Construction of New Sub Division office building at Samou Canal Colony of Dantivada Reservoir Project, Samou.

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

1 Excavation for foundation up to 1.5 m depth 178.00 CMT 122.94

including sorting out and stacking of useful

materials and disposing off the excavated

stuff up to 50 Meter lead.(A) Loose or soft

2 Excavation for foundation up to 1.5 m to 3.00 33.00 CMT 136.30

mt depth including sorting out and stacking

of useful materials and disposing off the

excavated stuff up to 50 Meter lead.(A)

Loose or soft soil

3 Filling in foundation and plinth with murrum 103.00 CMT 282.07

including watering, ramming and

consolidating etc. complete. (more than

4 Filling available excavated earth (excluding 167.00 CMT 136.92

rock) in trenches. plinth, sides of foundations

etc. in layers not exceeding 20 cm. in depth

consolidating each deposited layer by

ramming and watering.

5 Filling in plinth with sand under floors 35.00 CMT 444.75

including watering ramming, consolidation

and dressing etc. complete.

6 Providing and laying controlled cement 12.00 CMT 3845.06

concrete M.150 for curing complete

excluding cost of formwork and

reinforcement for reinforced concrete work in

(A) Foundations, footings,Base of columns

and Mass concrete

7 Providing TMT Bar FE 500D reinforcement 13550.00 Kg. 77.29

for R.C.C. work including bending, binding

and placing in position complete upto all

floor level.

8 Providing and laying controlled cement 32.00 CMT 4496.22

concrete M-250 with curing complete,

including the cost of formwork but excluding

the cost of reinforcement for reinforced

concrete work in Foundation footing base of

columns and mass concrete. (For any size)

9 Providing and laying controlled cement 10.00 CMT 7314.42

concrete M-250 and finishing smooth with

cuing etc. complete including the cost of

formwork but excluding the cost of

reinforcement for reinforced concrete work in

columns up to plinth level.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

10 Providing and laying controlled cement 17.00 CMT 5895.84

concrete M-250 and curing complete

including the cost of formwork but excluding

the cost of reinforcement for RCC work in

Ground beam and Plinth Beam.

11 Providing and laying cement concrete 1:3:6 37.00 CMT 2978.97

(1-Cement : 3- coarse sand : 6- hand broken

stone aggregates 40 mmnominal size) and

curing complete excluding cost of formwork

in (A) Foundation and Plinth

12 Brick work using common burnt clay building 12.00 CMT 4214.33

bricks having crushing strength not less than

35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:6. (1- Cement : 6 fine

sand) (b) Conventional

13 Providing and laying controlled cement 3.00 CMT 6342.92

concrete M-250 curing complete including

cost of Formwork but including cost of

reinforcement for wall caps/coping.

14 Providing and laying controlled cement 11.00 CMT 7761.21

concrete M.200 and curing complete

including the cost of formwork but excluding

the cost of reinforcement for reinforced

concrete work in Columns, Pillars posts and

struts at Ground floor.

15 Providing and laying controlled cement 21.00 CMT 6307.94

concrete M.200 and curing complete

including the cost of formwork but excluding

the cost of reinforcement for reinforced

concrete work in Beam at Ground floor.

16 Providing and laying controlled cement 34.00 CMT 6251.24

concrete M.200 and curing complete

including the cost of formwork but excluding

the cost of reinforcement for reinforced

concrete work in Slab at Ground floor.

17 Providing and laying controlled cement 6.00 CMT 8078.53

concrete M.200 and curing complete

including the cost of formwork but excluding

the cost of reinforcement for reinforced

concrete work in Lintel at Ground floor.

18 Providing and laying controlled cement 3.00 CMT 6605.59

concrete M.200 and curing complete

including the cost of formwork but excluding

the cost of reinforcement for reinforced

concrete work in Chhajja at Ground floor.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

19 Providing and laying controlled cement 2.00 CMT 4790.79

concrete M.150 for curing complete including

cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in

columns at First floor.

20 Brick work using common burnt clay building 97.00 CMT 4496.05

bricks having crushing strength not less than

35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:6. (1- Cement : 6 fine

sand) (b) Conventional (Ground Floor)

21 Brick work using common burnt clay building 12.00 CMT 4538.16

bricks having crushing strength not less than

35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:6. (1- Cement : 6 fine

sand) (b) Conventional ( First Floor )

22 (i) Half brick masonry in common brunt clay 9.00 SMT 684.26

building bricks having crushing strength not

less than 35 Kg/Sq.Cm. in Cement mortar

1:4 (1- Cement : 4 -coarse sand ) in

foundation and plinth (B) Conventional (

Ground Floor )

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

23 Charges for making holes in brick walls / 15.00 NOS 1045.35

RCC with or without plaster / tiles with

mechanical cutter like HILTI etc. Including

disposing the debris and finishing the same

as per requirements. Measurement of holes

will be taken per no. of holes drilled as per

following range of diameters. Making of

holes by hammer and chisel will not be

considered in this item. For Diameter of

holes up to 100 mm clear.

24 Providing and fixing window having extruded 22.00 SMT 1713.70

aluminum Colour anodized section frame

main outer size 63.50 x 38.10 x 1.95 mm,@

Wt 1.094 Kg / Rmt, horizontal Two track

member size 61.85 mm x 31.75 mm x

1.20mm @ wt.of 0.695 Kg/mt, vertical

member of size 61.85 mm x 31.75mm x

mm @ wt.of 0.659 Kg/mt with sliding

shutters of horizontal member size 40mm x

vertical member of size 40mm x 18mm x

Kg/mt with 5 mm thick transparent bronze

colour tinted float glass with powder coated

aluminum fittings and fixtures and

transparent silicon sealant glass fixing to

frame as per details etc complete for

25 Providing and fixing window having extruded 25.00 SMT 1583.95

aluminum Colour anodized section frame

main outer size 95mm x 24mm x 1.17mm @

wt.of 0.738 Kg/mt , horizontal Three track

member size 92mm x 31.75mm x

1.30mm,@ Wt.1.07 Kg/mt, vertical member

of size 92mm x 31.75mm x 1.50mm @ Wt.

1.06 Kg/mt with sliding shutters of horizontal

member size 40 mmx18mm x1.29mm @

wt.of 0.456 Kg/mt, vertical member of size

0.456Kg/mt/ with 5 mm thick transparent

bronze colour tinted float glass with powder

coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to

frame as per details etc

26 Providing and fixing standard extruded of 4.00 SMT 1525.00

aluminum section of size 63.50 x 38.10 x

1.95 mm(of Jindal Section no:4605,@ Wt

1.094Kg / Rmt with color anodized

aluminum frame with 5 mm thick

transparent bronze color tinted float glass

as details etc complete for Fix window.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

27 Providing and fixing FRP frame size 125x65 6.00 SMT 2615.04

mm and 35mm thick FRP shutter having

extra reinforcement on sides & edges in

polish finish. The core of the shutter & frame

is to be filed up with injected polyurethene

foam done in situ alongwith embedded

wooden pieces for stiffening & also taking

hinges & fintures. The whole FRP frame &

shutter is to be water proof weather proof,

termite proof & resistance to mild acid/alkali.

Rates are to be inclusive of S.S hinges with

necessary screws & alluminium S.S fixtures

& fastenings & astener sleeve.

28 Provoding and fixing flush door shutters, 26.00 SMT 1829.74

solid core construction with frame of first

class hardwood with cross board and face

veneer or plywood face panels, including

anodised alluminium butt hinges with

necessary screws. (B) Non-decorative type

and block board core anodised alluminium

butt hinges in flush door shutters (2) 35 mm

29 Providing and fixing standared extruded of 1.50 SMT 1290.81

alluminium section of size 63.50 x 38.10 x

1.95 mm @ Wt 1.094Kg / Rmt with colour

Powder Coated alluminium frame with 5 mm

thick transparent bronze colour tinted float

glass with colour anodized alluminium frame

for ventilation with 5 mm thick frosted glass

as details etc complete for.window

30 providing and fixing hydraulic door closer 10.00 NOS 875.27

with screws to pivoted / hinged door of

approved make & color approved. Rate shall

be inclusive of fixing with using the template

as per supplier's specification.

31 providing and fixing dead lock of approved 3 11.00 NOS 1509.95

lever in doors with necessary screws and as

per drawing, complete as approved by

architect or engineer in charge.

32 providing and fixing S.S. Pipe Handle for 11.00 NOS 2150.61

door 30 Cm size o ASIS 316 Grade finish

push -pull handles in pair of two, with

necessary screws etc. Complete, as per

drawing as approved by architect or

engineer in charge. Two pieces of handle

shall be considered as one no. for

measurement & payment.

33 Fixing Metallic tower bolts of sizes with 11.00 NOS 51.45

necessary screws etc. complete

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

34 Providing & fixing 75 mm S.S. 316 satin 14.00 NOS 987.78

finish baby latch (kitch or equivalent

approved make ) with indication of

occupancy ( flat / round ) of kitch of

equivalent with necessary screws etc.

Complete as approved by Architect or

Engineer-in- charge with indication of

occupancy.

35 Providing & fixing 75 - 100 mm white PVC 11.00 NOS 40.40

door buffer with necessary screws etc.

Complete as approved by Architect or

Engineer-in-charge.

36 Providing fabricating, erecting and fixing of 1697.50 KG 109.08

M.S.grill, fabricated from m.s. plat, angles,

tees, spacebar, round bar, pipes etc.

complete as per Architect detail & Drawing

including applying one coat of red oxide &

two coat synthetic enamel paint etc

complete. As per Architect instructions and

drawing or as directed by engineer in

37 providing and fixing stainless steel railing 20.00 RMT 2426.87

made from anticorrosive 304 grade s.s. pipe

of 50mm dia (16 gage) as hand rails.s.

grade baluster as vertical support fixed in

r.c.c. slab at 1.00 T0 1.20 mt c/c and height

should be 900 mm including accessories as

per detail drawing as directed etc complete

as approved by engineer in charge

38 Providing 10mm thick cement plaster in 224.00 SMT 138.64

single coat on brick/concrete walls for

interior plastering upto floor two level and

finished even and smooth in (i)Cement

mortar 1:3 (1-cement:3-sand). Ground Floor

39 Providing 15mm thick cement plaster in 691.00 SMT 165.02

single coat on Rough (Similar)side of single

or half brick walls for interior plastering upto

floor two level and finished even and smooth

in (ii) Cement mortar 1:4 (1-cement :4-sand)

Ground floor

40 Providing 15mm thick cement plaster in 161.00 SMT 188.92

single coat on Rough (Similar)side of single

or half brick walls for interior plastering upto

floor two level and finished even and smooth

in (ii) Cement mortar 1:4 (1-cement :4-sand)

First floor

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

41 Providing and fixing 24 gauge - GI chicken 57.00 SMT 288.87

wire mesh (PLASTER MESH OF AMAX

INTERNATIONAL) at the junction of

masonry work and RCC work or on any

other place as directed to receive plaster

including fixing with galvanized nails, raw

plugs at all heights plinth level- including

scaffolding etc complete as directed.

42 Providing and applying 20mm thick sand 379.00 SMT 320.70

faced/mala cement plaster on walls upto

required height above ground level

consisting of 12mm thick backing coat of

C.M. 1:3 (1-cement : 3-sand) and 8mm thick

finishing coat of C.M. 1:1 (1-cement : 1-

sand) etc. complete.

43 Finishing wall with water base primer (one 540.00 SMT 108.13

coat) and weather proof exterior emulsion

paint on wall surface (two coats) to give an

required shape even shade after thoroughly

brushing the surface to remove all dirt, and

remains of loose powdered materials.etc

44 Applying two coats of putty & two coats of 691.00 SMT 123.78

primer of approved brand and manufacture

on new wall surface to give an even shade

including thoroughly brushing the surface

free from mortar dropping and other foreign

matter and sand papered smooth and

painting (two coats) with plastic emulsion

paint of approved brand and manufacture on

wall surface to give an even shade including

throughly brushing the surface free from

mortar droppings and other foreign matter

and sand papered smooth.

45 Applying two coats of putty & two coats of 224.00 SMT 129.30

primer of approved brand and manufacture

on new ceilings and sloping roof surface to

give an even shade including thoroughly

brushing the surface free from mortar

dropping and other foreign matter and sand

papered smooth and Wall painting (two

coats) with plastic emulsion paint of

approved brand and manufacture on ceilings

and sloping roof surface to give an even

shade including throughly brushing the

surface free from mortar droppings and

other foreign matter and sand papered

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

46 P & L 24" x 24" vitrified 8 mm thick tile 8.00 SMT 1467.72

flooring over 20 mm (average) base of

cement mortar 1:6 ( 1 cement: 6 coarse

sand) on new surface or fixing on existing

flooring by adhesive material including

dismentaling of existing flooring and jointed

with color cement slurry including finised with

flush pointing & cleaning the surface etc.

complete for antiskit

47 Providing and laying Vitrified tiles 8 to 10 65.00 SMT 1195.02

mm thick , 24'' x 24'' in dedo on 10mm thick

cement plaster 1:3 (1-cement : 3 coarse

sand) and jointed with white cement slurry.

48 P & L 600 x 1200 vitrified 8 mm thick tile 211.00 SMT 1517.02

flooring over 20 mm (average) base of

cement mortar 1:6 ( 1 cement: 6 coarse

sand) on new surface or fixing on existing

flooring by adhesive material including

dismentaling of existing flooring and jointed

with color cement slurry including finised with

flush pointing & cleaning the surface etc.

complete for antiskit

49 Providing and laying Vitrified granite tiles 15.00 SMT 1592.40

8mm to 10 mm thick in skirting risers of

steps and dado on 10 mm. thick cement

plaster 1:3 (1 cement : 3 coarse sand)

pointing in white cement and jointed with

white cement slurry.

50 Providing and laying rough chiseled dressed 11.00 SMT 576.79

stone flooring over 20mm average thick

base of cement mortar 1:5 (1-Cement : 5-

coarse sand) or L.M. 1:1.5 (1-Lime putty :

1.5 - coarse sand) including pointing with

cement mortar 1:2 (1-cement : 2-stone dust)

etc. complete. (A) 25mm thick (up to 10 ton)

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

51 Providing & fixing granite stone average 18 68.00 SMT 3566.31

mm thick (16-18 mm) machine-cut &

machined polished stone in treads of steps,

sill, copings, parapet top, window sill, planter

top, and such other locations, laid on

mm(average) thick cement mortar 1:4 (1

cement:4coarse sand) and jointed with

Super flex guranted fixing solution by

kerakoll mixed with pigment to match the

shades of the slabs, including rubbing and

polishing complete. The Stone used should

be in one single long piece up to 3000 mm

as per drawing or as directed by Engineer-in-

charge. The exposed projected edges shall

be of uniform thickness and of uniform

projection including molding , chamfering,

rounding, polishing complete. as directed by

52 Providing & fixing sandwich type average 18 76.00 RMT 1113.02

mm thick (16-18 mm) machined polished

GRAINITE stone molded door frame of inner

trip 130mm X18mm wide and outer trip

150mm X 18mm wide jointed with Super

flex guranted fixing solution by kerakoll

mixed with pigment to match the shades of

the slabs, including rubbing and polishing

complete. The Stone used should be in one

single long piece as per drawing or as

directed by Engineer-in-charge. The

exposed projected edges shall be of uniform

thickness and of uniform projection including

molding , chamfering, rounding, polishing

complete as directed by EIC.

53 Providing and laying broken china mosaic 243.00 SMT 779.70

flooring for terrace using 12 mm to 20 mm

broken pieces of glazed tiles to be laid over

cement mortar 1:3 to plain or slope and to be

tempered to bring mortar creme out up to

surface using white cement including

rounding off junctions and extending them

up to 15 cm along the wall, clearing with

water and oxalic acid etc. as directed.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

54 Providing and fixing up to 1500 mm x 600 2.00 SMT 3022.93

mm partitions of 18mm thick (16-18 mm)

polished granite stone, in walls in CM 1:2

including making zaris 25 mm deep, fixing

and making good all around and both side

mirror polishing to granite stone, complete

as per drawing and directed by engineer and

architect. The rate shall includes rounding,

champhering and polishing of edges.

55 Providing erecting and fixing double coated 2000.00 LITE 3.95

ISI water tank of required capacity each with R

all necessary fittings and connection etc.

complete on terrace.

56 providing and fixing (A) White glazed 1.00 NOS 18393.11

vitreous chinaware extended wall mounted

cantilever type European type water closet

with Hydrolic seat cover, with (B) flushing

tank constellation cistern with cistern fittings,

CI chair bracket with rag bolt and GI 12mm

rag bolt with nut and metal washer etc.

including supply and fixing of (C) 1 no CP

heavy duty angle cock with CP wall flange

with CP brass inlet connection with integral P

or S trap including cutting and making good

the wall and floor as under with supported on

CI wall brackets and (D) flush cock 25 mm

etc. complete to the satisfaction of EIC.

57 providing and fixing (A) white glazed 2.00 NOS 3545.10

vitreous chinaware European type water

closet with seat cover, with , CI chair bracket

with 12mm rag bolt nut and metal washer

etc. including supply and fixing of (B) 1 no

CP heavy duty angle cock with CP wall

flange with CP brass inlet connection with

integral P or S trap including cutting and

making good the wall and floor as under with

supported on CI wall brackets and (C) flush

cock etc. complete to the satisfactionof EIC

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

58 Providing and fixing washbasin with single 3.00 NOS 5080.30

hole for pillar tap with C.I. or M.S. brackets

painted white including sutting holes and

making good the same including fittings.(a)

Vitreous China:(ii) Flat Back washbasin

mm x v 400mm size. (i) In white colour. (b)

32mm CP cast brass bottle trap heavy

casted, with 250mm long wall connection

pipe and wall flange with rubber adopter for

waste connection and one 40mm dia waste

coupling. (c) 1 no heavy quality CP brass

angle cock with wall CP flange (d) 15 mm

size. pillar cock with fitting complete. (e)1 no

15mm NB heavy quality CP brass inlet

connection with unions end. the supporting

bracket shall be painted with 3 coats of

approved paint of approved shade etc

59 providing and fixing screw down brass 3.00 NOS 2466.42

chromium plated heavy quality two way bib-

tap on water supply pipe lines of 15mm dia

with or with extension piece but with a flange

etc. complete to the satisfaction of EIC.

60 providing and fixing 15 mm knob cp brass 1.00 NOS 2666.40

heavy quality wall or floor mounted sink tap,

with cp wall flange, casted spout of three

way etc. complete to the satisfaction of eic.

61 Providing and fixing 600mm x 450mm 3.00 NOS 859.41

bevelled edge mirrror of superior glass

mounted on 6mm thick A.C. sheet or

plywood sheet and fixing to wooden pluge

with C.P. brass screws and washers.

62 Providing and fixing C.P. brass towel rail 1.00 NOS 616.42

comlete with C.P. brass brackets fixed to

wooden plugs with C.P. brass scews.(B)

600mm x 20mm size.

63 providing and fixing ss or brass chromium 2.00 NOS 944.35

plated double robe hook as per the design

and specifications etc., complete to the

satisfaction of eic.

64 Providing and fixing toilet paper holder.(A) 3.00 NOS 375.82

C.P. Brass

65 providing and fixing hand shower (health 3.00 NOS 582.03

faucet) with cp flange with 8 mm dia., 1 m

long pvc tube and wall hook with fitting . as

approved by the consultants.

66 Providing and fixing Urinal of approved 2.00 NOS 1630.20

quality including connection with trap and

with integral longitudinal flush pipe.(A)

Squating plate pattern white earthenware

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

67 providing and fixing to wall, ceiling and floor, 60.00 RMT 431.27

SWR quality, heavy duty 6KG/RMT pvc

pipes of finolax / astral or equivalent make

as approved by eic,, open laid for soil / waste

/ rain water etc complete, with necessary

specials, bends, such as Y junction T

junction (both single and double) including

plugs, shoes, cowls flange compression type

fittings, wall clips, in proper line and level

with necessary support like split clamps of

chilly make 3mm minimum thickness fixed

with approved anchor fasteners ,RCC or

brick pedestals or battens if necessary to

wall, ceiling and floor, open laid complete

jointing with suitable grade of good quality

solvent cement (as recommended by the

manufacturer) including testing, cutting,

making good the wall, ceiling and floor, etc

complete to the satisfaction of EIC of the

following OD. 110 mm 6 Kg.F/cm

68 providing and fixing to wall, ceiling and floor, 50.00 RMT 282.80

SWR quality, heavy duty 6KG/RMT pvc

pipes of finolax / astral or equivalent make

as approved by eic,, open laid for soil / waste

/ rain water etc complete, with necessary

specials, bends, such as Y junction T

junction (both single and double) including

plugs, shoes, cowls flange compression type

fittings, wall clips, in proper line and level

with necessary support like split clamps of

chilly make 3mm minimum thickness fixed

with approved anchor fasteners of HILTI

equivalent ,RCC or brick pedestals or

battens if necessary to wall, ceiling and floor,

open laid complete jointing with suitable

grade of good quality solvent cement (as

recommended by the manufacturer)

including testing, cutting, making good the

wall, ceiling and floor, etc complete to the

satisfaction of EIC of the following OD.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

69 providing and fixing to wall, ceiling and floor, 20.00 RMT 738.31

SWR quality, heavy duty 6KG/RMT pvc

pipes of finolax / astral or equivalent make

as approved by eic,, open laid for soil / waste

/ rain water etc complete, with necessary

specials, bends, such as Y junction T

junction (both single and double) including

plugs, shoes, cowls flange compression type

fittings, wall clips, in proper line and level

with necessary support like split clamps of

chilly make 3mm minimum thickness fixed

with approved anchor fasteners of HILTI

equivalent ,RCC or brick pedestals or

battens if necessary to wall, ceiling and floor,

open laid complete jointing with suitable

grade of good quality solvent cement (as

recommended by the manufacturer)

including testing, cutting, making good the

wall, ceiling and floor, etc complete to the

satisfaction of EIC of the following OD.

70 Providing laying and jointing in true line and 50.00 RMT 72.65

level 15mm dia. U.P.V.C. Pipe ( SCH- 40)

for cold water including fittings as approved

by Engineer In Charge. Pipe shall be fixed

on the wall with the help of clamp at every

two metre C/C or shall be concealed as

directed including necessary fittings etc.

including testing of pipe and joints and fixing

the same with adhesive solvent, including

cost of all materials.

71 Providing laying and jointing in true line and 70.00 RMT 91.84

level 25mm dia. U.P.V.C. Pipe ( SCH- 40)

for cold water including fittings as approved

by Engineer In Charge. Pipe shall be fixed

on the wall with the help of clamp at every

two metre C/C or shall be concealed as

directed including necessary fittings etc.

including testing of pipe and joints and fixing

the same with adhesive solvent, including

cost of all materials.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

72 Providing laying and jointing in true line and 50.00 RMT 148.12

level 40mm dia. U.P.V.C. Pipe ( SCH- 40)

for cold water including fittings as approved

by Engineer In Charge. Pipe shall be fixed

on the wall with the help of clamp at every

two metre C/C or shall be concealed as

directed including necessary fittings etc.

including testing of pipe and joints and fixing

the same with adhesive solvent, including

cost of all materials.

73 Providing laying and jointing in true line and 40.00 RMT 195.67

level 50mm dia. U.P.V.C. Pipe ( SCH- 40)

for cold water including fittings as approved

by Engineer In Charge. Pipe shall be fixed

on the wall with the help of clamp at every

two metre C/C or shall be concealed as

directed including necessary fittings etc.

including testing of pipe and joints and fixing

the same with adhesive solvent, including

cost of all materials.

74 providing and fixing cast iron steps of size 10.00 NOS 207.66

500mm x 150mm x 22.5mm and painting

with two coats of Anti- corrosive paint

etc.complete. as per architect instruction.

75 Providing cement vata (10 cm x 10 cm size) 33.00 RMT 24.28

quarter round in cement mortar 1 :1

including neat cement finishing watering etc.

complete as per architect instruction.

76 Constructing sandwitch platform ofn18mm 3.00 SMT 3223.92

thick polished black granite at top and 25mm

thick kota stone slab using cement mortar

1:3 for sandwich and fitting at bottom &

edges with water proof rigid adhesives

including macking necessary grooves in

walls with vertical kotastone 30mm X 2no

sandwitch thick every 60cm center to center

including alll labour material of approved

quality incl. full moulded round front edge

fixed in wall for partition and jointed with grey

cement slurry including rubbing and

polishing etc. complete

77 Providing and fixing Gun metal check or non- 2.00 NOS 663.43

return fullway wheel valve.(E) 40mm dia.

78 Providing and fixing Gun metal check or non- 2.00 NOS 420.63

return fullway wheel valve.(C) 25mm dia.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

79 Providing and fixing PVC SWR Nahni Trap 10.00 NOS 733.26

IS 14735 for drain - 100 mm diameter with

jali of the following nominal diameter of self

cleansing design with C.I. screwed down or

hinged grating including the cost of cutting

and making good the walls.e As per

Architect instructions and drawing or as

directed by engineer in charge.

80 Providing and fixing S.W. gully trap with C.I. 6.00 NOS 1292.19

grating brick masonry chamber and water

tight C.I. cover with frame of 300mm x

300mm size (inside) with standard weight.(i)

Square mouth traps (A) 100mm x 100mm

size P type. (up to. 10 ton)

81 Constructing brick masonry chamber for 2.00 NOS 7180.44

underground C.I. Inspection chamber and

bends with bricks having crushing strength

not less than 35Kg. Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x

610mm internal dimensions total weight of

cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg.

) (R.C.C. top slab with 1:2:4 mix (1-cement

:2- coarse sand :4- graded stone aggregate

20mm size) foundation concrete 1:5:10

inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed

concrete etc. complete.(iii) Inside

dimensions 600mm x 850 mm and 450mm

deep for pipe lines with three or more inlets.

(up to 10 ton)

82 Providing and fixing ball cock of approved. 2.00 NOS 189.84

quality as directed.(A) Copper Metal 50mm

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

83 Providing & constructing BB masonry in 1.00 NOS 29122.34

C.M. 1:6 (1 cement : 6 coarse sand) and

cement concrete 1:2:4(1 cement : 2 sand :

graded stone age. of 0mm size BT kapchi)

septic tank of 3m x 0.9 m x 1.5 m internal

dimension with necessary compartment of

grit chambers and septic tank with

necessary inlet and outlet connections with

cement plaster (15 mm thick) in C.M. 1:4 (1

cement : 4 sand) with water proofing

material 1:5:10 (1 cement : 4 sand) brick bat

concrete bedding RCC 1:2:4 top cover slab

12 cm thick with C.I. cover of 60 cm x 45 cm

size (light duty) 75mm dia. C.I. ventilating

pipe 2 mt. long with cowl vent 40mm thick

IPS flooring 10 cm. thick cement vata mild

steel for steel and finishing to exposed faces

in C.M. 1:3 (1 cement : 3 sand) curing etc.

complete As per Architect instructions and

drawing or as directed by engineer in

84 Providing and constructing sock pit of 3.00 1.00 NOS 51550.40

mt. dia inside and 5.00 mt. depth with honey

combed masonry upto 4.00 mt. from bottom

and 1.00 mt. brick masonry in C.M. 1:5 top

with RCC slab cover of M200 vent pipe

mt. long 75 mm dia & C.I. cover and cowl

vent etc. complete

85 Providing and fixing in position cowel went to 4.00 NOS 393.04

pipes.(B) 75 mm dia.

86 Providing and fixing in position cowel went to 4.00 NOS 505.17

pipes.(B) 100 mm dia.

87 Providing and fixing single layer waterproof 32.00 SMT 606.95

gypsum board 12.5 mm thick of the make

Newgood Group Co. Ltd. Or equivalent &

Newgood Group Co. Ltd. company sections

using waterproof board of size 1220 mm x

1830 mm x 8.0 mm suspended by G.I

suspender of size 25 mm x 3 mm with

intermediate channel of size 18 mm x

mm x 0.80 mm at 1220 mm center to center

ceiling section of size 40 mm x 35 mm x

0.55 mm at 457 mm center to center and

perimeter channel A of size 20 mm x 27 mm

x 30 mm x 0.50 mm at edges & drops

including paper tap sand soffit cleat, anchor

fastener, scotch bolt connecting cleat joining

compound top coat on ceiling including

making necessary opening for light fitting,

diffuser etc. complete as per detail drawing

as directed.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

88 Providing and fixing screw down bib taps of 4.00 NOS 186.83

following size.(B) Brass chromium plated

screws down Bib Tap. (i) 15mm dia.

89 Providing and fixing pillar tap, capstan head, 1.00 NOS 308.73

screw down high pressure with screws,

shanks and back nuts. (i) 15mm dia.

90 Providing and fixing brass screw down stop 6.00 NOS 220.82

tap.(C) 25mm dia..

91 Providing and fixing SS Sink Glosy ASIS 304 1.00 NOS 3042.12

Grade x 1mm thick with over all size

610x460 mm & bowl size 560x410x200 with

single hole for pillar tap fixing in sandwitch

platform including cutting holes and making

gods the same, necessary fixtures,

connections and waste pipes with c.p. pillar

cock 15mm heavy duty swan neck etc

92 Providing throating or plaster drip and 47.00 RMT 43.05

moulding to R.C.C. Chhajja.or grove plaster

93 Providing and laying marble stone Goda 107.00 Smt 2098.78

kabat over 20mm (average)base of cement

mortar 1:6 (1-cement : 6 coarse sand) or

L.M. 1:1.5(1- lime putty : 1.5 - coarse sand)

laid and jointed with gray cement slurry

including rubbing and polishing complete.

(A) Marble slab 18 to 20mm thick

94 Point wiring for Light / Bell with 2-1.5 45.00 PT 389.86

sq.mm & earthwire of 1.5 sq.mm (Green)

both are of ISI marked 1.1 KV grade FRLS

PVC insulated multistrand copper wires, in

following type of pipe to be erected

concealed in/ on surface on wall/ceiling

complete with 6A Modular type switch / bell

push & accessories and earth continuity of

following type, erected on PVC / Metallic

box, single mounting base frame covered

with textured/metallic front plate modules

erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ceiling

rose / H.D.Connector as directed. (e) in

existing pipe erected flushed on wall/ceiling

complete CAT III

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

95 Point wiring for FAN with 2-1.5 sq.mm & 10.00 PT 547.42

earthwire of 1.5 sq.mm (Green) both are of

.ISI marked 1.1 KV Grade FRLS PVC

insulated multistrand copper wires, in

following type of pipe to be erected

concealed in / flushed on wall/ceiling

complete with 6A Modular type switch and

hum free EME four or more step type

electronic fan regulator with separately

mounted and accessories with earth

continuity of following type erected on PVC /

Metallic box, single mounting base frame

covered with textured/metallic front plate

modules erected on / in wall / ceiling as per

pipe erected. with necessary ceiling rose /

H.D.Connector as directed. (e) in existing

pipe erected flushed on wall/ceiling

completeCAT III

96 Point wiring for Looped Plug with 6A Modular 16.00 PT 268.66

type switch & 5 pin socket erected on PVC /

Metallic box, single mounting base frame

covered with textured / metallic front plate

modules erected on / in wall / ceiling with

following type accessories. CAT III

97a (7)Blank Plate Single Cat III 10.00 NO 28.28

97b (8) Moderm jack RJ45 Cat III 6.00 NO 179.78

97c (11) 6 Amp. Bell push cat III 1.00 NO 168.67

97d (19) Modular Indicating Call Bell 1.00 NO 369.66

97e (24) Angle holder cat III 4.00 NO 71.71

98 Providing & erecting Switch board for 6.00 NO 1274.62

Computer or electric apparatus consisting of

following modular type accessories mounted

with PVC / Metallic concealed/open box

with single mounting base frame covered

with textured/metallic /white front

plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch

combined. 3 nos. 6A Switch 3 nos. 6A 5 pin

Plug For Modular Type AccessoriesCat. III

99 Providing and erecting ISI mark Medium 330.00 MTR 26.26

class RIGID PVC PIPES of following size

complete to be erected on/in wall or ceiling

erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution

& Clamps with following dia of pipes, in

approved manner as directed (b) 20 mm

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

100 Mains with 1.1 KV grade FRLS PVC 180.00 Mtr 68.68

insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour

for earth continuity of following size (E) in

existing pipe (b) 2 wire 2.5 sq. mm

101 Mains with 1.1 KV grade FRLS PVC 155.00 Mtr 95.95

insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated

stranded wire of green colour for earth

continuity of following size (E) in existing

pipe (a) 2 wire 4 sq. mm

102 Supplying & erecting approved make LAN 175.00 Mtr 51.51

cable of following size in existing pipe as per

direction ( C) CAT

103 Providing & erecting Approved make Power 10.00 No 2090.70

Saving 50 Watt Ceiling Fan with double ball

bearing ISI mark with Condenser 230 volt

A.C. 50 Hz 1200 mm sweep complete

having 3blades with aluminium blades with

canopy & 30 cms. down rod erected with 24/

0.2, 3 core flexible wire with earthing.(Make

shall be approved by Engineer in charge)

104 Supplying and erecting 19 / 20 mm. nominal 5.00 MTR 126.25

bore Medium Class M.S. Pipe down rod

erected duly painted for fan complete with

proper insulation without leakage and

105 Supplying & erecting Fan Hook of 10 mm 10.00 No 50.50

M.S. Round bar grouted in RCC slab with

Making the site as original.

106 Supplying & erecting approved make low 4.00 No 2009.90

noise decorative exhaust fan having square

frame ABS body with inbuilt lowers & square

frame. 200 mm with 1350 rpm cat III

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

107 Supplying and erecting LED indoor fittings 8.00 NO 555.50

with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing

used as a heat sink shall be made of thick

sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion

resistance with diffuser housed in

aluminium casted body with company

mark/name 160V to 270V,Power Factor

more than 0.9, THD < 15 %, CCT 3000 K to

6500K, Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

any wattage capacity between the ranges

shown.)(A) Square/ Circular shaped

Surface/Recessed Mount Downlight with

provision for spring loaded mounting clips

complete.IP20 (ii) 11-15 watts, Surge-2 KV

108 Supplying and erecting LED indoor fittings 30.00 NO 383.80

with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing

used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high

U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power

Factor more than 0.95, THD < 15%,CCT

3000 K to 6500K, Luminaire efficacy>

lumens/watt ,LED LED driver efficiency >

%( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

any wattage capacity between the ranges

shown.) (A) Tube Light with integral driver

(lll) 18-20 Watts, Surge - 2KV,IP-20, 4 feet

109 Supplying and erecting led lamps with 4.00 no 146.45

following wattage capacity of 220 to

voltage, minimum 15000 burning hours life,

500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 /

B22 lamp holders, pf >= 0.5 (A) LED Lamps

integral type, with PC diffuser suitable LAMP

holder( ll ) 5 to 8 watts Cat-lll

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

110 Providing & Erecting 3mm thick acrylic Sheet 420.00 NO 3.03

with grooving as directed.

111 Providing and erecting Sheet Steel powder 1.00 NO 4025.86

coated MCB distribution board - flush /

surface mounted fitted with busbar, neutral

link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to

house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to

be used) suitable for (B) three phase

incoming and single phase horizontal type

outgoing Per phase isolation type (PPI)(b)

sheet steel double door (iv)8 way

112 Providing and erecting Sheet Steel powder 1.00 NO 1759.42

coated MCB distribution board - flush /

surface mounted fitted with busbar, neutral

link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to

house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to

be used) suitable for(A) single phase

incoming and horizontal single phase

outgoing(b) sheet steel double door (IP-43)

(iv)12 way

113 Providing & erecting 415 V MCB Four Pole 1.00 NO 868.60

for Motor & Inductive Load (C Curve) having

10KA breaking capacity & confirms to IS

:8828 in existing box having following

capacity (C)63 Amp. Cat.III

114 providing and erecting Approved make 4.00 NO 2636.10

RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit

withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz.

having characteristic of quick action &

tripping with all advance feature & do not

incorporate any electronic component. for

following Max. rating erected as directed (iii)

40 Amps. DP DP Cat. III

115 providing and erecting Miniature circuit 28.00 NO 131.30

breaker single pole 6A to 25A suitable to

operate on 240 V A.C. system and having

breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with

ISI Mark (B) Cat.III

116 Supplying KITKAT pattern porcelain cut-out 3.00 NO 494.90

fuse with base of following current capacity

erected on existing block board.(vi) 200 A.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

117 Providing and erecting XLPE(IS:7098)(I)-88 5.00 MTR 211.09

ISI armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench /

pipe of following size of cables (A) 3 1/2

core 25 Sq. mm ( 16 Sq. mm 1/2 core)

118 Making trench in soft soil of suitable width of 5.00 mtr 54.54

90 cm deep for laying cable or locating the

fault all over the run and back filling the

same and making the surface as normal

119 Supplying & erecting earth pit of minimum 1.00 no 5416.63

bore dia.150mm size approved make

Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of

corrosion free hot dipped G.I. Pipes having

Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm

having 200-250 Micron galvanising,

connection terminal dia of 12 mm with

constant ohmic value surrounded by highly

conductive compound with high charge

dissipation suitable for following type of

applications with chamber and heavy duty

cover. (approved make OEM has to submit

test certificate) & having back filling

compound of (B) Inner chemical (CCM

Compound) - Resistivity :- 0.2/ meter testing

as per IEC 62561-2017, Voltage drop:- <

volt at no load & dry form, Sulphar content:-

<2% (C) Back fill Compound :- Earthing

compound should be capable to retain

moisture for long time Necessary test report

must be submitted. (a ) For Electrical

installation up to 440V in normal soil. Length

of Pipe : 1.00 mtrs. Back filling Compound :1

no. Bag of 15 Kg

120 Providing and Erecting Annealed bare 1.00 Kg 937.28

Copper wire 8 to 16 SWG

121 Providing & erecting open well type 1.00 No 9519.25

horizontal mono block pump set with

stainless steel body having following

specification (C) 1 H.P. single phase open

well motor pump set suitable for 185 LPM

discharge @ 25 mtr. head, suitable for

mm dia. Delivery pipe with control panel.

122 Supplying & erecting XLPE(IS:7098)(I)-88 32.00 mtr 159.58

ISI unarmoured copper cable 1.1 KV grade

to be erected as directed of following size.

(E) 3 core 2.5 Sq. mm

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

123 WORK TABLE - A : (1.80m x 0.75m x 0.85) 2.00 NOS 18180.00

Providing and fixing 25 mm thick plywood

with laminate top in approved shade with

telescopic suspended metal key board with

mouse tray with 57 mm vertical legs made

by plywood with exterior side laminate and

interior side 0.8 mm approved laminate .

Drawer and side box should be made from

ply wood with laminate finish as per detail

drawing with wooden bedding patti or nylon

castor with lock, Knobs/handel and

telescopic channel should be made from

19mm plywood with 1.00 mm laminate

outside and 0.8mm laminate inside of

shutters with auto hinges of hafele or

equivalent and drawer should made from

mm post forming , laminate inside and

laminate of approved make and foot rest

should be made of 19mm ply with 1 mm

laminated finish in approved shade-including

all materials and labours etc. complete as

per detail drawing and instruction of engineer

–in charge and detail specification.

124 WORK TABLE - B : (1.50m x 0.75m x 0.85) 5.00 NOS 15150.00

Providing and fixing 25 mm thick plywood

with laminate top in approved shade with

telescopic suspended metal key board with

mouse tray with 57 mm vertical legs made

by plywood with exterior side laminate and

interior side 0.8 mm approved laminate .

Drawer and side box should be made from

ply wood with laminate finish as per detail

drawing with wooden bedding patti or nylon

castor with lock, Knobs/handel and

telescopic channel should be made from

19mm plywood with 1.00 mm laminate

outside and 0.8mm laminate inside of

shutters with auto hinges of hafele or

equivalent and drawer should made from

mm post forming , laminate inside and

laminate of approved make and foot rest

should be made of 19mm ply with 1 mm

laminated finish in approved shade-including

all materials and labours etc. complete as

per detail drawing and instruction of engineer

–in charge and detail specification.

Description of Item (with brief

It. Rate in Amount in

specification and reference to book of Quantity Unit

specifications)

125 HIGH BACK REVOLVING CHAIR:- 2.00 NOS 6060.00

Manufacturing and Supply of High Back

Revolving Chair 1. Seat And Back : 12MM +

6 MM Doubble Hot Press Ply Use In Back

and Waterfall Design 16 MM Hot Press Ply

Use In Seat for better thigh Support.

2. U-Foam : 32 D Feather Foam Use in Back

3. Mould : 45D PU Mould Cushion Use in

Seat Synchro Mechanism with single

position locking system. 4. Arm Rest :

Chrome Finish arms with PU Pad

Mechanisam : Syncro mechanism with

Singel Loking 6. Base :Powder Coated five

pronged base 7. Gas Lift : 100 MM Class

ANSI/BIFMA Tested (5 Year Warranty)

Caster : Twin wheel castors are injection

moulded in nylon and diameter of Castor

mm.(2 Year Warraanty )

126 Staff chair : providing and fixing revolving 11.00 NOS 3838.00

chair with net back as per photo with

S.S./M.s. frame structure, pu form and pu

leather as per engineer instruction. (2 Year

Warraanty )

127 CHAIR:- providing and placing modular 15.00 NOS 2525.00

armless non revolving chairChair frame

with backrest Frame: Steel, Epoxy/polyester

powder coating Back: Reinforced

polypropylene plastic Seat cover:

Polypropylene plastic Seat: Coated fabric:

75% polyester, 25% cotton, 100%

polyurethane ,Seat frame: Layer-glued wood

veneer Seat foam: Polyurethane foam

kg/cu.m. size - Width: 45 cm (17 3/4 ")

Depth: 51 cm (20 1/8 ") Height: 81 cm (31

7/8 ") Seat width: 44 cm (17 3/8 ") Seat

depth: 44 cm (17 3/8 ") Seat height: 46 cm

(18 1/8 ") Max. load: 110 kg (243 lb) (2 Year

Warraanty )

Total Amount Rs.

Total Amount Rs.

Executive Engineer

Deesa Irrigation Division