatment of any description on Wall / Ceiling surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Plastic emulsion paint over a coat of alkali resistant primer complete all as specified and as directed. Make: Royale by Asian Paints

M & L for preparing newly plastered Wall / Ceiling surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] over a Coat of Weather Proof Exterior Primer of same manufacturer as that of paint on Wall / Ceiling surfaces complete all as specified and as directed.

M & L for Complete removal of existing treatment of any description on Wall / Ceiling surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] over a Coat of Weather Proof Exterior Primer of same manufacturer as that of paint on Wall / Ceiling surfaces complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for preparing newly plastered Wall / Ceiling surfaces and applying two or more coats of Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper over a coat of alkali resistant primer on Wall / Ceiling surfaces complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment along external walls below concrete or masonry apron using chemical emulsion @ 2.25 litres per RM by drilling 12 mm dia holes up to 300 mm deep and 300 mm centre to centre including plugging holes complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed.

M & L for 25 mm average thick, PCC 1:2:4, Type B-0, using 10mm graded aggregate as in Padding over roof slabs etc. including mixing water proofing compound as per manufacturers instructions and finishing the top surface rough complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering 10mm thick in cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of cold applied bituminous primer @ 0.50 KG per Sq.m, applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m, laying Polymeric water proofing membrane of weight not less than 3.00 Kg per Sq.m reinforced with polyester non-woven fabric of weight not less than 150 Grams per Sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m and finished with a coat of bituminous aluminium paint @ 100 grams per Sq.m on top for water proofing treatment complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

S & F 12mm thick Frosted Toughened Glass Partition fixed with suitable AISI 304 Grade Stainless Steel Cleats, fixing arrangements on all sides of the partition for gapless fixing complete including grinding the edges complete all as specified and as directed.

S & F 10mm thick Frosted Toughened Glass as in Staircase Railing fixed to Stainless Steel Railing with 25mm size Stainless Steel Studs complete including grinding the edges, all as specified and as directed.

S & F 12mm thick Frosted Toughened Glass Door fixed with Pivots Hinges, Hydraulic Floor Door Spring etc. Including Handles on both sides, 300mm long made with 25mm dia Stainless Steel pipe of Grade AISI 304 complete including grinding the edges complete all as specified and as directed.

M & L for finishing External Walls with Exterior Textured Paint of approved Shade and Pattern / Design in Two or more coats applied @ 3.28 Litres per 10 Square Metres over a coat of Exterior Primer applied @ 2.2 KG per 10 Sq.m complete all as specified and as directed.

M & L for finishing Internal Walls with Interior Textured Paint of approved Shade and Pattern / Design in Two or more coats over a coat of Interior Primer complete all as specified and as directed.

S & F Seamless False Ceiling Frame Work using GI perimeter channels of 0.55 mm thick, having one flange of 20 mm and another flange of 30 mm and web of 27 mm along the perimeter of the ceiling, fixed to wall with nylon sleeves and screws at 610 mm intervals, GI intermediate channels of size 45 mm X 15 mm X 0.90 mm supported with GI ceiling angles of size 25 mm X 10 mm X 0.55 mm fixed to soffits with steel expansion fasteners / GI cleats at 1220 mm intervals, ceiling section of 0.55 mm thick having knurled web of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm fixed to intermediate channel with connecting clips and in direction perpendicular to the intermediate channels at 457 mm centre to centre including fixing Gypsum Board of 12.5 mm thick conforming to IS – 2095 for false ceiling, fixed to ceiling section with 25 mm dry wall screws at 230 mm centers and including applying Two Coats of Plastic Emulsion Paint over a coat of Alkali Resistant Primer and also including Dismantling of Wall & Ceiling Boards [Fibre / Pulp / Insulation etc] of any description or Insulation Boards / Slabs / Blankets including cover fillets complete all as specified and as directed.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. and Modular Type Pressed Metal Flush Box made out of 2mm thick MS Sheet of suitable size and including Modular type Base / Grid Frame & Cover Frame for housing Modular Type Switches, Sockets and Regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point controlled by One Switch complete all as specified. Note: Rate quoted is also deemed to be including cost of Cutting chases, pinning in Brick Walls, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, Cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

All as per Serial Item No. 105 above but One 3 Pin Switch Socket Outlet 6 Amps on Independent Board complete all as specified.

All as per Serial Item No. 105 above but for One 3 pin Socket Outlet 6 Amps on the Same Board with other switches complete all as specified and as directed.

All as per Serial Item No. 105 above but one 3 Pin Switch Socket Outlet 16 Amps on independent board, with 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 16 Amps, 230 Volts complete all as specified and as directed.

S & F Ceiling Rose, Surface Bakelite, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 3 Pin, 6 Amps, Modular Type, Two Modules, 230 Volts, complete all as specified and as directed.

S & F Socket Outlet, 3 pin, 16 Amps and 1 pin, 5 Amps, Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

S & F Electronic Fan Regulator, Stepped Type, Modular Type, One Module, 120 W, AC, 230 Volts, Single Pole complete all as specified and as directed.

S & F Bell, Ding Dong / Multi Music Type, AC, 230 Volts, Single Pole With Remote Controller complete all as specified and as directed.

S & F SP & N Enclosure with 2 Pole and Earth Metal Plug & Socket for incorporating SP MCB complete including One MCB, SP, 20 Amps, 240 Volts complete all as specified and as directed.

S & F Round Recess Mounted Energy efficient LED Tube Light Fitting, of not less than 1800 Lumens output, 5700 K of Cool White / Warm Light, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Round Recess Mounted Energy efficient LED Tube Light Fitting, of not less than 900 Lumens output, 5700 K of Cool White / Warm Light, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Energy efficient LED Decorative Golden / Rose Gold / Copper Metal Finish Chandelier Light Fitting including LED Bulbs not less than 6 Nos, 230 Volts, Roof / Recess Mounted with Acrylic / Frosted Glass Diffuser for soft glare free light with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95. Chandelier shall be as approved by the GE / User as per site requirement.

S & F Energy efficient Sleek LED Bed Side Light Fitting of not less than 500 Lumens, Surface / Recess mounted with Acrylic / PMMA diffuser for soft glare free light with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Surface / Wall mounted Energy efficient LED Tube Light Fitting, of not less than 1800 Lumens output, 5700 K of Cool White / Warm Light, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Surface / Wall mounted Energy efficient LED Tube Light Fitting, of not less than 900 Lumens output, 5700 K of Cool White / Warm Light, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Electronic wall mounted time delay Voltage stabilizer of 4 KVA Capacity, Automatic Operation, for input variation of 170 Volts to 250 Volts with stabilised voltage of 230 Volts with accuracy of ± 2.5% complete all as specified and as directed Make: V Guard / Servo / Kee Line

S & F Energy efficient, BEE 5 Star rated Storage type Water Heater [Geyser] of 15 Litres Capacity with 2000 Watt Capacity Heating Element, Conforming to IS - 2082, Vertical Storage type with Stainless Steel Inner Tank and ABS Outer Shell complete fixed to wall with suitable expansion fasteners including 15mm dia PVC Flexible Hot & Cold Water connections and 15mm bore Brass Chromium Plated Non-Return Valve complete all as specified and as directed. Make: Bajaj / Usha / Crompton Greaves / Jaquar

S & F MCB DB, TPN, 6 Way, 415 Volts, Vertical, with DIN Channel, N3 Frame, Double Door with 250 Amps rated bus bar, IP43 rated suitable for mounting MCBs and including MCB, TPN, 63 Amps, 16 KA, AC, 415 Volts, 50 Hz complete all as specified and as directed.

S & F MCB DB, SPN, 12 Way, 240 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs complete all as specified and as directed.

S & F MCB, SPN, 40 to 63 Amps, 10 KA, B Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCCB, TPN, 100 Amps, 25 KA, 415 Volts, 50 Hz, suitable for fixing on N3 Frame complete all as specified and as directed.

S & F MCB, SP, 6 to 32 Amps, 10 KA, B Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of single core 4 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. including One run of 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 3 Runs of 4 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit. Rate quoted is also deemed to be including cost of Cutting chases, pinning in Brick Walls, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, Cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of single core 6 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. including One run of 6 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 3 Runs of 6 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit. Rate quoted is also deemed to be including cost of Cutting chases, pinning in Brick Walls, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, Cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

M & L for Sub main wiring with 4 runs of single core 10 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 32 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. including Two runs of 10 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 6 Runs of 10 Sq.mm & one run of 32 mm dia PVC Conduit will be measured as one unit. Rate quoted is also deemed to be including cost of Cutting chases, pinning in Brick Walls, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, Cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

S & F Energy efficient, Low Noise, Ceiling Fan, 1200mm Sweep, BEE 5 Star Rated, with BLDC Motor, Copper Wound, 350 RPM, with Double Ball Bearing, Conforming to IS - 373, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50Hz, of approved colour including Down Rod, Canopies, 3 Nos. Blades, Shackles, Safety Rope, Hanging Clamps, Bushes and having P.F >0.94, Service Value >6.5, Air Delivery >215 CMM, Power Consumption less than 35 Watt, THD less than 5% with speed control by Electronic Regulator including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed.

S & F Exhaust Fan, 230mm Sweep, 1400 RPM, Metal Body, Heavy Duty, with Double Ball Bearing, Conforming to IS - 2312, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50 Hz, including Louvers Shutter / Grill, BEE 5 Star Rated and of approved colour including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Make: Crompton Greaves / Havells / Almonard / Bajaj / Orient

S & F Wall Mounted Fan, 450mm Sweep, Metal Body, Heavy duty, 230 Volts, AC, 50 Hz, Wall Mounting Type including speed control set and all accessories complete all as specified.

Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 4 mm GI Wire [Earth Lead] and GI pipe 15 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. complete all as specified and as directed.

Supply, install, testing and commissioning of 5 Star rated Hi-Wall Split Units Indoor / Outdoor with Cordless Remote Control Unit and with in-built advanced Air Filters for better indoor air quality with latest Inverter technology, having Eco friendly Refrigerant Gas, Copper Condenser Coil, EER 4.5 or above of Capacity 1.5 TR, Summer Cool, Inverter Compressor, Automatic 2D Swing Copper Condenser, BLDC Motor, necessary copper pipe connections including cutting, bending, brazing, insulation on pipe etc, PVC Drain Pipe, electric connection between indoor and outdoor unit with suitable size PVC insulated, multi-stranded copper cable complete all as specified and as directed. Make: Blue Star / Hitachi / Daikin / Carrier / Voltas Note: The rate quoted by the contractor is deemed to include for Powder Coated Mild Steel Fixing Brackets for Outdoor and Indoor Units at any height and Copper tube of suitable size, Drain Pipe made of High Density Polyethylene Pipes [HDPE] of pressure rating 6 KGf / Sq.cm of 20mm dia as required and 3 Core, 4 Sq.mm, PVC Insulated and PVC sheathed, heavy duty cable, ISI marked with Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade as required for connecting indoor and outdoor units.

GS ENGINEERS

RAJASHEKHAR ENTERPRISES

S R CONSTRUCTIONS

D A MURTHY AND SONS

ESWAR ENTERPRISES

SRI SAI KRISHNA ENGINEERING WORKS